Resources

An upright, unconstrained solid column of original height H0H_0, uniform cross-sectional area AA, Young's modulus EE, and uniform volumetric mass density ρ\rho deforms purely under the asymptotic distribution of its own self-weight under gravitational acceleration gg. (a) By setting up an integral of the local elastic strain d(Δy)/dyd(\Delta y)/dy from the free top (y=H0y = H_0) down to the rigid ground base (y=0y = 0), derive the symbolic expression for the total base-to-top elastic vertical compression ΔHtotal\Delta H_{\text{total}} of the column in terms of ρ\rho, gg, H0H_0, and EE. (b) Evaluate this total compression numerically for a massive concrete pylon of height H0=85.0 mH_0 = 85.0\text{ m}, density ρ=2400 kg/m3\rho = 2400\text{ kg/m}^3, Young's modulus E=3.00×1010 PaE = 3.00 \times 10^{10}\text{ Pa}, and g=9.80 m/s2g = 9.80\text{ m/s}^2.

Answer and steps

Final answer

(a) ΔHtotal=ρgH022E\Delta H_{\text{total}} = \frac{\rho g H_0^2}{2E}; (b) ΔHtotal=2.83×10−3 m=2.83 mm\Delta H_{\text{total}} = 2.83 \times 10^{-3}\text{ m} = 2.83\text{ mm}

Steps

Part (a): Derivation of the Total Vertical Compression

  1. Identify the force acting on an arbitrary slice: Choose a vertical coordinate system where y=0y = 0 is at the rigid base and y=H0y = H_0 is at the free top surface.

    Consider an infinitesimal horizontal slice of original thickness dydy located at height yy. The downward compressive force F(y)F(y) supported by this slice is equal to the weight of the column segment lying directly above it (from height yy to height H0H_0): F(y)=maboveg=ρVaboveg=ρA(H0−y)gF(y) = m_{\text{above}} g = \rho V_{\text{above}} g = \rho A (H_0 - y) g

  2. Determine the local compressive stress and strain:

    • The compressive stress σ(y)\sigma(y) at height yy is: σ(y)=F(y)A=ρg(H0−y)\sigma(y) = \frac{F(y)}{A} = \rho g (H_0 - y)
    • By Hooke's Law for uniaxial deformation, stress and strain are related by Young's modulus EE: σ(y)=Eε(y)\sigma(y) = E \varepsilon(y)
    • Therefore, the local compressive strain ε(y)=d(Δy)dy\varepsilon(y) = \frac{d(\Delta y)}{dy} is: ε(y)=σ(y)E=ρg(H0−y)E\varepsilon(y) = \frac{\sigma(y)}{E} = \frac{\rho g (H_0 - y)}{E}
  3. Integrate to find total vertical compression: The total vertical compression ΔHtotal\Delta H_{\text{total}} is obtained by integrating the local compression d(Δy)=ε(y) dyd(\Delta y) = \varepsilon(y)\,dy over the entire height of the column, from the base (y=0y = 0) to the top (y=H0y = H_0): ΔHtotal=∫0H0ε(y) dy=∫0H0ρg(H0−y)E dy\Delta H_{\text{total}} = \int_{0}^{H_0} \varepsilon(y)\,dy = \int_{0}^{H_0} \frac{\rho g (H_0 - y)}{E}\,dy

    Evaluating the integral: ΔHtotal=ρgE[H0y−y22]0H0=ρgE(H02−H022)=ρgH022E\Delta H_{\text{total}} = \frac{\rho g}{E} \left[ H_0 y - \frac{y^2}{2} \right]_{0}^{H_0} = \frac{\rho g}{E} \left( H_0^2 - \frac{H_0^2}{2} \right) = \frac{\rho g H_0^2}{2E}

    Common Pitfall: Treating the compressive force as constant throughout the column using the total weight Mg=ρAH0gM g = \rho A H_0 g yields ΔH=ρgH02E\Delta H = \frac{\rho g H_0^2}{E}, which overestimates the deformation by a factor of 22. The factor of 1/21/2 naturally arises because the stress varies linearly from zero at the free top to a maximum of ρgH0\rho g H_0 at the base.


Part (b): Numerical Evaluation

Substitute the given numerical parameters into the derived formula:

  • Height, H0=85.0 mH_0 = 85.0\text{ m}
  • Density, ρ=2400 kg/m3\rho = 2400\text{ kg/m}^3
  • Young's modulus, E=3.00×1010 PaE = 3.00 \times 10^{10}\text{ Pa}
  • Acceleration due to gravity, g=9.80 m/s2g = 9.80\text{ m/s}^2

ΔHtotal=(2400 kg/m3)(9.80 m/s2)(85.0 m)22(3.00×1010 Pa)\Delta H_{\text{total}} = \frac{(2400\text{ kg/m}^3)(9.80\text{ m/s}^2)(85.0\text{ m})^2}{2(3.00 \times 10^{10}\text{ Pa})}

Calculate the numerator and denominator:

  • Numerator: 2400⋅9.80⋅(85.0)2=23520⋅7225=1.69932×108 N/m2400 \cdot 9.80 \cdot (85.0)^2 = 23520 \cdot 7225 = 1.69932 \times 10^8\text{ N/m}
  • Denominator: 2⋅(3.00×1010)=6.00×1010 Pa2 \cdot (3.00 \times 10^{10}) = 6.00 \times 10^{10}\text{ Pa}

Divide: ΔHtotal=1.69932×1086.00×1010≈2.8322×10−3 m\Delta H_{\text{total}} = \frac{1.69932 \times 10^8}{6.00 \times 10^{10}} \approx 2.8322 \times 10^{-3}\text{ m}

Expressed to three significant figures: ΔHtotal=2.83×10−3 m=2.83 mm\Delta H_{\text{total}} = 2.83 \times 10^{-3}\text{ m} = 2.83\text{ mm}

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student treats the full weight of the column as acting uniformly across the entire height rather than accounting for the linearly varying self-weight, omitting the factor of 1/2.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    W = ρ\rho A H_0 g

  2. Step 2

    σ=WA=ρgH0\sigma = \frac{W}{A} = \rho g H_0

    Correct

    F(y) = ρ\rho A (H_0 - y)g   ⟹  \implies σ\sigma(y) = F(y)A\frac{F(y)}{A} = ρ\rho g (H_0 - y)

    You assumed that the compressive stress is uniform along the entire column. Because each horizontal cross-section supports only the weight of the segment above it, the internal compressive force varies with height from zero at the top (y=H0y = H_0) to a maximum of ρgH0\rho g H_0 at the base (y=0y = 0).

  3. Step 3

    \varepsilon = σE\frac{\sigma}{E} = ρgH0E\frac{\rho g H_0}{E}   ⟹  \implies Δ\Delta H_{total\text{total}} = \varepsilon H_0 = ρgH02E\frac{\rho g H_0^2}{E}_

    Correct

    Δ\Delta H_{total\text{total}} = \int_0^{H_0} σ(y)E\frac{\sigma(y)}{E},dy = \int_0^{H_0} ρg(H0−y)E\frac{\rho g (H_0 - y)}{E},dy = ρgH022E\frac{\rho g H_0^2}{2E}_

    Because the stress was assumed to be constant, you multiplied uniform strain by H0H_0 instead of integrating the local strain, which missed the factor of 12\frac{1}{2}.

  4. Step 4

    Δ\Delta H_{total\text{total}} = 2400×9.80×85.023.00×1010\frac{2400 \times 9.80 \times 85.0^2}{3.00 \times 10^{10}} = 1.699×1083.00×1010\frac{1.699 \times 10^8}{3.00 \times 10^{10}} = 5.66 ×\times 10^{-3} m\text{ m} = 5.66 mm\text{ mm}_

    Correct

    Δ\Delta H_{total\text{total}} = 2400×9.80×85.022(3.00×1010)\frac{2400 \times 9.80 \times 85.0^2}{2(3.00 \times 10^{10})} = 2.83 ×\times 10^{-3} m\text{ m} = 2.83 mm\text{ mm}_

    Your arithmetic evaluation was carried out correctly according to your derived formula, but the result is twice the correct value due to the missing factor of 12\frac{1}{2} in part (a).

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly expressed the total weight of the solid column using density, volume, and gravitational acceleration.

You correctly used Hooke's law relating uniaxial stress to strain through Young's modulus.

You performed the numerical arithmetic and unit conversion accurately.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Uniform load assumption under self-weight

none

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated self-weight as an external top load acting uniformly throughout the body rather than recognizing that internal normal force depends on the coordinate height, requiring integration.

REASONING PATH
Your ACEpath teacher’s suggested approach
Internal Force from Self-Weight
  • For a body deformed under its own weight, the internal normal force at height yy equals the weight of the material above height yy: F(y)=∫yH0ρgA dy′F(y) = \int_y^{H_0} \rho g A\,dy'.

  • Always draw a free-body cut at an arbitrary elevation yy to verify what portion of the mass is supported before defining stress.

Deflection under Linearly Varying Strain
  • Total deformation ΔH\Delta H is the integral of local strain: ΔH=∫0Lε(y) dy\Delta H = \int_0^L \varepsilon(y)\,dy. When stress varies linearly from 00 to σmax⁡\sigma_{\max}, the average stress is 12σmax⁡\frac{1}{2}\sigma_{\max}.

  • Integrate the local strain field over the column's length instead of multiplying maximum strain by total length.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Set up the internal force F(y)F(y) supported by a cross-section at height yy: F(y)=ρA(H0−y)gF(y) = \rho A (H_0 - y) g.

  2. Find the local stress: σ(y)=F(y)A=ρg(H0−y)\sigma(y) = \frac{F(y)}{A} = \rho g (H_0 - y).

  3. Find the local strain: ε(y)=σ(y)E=ρgE(H0−y)\varepsilon(y) = \frac{\sigma(y)}{E} = \frac{\rho g}{E}(H_0 - y).

  4. Integrate the strain over the column height: ΔHtotal=∫0H0ρgE(H0−y) dy=ρgH022E\Delta H_{\text{total}} = \int_0^{H_0} \frac{\rho g}{E}(H_0 - y)\,dy = \frac{\rho g H_0^2}{2E}.

  5. Substitute the numerical values: ΔHtotal=2400×9.80×85.022×(3.00×1010)≈2.83×10−3 m=2.83 mm\Delta H_{\text{total}} = \frac{2400 \times 9.80 \times 85.0^2}{2 \times (3.00 \times 10^{10})} \approx 2.83 \times 10^{-3}\text{ m} = 2.83\text{ mm}.

Final answer

(a) ΔHtotal=ρgH022E\Delta H_{\text{total}} = \frac{\rho g H_0^2}{2E}; (b) ΔHtotal=2.83 mm\Delta H_{\text{total}} = 2.83\text{ mm}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review free-body diagrams for sliced elements under distributed self-weight.

  • Practice computing total elongations or compressions by setting up definite integrals of strain ∫ε(y) dy\int \varepsilon(y)\,dy.

OverviewACEpath Teacher's Diagnosis

02 The student sets the compressive weight at height y as the weight below y rather than above y, leading to an incorrect sign or inverted limit formulation.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    Weight at height yy is W(y)=ρAgy  ⟹  Compressive stress is σ(y)=ρgyW(y) = \rho A g y \implies \text{Compressive stress is } \sigma(y) = \rho g y

    Correct

    F(y)=ρAg(H0−y)  ⟹  σ(y)=ρg(H0−y)F(y) = \rho A g (H_0 - y) \implies \sigma(y) = \rho g (H_0 - y)

    With y=0y = 0 at the rigid base and y=H0y = H_0 at the free top, a cross-section at height yy supports only the weight of the material above it (yy to H0H_0). Your formula ρAgy\rho A g y represents the weight below height yy, which incorrectly predicts maximum stress at the free top (y=H0y = H_0) and zero stress at the base (y=0y = 0).

  2. Step 2

    d(Δy)dy\frac{d(\Delta y)}{dy} = ρgyE\frac{\rho g y}{E}   ⟹  \implies Δ\Delta H_{total\text{total}} = \int_0^{H_0} ρgyE\frac{\rho g y}{E},dy = ρgH022E\frac{\rho g H_0^2}{2E}_

    Correct

    d(Δy)dy\frac{d(\Delta y)}{dy} = ρg(H0−y)E\frac{\rho g (H_0 - y)}{E}   ⟹  \implies Δ\Delta H_{total\text{total}} = \int_0^{H_0} ρg(H0−y)E\frac{\rho g (H_0 - y)}{E},dy = ρgH022E\frac{\rho g H_0^2}{2E}_

    Because ∫0H0y dy=∫0H0(H0−y) dy=H022\int_0^{H_0} y\,dy = \int_0^{H_0} (H_0 - y)\,dy = \frac{H_0^2}{2} by symmetry, your integration yielded the correct symbolic expression despite propagating the inverted stress profile from Step 1.

  3. Step 3

    Δ\Delta H_{total\text{total}} = 2400×9.80×85.022×3.00×1010\frac{2400 \times 9.80 \times 85.0^2}{2 \times 3.00 \times 10^{10}} = 2.83 ×\times 10^{-3} m\text{ m} = 2.83 mm\text{ mm}_

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly related local elastic strain to stress using Hooke's Law.

You integrated the local strain over the full height of the column.

You performed the numerical substitution and unit conversion accurately.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Inverted Load Distribution

none

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You calculated the compressive force on an internal horizontal slice using the volume of the column below the slice rather than the volume of the column resting above it.

REASONING PATH
Your ACEpath teacher’s suggested approach
Free-Body Slice Principle
  • For a vertical column standing on the ground, compressive stress at height yy is caused by the weight of all material lying above height yy.

  • Always test boundary conditions: verify that compressive stress is zero at an unconstrained free surface (σ(H0)=0\sigma(H_0) = 0) and maximum at the supported base (σ(0)=ρgH0\sigma(0) = \rho g H_0).

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Consider a slice at height yy, where y=0y = 0 is the ground and y=H0y = H_0 is the top. The slice supports the segment from yy to H0H_0, which has height (H0−y)(H_0 - y).

  2. The supported compressive force is F(y)=maboveg=ρA(H0−y)gF(y) = m_{\text{above}} g = \rho A (H_0 - y) g.

  3. The local compressive stress is σ(y)=F(y)A=ρg(H0−y)\sigma(y) = \frac{F(y)}{A} = \rho g (H_0 - y), and the strain is ε(y)=ρg(H0−y)E\varepsilon(y) = \frac{\rho g (H_0 - y)}{E}.

  4. Integrate from base to top: ΔHtotal=∫0H0ρg(H0−y)E dy=ρgE[H0y−y22]0H0=ρgH022E\Delta H_{\text{total}} = \int_0^{H_0} \frac{\rho g (H_0 - y)}{E}\,dy = \frac{\rho g}{E}\left[H_0 y - \frac{y^2}{2}\right]_0^{H_0} = \frac{\rho g H_0^2}{2E}.

Final answer

(a) ΔHtotal=ρgH022E\Delta H_{\text{total}} = \frac{\rho g H_0^2}{2E}; (b) ΔHtotal=2.83 mm\Delta H_{\text{total}} = 2.83\text{ mm}

NEXT STEPS
Final Takeaways from Your Teacher
  • Before setting up an integral over a distributed load, always sketch a free-body cut at height yy and check where the boundary stress must vanish.

  • Practice setting up variable-stress integrals for objects hung from the ceiling versus standing on the floor to solidify coordinate choices.

OverviewACEpath Teacher's Diagnosis

03 The student forgets to square the height H₀ during integration of the linear depth term, resulting in incorrect dimensions and numerical magnitude.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    W(y)=ρAg(H0−y)  ⟹  ε(y)=(ρgE)(H0−y)  ⟹  ΔHtotal=∫0H0(ρgE)(H0−y) dyW(y) = \rho A g (H_0 - y) \implies \varepsilon(y) = \left(\frac{\rho g}{E}\right)(H_0 - y) \implies \Delta H_{\text{total}} = \int_0^{H_0} \left(\frac{\rho g}{E}\right)(H_0 - y)\,dy

  2. Step 2

    ΔHtotal=ρgH02E\Delta H_{\text{total}} = \frac{\rho g H_0}{2E}

    Correct

    ΔHtotal=ρgE[H0y−y22]0H0=ρgH022E\Delta H_{\text{total}} = \frac{\rho g}{E} \left[ H_0 y - \frac{y^2}{2} \right]_0^{H_0} = \frac{\rho g H_0^2}{2E}

    When integrating ∫0H0(H0−y) dy\int_0^{H_0} (H_0 - y)\,dy, the antiderivative is H0y−12y2H_0 y - \frac{1}{2}y^2. Evaluating this between 00 and H0H_0 gives H0(H0)−12H02=12H02H_0(H_0) - \frac{1}{2}H_0^2 = \frac{1}{2}H_0^2. You omitted the power of 22 on H0H_0, yielding an expression with dimensions of strain (dimensionless) rather than displacement (meters).

  3. Step 3

    ΔHtotal=2400×9.80×85.02×3.00×1010  ⟹  ΔHtotal=1.999×1066.00×1010  ⟹  ΔHtotal=3.33×10−5 m\Delta H_{\text{total}} = \frac{2400 \times 9.80 \times 85.0}{2 \times 3.00 \times 10^{10}} \implies \Delta H_{\text{total}} = \frac{1.999 \times 10^6}{6.00 \times 10^{10}} \implies \Delta H_{\text{total}} = 3.33 \times 10^{-5}\text{ m}

    Correct

    ΔHtotal=2400×9.80×(85.0)22×(3.00×1010)=2.83×10−3 m=2.83 mm\Delta H_{\text{total}} = \frac{2400 \times 9.80 \times (85.0)^2}{2 \times (3.00 \times 10^{10})} = 2.83 \times 10^{-3}\text{ m} = 2.83\text{ mm}

    Your arithmetic follows your derived formula correctly, but because H0H_0 was not squared, the computed compression is smaller by a factor of H0=85.0H_0 = 85.0.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly determined the weight of the column segment above an arbitrary height yy.

You accurately applied Hooke's law σ=Eε\sigma = E \varepsilon to relate local stress to compressive strain.

You set up the integral over the full height of the column from y=0y = 0 to y=H0y = H_0 with the correct integrand and bounds.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Definite Integration Error / Dimensional Inconsistency

In evaluating ∫0H0(H0−y) dy\int_0^{H_0} (H_0 - y)\,dy, you evaluated the result as H02\frac{H_0}{2} rather than H022\frac{H_0^2}{2}.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated the evaluation of the linear integral as yielding an average height factor without multiplying by the interval length H0H_0, failing to verify the units of the resulting deformation expression.

REASONING PATH
Your ACEpath teacher’s suggested approach
Antiderivative of a Linear Depth Term
  • ∫0L(L−y) dy=[Ly−y22]0L=L2−L22=L22\int_0^L (L - y)\,dy = \left[ L y - \frac{y^2}{2} \right]_0^L = L^2 - \frac{L^2}{2} = \frac{L^2}{2}.

  • Always carry out the antiderivative term-by-term and substitute upper and lower limits explicitly.

Dimensional Sanity Check
  • Strain ε=σE=ρgH0E\varepsilon = \frac{\sigma}{E} = \frac{\rho g H_0}{E} is dimensionless; total displacement ΔH=∫ε dy\Delta H = \int \varepsilon\,dy must have dimensions of length ([m][\text{m}]).

  • Check that your integrated deformation formula contains an extra factor of length compared to strain, which requires H02H_0^2.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. ∫0H0(H0−y) dy=[H0y−y22]0H0=H02−H022=H022\int_0^{H_0} (H_0 - y)\,dy = \left[ H_0 y - \frac{y^2}{2} \right]_0^{H_0} = H_0^2 - \frac{H_0^2}{2} = \frac{H_0^2}{2}

  2. Substitute back into the expression for ΔHtotal\Delta H_{\text{total}}: ΔHtotal=ρgE⋅H022=ρgH022E\Delta H_{\text{total}} = \frac{\rho g}{E} \cdot \frac{H_0^2}{2} = \frac{\rho g H_0^2}{2E}

  3. Substitute the numerical values: ΔHtotal=(2400 kg/m3)(9.80 m/s2)(85.0 m)22(3.00×1010 Pa)\Delta H_{\text{total}} = \frac{(2400\text{ kg/m}^3)(9.80\text{ m/s}^2)(85.0\text{ m})^2}{2(3.00 \times 10^{10}\text{ Pa})}

  4. ΔHtotal=1.69932×108 N/m6.00×1010 Pa≈2.83×10−3 m=2.83 mm\Delta H_{\text{total}} = \frac{1.69932 \times 10^8\text{ N/m}}{6.00 \times 10^{10}\text{ Pa}} \approx 2.83 \times 10^{-3}\text{ m} = 2.83\text{ mm}

Final answer

(a) ΔHtotal=ρgH022E\Delta H_{\text{total}} = \frac{\rho g H_0^2}{2E}; (b) ΔHtotal=2.83×10−3 m=2.83 mm\Delta H_{\text{total}} = 2.83 \times 10^{-3}\text{ m} = 2.83\text{ mm}

NEXT STEPS
Final Takeaways from Your Teacher
  • Write out both antiderivative terms [H0y−y2/2][H_0 y - y^2/2] before evaluating boundary limits.

  • Perform a quick dimensional check whenever deriving a deformation formula: ensure [ΔL]=[m][\Delta L] = [\text{m}].

  • Re-evaluate your numerical calculation with H02=(85.0 m)2H_0^2 = (85.0\text{ m})^2.

Lock it in

Similar question

01

A uniform steel cable of length L=100 mL = 100\text{ m}, cross-sectional area A=2.00×10−4 m2A = 2.00 \times 10^{-4}\text{ m}^2, density ρ=7850 kg/m3\rho = 7850\text{ kg/m}^3, and Young's modulus E=2.00×1011 PaE = 2.00 \times 10^{11}\text{ Pa} hangs vertically from a ceiling under its own weight. Calculate the total elongation ΔL\Delta L of the cable in millimeters. Use g=9.80 m/s2g = 9.80\text{ m/s}^2.

Answer

ΔL=1.92 mm\Delta L = 1.92\text{ mm}. The tension at distance xx from the free bottom is T(x)=ρAgxT(x) = \rho A g x. Integrating strain yields ΔL=∫0LρgxE dx=ρgL22E=7850×9.80×10022×2.00×1011=1.923×10−3 m=1.92 mm\Delta L = \int_0^L \frac{\rho g x}{E}\,dx = \frac{\rho g L^2}{2E} = \frac{7850 \times 9.80 \times 100^2}{2 \times 2.00 \times 10^{11}} = 1.923 \times 10^{-3}\text{ m} = 1.92\text{ mm}.

02

An upright solid column of height H0H_0, density ρ\rho, and Young's modulus EE carries a concentrated load equal to its own total weight W=ρAH0gW = \rho A H_0 g resting on top of it, in addition to its own self-weight. Derive the expression for the total vertical compression ΔH\Delta H in terms of ρ,g,H0,\rho, g, H_0, and EE.

Answer

ΔH=3ρgH022E\Delta H = \frac{3\rho g H_0^2}{2E}. The compressive force at height yy from the base is F(y)=Wtop+Wabove(y)=ρAH0g+ρA(H0−y)g=ρAg(2H0−y)F(y) = W_{\text{top}} + W_{\text{above}}(y) = \rho A H_0 g + \rho A (H_0 - y)g = \rho A g (2H_0 - y). Integrating strain gives ΔH=∫0H0ρg(2H0−y)E dy=ρgE[2H02−H022]=3ρgH022E\Delta H = \int_0^{H_0} \frac{\rho g (2H_0 - y)}{E}\,dy = \frac{\rho g}{E}\left[2H_0^2 - \frac{H_0^2}{2}\right] = \frac{3\rho g H_0^2}{2E}.

03

A truncated solid cone of height HH stands upright on its broad base. Its radius decreases linearly from R0R_0 at the base (y=0y = 0) to 12R0\frac{1}{2}R_0 at the top (y=Hy = H). Set up, but do not fully evaluate, the integral for the total vertical compression ΔH\Delta H under its own self-weight in terms of density ρ\rho, gravity gg, Young's modulus EE, and geometric parameters.

Answer

At height yy, radius is r(y)=R0(1−y2H)r(y) = R_0\left(1 - \frac{y}{2H}\right) and area is A(y)=πr(y)2A(y) = \pi r(y)^2. The weight above yy is W(y)=ρg∫yHA(u) du=13πρg[r(y)2(2H−y)−(R02)2(0)]W(y) = \rho g \int_y^H A(u)\,du = \frac{1}{3}\pi \rho g \left[r(y)^2(2H - y) - \left(\frac{R_0}{2}\right)^2(0)\right] (or volume of truncated cone). The strain is ε(y)=W(y)A(y)E\varepsilon(y) = \frac{W(y)}{A(y)E}. Total compression is ΔH=∫0Hρg∫yHπr(u)2 duπr(y)2E dy\Delta H = \int_0^H \frac{\rho g \int_y^H \pi r(u)^2\,du}{\pi r(y)^2 E}\,dy.

Loading workspace…