Resources

In a materials testing lab, a tensile test yields an engineering stress of σ=245 MPa\sigma = 245\text{ MPa}. A student attempts to calculate the tensile force applied across a circular cross-section of radius r=4.00 mmr = 4.00\text{ mm} using the formula F=σA=σ(πr2)F = \sigma A = \sigma (\pi r^2). If the student fails to convert millimeters to meters and mistakenly substitutes r=4.00r = 4.00 directly into πr2\pi r^2 while using σ=245×106 Pa\sigma = 245 \times 10^6\text{ Pa}, determine the ratio of this incorrect calculated force to the true physical force in newtons (Fcalc/FtrueF_{\text{calc}} / F_{\text{true}}), and compute the true physical force in kilonewtons (kN\text{kN}).

Answer and steps

Final answer

Ratio Fcalc/Ftrue=106F_{\text{calc}} / F_{\text{true}} = 10^6; true physical force Ftrue=12.3 kNF_{\text{true}} = 12.3\text{ kN}

Steps

01

Identify True and Incorrect Quantities in SI Units

The relationship between tensile force FF, stress σ\sigma, and cross-sectional area AA is: F=σA=σπr2F = \sigma A = \sigma \pi r^2

To calculate force in standard SI units (newtons, N\text{N}), every quantity must be expressed in base SI units:

  • Stress: σ=245 MPa=245×106 Pa=245×106 N/m2\sigma = 245\text{ MPa} = 245 \times 10^6\text{ Pa} = 245 \times 10^6\text{ N/m}^2
  • True radius: rtrue=4.00 mm=4.00×10−3 mr_{\text{true}} = 4.00\text{ mm} = 4.00 \times 10^{-3}\text{ m}

The student erroneously uses the numerical value of radius in millimeters without conversion:

  • Incorrect radius value: rcalc=4.00r_{\text{calc}} = 4.00 (effectively treating millimeters as meters)

02

Determine the Ratio Fcalc/FtrueF_{\text{calc}} / F_{\text{true}}

Write both forces in terms of the formula: Ftrue=σπrtrue2=σπ(4.00×10−3)2F_{\text{true}} = \sigma \pi r_{\text{true}}^2 = \sigma \pi (4.00 \times 10^{-3})^2 Fcalc=σπrcalc2=σπ(4.00)2F_{\text{calc}} = \sigma \pi r_{\text{calc}}^2 = \sigma \pi (4.00)^2

Taking the ratio of the calculated force to the true force: FcalcFtrue=σπ(4.00)2σπ(4.00×10−3)2=1(10−3)2=110−6=106\frac{F_{\text{calc}}}{F_{\text{true}}} = \frac{\sigma \pi (4.00)^2}{\sigma \pi (4.00 \times 10^{-3})^2} = \frac{1}{(10^{-3})^2} = \frac{1}{10^{-6}} = 10^6

Common Pitfall: When converting units of area, the linear conversion factor must also be squared. Because 1 mm=10−3 m1\text{ mm} = 10^{-3}\text{ m}, the area conversion is 1 mm2=(10−3 m)2=10−6 m21\text{ mm}^2 = (10^{-3}\text{ m})^2 = 10^{-6}\text{ m}^2. Forgetting to convert units at the linear stage leads to an answer that is off by a factor of 10610^6 (one million), not merely 10310^3.


03

Compute the True Physical Force (FtrueF_{\text{true}})

Substitute the SI values into the force equation: Atrue=πrtrue2=π(4.00×10−3 m)2=16.00π×10−6 m2A_{\text{true}} = \pi r_{\text{true}}^2 = \pi (4.00 \times 10^{-3}\text{ m})^2 = 16.00\pi \times 10^{-6}\text{ m}^2

Now compute the force: Ftrue=(245×106 N/m2)×(16.00π×10−6 m2)F_{\text{true}} = (245 \times 10^6\text{ N/m}^2) \times (16.00\pi \times 10^{-6}\text{ m}^2) Ftrue=245×16.00π N=3920π N≈12315 NF_{\text{true}} = 245 \times 16.00\pi\text{ N} = 3920\pi\text{ N} \approx 12315\text{ N}

Convert newtons to kilonewtons (kN\text{kN}), keeping three significant figures: Ftrue=12315 N1000 N/kN≈12.3 kNF_{\text{true}} = \frac{12315\text{ N}}{1000\text{ N/kN}} \approx 12.3\text{ kN}

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student forgets to square the unit conversion factor when comparing areas, concluding that the ratio of the forces is 10³ instead of 10⁶.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    FcalcFtrue=rcalcrtrue=4.004.00×10−3  ⟹  FcalcFtrue=103\frac{F_{\text{calc}}}{F_{\text{true}}} = \frac{r_{\text{calc}}}{r_{\text{true}}} = \frac{4.00}{4.00 \times 10^{-3}} \implies \frac{F_{\text{calc}}}{F_{\text{true}}} = 10^3

    Correct

    FcalcFtrue=σπrcalc2σπrtrue2=(rcalcrtrue)2=(4.004.00×10−3)2=106\frac{F_{\text{calc}}}{F_{\text{true}}} = \frac{\sigma \pi r_{\text{calc}}^2}{\sigma \pi r_{\text{true}}^2} = \left(\frac{r_{\text{calc}}}{r_{\text{true}}}\right)^2 = \left(\frac{4.00}{4.00 \times 10^{-3}}\right)^2 = 10^6

    Force depends on cross-sectional area, which is proportional to r2r^2. When setting up the ratio of forces, you must square the ratio of the radii.

  2. Step 2

    A=π⋅(0.00400 m)2=5.027×10−5 m2A = \pi \cdot (0.00400\text{ m})^2 = 5.027 \times 10^{-5}\text{ m}^2

  3. Step 3

    Ftrue=245×106 Pa⋅5.027×10−5 m2=12316 N  ⟹  Ftrue=12.3 kNF_{\text{true}} = 245 \times 10^6\text{ Pa} \cdot 5.027 \times 10^{-5}\text{ m}^2 = 12316\text{ N} \implies F_{\text{true}} = 12.3\text{ kN}

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly converted millimeters to meters when finding the true physical cross-sectional area.

You correctly applied F=σAF = \sigma A to find the true force in newtons and converted it to kilonewtons.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Omitted exponent in ratio comparison

No, this is a conceptual slip in setting up ratios where the dependent quantity scales with area (r2r^2) rather than linear length (rr).

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You related force directly to the linear radius ratio rcalc/rtruer_{\text{calc}} / r_{\text{true}} rather than the area ratio (rcalc/rtrue)2(r_{\text{calc}} / r_{\text{true}})^2. Since area scales quadratically, omitting the power of 2 undercounts the conversion factor scale by a factor of 10310^3.

REASONING PATH
Your ACEpath teacher’s suggested approach
Scaling Laws in Proportional Formulas
  • If a physical quantity YY is proportional to XnX^n, then Y1Y2=(X1X2)n\frac{Y_1}{Y_2} = \left(\frac{X_1}{X_2}\right)^n.

  • Always write the full formula for both states and cancel shared constants before evaluating numerical ratios.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Write out the ratio of the complete force expressions: FcalcFtrue=σπrcalc2σπrtrue2\frac{F_{\text{calc}}}{F_{\text{true}}} = \frac{\sigma \pi r_{\text{calc}}^2}{\sigma \pi r_{\text{true}}^2}.

  2. Cancel the common factor σπ\sigma \pi: FcalcFtrue=(rcalcrtrue)2\frac{F_{\text{calc}}}{F_{\text{true}}} = \left(\frac{r_{\text{calc}}}{r_{\text{true}}}\right)^2.

  3. Substitute the numerical values: (4.004.00×10−3)2=(103)2=106\left(\frac{4.00}{4.00 \times 10^{-3}}\right)^2 = (10^3)^2 = 10^6.

Final answer

Ratio Fcalc/Ftrue=106F_{\text{calc}} / F_{\text{true}} = 10^6; true physical force Ftrue=12.3 kNF_{\text{true}} = 12.3\text{ kN}

NEXT STEPS
Final Takeaways from Your Teacher
  • When comparing two quantities defined by geometric formulas, write out the algebraic ratio first to verify which powers apply to each variable.

  • Double-check that area conversions always square linear conversion factors: (10−3)2=10−6(10^{-3})^2 = 10^{-6}.

OverviewACEpath Teacher's Diagnosis

02 The student treats the given radius as the diameter and calculates the cross-sectional area using radius 2.00 mm, underestimating the true force by a factor of 4.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    FcalcFtrue=(4.00)2(4.00×10−3)2=106\frac{F_{\text{calc}}}{F_{\text{true}}} = \frac{(4.00)^2}{(4.00 \times 10^{-3})^2} = 10^6

  2. Step 2

    rtrue=4.00 mm2=2.00 mm=0.00200 mr_{\text{true}} = \frac{4.00\text{ mm}}{2} = 2.00\text{ mm} = 0.00200\text{ m}

    Correct

    rtrue=4.00 mm=4.00×10−3 mr_{\text{true}} = 4.00\text{ mm} = 4.00 \times 10^{-3}\text{ m}

    The problem states that the cross-section has a radius of r=4.00 mmr = 4.00\text{ mm}, not a diameter. Dividing by 22 halved the true radius to 2.00 mm2.00\text{ mm}.

  3. Step 3

    A=π⋅(0.00200 m)2=1.257×10−5 m2  ⟹  Ftrue=245×106 Pa⋅1.257×10−5 m2=3080 N  ⟹  Ftrue=3.08 kNA = \pi \cdot (0.00200\text{ m})^2 = 1.257 \times 10^{-5}\text{ m}^2 \implies F_{\text{true}} = 245 \times 10^6\text{ Pa} \cdot 1.257 \times 10^{-5}\text{ m}^2 = 3080\text{ N} \implies F_{\text{true}} = 3.08\text{ kN}

    Correct

    A=π(4.00×10−3 m)2≈5.027×10−5 m2  ⟹  Ftrue=(245×106 Pa)(5.027×10−5 m2)≈1.23×104 N=12.3 kNA = \pi (4.00 \times 10^{-3}\text{ m})^2 \approx 5.027 \times 10^{-5}\text{ m}^2 \implies F_{\text{true}} = (245 \times 10^6\text{ Pa})(5.027 \times 10^{-5}\text{ m}^2) \approx 1.23 \times 10^4\text{ N} = 12.3\text{ kN}

    Your area and force calculations followed the correct algebraic formulas, but your final answer is an underestimate by a factor of 44 because you substituted r=2.00 mmr = 2.00\text{ mm} instead of r=4.00 mmr = 4.00\text{ mm}.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly solved for the error magnification ratio Fcalc/Ftrue=106F_{\text{calc}} / F_{\text{true}} = 10^6.

You converted millimeters to meters accurately when setting up your numerical area calculation.

You correctly applied the tensile force formula F=σAF = \sigma A and converted newtons to kilonewtons.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Radius vs. Diameter Confusion

You divided the dimension 4.00 mm4.00\text{ mm} by 22, mistaking the stated radius for a diameter.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Habitually halving any circular dimension before applying A=πr2A = \pi r^2 without verifying whether the problem statement supplied a radius rr or a diameter dd.

REASONING PATH
Your ACEpath teacher’s suggested approach
Check the given circular dimension
  • Only divide by 22 if the problem provides diameter dd (r=d/2r = d/2). If the problem explicitly provides radius rr, use it directly.

  • Highlight the word 'radius' or 'diameter' in the problem prompt before writing down the formula.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Use the given radius directly: r=4.00 mm=4.00×10−3 mr = 4.00\text{ mm} = 4.00 \times 10^{-3}\text{ m}.

  2. Calculate the true cross-sectional area: A=πr2=π(4.00×10−3 m)2=1.600π×10−5 m2≈5.027×10−5 m2A = \pi r^2 = \pi (4.00 \times 10^{-3}\text{ m})^2 = 1.600\pi \times 10^{-5}\text{ m}^2 \approx 5.027 \times 10^{-5}\text{ m}^2.

  3. Calculate the true tensile force: Ftrue=σA=(245×106 Pa)(5.027×10−5 m2)≈12315 NF_{\text{true}} = \sigma A = (245 \times 10^6\text{ Pa})(5.027 \times 10^{-5}\text{ m}^2) \approx 12315\text{ N}.

  4. Convert to kilonewtons: Ftrue=12.3 kNF_{\text{true}} = 12.3\text{ kN}.

Final answer

Ratio Fcalc/Ftrue=106F_{\text{calc}} / F_{\text{true}} = 10^6; Ftrue=12.3 kNF_{\text{true}} = 12.3\text{ kN}

NEXT STEPS
Final Takeaways from Your Teacher
  • Double-check every problem statement to see if a circular cross-section is specified by radius rr or diameter dd.

  • Practice checking whether squaring a halved radius will inadvertently reduce your area by a factor of 22=42^2 = 4.

OverviewACEpath Teacher's Diagnosis

03 The student omits the conversion from newtons to kilonewtons in the final step, reporting the true force as 12315 kN instead of converting to 12.3 kN.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    FcalcFtrue=(4.00)2(0.00400)2=106\frac{F_{\text{calc}}}{F_{\text{true}}} = \frac{(4.00)^2}{(0.00400)^2} = 10^6

  2. Step 2

    A=π⋅(4.00×10−3 m)2=5.027×10−5 m2  ⟹  Ftrue=245×106 Pa⋅5.027×10−5 m2=12315 NA = \pi \cdot (4.00 \times 10^{-3}\text{ m})^2 = 5.027 \times 10^{-5}\text{ m}^2 \implies F_{\text{true}} = 245 \times 10^6\text{ Pa} \cdot 5.027 \times 10^{-5}\text{ m}^2 = 12315\text{ N}

  3. Step 3

    Ftrue=12315 kNF_{\text{true}} = 12315\text{ kN}

    Correct

    Ftrue=12315 N1000 N/kN≈12.3 kNF_{\text{true}} = \frac{12315\text{ N}}{1000\text{ N/kN}} \approx 12.3\text{ kN}

    You replaced the unit N\text{N} with kN\text{kN} without dividing the numerical value by 10001000 (10310^3), which made your final answer 10001000 times too large.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly determined the ratio of the erroneous force to the true force as 10610^6.

You accurately converted millimeters to meters when evaluating the true cross-sectional area.

You correctly computed the true tensile force in base SI units as 12315 N12315\text{ N}.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Metric Prefix Scaling Error

You replaced the unit symbol N\text{N} with kN\text{kN} without dividing the numerical value by 10001000.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Treating unit conversion as a simple label substitution rather than an algebraic equivalence where inserting a factor of 10310^3 (kilo) requires dividing the number by 10310^3 to keep the physical quantity unchanged.

REASONING PATH
Your ACEpath teacher’s suggested approach
Unit Invariance via Conversion Factors
  • To preserve equality, multiply by a conversion factor equal to 11, such as (1 kN103 N)\left(\frac{1\text{ kN}}{10^3\text{ N}}\right).

  • Write out the unit conversion factor explicitly so the unwanted unit cancels out algebraically.

Magnitude Sanity Check
  • A larger unit must accompany a smaller numerical value for the same physical quantity.

  • Check that converting from a smaller base unit (N\text{N}) to a larger prefixed unit (kN\text{kN}) reduces the numerical magnitude by 10310^3.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Multiply by the conversion factor 1 kN1000 N\frac{1\text{ kN}}{1000\text{ N}}: Ftrue=12315 N×1 kN1000 N=12.315 kNF_{\text{true}} = 12315\text{ N} \times \frac{1\text{ kN}}{1000\text{ N}} = 12.315\text{ kN}

  2. Round to three significant figures consistent with the input data: 12.315 kN≈12.3 kN12.315\text{ kN} \approx 12.3\text{ kN}

Final answer

Fcalc/Ftrue=106F_{\text{calc}} / F_{\text{true}} = 10^6; Ftrue=12.3 kNF_{\text{true}} = 12.3\text{ kN}

NEXT STEPS
Final Takeaways from Your Teacher
  • Always write out conversion factors with explicit units to cancel out base units algebraically.

  • Perform a quick magnitude check whenever adding or removing metric prefixes: larger units require smaller numbers.

Lock it in

Similar question

01

A pressure sensor has a circular diaphragm of radius r=2.0 mmr = 2.0\text{ mm}. A student calculates the force from pressure P=1.5 MPaP = 1.5\text{ MPa} using F=P(πr2)F = P(\pi r^2), but substitutes r=2.0r = 2.0 instead of 2.0×10−3 m2.0 \times 10^{-3}\text{ m}. What is the ratio Fcalc/FtrueF_{\text{calc}} / F_{\text{true}}?

Answer

10610^6. Since F∝r2F \propto r^2, the ratio is (rcalc/rtrue)2=(2.0/(2.0×10−3))2=(103)2=106(r_{\text{calc}} / r_{\text{true}})^2 = (2.0 / (2.0 \times 10^{-3}))^2 = (10^3)^2 = 10^6.

02

A hydraulic press piston has a diameter of d=20.0 cmd = 20.0\text{ cm}. Calculate its cross-sectional area in square meters (m2\text{m}^2), expressing your answer in scientific notation to three significant figures.

Answer

3.14×10−2 m23.14 \times 10^{-2}\text{ m}^2. Radius r=10.0 cm=0.100 mr = 10.0\text{ cm} = 0.100\text{ m}. Area A=πr2=π(0.100 m)2=0.0100π m2≈3.14×10−2 m2A = \pi r^2 = \pi (0.100\text{ m})^2 = 0.0100\pi\text{ m}^2 \approx 3.14 \times 10^{-2}\text{ m}^2.

03

A structural rod carries an axial load. If its radius is mistakenly measured as 5.0 mm5.0\text{ mm} instead of the true value of 2.5 mm2.5\text{ mm}, by what factor is the calculated stress σ=F/A\sigma = F/A underestimated relative to the true stress (i.e., find σcalc/σtrue\sigma_{\text{calc}} / \sigma_{\text{true}})?

Answer

0.250.25 (or 1/41/4). Stress is inversely proportional to area: σ∝1/r2\sigma \propto 1/r^2. Thus, σcalc/σtrue=(rtrue/rcalc)2=(2.5/5.0)2=(1/2)2=1/4=0.25\sigma_{\text{calc}} / \sigma_{\text{true}} = (r_{\text{true}} / r_{\text{calc}})^2 = (2.5 / 5.0)^2 = (1/2)^2 = 1/4 = 0.25.

Loading workspace…