Resources

A horizontal square wire frame of side length L=0.30 mL = 0.30\text{ m} and mass m=0.045 kgm = 0.045\text{ kg} with electrical resistance R=0.25 ΩR = 0.25\ \Omega rests on a rough horizontal laboratory tabletop where the coefficient of static friction is μs=0.30\mu_s = 0.30. A uniform vertical magnetic field passes through the frame. The magnetic field begins increasing at a constant rate dBdt\frac{dB}{dt}. A researcher places a small permanent bar magnet just beside one of the loop's segments such that this segment (length L=0.30 mL = 0.30\text{ m}) experiences an external localized horizontal magnetic field Bext=0.50 TB_{\text{ext}} = 0.50\text{ T} perpendicular to the wire segment. What is the critical threshold rate of change of the primary magnetic field, (dBdt)crit\left(\frac{dB}{dt}\right)_{\text{crit}}, required to produce an induced current sufficient for the magnetic force on this wire segment to overcome static friction and initiate slip? (Take g=9.80 m/s2g = 9.80\text{ m/s}^2).

Answer and steps

Final answer

(dBdt)crit=2.45 T/s\left(\frac{dB}{dt}\right)_{\text{crit}} = 2.45\text{ T/s}

Steps

01

Find the induced emf and current

To find the critical rate of change of the primary magnetic field, (dBdt)crit\left(\frac{dB}{dt}\right)_{\text{crit}}, we determine the induced electromotive force (emf), the resulting current in the loop, and the horizontal magnetic force required to overcome static friction.

According to Faraday's law of electromagnetic induction, the magnitude of the induced emf E\mathcal{E} in a single-turn loop is given by the time rate of change of magnetic flux ΦB\Phi_B: E=∣dΦBdt∣\mathcal{E} = \left|\frac{d\Phi_B}{dt}\right|

Since the primary vertical magnetic field is uniform over the square frame of side length LL, the magnetic flux through the loop of area A=L2A = L^2 is: ΦB=BA=BL2\Phi_B = B A = B L^2

Differentiating with respect to time gives: E=L2dBdt\mathcal{E} = L^2 \frac{dB}{dt}

Using Ohm's law, the induced current circulating through the frame with total resistance RR is: I=ER=L2RdBdtI = \frac{\mathcal{E}}{R} = \frac{L^2}{R} \frac{dB}{dt}


02

Relate the magnetic force to static friction

The localized magnetic field BextB_{\text{ext}} exerts a magnetic force of magnitude FBF_B on the wire segment of length LL: FB=ILBextF_B = I L B_{\text{ext}}

Substitute the expression for current II: FB=(L2RdBdt)LBext=L3BextRdBdtF_B = \left(\frac{L^2}{R} \frac{dB}{dt}\right) L B_{\text{ext}} = \frac{L^3 B_{\text{ext}}}{R} \frac{dB}{dt}

For the frame to initiate slip across the tabletop, this driving horizontal magnetic force must just exceed the maximum force of static friction fs,maxf_{s,\text{max}}: fs,max=μsN=μsmgf_{s,\text{max}} = \mu_s N = \mu_s m g

Setting FB=fs,maxF_B = f_{s,\text{max}} at the critical threshold: L3BextR(dBdt)crit=μsmg\frac{L^3 B_{\text{ext}}}{R} \left(\frac{dB}{dt}\right)_{\text{crit}} = \mu_s m g


03

Solve for (dBdt)crit\left(\frac{dB}{dt}\right)_{\text{crit}}

Rearranging the expression yields: (dBdt)crit=μsmgRL3Bext\left(\frac{dB}{dt}\right)_{\text{crit}} = \frac{\mu_s m g R}{L^3 B_{\text{ext}}}

Substitute the given numerical values:

  • L=0.30 m  ⟹  L3=(0.30 m)3=0.027 m3L = 0.30\text{ m} \implies L^3 = (0.30\text{ m})^3 = 0.027\text{ m}^3
  • m=0.045 kgm = 0.045\text{ kg}
  • R=0.25 ΩR = 0.25\ \Omega
  • μs=0.30\mu_s = 0.30
  • Bext=0.50 TB_{\text{ext}} = 0.50\text{ T}
  • g=9.80 m/s2g = 9.80\text{ m/s}^2

fs,max=0.30⋅0.045 kg⋅9.80 m/s2=0.1323 Nf_{s,\text{max}} = 0.30 \cdot 0.045\text{ kg} \cdot 9.80\text{ m/s}^2 = 0.1323\text{ N}

(dBdt)crit=0.1323 N⋅0.25 Ω0.027 m3⋅0.50 T=0.0330750.0135=2.45 T/s\left(\frac{dB}{dt}\right)_{\text{crit}} = \frac{0.1323\text{ N} \cdot 0.25\ \Omega}{0.027\text{ m}^3 \cdot 0.50\text{ T}} = \frac{0.033075}{0.0135} = 2.45\text{ T/s}

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student confuses the side length L with the loop area A, mistakenly setting A = L instead of A = L² when applying Faraday's law.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    fs=μs∗m∗g=0.30∗0.045∗9.80=0.1323 Nf_s = \mu_s * m * g = 0.30 * 0.045 * 9.80 = 0.1323\text{ N}

  2. Step 2

    FB=I∗L∗Bext=fs  ⟹  I=0.13230.30∗0.50=0.882 AF_B = I * L * B_{\text{ext}} = f_s \implies I = \frac{0.1323}{0.30 * 0.50} = 0.882\text{ A}

  3. Step 3

    E=I∗R=0.882∗0.25=0.2205 V\mathcal{E} = I * R = 0.882 * 0.25 = 0.2205\text{ V}

  4. Step 4

    E=A∗(dBdt)=L∗(dBdt)\mathcal{E} = A * \left(\frac{dB}{dt}\right) = L * \left(\frac{dB}{dt}\right)

    Correct

    E=AdBdt=L2dBdt=(0.30 m)2dBdt=0.090 m2⋅dBdt\mathcal{E} = A \frac{dB}{dt} = L^2 \frac{dB}{dt} = (0.30\text{ m})^2 \frac{dB}{dt} = 0.090\text{ m}^2 \cdot \frac{dB}{dt}

    You set the loop area AA equal to the side length LL instead of L2L^2. For a square loop of side length LL, the enclosed surface area is A=L2A = L^2.

  5. Step 5

    (dBdt)crit=0.22050.30=0.735 T/s\left(\frac{dB}{dt}\right)_{\text{crit}} = \frac{0.2205}{0.30} = 0.735\text{ T/s}

    Correct

    (dBdt)crit=EA=0.2205 V0.090 m2=2.45 T/s\left(\frac{dB}{dt}\right)_{\text{crit}} = \frac{\mathcal{E}}{A} = \frac{0.2205\text{ V}}{0.090\text{ m}^2} = 2.45\text{ T/s}

    Dividing by the side length L=0.30 mL = 0.30\text{ m} instead of the area A=0.090 m2A = 0.090\text{ m}^2 propagated the error into your final numerical rate of change.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly calculated the maximum static friction force using fs=μsmgf_s = \mu_s m g.

You successfully related the magnetic force on the current-carrying segment to the friction threshold.

You accurately found the required induced electromotive force using Ohm's law.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Dimensional mismatch: equating area to linear length

You wrote A=LA = L instead of A=L2A = L^2 when expanding magnetic flux ΦB=BA\Phi_B = B A for a square loop.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You conflated the linear segment length LL that appears in the magnetic force formula (F=ILBF = I L B) with the two-dimensional surface area AA required in Faraday's law of induction (ΦB=BA\Phi_B = B A).

REASONING PATH
Your ACEpath teacher’s suggested approach
Flux vs. Force Dimensions
  • Magnetic flux depends on enclosed area (A=L2A = L^2 for a square), whereas magnetic force on a straight segment depends on linear wire length (LL).

  • Whenever both Faraday's law and the Laplace force formula appear in the same problem, explicitly write Aloop=L2A_{\text{loop}} = L^2 and Lwire=LL_{\text{wire}} = L with their units before substituting.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. State the magnetic flux through the square loop: ΦB=BA=BL2\Phi_B = B A = B L^2.

  2. Differentiate with respect to time to find the induced emf: E=L2dBdt=(0.30 m)2dBdt=0.090 m2⋅dBdt\mathcal{E} = L^2 \frac{dB}{dt} = (0.30\text{ m})^2 \frac{dB}{dt} = 0.090\text{ m}^2 \cdot \frac{dB}{dt}.

  3. Solve for the critical rate using the known induced emf E=0.2205 V\mathcal{E} = 0.2205\text{ V}: (dBdt)crit=0.2205 V0.090 m2=2.45 T/s\left(\frac{dB}{dt}\right)_{\text{crit}} = \frac{0.2205\text{ V}}{0.090\text{ m}^2} = 2.45\text{ T/s}.

Final answer

(dBdt)crit=2.45 T/s\left(\frac{dB}{dt}\right)_{\text{crit}} = 2.45\text{ T/s}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the distinction between length ([m][\text{m}]) and area ([m2][\text{m}^2]) when formulating magnetic flux.

  • Check units at each intermediate equation: note that dividing V\text{V} by m\text{m} gives electric field (V/m\text{V/m}), whereas dividing V\text{V} by m2\text{m}^2 gives T/s\text{T/s}.

OverviewACEpath Teacher's Diagnosis

02 The student considers only the mass of the single wire segment rather than the entire frame when calculating the normal and static friction forces.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    msegment=m4=0.0454=0.01125 kg  ⟹  fs=μs⋅msegment⋅g=0.30⋅0.01125⋅9.80=0.033075 Nm_{\text{segment}} = \frac{m}{4} = \frac{0.045}{4} = 0.01125\text{ kg} \implies f_s = \mu_s \cdot m_{\text{segment}} \cdot g = 0.30 \cdot 0.01125 \cdot 9.80 = 0.033075\text{ N}

    Correct

    fs,max=μsmg=0.30⋅0.045 kg⋅9.80 m/s2=0.1323 Nf_{s,\text{max}} = \mu_s m g = 0.30 \cdot 0.045\text{ kg} \cdot 9.80\text{ m/s}^2 = 0.1323\text{ N}

    The entire square wire frame is a single rigid body resting on the table. To initiate slip of the whole frame, the magnetic force acting on the segment must overcome the total static friction of the entire frame, which depends on its full mass m=0.045 kgm = 0.045\text{ kg}, not just one fourth of it.

  2. Step 2

    FB=I⋅L⋅Bext=fs  ⟹  I=0.0330750.30⋅0.50=0.2205 AF_B = I \cdot L \cdot B_{\text{ext}} = f_s \implies I = \frac{0.033075}{0.30 \cdot 0.50} = 0.2205\text{ A}

    Correct

    I=fs,maxLBext=0.1323 N0.30 m⋅0.50 T=0.882 AI = \frac{f_{s,\text{max}}}{L B_{\text{ext}}} = \frac{0.1323\text{ N}}{0.30\text{ m} \cdot 0.50\text{ T}} = 0.882\text{ A}

    Your relationship FB=ILBext=fsF_B = I L B_{\text{ext}} = f_s is conceptually correct, but the numerical value of current is lower by a factor of 4 due to the friction force from Step 1.

  3. Step 3

    E=I⋅R=0.2205⋅0.25=0.055125 V\mathcal{E} = I \cdot R = 0.2205 \cdot 0.25 = 0.055125\text{ V}

    Correct

    E=IR=0.882 A⋅0.25 Ω=0.2205 V\mathcal{E} = I R = 0.882\text{ A} \cdot 0.25\ \Omega = 0.2205\text{ V}

    You applied Ohm's law correctly, but the result is scaled down by the propagated current error.

  4. Step 4

    (dBdt)crit=EL2=0.0551250.090=0.6125 T/s\left(\frac{dB}{dt}\right)_{\text{crit}} = \frac{\mathcal{E}}{L^2} = \frac{0.055125}{0.090} = 0.6125\text{ T/s}

    Correct

    (dBdt)crit=EL2=0.2205 V(0.30 m)2=2.45 T/s\left(\frac{dB}{dt}\right)_{\text{crit}} = \frac{\mathcal{E}}{L^2} = \frac{0.2205\text{ V}}{(0.30\text{ m})^2} = 2.45\text{ T/s}

    You correctly related the induced electromotive force to Faraday's law using E=L2dBdt\mathcal{E} = L^2 \frac{dB}{dt}, but the final rate inherits the factor-of-4 error from Step 1.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified the magnetic force formula on a current-carrying wire as FB=ILBextF_B = I L B_{\text{ext}}.

You accurately linked induced current to electromotive force using Ohm's law, E=IR\mathcal{E} = I R.

You correctly applied Faraday's law for a square loop to relate the rate of change of magnetic field to induced emf via E=L2dBdt\mathcal{E} = L^2 \frac{dB}{dt}.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Partial System Mass in Friction

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You isolated the single wire segment where the magnetic force is applied and computed the normal force using only that segment's mass (m/4m/4), forgetting that the entire connected frame must slide as one rigid body against the tabletop.

REASONING PATH
Your ACEpath teacher’s suggested approach
Define the System Boundary for Newton's Laws
  • For a connected rigid structure sliding along a surface, the total normal force is N=mtotalgN = m_{\text{total}} g.

  • Whenever a force acts on one part of a rigid object, check whether the entire object moves together before calculating normal force and maximum static friction.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Calculate the maximum static friction for the entire frame: fs,max=μsmg=0.30⋅0.045 kg⋅9.80 m/s2=0.1323 Nf_{s,\text{max}} = \mu_s m g = 0.30 \cdot 0.045\text{ kg} \cdot 9.80\text{ m/s}^2 = 0.1323\text{ N}.

  2. Find the required induced current: I=fs,maxLBext=0.13230.30⋅0.50=0.882 AI = \frac{f_{s,\text{max}}}{L B_{\text{ext}}} = \frac{0.1323}{0.30 \cdot 0.50} = 0.882\text{ A}.

  3. Find the required induced emf: E=IR=0.882 A⋅0.25 Ω=0.2205 V\mathcal{E} = I R = 0.882\text{ A} \cdot 0.25\ \Omega = 0.2205\text{ V}.

  4. Solve for the critical field rate: (dBdt)crit=EL2=0.2205 V(0.30 m)2=2.45 T/s\left(\frac{dB}{dt}\right)_{\text{crit}} = \frac{\mathcal{E}}{L^2} = \frac{0.2205\text{ V}}{(0.30\text{ m})^2} = 2.45\text{ T/s}.

Final answer

(dBdt)crit=2.45 T/s\left(\frac{dB}{dt}\right)_{\text{crit}} = 2.45\text{ T/s}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review free-body diagrams for rigid multi-part frames to confirm whether motion involves individual parts or the entire structure.

  • Practice problems where local driving forces (like localized Lorentz forces or tension) must overcome friction distributed across a whole body.

OverviewACEpath Teacher's Diagnosis

03 The student mistakenly uses the local external magnetic field B_ext instead of the changing primary field rate in Faraday's law, confusing the field that generates the emf with the field that exerts the deflecting force.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    fs=μs⋅m⋅g=0.1323 Nf_s = \mu_s \cdot m \cdot g = 0.1323\text{ N}

  2. Step 2

    FB=I⋅L⋅(dBdt)=fsF_B = I \cdot L \cdot \left(\frac{dB}{dt}\right) = f_s

    Correct

    FB=ILBext=fs,maxF_B = I L B_{\text{ext}} = f_{s,\text{max}}

    In this line, you wrote the magnetic force as IL(dBdt)I L \left(\frac{dB}{dt}\right) instead of ILBextI L B_{\text{ext}}. Magnetic force depends directly on the magnetic field BB, whereas dBdt\frac{dB}{dt} has units of T/s\text{T/s} and determines the induced emf, not the Lorentz force directly.

  3. Step 3

    E=L2⋅(dBdt)  ⟹  I=ER=L2⋅(dB/dt)R\mathcal{E} = L^2 \cdot \left(\frac{dB}{dt}\right) \implies I = \frac{\mathcal{E}}{R} = \frac{L^2 \cdot (dB/dt)}{R}

  4. Step 4

    FB=[L2⋅(dB/dt)R]⋅L⋅Bext=fsF_B = \left[\frac{L^2 \cdot (dB/dt)}{R}\right] \cdot L \cdot B_{\text{ext}} = f_s

  5. Step 5

    (dBdt)crit=fs⋅RL3⋅Bext=0.1323⋅0.250.027⋅0.50=2.45 T/s\left(\frac{dB}{dt}\right)_{\text{crit}} = \frac{f_s \cdot R}{L^3 \cdot B_{\text{ext}}} = \frac{0.1323 \cdot 0.25}{0.027 \cdot 0.50} = 2.45\text{ T/s}

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly calculated the threshold static friction force from the normal force and coefficient of friction.

You correctly applied Faraday's law to relate the time-varying primary magnetic field to the induced electromotive force.

You correctly used Ohm's law and the Laplace magnetic force formula to set up the final force balance and solve for the critical rate.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Field rate vs. field strength confusion in magnetic force

You initially wrote FB=IL(dB/dt)F_B = I L (dB/dt) before replacing it with the correct formula FB=ILBextF_B = I L B_{\text{ext}} in your later steps.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Momentary confusion between the time derivative of the magnetic field dBdt\frac{dB}{dt} (which induces the electric field driving the current) and the static magnetic field BB (which exerts the deflecting Lorentz force on a current-carrying wire).

REASONING PATH
Your ACEpath teacher’s suggested approach
Separating Field Roles
  • Changing flux dΦBdt=AdBdt\frac{d\Phi_B}{dt} = A \frac{dB}{dt} induces the emf E\mathcal{E}, while the magnetic field itself BB exerts the force F=ILBF = I L B.

  • Whenever two magnetic field quantities appear, label them explicitly by their roles: Binduce(t)B_{\text{induce}}(t) for induction and BforceB_{\text{force}} for deflection.

Dimensional Consistency
  • [FB]=N=A⋅m⋅T[F_B] = \text{N} = \text{A} \cdot \text{m} \cdot \text{T}.

  • Check that any magnetic force expression contains field strength in teslas (T\text{T}), not field rate of change in teslas per second (T/s\text{T/s}).

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Find the induced electromotive force from Faraday's law: E=AdBdt=L2dBdt\mathcal{E} = A \frac{dB}{dt} = L^2 \frac{dB}{dt}.

  2. Find the induced current via Ohm's law: I=ER=L2RdBdtI = \frac{\mathcal{E}}{R} = \frac{L^2}{R} \frac{dB}{dt}.

  3. Set the horizontal magnetic force equal to static friction: FB=ILBext=fs,maxF_B = I L B_{\text{ext}} = f_{s,\text{max}}.

  4. Substitute II and solve: (dBdt)crit=μsmgRL3Bext=2.45 T/s\left(\frac{dB}{dt}\right)_{\text{crit}} = \frac{\mu_s m g R}{L^3 B_{\text{ext}}} = 2.45\text{ T/s}.

Final answer

(dBdt)crit=2.45 T/s\left(\frac{dB}{dt}\right)_{\text{crit}} = 2.45\text{ T/s}

NEXT STEPS
Final Takeaways from Your Teacher
  • Cross out preliminary scratch lines so graders know they do not represent your final reasoning.

  • Perform a quick unit check whenever you write a force formula: ensure T\text{T} appears rather than T/s\text{T/s}.

Lock it in

Similar question

01

A square loop of side length 0.20 m0.20\text{ m} and resistance 0.50 Ω0.50\ \Omega lies in a perpendicular magnetic field. If the magnetic field increases at a uniform rate of 4.0 T/s4.0\text{ T/s}, what is the induced current in the loop?

Answer

I=0.32 AI = 0.32\text{ A}. First compute area A=(0.20 m)2=0.040 m2A = (0.20\text{ m})^2 = 0.040\text{ m}^2. The induced emf is E=AdBdt=0.040⋅4.0=0.16 V\mathcal{E} = A \frac{dB}{dt} = 0.040 \cdot 4.0 = 0.16\text{ V}. Then by Ohm's law, I=ER=0.160.50=0.32 AI = \frac{\mathcal{E}}{R} = \frac{0.16}{0.50} = 0.32\text{ A}.

02

An equilateral triangular wire frame with side length a=0.40 ma = 0.40\text{ m} and total resistance R=0.80 ΩR = 0.80\ \Omega lies flat in a perpendicular changing field. If the induced current is measured to be 0.15 A0.15\text{ A}, find the rate of change of the magnetic field dBdt\frac{dB}{dt}.

Answer

dBdt≈1.73 T/s\frac{dB}{dt} \approx 1.73\text{ T/s}. The area of an equilateral triangle is A=34a2=34(0.40)2≈0.06928 m2A = \frac{\sqrt{3}}{4} a^2 = \frac{\sqrt{3}}{4} (0.40)^2 \approx 0.06928\text{ m}^2. The required emf is E=IR=0.15⋅0.80=0.12 V\mathcal{E} = I R = 0.15 \cdot 0.80 = 0.12\text{ V}. Thus, dBdt=EA=0.120.06928≈1.73 T/s\frac{dB}{dt} = \frac{\mathcal{E}}{A} = \frac{0.12}{0.06928} \approx 1.73\text{ T/s}.

03

A rectangular wire loop with dimensions 0.10 m×0.20 m0.10\text{ m} \times 0.20\text{ m}, mass 0.020 kg0.020\text{ kg}, and resistance 0.10 Ω0.10\ \Omega rests on a table (μs=0.25\mu_s = 0.25, g=9.8 m/s2g = 9.8\text{ m/s}^2). A perpendicular primary field increases at dBdt\frac{dB}{dt}. One of the short sides (0.10 m0.10\text{ m}) is exposed to a transverse external field Bext=0.40 TB_{\text{ext}} = 0.40\text{ T}. Calculate the critical rate (dBdt)crit\left(\frac{dB}{dt}\right)_{\text{crit}} to cause slipping.

Answer

(dBdt)crit≈6.13 T/s\left(\frac{dB}{dt}\right)_{\text{crit}} \approx 6.13\text{ T/s}. The maximum static friction is fs=μsmg=0.25⋅0.020⋅9.8=0.049 Nf_s = \mu_s m g = 0.25 \cdot 0.020 \cdot 9.8 = 0.049\text{ N}. Setting FB=ILsideBext=fsF_B = I L_{\text{side}} B_{\text{ext}} = f_s gives I=0.0490.10⋅0.40=1.225 AI = \frac{0.049}{0.10 \cdot 0.40} = 1.225\text{ A}. The required emf is E=IR=1.225⋅0.10=0.1225 V\mathcal{E} = I R = 1.225 \cdot 0.10 = 0.1225\text{ V}. The loop area is A=0.10×0.20=0.020 m2A = 0.10 \times 0.20 = 0.020\text{ m}^2. Therefore, (dBdt)crit=EA=0.12250.020=6.125 T/s≈6.13 T/s\left(\frac{dB}{dt}\right)_{\text{crit}} = \frac{\mathcal{E}}{A} = \frac{0.1225}{0.020} = 6.125\text{ T/s} \approx 6.13\text{ T/s}.

Loading workspace…