Resources
A worker pulls a heavy tool chest of mass across a factory floor by applying a tension force of via a strap angled at above the horizontal. As the chest moves horizontally to the right over a displacement of , a persistent headwind and floor drag exert a horizontal retarding force of directed to the left. Adhering strictly to coordinate sign conventions (), compute the individual work done by the tension force , the work done by the retarding force , the work done by gravity , and the net work performed on the chest.
Answer and steps
Final answer
, , ,
Steps
Work Done by the Tension Force ()
To find the work done by each force, we apply the definition of work for a constant force: where is the magnitude of the force, is the magnitude of the displacement, and is the angle between the force vector and the displacement vector. Here, the displacement is directed horizontally to the right with magnitude .
The tension force has magnitude and acts at an angle of relative to the horizontal displacement:
Work Done by the Retarding Force ()
The retarding force has magnitude and opposes the motion, pointing directly to the left. The angle between the drag force and the displacement is :
Work Done by Gravity ()
The force of gravity points vertically downward, perpendicular to the horizontal displacement ():
(Similarly, the upward normal force from the floor is also perpendicular to the motion and performs zero work: .)
Net Work Done on the Chest ()
The net work equals the algebraic sum of the individual works done by all forces acting on the chest:
Common Pitfall: A frequent error is using the full magnitude of the tension vector directly without resolving it along the direction of motion, or forgetting the negative sign on opposing forces. Always use to properly account for vector directions.
Typical errors
01 The student ignores the angle of the applied tension force and assumes work is simply the magnitude of tension multiplied by displacement.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
Because the tension is applied at an angle of above the horizontal displacement, only its horizontal component does work. You need to include the factor in the dot product.
- Step 2
- Step 3
- Step 4Correct
Your method of summing the individual works is completely correct, but the numerical result is off because of the earlier value for .
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly used to compute the negative work done by the retarding force.
You correctly recognized that the perpendicular gravitational force does zero work.
You correctly summed individual work quantities to find the net work.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou treated tension as acting parallel to displacement instead of multiplying by .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisIncomplete application of the definition of work when a force is angled relative to the displacement vector.
REASONING PATH
Your ACEpath teacher’s suggested approach- Angle Check
For any constant force acting over displacement , the work done is , where is the angle between and .
Draw a quick vector diagram for each force and verify whether the force has an angle relative to the displacement vector before multiplying magnitudes.
CORRECTED PATH
ACEpath Teacher's DemonstrationSubstitute into the work formula: .
Re-sum the net work: .
02 The student treats work as always positive by omitting the negative sign resulting from the drag force opposing the displacement.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
Because the retarding drag force acts directly opposite the chest's displacement to the right, the angle between the force and displacement vectors is , which gives a negative sign via .
- Step 3
- Step 4Correct
Your summation method was correct, but the final net work was affected by the sign error from .
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly applied the dot product formula to the tension force at .
You recognized that perpendicular forces like gravity do zero work because .
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou treated work as an unsigned product of magnitudes () rather than including the directional angle for the opposing drag force.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisTreating work as a strictly non-negative scalar rather than a signed quantity where forces opposing motion remove mechanical energy from the system.
REASONING PATH
Your ACEpath teacher’s suggested approach- Vector Alignment & Work Sign
Always explicitly check the angle between the force vector and the displacement vector: forces pointing opposite to motion have and do negative work.
CORRECTED PATH
ACEpath Teacher's DemonstrationSubstitute into the work formula: .
Sum the individual work values: .
, , ,
03 The student uses the vertical component sine instead of cosine for the horizontal work done by the angled tension force.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
The work done by a constant force is defined by the scalar product . Because the angle is measured relative to the horizontal displacement vector, the component along the direction of motion is given by the cosine, not the sine.
- Step 2
- Step 3
- Step 4Correct
Your method of summing the work from all individual forces was correct, but the numerical result was affected by the error in from step 1.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly used the angle to find the work done by the opposing drag force.
You correctly recognized that perpendicular forces like gravity do zero work.
You correctly summed the individual works to evaluate the net work.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou substituted instead of when finding the work done by tension parallel to the horizontal displacement.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing which trigonometric ratio projects a vector onto the axis parallel to the displacement versus the perpendicular axis.
REASONING PATH
Your ACEpath teacher’s suggested approach- Scalar Product Definition
For a constant force at an angle to displacement , .
Always verify that is the angle directly between the force vector and displacement vector, and use cosine for the dot product.
- Parallel Component Check
Only the component of force along the line of motion does work: when is measured from the surface.
Sketch the right triangle formed by the force vector to confirm that the horizontal leg adjacent to uses cosine.
CORRECTED PATH
ACEpath Teacher's DemonstrationCalculate tension work using the cosine of the angle with displacement: .
Sum the individual work contributions: .
, , ,
Lock it in
What is the general formula for the work done by a constant force over a straight-line displacement ?
, where is the angle between the force vector and the displacement vector.
Similar question
A sled is pulled along a flat horizontal surface over a distance of by a rope with tension directed at above the horizontal. Calculate the work done by the rope on the sled.
Answer
A lawnmower is pushed across a horizontal lawn by a downward handle force of directed at an angle of below the horizontal. If the mower moves forward by against a constant horizontal friction force of , find the work done by the pushing force and the net work done on the mower.
Answer
; ;
A crate of mass is pulled up a frictionless ramp inclined at to the horizontal by an applied force of directed parallel to the incline. Taking , calculate the work done by the applied force, the work done by gravity, and the net work done on the crate.
Answer
Applied force is parallel to displacement: . Gravity opposes the upward motion at angle : (or ).