Resources

A crate of mass m=18.0 kgm = 18.0\text{ kg} rests on a rough horizontal warehouse floor where the coefficient of kinetic friction is μk=0.280\mu_k = 0.280. A worker pulls the crate across the floor with a tension force FT=75.0 NF_T = 75.0\text{ N} directed at an angle θ=25.0∘\theta = 25.0^\circ above the horizontal. Assuming g=9.80 m/s2g = 9.80\text{ m/s}^2, construct the equations of motion from the free-body diagram along the vertical and horizontal axes, and determine the magnitude of the normal force FNF_N exerted by the floor on the crate and the resulting horizontal acceleration axa_x.

Answer and steps

Final answer

FN=145 NF_N = 145\text{ N}, ax=1.52 m/s2a_x = 1.52\text{ m/s}^2

Steps

01

Identify all forces acting on the crate

Choose a coordinate system where the positive xx-axis points in the forward direction of motion (to the right) and the positive yy-axis points vertically upward.

The forces acting on the crate are:

  1. Gravity (Fg=mgF_g = mg), pointing vertically downward.
  2. Normal force (FNF_N), exerted perpendicularly upward by the floor.
  3. Tension (FTF_T), directed at an angle θ=25.0∘\theta = 25.0^\circ above the horizontal.
  4. Kinetic friction (fkf_k), opposing the forward motion and directed to the left along the floor.

02

Resolve the tension force into components

Because the tension is applied at an angle to the floor, it has both horizontal and vertical components:

  • Horizontal component: FTx=FTcos⁡θ=75.0 N⋅cos⁡(25.0∘)≈67.97 NF_{Tx} = F_T \cos\theta = 75.0\text{ N} \cdot \cos(25.0^\circ) \approx 67.97\text{ N}
  • Vertical component: FTy=FTsin⁡θ=75.0 N⋅sin⁡(25.0∘)≈31.70 NF_{Ty} = F_T \sin\theta = 75.0\text{ N} \cdot \sin(25.0^\circ) \approx 31.70\text{ N}

03

Apply Newton's Second Law along the vertical axis

The crate remains on the floor without accelerating vertically, so ay=0 m/s2a_y = 0\text{ m/s}^2. Balancing vertical forces: ΣFy=FN+FTsin⁡θ−mg=0\Sigma F_y = F_N + F_T \sin\theta - mg = 0

Solving for the normal force FNF_N: FN=mg−FTsin⁡θF_N = mg - F_T \sin\theta

Substitute the given values: mg=(18.0 kg)(9.80 m/s2)=176.4 Nmg = (18.0\text{ kg})(9.80\text{ m/s}^2) = 176.4\text{ N} FN=176.4 N−31.70 N=144.70 N≈145 NF_N = 176.4\text{ N} - 31.70\text{ N} = 144.70\text{ N} \approx 145\text{ N}

Common Pitfall: Do not assume the normal force equals the full gravitational weight (FN=mgF_N = mg). Because the upward component of the pulling force partially supports the crate's weight, the floor exerts less normal force.


04

Calculate the kinetic friction force

The magnitude of kinetic friction depends directly on the normal force: fk=μkFNf_k = \mu_k F_N fk=(0.280)(144.70 N)≈40.52 Nf_k = (0.280)(144.70\text{ N}) \approx 40.52\text{ N}

Using the rounded normal force (145 N145\text{ N}): fk≈(0.280)(145 N)=40.6 Nf_k \approx (0.280)(145\text{ N}) = 40.6\text{ N}


05

Apply Newton's Second Law along the horizontal axis

Along the horizontal axis, the net force causes an acceleration axa_x: ΣFx=FTcos⁡θ−fk=max\Sigma F_x = F_T \cos\theta - f_k = m a_x

Rearranging to solve for axa_x: ax=FTcos⁡θ−fkma_x = \frac{F_T \cos\theta - f_k}{m}

Substitute the values: ax=67.97 N−40.6 N18.0 kg=27.37 N18.0 kg≈1.52 m/s2a_x = \frac{67.97\text{ N} - 40.6\text{ N}}{18.0\text{ kg}} = \frac{27.37\text{ N}}{18.0\text{ kg}} \approx 1.52\text{ m/s}^2

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student assumes the normal force equals the crate's weight (F_N = mg) by omitting the vertical component of the pulling force, which overestimates friction and underestimates acceleration.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    FN=m⋅g  ⟹  FN=18.0⋅9.80=176.4 NF_N = m \cdot g \implies F_N = 18.0 \cdot 9.80 = 176.4\text{ N}

    Correct

    ΣFy=FN+FTsin⁡(25.0∘)−mg=0  ⟹  FN=mg−FTsin⁡(25.0∘)≈145 N\Sigma F_y = F_N + F_T \sin(25.0^\circ) - mg = 0 \implies F_N = mg - F_T \sin(25.0^\circ) \approx 145\text{ N}

    You omitted the upward vertical component of the tension force (FTsin⁡θF_T \sin\theta). Because the worker pulls upward at an angle, the tension partially supports the crate's weight, making FNF_N strictly less than mgmg.

  2. Step 2

    fk=μk⋅FN=0.280⋅176.4=49.39 Nf_k = \mu_k \cdot F_N = 0.280 \cdot 176.4 = 49.39\text{ N}

    Correct

    fk=μkFN=0.280⋅144.70 N≈40.5 Nf_k = \mu_k F_N = 0.280 \cdot 144.70\text{ N} \approx 40.5\text{ N}

    You correctly applied the kinetic friction definition fk=μkFNf_k = \mu_k F_N, but the calculated friction value is too high because it inherited the incorrect normal force from Step 1.

  3. Step 3

    FTcos⁡(25.0∘)−fk=m⋅ax  ⟹  75.0cos⁡(25.0∘)−49.39=18.0⋅ax  ⟹  67.97−49.39=18.0⋅ax  ⟹  18.58=18.0⋅ax  ⟹  ax=1.03 m/s2F_T \cos(25.0^\circ) - f_k = m \cdot a_x \implies 75.0 \cos(25.0^\circ) - 49.39 = 18.0 \cdot a_x \implies 67.97 - 49.39 = 18.0 \cdot a_x \implies 18.58 = 18.0 \cdot a_x \implies a_x = 1.03\text{ m/s}^2

    Correct

    ax=FTcos⁡(25.0∘)−fkm=67.97 N−40.52 N18.0 kg≈1.52 m/s2a_x = \frac{F_T \cos(25.0^\circ) - f_k}{m} = \frac{67.97\text{ N} - 40.52\text{ N}}{18.0\text{ kg}} \approx 1.52\text{ m/s}^2

    Your horizontal force balance and algebraic steps were carried out properly, but the resulting acceleration is lower than expected due to the overestimated friction force.

WHAT YOU DID WELL
Compliments from Your Teacher

You resolved the horizontal component of the tension force using FTcos⁡θF_T \cos\theta correctly.

You correctly used Newton's second law along the horizontal axis to relate net horizontal force to mass and acceleration.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Omitted Force Component in Vertical Equilibrium

none

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated the normal force as an automatic default equal to weight (FN=mgF_N = mg) instead of deriving it from the vertical equilibrium equation ΣFy=0\Sigma F_y = 0, forgetting that an upward-angled pull relieves part of the contact force from the floor.

REASONING PATH
Your ACEpath teacher’s suggested approach
Always sum forces along the perpendicular axis
  • For a surface with no vertical motion, set ΣFy=0\Sigma F_y = 0 including all vertical components: FN+FT,y−Fg=0F_N + F_{T,y} - F_g = 0.

  • Draw a complete free-body diagram and resolve every off-axis vector into components before writing down FNF_N.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Set up vertical force balance: ΣFy=FN+FTsin⁡(25.0∘)−mg=0\Sigma F_y = F_N + F_T \sin(25.0^\circ) - mg = 0.

  2. Solve for normal force: FN=(18.0 kg)(9.80 m/s2)−(75.0 N)sin⁡(25.0∘)=176.4 N−31.70 N≈144.7 NF_N = (18.0\text{ kg})(9.80\text{ m/s}^2) - (75.0\text{ N})\sin(25.0^\circ) = 176.4\text{ N} - 31.70\text{ N} \approx 144.7\text{ N}.

  3. Recalculate kinetic friction: fk=μkFN=0.280×144.7 N≈40.52 Nf_k = \mu_k F_N = 0.280 \times 144.7\text{ N} \approx 40.52\text{ N}.

  4. Solve for horizontal acceleration: ax=75.0cos⁡(25.0∘)−40.5218.0=67.97−40.5218.0≈1.52 m/s2a_x = \frac{75.0\cos(25.0^\circ) - 40.52}{18.0} = \frac{67.97 - 40.52}{18.0} \approx 1.52\text{ m/s}^2.

Final answer

FN=145 NF_N = 145\text{ N}, ax=1.52 m/s2a_x = 1.52\text{ m/s}^2

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice drawing free-body diagrams where applied forces act at angles above or below the horizontal.

  • Write out the full summation equation ΣFy=may=0\Sigma F_y = m a_y = 0 every time instead of substituting FN=mgF_N = mg by habit.

OverviewACEpath Teacher's Diagnosis

02 The student adds the vertical component of the tension force to the weight instead of subtracting it when solving for the normal force, leading to an artificially increased normal force and reduced acceleration.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    FN=mg+FTsin⁡(25.0∘)  ⟹  FN=18.0×9.80+75.0sin⁡(25.0∘)  ⟹  FN=176.4+31.70=208.1 NF_N = mg + F_T \sin(25.0^\circ) \implies F_N = 18.0 \times 9.80 + 75.0 \sin(25.0^\circ) \implies F_N = 176.4 + 31.70 = 208.1\text{ N}

    Correct

    FN+FTsin⁡(25.0∘)−mg=0  ⟹  FN=mg−FTsin⁡(25.0∘)=176.4−31.70=144.7 N≈145 NF_N + F_T \sin(25.0^\circ) - mg = 0 \implies F_N = mg - F_T \sin(25.0^\circ) = 176.4 - 31.70 = 144.7\text{ N} \approx 145\text{ N}

    Because the worker pulls upward at 25.0∘25.0^\circ, the vertical component FTsin⁡(25.0∘)F_T \sin(25.0^\circ) acts upward along with the normal force FNF_N, partially counteracting gravity (mgmg). The vertical equilibrium equation is FN+FTsin⁡(25.0∘)−mg=0F_N + F_T \sin(25.0^\circ) - mg = 0, which gives FN=mg−FTsin⁡(25.0∘)F_N = mg - F_T \sin(25.0^\circ), not mg+FTsin⁡(25.0∘)mg + F_T \sin(25.0^\circ).

  2. Step 2

    fk=μkFN=0.280×208.1=58.27 Nf_k = \mu_k F_N = 0.280 \times 208.1 = 58.27\text{ N}

    Correct

    fk=μkFN=0.280×144.7 N≈40.52 Nf_k = \mu_k F_N = 0.280 \times 144.7\text{ N} \approx 40.52\text{ N}

    Your formula and calculation method for kinetic friction were completely correct, but the result was affected by the incorrect normal force from Step 1.

  3. Step 3

    FTcos⁡(25.0∘)−fk=max  ⟹  67.97−58.27=18.0ax  ⟹  9.70=18.0ax  ⟹  ax=0.539 m/s2F_T \cos(25.0^\circ) - f_k = m a_x \implies 67.97 - 58.27 = 18.0 a_x \implies 9.70 = 18.0 a_x \implies a_x = 0.539\text{ m/s}^2

    Correct

    ax=FTcos⁡(25.0∘)−fkm=67.97 N−40.52 N18.0 kg=27.45 N18.0 kg≈1.52 m/s2a_x = \frac{F_T \cos(25.0^\circ) - f_k}{m} = \frac{67.97\text{ N} - 40.52\text{ N}}{18.0\text{ kg}} = \frac{27.45\text{ N}}{18.0\text{ kg}} \approx 1.52\text{ m/s}^2

    Your setup of Newton's Second Law along the xx-axis was completely correct, but the resulting acceleration was lower than expected due to the overestimated friction force propagated from Step 2.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly resolved the tension force into its horizontal and vertical trigonometric components.

You correctly applied the kinetic friction formula fk=μkFNf_k = \mu_k F_N.

You correctly set up Newton's Second Law along the horizontal axis as ΣFx=FTcos⁡θ−fk=max\Sigma F_x = F_T \cos\theta - f_k = m a_x.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Sign Error in Vertical Equilibrium

You added the upward vertical component of tension to the crate's weight instead of subtracting it when solving for the normal force.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing the sign of force components in vertical equilibrium by treating an upward pull as pressing into the floor rather than lifting off it.

REASONING PATH
Your ACEpath teacher’s suggested approach
Equilibrium Sign Convention
  • Along the vertical axis, forces pointing upward (+y+y) and forces pointing downward (−y-y) satisfy ΣFy=FN+FTy−mg=0\Sigma F_y = F_N + F_{Ty} - mg = 0 when there is no vertical motion.

  • Always sketch arrows on a free-body diagram first: upward forces get positive signs and downward forces get negative signs before solving algebraically for FNF_N.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Apply vertical equilibrium with upward forces positive: ΣFy=FN+FTsin⁡(25.0∘)−mg=0\Sigma F_y = F_N + F_T \sin(25.0^\circ) - mg = 0.

  2. Solve for the normal force: FN=mg−FTsin⁡(25.0∘)=(18.0)(9.80)−(75.0)sin⁡(25.0∘)=176.4−31.70=144.7 N≈145 NF_N = mg - F_T \sin(25.0^\circ) = (18.0)(9.80) - (75.0)\sin(25.0^\circ) = 176.4 - 31.70 = 144.7\text{ N} \approx 145\text{ N}.

  3. Recalculate kinetic friction with the corrected normal force: fk=μkFN=0.280×144.7 N≈40.52 Nf_k = \mu_k F_N = 0.280 \times 144.7\text{ N} \approx 40.52\text{ N}.

  4. Solve for horizontal acceleration: ax=FTcos⁡(25.0∘)−fkm=67.97 N−40.52 N18.0 kg=27.45 N18.0 kg≈1.52 m/s2a_x = \frac{F_T \cos(25.0^\circ) - f_k}{m} = \frac{67.97\text{ N} - 40.52\text{ N}}{18.0\text{ kg}} = \frac{27.45\text{ N}}{18.0\text{ kg}} \approx 1.52\text{ m/s}^2.

Final answer

FN=145 NF_N = 145\text{ N}, ax=1.52 m/s2a_x = 1.52\text{ m/s}^2

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the vertical force balance on a free-body diagram whenever an applied force is angled.

  • Practice checking whether an external force relieves the floor (FN<mgF_N < mg) or presses into the floor (FN>mgF_N > mg).

  • Work through the flashcards and practice problems below to master normal force calculations with angled forces.

OverviewACEpath Teacher's Diagnosis

03 The student swaps the sine and cosine trigonometric functions for the force components, using cosine for the vertical component and sine for the horizontal component.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    FN=m∗g−FT∗cos⁡(25.0∘)  ⟹  FN=18.0∗9.80−75.0∗cos⁡(25.0∘)  ⟹  FN=176.4−67.97=108.43 NF_N = m * g - F_T * \cos(25.0^\circ) \implies F_N = 18.0 * 9.80 - 75.0 * \cos(25.0^\circ) \implies F_N = 176.4 - 67.97 = 108.43\text{ N}

    Correct

    ΣFy=FN+FTsin⁡(25.0∘)−mg=0  ⟹  FN=mg−FTsin⁡(25.0∘)=176.4 N−31.70 N≈145 N\Sigma F_y = F_N + F_T \sin(25.0^\circ) - mg = 0 \implies F_N = mg - F_T \sin(25.0^\circ) = 176.4\text{ N} - 31.70\text{ N} \approx 145\text{ N}

    Because the pulling angle θ=25.0∘\theta = 25.0^\circ is measured relative to the horizontal floor, the side opposite to the angle is the vertical side. Therefore, the vertical component of tension is FTy=FTsin⁡(25.0∘)F_{Ty} = F_T \sin(25.0^\circ), not FTcos⁡(25.0∘)F_T \cos(25.0^\circ).

  2. Step 2

    fk=μk∗FN=0.280∗108.43=30.36 Nf_k = \mu_k * F_N = 0.280 * 108.43 = 30.36\text{ N}

    Correct

    fk=μkFN=0.280⋅144.70 N≈40.52 Nf_k = \mu_k F_N = 0.280 \cdot 144.70\text{ N} \approx 40.52\text{ N}

    Your application of fk=μkFNf_k = \mu_k F_N is conceptually correct, but the resulting numerical value is affected by your earlier calculation of FNF_N.

  3. Step 3

    FT∗sin⁡(25.0∘)−fk=m∗ax  ⟹  75.0∗sin⁡(25.0∘)−30.36=18.0∗ax  ⟹  31.70−30.36=18.0∗ax  ⟹  1.34=18.0∗ax  ⟹  ax=0.0744 m/s2F_T * \sin(25.0^\circ) - f_k = m * a_x \implies 75.0 * \sin(25.0^\circ) - 30.36 = 18.0 * a_x \implies 31.70 - 30.36 = 18.0 * a_x \implies 1.34 = 18.0 * a_x \implies a_x = 0.0744\text{ m/s}^2

    Correct

    ΣFx=FTcos⁡(25.0∘)−fk=max  ⟹  ax=75.0cos⁡(25.0∘)−40.5218.0≈1.52 m/s2\Sigma F_x = F_T \cos(25.0^\circ) - f_k = m a_x \implies a_x = \frac{75.0 \cos(25.0^\circ) - 40.52}{18.0} \approx 1.52\text{ m/s}^2

    The horizontal component of the tension is adjacent to the 25.0∘25.0^\circ angle, which requires the cosine function (FTx=FTcos⁡(25.0∘)F_{Tx} = F_T \cos(25.0^\circ)) rather than sine.

WHAT YOU DID WELL
Compliments from Your Teacher

You recognized that the upward component of tension reduces the normal force exerted by the floor.

You correctly used the kinetic friction relation fk=μkFNf_k = \mu_k F_N.

You properly formulated Newton's second law along the horizontal axis as net force equals mass times acceleration.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Trigonometric Component Swap

You swapped the sine and cosine functions when projecting the tension force vector onto the horizontal and vertical coordinate axes.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Associating vertical components generally with cosine or confusing opposite and adjacent legs in the right triangle formed by the vector and the reference axis.

REASONING PATH
Your ACEpath teacher’s suggested approach
Reference Triangle Rule
  • For an angle θ\theta measured relative to the horizontal, the adjacent leg along the horizontal uses cos⁡θ\cos\theta and the opposite leg along the vertical uses sin⁡θ\sin\theta.

  • Sketch a right triangle around the angled force vector with legs along the coordinate axes before writing algebraic expressions.

Extreme-Angle Sanity Check
  • As θ→0∘\theta \to 0^\circ, the force becomes purely horizontal (Fx→FTF_x \to F_T, Fy→0F_y \to 0).

  • Verify that your horizontal component uses cos⁡θ\cos\theta because cos⁡(0∘)=1\cos(0^\circ) = 1, and your vertical component uses sin⁡θ\sin\theta because sin⁡(0∘)=0\sin(0^\circ) = 0.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Calculate vertical component: FTy=75.0 N⋅sin⁡(25.0∘)≈31.70 NF_{Ty} = 75.0\text{ N} \cdot \sin(25.0^\circ) \approx 31.70\text{ N}.

  2. Solve for the normal force: FN=mg−FTy=(18.0 kg)(9.80 m/s2)−31.70 N=176.4 N−31.70 N=144.70 N≈145 NF_N = mg - F_{Ty} = (18.0\text{ kg})(9.80\text{ m/s}^2) - 31.70\text{ N} = 176.4\text{ N} - 31.70\text{ N} = 144.70\text{ N} \approx 145\text{ N}.

  3. Determine the kinetic friction force: fk=μkFN=0.280⋅144.70 N≈40.52 Nf_k = \mu_k F_N = 0.280 \cdot 144.70\text{ N} \approx 40.52\text{ N}.

  4. Calculate horizontal component: FTx=75.0 N⋅cos⁡(25.0∘)≈67.97 NF_{Tx} = 75.0\text{ N} \cdot \cos(25.0^\circ) \approx 67.97\text{ N}.

  5. Apply Newton's second law horizontally: ax=FTx−fkm=67.97 N−40.52 N18.0 kg=27.45 N18.0 kg≈1.52 m/s2a_x = \frac{F_{Tx} - f_k}{m} = \frac{67.97\text{ N} - 40.52\text{ N}}{18.0\text{ kg}} = \frac{27.45\text{ N}}{18.0\text{ kg}} \approx 1.52\text{ m/s}^2.

Final answer

FN=145 NF_N = 145\text{ N}, ax=1.52 m/s2a_x = 1.52\text{ m/s}^2

NEXT STEPS
Final Takeaways from Your Teacher
  • Review vector resolution by drawing right triangles and labeling opposite and adjacent sides.

  • Perform quick limiting-case checks (testing θ=0∘\theta = 0^\circ and θ=90∘\theta = 90^\circ) whenever decomposing forces.

  • Practice solving friction problems where forces act at an angle above or below the horizontal.

Lock it in

Similar question

01

A 10.0 kg10.0\text{ kg} box is pulled across a flat floor by a force of 40.0 N40.0\text{ N} directed at 30.0∘30.0^\circ above the horizontal. If g=9.80 m/s2g = 9.80\text{ m/s}^2, find the magnitude of the normal force FNF_N.

Answer

FN=78.0 NF_N = 78.0\text{ N}. From vertical equilibrium: ΣFy=FN+Fsin⁡(30.0∘)−mg=0  ⟹  FN=(10.0)(9.80)−40.0(0.500)=98.0−20.0=78.0 N\Sigma F_y = F_N + F\sin(30.0^\circ) - mg = 0 \implies F_N = (10.0)(9.80) - 40.0(0.500) = 98.0 - 20.0 = 78.0\text{ N}.

02

A lawnmower of mass 15.0 kg15.0\text{ kg} is pushed across a level lawn with a force of 60.0 N60.0\text{ N} directed downward along the handle at an angle of 37.0∘37.0^\circ below the horizontal. Assuming g=9.80 m/s2g = 9.80\text{ m/s}^2, determine the normal force exerted by the ground.

Answer

FN=183 NF_N = 183\text{ N}. Downward components add to the weight: ΣFy=FN−mg−Fsin⁡(37.0∘)=0  ⟹  FN=(15.0)(9.80)+60.0sin⁡(37.0∘)=147+36.1=183.1 N≈183 N\Sigma F_y = F_N - mg - F\sin(37.0^\circ) = 0 \implies F_N = (15.0)(9.80) + 60.0\sin(37.0^\circ) = 147 + 36.1 = 183.1\text{ N} \approx 183\text{ N}.

03

A 25.0 kg25.0\text{ kg} crate is pulled across a rough horizontal floor (μk=0.350\mu_k = 0.350) by a tension force FT=110 NF_T = 110\text{ N} directed at an angle θ=20.0∘\theta = 20.0^\circ above the horizontal. Taking g=9.80 m/s2g = 9.80\text{ m/s}^2, calculate the magnitude of the kinetic friction force fkf_k and the horizontal acceleration axa_x.

Answer

fk=72.6 Nf_k = 72.6\text{ N}, ax=1.23 m/s2a_x = 1.23\text{ m/s}^2. Vertical balance gives FN=mg−FTsin⁡(20.0∘)=(25.0)(9.80)−110sin⁡(20.0∘)=245−37.62=207.38 NF_N = mg - F_T\sin(20.0^\circ) = (25.0)(9.80) - 110\sin(20.0^\circ) = 245 - 37.62 = 207.38\text{ N}. Kinetic friction is fk=μkFN=(0.350)(207.38 N)≈72.6 Nf_k = \mu_k F_N = (0.350)(207.38\text{ N}) \approx 72.6\text{ N}. Then horizontal acceleration is ax=FTcos⁡(20.0∘)−fkm=103.36−72.5825.0=30.7825.0≈1.23 m/s2a_x = \frac{F_T\cos(20.0^\circ) - f_k}{m} = \frac{103.36 - 72.58}{25.0} = \frac{30.78}{25.0} \approx 1.23\text{ m/s}^2.

Loading workspace…