Resources

A roller-coaster car of mass m=450 kgm = 450\text{ kg} is released from rest at the top of an initial hill at height h1=32.0 mh_1 = 32.0\text{ m} above ground level. It travels down a frictionless track and enters a circular vertical loop-the-loop of radius R=8.00 mR = 8.00\text{ m}. Assuming air resistance and track friction are completely negligible, and using g=9.80 m/s2g = 9.80\text{ m/s}^2, determine the speed vtopv_{\text{top}} of the car when it reaches the very top of the circular loop.

Answer and steps

Final answer

vtop=17.7 m/sv_{\text{top}} = 17.7\text{ m/s}

Steps

01

Identify the Relevant Principle

Because friction and air resistance are negligible, the only force doing work on the car is gravity, which is a conservative force. Therefore, the total mechanical energy of the system is conserved throughout the motion:

Einitial=EfinalE_{\text{initial}} = E_{\text{final}}

02

Determine the Heights and Energy Expressions

Let ground level be the reference level where gravitational potential energy is zero (y=0y = 0).

  • Initial State (Release from rest at the top of the hill):

    • Height: h1=32.0 mh_1 = 32.0\text{ m}
    • Speed: v1=0 m/sv_1 = 0\text{ m/s}
    • Total mechanical energy: E1=U1+K1=mgh1+0=mgh1E_1 = U_1 + K_1 = mgh_1 + 0 = mgh_1
  • Final State (At the top of the vertical loop):

    • The loop is circular with radius R=8.00 mR = 8.00\text{ m}. The top of the loop is at a height equal to the loop's diameter: htop=2R=2(8.00 m)=16.0 mh_{\text{top}} = 2R = 2(8.00\text{ m}) = 16.0\text{ m}
    • Speed: vtopv_{\text{top}}
    • Total mechanical energy: Etop=Utop+Ktop=mg(2R)+12mvtop2E_{\text{top}} = U_{\text{top}} + K_{\text{top}} = mg(2R) + \frac{1}{2}mv_{\text{top}}^2

Common Pitfall: Do not confuse the radius of the loop with its height. The top of the loop is at height 2R2R above the bottom of the loop (ground level), not RR.

03

Apply Conservation of Energy

Equate the total mechanical energy at the release point to that at the top of the loop:

mgh1=mg(2R)+12mvtop2mgh_1 = mg(2R) + \frac{1}{2}mv_{\text{top}}^2

Notice that the mass mm appears in every term, so it cancels out:

gh1=2gR+12vtop2gh_1 = 2gR + \frac{1}{2}v_{\text{top}}^2

04

Solve for vtopv_{\text{top}}

Rearrange the equation to isolate vtop2v_{\text{top}}^2:

12vtop2=g(h1−2R)\frac{1}{2}v_{\text{top}}^2 = g(h_1 - 2R)

vtop2=2g(h1−2R)v_{\text{top}}^2 = 2g(h_1 - 2R)

Substitute the given numerical values:

h1−2R=32.0 m−16.0 m=16.0 mh_1 - 2R = 32.0\text{ m} - 16.0\text{ m} = 16.0\text{ m}

vtop2=2(9.80 m/s2)(16.0 m)=313.6 m2/s2v_{\text{top}}^2 = 2(9.80\text{ m/s}^2)(16.0\text{ m}) = 313.6\text{ m}^2/\text{s}^2

Take the square root:

vtop=313.6 m2/s2≈17.7 m/sv_{\text{top}} = \sqrt{313.6\text{ m}^2/\text{s}^2} \approx 17.7\text{ m/s}

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student confuses the height of the top of the loop with its radius instead of its diameter, using h = R = 8.00 m instead of 2R = 16.0 m.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    Einitial=Etop  ⟹  mgh1=mgR+12mvtop2E_{\text{initial}} = E_{\text{top}} \implies mgh_1 = mgR + \frac{1}{2}mv_{\text{top}}^2

    Correct

    Einitial=Etop  ⟹  mgh1=mg(2R)+12mvtop2E_{\text{initial}} = E_{\text{top}} \implies mgh_1 = mg(2R) + \frac{1}{2}mv_{\text{top}}^2

    You set the gravitational potential energy at the top of the loop to mgRmgR. Because the circular loop rests on the ground (y=0y = 0), its top is at a height equal to the diameter of the circle, htop=2R=16.0 mh_{\text{top}} = 2R = 16.0\text{ m}, not the radius RR.

  2. Step 2

    gh1−gR=12vtop2  ⟹  vtop2=2g(h1−R)gh_1 - gR = \frac{1}{2}v_{\text{top}}^2 \implies v_{\text{top}}^2 = 2g(h_1 - R)

    Correct

    gh1−2gR=12vtop2  ⟹  vtop2=2g(h1−2R)gh_1 - 2gR = \frac{1}{2}v_{\text{top}}^2 \implies v_{\text{top}}^2 = 2g(h_1 - 2R)

    You correctly isolated vtop2v_{\text{top}}^2 algebraically from your equation in Step 1, but the expression carries forward the missing factor of 22 on the radius.

  3. Step 3

    vtop2=2(9.80)(32.0−8.00)=470.4v_{\text{top}}^2 = 2(9.80)(32.0 - 8.00) = 470.4

    Correct

    vtop2=2(9.80)(32.0−16.0)=313.6v_{\text{top}}^2 = 2(9.80)(32.0 - 16.0) = 313.6

    You substituted the values and computed the product accurately according to your formula, but the height subtracted should be 2R=16.0 m2R = 16.0\text{ m} rather than 8.00 m8.00\text{ m}.

  4. Step 4

    vtop=470.4≈21.7 m/sv_{\text{top}} = \sqrt{470.4} \approx 21.7\text{ m/s}

    Correct

    vtop=313.6≈17.7 m/sv_{\text{top}} = \sqrt{313.6} \approx 17.7\text{ m/s}

    You evaluated the square root correctly, but the resulting numerical value is affected by the earlier height error.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly recognized that total mechanical energy is conserved throughout the frictionless motion.

You accurately cancelled the mass mm from both sides of the energy conservation equation.

You demonstrated solid algebraic manipulation and precise arithmetic calculations.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Radius vs. Diameter in Vertical Loop

Using the loop's radius RR as the height of the top of the loop rather than its diameter 2R2R.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You associated the vertical dimension of the circle with its radius RR, forgetting that moving from the bottom of a circle on the ground to its highest point spans the full vertical diameter (h=2Rh = 2R).

REASONING PATH
Your ACEpath teacher’s suggested approach
Reference Height of a Vertical Loop
  • For a vertical circle of radius RR resting at ground level (y=0y = 0), the bottom is at y=0y = 0, the center is at y=Ry = R, and the top is at y=2Ry = 2R.

  • Draw a quick diagram of the loop and mark the heights of key points (00, RR, and 2R2R) relative to your chosen reference level before writing the gravitational potential energy term.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Set the potential energy at the apex using htop=2Rh_{\text{top}} = 2R: mgh1=mg(2R)+12mvtop2mgh_1 = mg(2R) + \frac{1}{2}mv_{\text{top}}^2.

  2. Divide by mass mm and rearrange for vtop2v_{\text{top}}^2: vtop2=2g(h1−2R)v_{\text{top}}^2 = 2g(h_1 - 2R).

  3. Substitute the numerical values: vtop2=2(9.80 m/s2)(32.0 m−16.0 m)=313.6 m2/s2v_{\text{top}}^2 = 2(9.80\text{ m/s}^2)(32.0\text{ m} - 16.0\text{ m}) = 313.6\text{ m}^2/\text{s}^2.

  4. Take the square root: vtop=313.6 m2/s2≈17.7 m/sv_{\text{top}} = \sqrt{313.6\text{ m}^2/\text{s}^2} \approx 17.7\text{ m/s}.

Final answer

vtop=17.7 m/sv_{\text{top}} = 17.7\text{ m/s}

NEXT STEPS
Final Takeaways from Your Teacher
  • Double-check geometric heights when applying potential energy U=mghU = mgh: always verify whether a given dimension is a radius (RR) or a total vertical displacement (2R2R).

  • Label reference heights (y=0y = 0, y=Ry = R, y=2Ry = 2R) directly on your sketch before substituting into energy conservation equations.

OverviewACEpath Teacher's Diagnosis

02 The student omits the factor of 1/2 in the kinetic energy formula, writing KE = m v².

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    htop=2R=2(8.00)=16.0 mh_{\text{top}} = 2R = 2(8.00) = 16.0\text{ m}

  2. Step 2

    mgh1=mghtop+mvtop2mgh_1 = mgh_{\text{top}} + mv_{\text{top}}^2

    Correct

    mgh1=mghtop+12mvtop2mgh_1 = mgh_{\text{top}} + \frac{1}{2}mv_{\text{top}}^2

    Translational kinetic energy is defined as K=12mv2K = \frac{1}{2}mv^2. You wrote mvtop2mv_{\text{top}}^2, missing the factor of 12\frac{1}{2}.

  3. Step 3

    g(h1−htop)=vtop2  ⟹  vtop2=9.80(32.0−16.0)=156.8  ⟹  vtop=156.8≈12.5 m/sg(h_1 - h_{\text{top}}) = v_{\text{top}}^2 \implies v_{\text{top}}^2 = 9.80(32.0 - 16.0) = 156.8 \implies v_{\text{top}} = \sqrt{156.8} \approx 12.5\text{ m/s}

    Correct

    vtop2=2g(h1−htop)=2(9.80)(16.0)=313.6 m2/s2  ⟹  vtop≈17.7 m/sv_{\text{top}}^2 = 2g(h_1 - h_{\text{top}}) = 2(9.80)(16.0) = 313.6\text{ m}^2/\text{s}^2 \implies v_{\text{top}} \approx 17.7\text{ m/s}

    Your algebra and arithmetic were executed cleanly based on your equation, but the final numerical value was affected by the missing 12\frac{1}{2} coefficient.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified that the top of the circular loop is at a height of 2R2R above ground level.

You recognized that mechanical energy is conserved and equated the initial potential energy to the sum of potential and kinetic energy at the peak.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Omitted factor of 1/2 in kinetic energy

You wrote the kinetic energy term as mv2mv^2 rather than 12mv2\frac{1}{2}mv^2.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

A quick formula slip when writing mechanical energy conservation, conflating kinetic energy K=12mv2K = \frac{1}{2}mv^2 with mv2mv^2.

REASONING PATH
Your ACEpath teacher’s suggested approach
Kinetic Energy Formula
  • Translational kinetic energy is always K=12mv2K = \frac{1}{2}mv^2, never mv2mv^2.

  • Whenever you write an energy balance equation, verify each kinetic energy term has its leading factor of 12\frac{1}{2} before canceling mass.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. mgh1=mghtop+12mvtop2mgh_1 = mgh_{\text{top}} + \frac{1}{2}mv_{\text{top}}^2

  2. Cancel mass mm and isolate vtop2v_{\text{top}}^2: 12vtop2=g(h1−htop)  ⟹  vtop2=2g(h1−htop)\frac{1}{2}v_{\text{top}}^2 = g(h_1 - h_{\text{top}}) \implies v_{\text{top}}^2 = 2g(h_1 - h_{\text{top}})

  3. Substitute numerical values: vtop2=2(9.80 m/s2)(32.0 m−16.0 m)=313.6 m2/s2v_{\text{top}}^2 = 2(9.80\text{ m/s}^2)(32.0\text{ m} - 16.0\text{ m}) = 313.6\text{ m}^2/\text{s}^2

  4. Take the square root: vtop=313.6 m2/s2≈17.7 m/sv_{\text{top}} = \sqrt{313.6\text{ m}^2/\text{s}^2} \approx 17.7\text{ m/s}

Final answer

vtop=17.7 m/sv_{\text{top}} = 17.7\text{ m/s}

NEXT STEPS
Final Takeaways from Your Teacher
  • Double-check your standard energy equations during the setup phase: K=12mv2K = \frac{1}{2}mv^2 and U=mghU = mgh.

  • Practice solving conservation of energy problems by isolating the unknown speed algebraically before substituting numbers.

OverviewACEpath Teacher's Diagnosis

03 The student calculates the velocity assuming the entire initial potential energy converts to kinetic energy, completely ignoring the gravitational potential energy at the top of the loop.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    mgh1=12mvtop2m g h_1 = \frac{1}{2} m v_{\text{top}}^2

    Correct

    mgh1=mg(2R)+12mvtop2m g h_1 = m g (2R) + \frac{1}{2} m v_{\text{top}}^2

    The car reaches the top of a circular loop of radius R=8.00 mR = 8.00\text{ m}, which is at height htop=2R=16.0 mh_{\text{top}} = 2R = 16.0\text{ m} above the ground. Because the car is still elevated, its final mechanical energy must include both gravitational potential energy mg(2R)m g (2R) and kinetic energy 12mvtop2\frac{1}{2} m v_{\text{top}}^2.

  2. Step 2

    vtop2=2gh1  ⟹  vtop2=2(9.80)(32.0)=627.2v_{\text{top}}^2 = 2 g h_1 \implies v_{\text{top}}^2 = 2(9.80)(32.0) = 627.2

    Correct

    vtop2=2g(h1−2R)=2(9.80)(32.0−16.0)=313.6v_{\text{top}}^2 = 2g(h_1 - 2R) = 2(9.80)(32.0 - 16.0) = 313.6

    Your algebraic rearrangement and numerical substitution were executed correctly, but they propagated the missing potential energy term from the setup.

  3. Step 3

    vtop=627.2≈25.0 m/sv_{\text{top}} = \sqrt{627.2} \approx 25.0\text{ m/s}

    Correct

    vtop=313.6≈17.7 m/sv_{\text{top}} = \sqrt{313.6} \approx 17.7\text{ m/s}

    Your square root evaluation was calculated correctly for your expression, but the resulting speed represents the car reaching ground level (h=0h=0) rather than the top of the loop.

WHAT YOU DID WELL
Compliments from Your Teacher

You recognized that total mechanical energy is conserved throughout the frictionless motion.

You correctly formulated the initial mechanical energy as pure gravitational potential energy mgh1m g h_1.

You carried out the algebraic solving and arithmetic accurately based on your initial equation.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Missing Final Potential Energy

Equating the initial potential energy entirely to kinetic energy at an elevated position.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You assumed all initial potential energy converted to kinetic energy, overlooking that the top of a circular loop of radius RR is at height h=2Rh = 2R above ground level and still retains gravitational potential energy.

REASONING PATH
Your ACEpath teacher’s suggested approach
Height Check at Every State
  • At any position of height hh above the chosen reference line (y=0y = 0), an object of mass mm has gravitational potential energy U=mghU = mgh.

  • Before equating initial and final energies, list the height hh and speed vv for both points explicitly so no potential energy terms are omitted.

Loop Geometry Reminder
  • The top of a vertical circular loop sitting on the ground is located at height h=2Rh = 2R (the diameter), not RR and not 00.

  • Sketch the loop and label the ground level (y=0y = 0), the center (y=Ry = R), and the peak (y=2Ry = 2R) before writing the energy equation.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Write the conservation of mechanical energy equation including both potential and kinetic energy at the top of the loop: mgh1=mg(2R)+12mvtop2mgh_1 = mg(2R) + \frac{1}{2}mv_{\text{top}}^2.

  2. Divide through by mass mm and isolate vtop2v_{\text{top}}^2: vtop2=2g(h1−2R)v_{\text{top}}^2 = 2g(h_1 - 2R).

  3. Substitute the known values h1=32.0 mh_1 = 32.0\text{ m}, R=8.00 mR = 8.00\text{ m}, and g=9.80 m/s2g = 9.80\text{ m/s}^2: vtop2=2(9.80)(32.0−16.0)=313.6 m2/s2v_{\text{top}}^2 = 2(9.80)(32.0 - 16.0) = 313.6\text{ m}^2/\text{s}^2.

  4. Take the square root: vtop=313.6≈17.7 m/sv_{\text{top}} = \sqrt{313.6} \approx 17.7\text{ m/s}.

Final answer

vtop=17.7 m/sv_{\text{top}} = 17.7\text{ m/s}

NEXT STEPS
Final Takeaways from Your Teacher
  • When applying conservation of mechanical energy, always write the full template Ui+Ki=Uf+KfU_i + K_i = U_f + K_f before canceling or setting terms to zero.

  • Double-check whether the final location is at ground level or still elevated above your reference line.

Lock it in

Similar question

01

A frictionless roller-coaster car is released from rest at a height of h1=25.0 mh_1 = 25.0\text{ m} above the ground. It enters a circular vertical loop of radius R=5.00 mR = 5.00\text{ m} whose bottom rests at ground level. Using g=9.80 m/s2g = 9.80\text{ m/s}^2, find the speed of the car at the top of the loop.

Answer

v=17.1 m/sv = 17.1\text{ m/s}. The height at the top of the loop is htop=2R=2(5.00 m)=10.0 mh_{\text{top}} = 2R = 2(5.00\text{ m}) = 10.0\text{ m}. By conservation of mechanical energy, mgh1=mg(2R)+12mv2  ⟹  v=2g(h1−2R)=2(9.80)(25.0−10.0)=294≈17.1 m/smgh_1 = mg(2R) + \frac{1}{2}mv^2 \implies v = \sqrt{2g(h_1 - 2R)} = \sqrt{2(9.80)(25.0 - 10.0)} = \sqrt{294} \approx 17.1\text{ m/s}.

02

A roller-coaster car is released from rest from a hill of height hh above the ground and moves along a frictionless track with a vertical circular loop of radius R=6.00 mR = 6.00\text{ m}. To maintain contact with the track at the very top of the loop, the car must have a minimum speed of vtop=gRv_{\text{top}} = \sqrt{gR}. What is the minimum release height hminh_{\text{min}} above the ground?

Answer

hmin=15.0 mh_{\text{min}} = 15.0\text{ m}. By conservation of energy, mghmin=mg(2R)+12mvtop2mgh_{\text{min}} = mg(2R) + \frac{1}{2}m v_{\text{top}}^2. Substituting vtop2=gRv_{\text{top}}^2 = gR yields ghmin=2gR+12gR=2.5gR  ⟹  hmin=2.5R=2.5(6.00 m)=15.0 mgh_{\text{min}} = 2gR + \frac{1}{2}gR = 2.5gR \implies h_{\text{min}} = 2.5R = 2.5(6.00\text{ m}) = 15.0\text{ m}.

03

A coaster car enters a vertical circular loop of radius R=10.0 mR = 10.0\text{ m} at ground level with an initial speed v0=24.0 m/sv_0 = 24.0\text{ m/s}. Assuming negligible friction and taking g=9.80 m/s2g = 9.80\text{ m/s}^2, calculate its speed at the top of the loop, and find the normal force exerted by the track on a 400 kg400\text{ kg} passenger at the top.

Answer

vtop≈13.6 m/sv_{\text{top}} \approx 13.6\text{ m/s} and FN≈3.44×103 NF_N \approx 3.44 \times 10^3\text{ N}. (1) Energy conservation from ground (y=0y=0) to loop top (y=2R=20.0 my = 2R = 20.0\text{ m}): 12mv02=mg(2R)+12mvtop2  ⟹  vtop2=v02−4gR=(24.0)2−4(9.80)(10.0)=576−392=184 m2/s2\frac{1}{2}mv_0^2 = mg(2R) + \frac{1}{2}mv_{\text{top}}^2 \implies v_{\text{top}}^2 = v_0^2 - 4gR = (24.0)^2 - 4(9.80)(10.0) = 576 - 392 = 184\text{ m}^2/\text{s}^2, so vtop=184≈13.6 m/sv_{\text{top}} = \sqrt{184} \approx 13.6\text{ m/s}. (2) At the top, gravity and normal force both point downward toward the center: FN+mg=mvtop2R  ⟹  FN=m(vtop2R−g)=400(18410.0−9.80)=400(8.60)=3440 NF_N + mg = \frac{mv_{\text{top}}^2}{R} \implies F_N = m\left(\frac{v_{\text{top}}^2}{R} - g\right) = 400\left(\frac{184}{10.0} - 9.80\right) = 400(8.60) = 3440\text{ N}.

Loading workspace…