Resources

A high-speed grinding wheel has an outer diameter of 24.0 cm24.0\text{ cm} (radius r=12.0 cmr = 12.0\text{ cm}). When grinding a steel rod, sparks fly tangentially off the rim at a linear speed of v=45.2 m/sv = 45.2\text{ m/s}. Reverse-engineer the operating state of the motor driving the wheel: calculate (a) the angular speed ω\omega of the grinding wheel in rad/s\text{rad/s}, and (b) the motor shaft rotation rate in revolutions per minute (rpm\text{rpm}). Round all values to three significant figures.

Answer and steps

Final answer

(a) ω=377 rad/s\omega = 377\text{ rad/s}; (b) N=3.60×103 rpmN = 3.60 \times 10^3\text{ rpm}

Steps

Part (a): Calculate the Angular Speed ω\omega in rad/s\text{rad/s}

  1. Identify the relationship between linear speed and angular speed: Every point on the rim of a rotating wheel moves tangentially with a linear speed vv related to its angular speed ω\omega and radius rr by the formula: v=rωv = r\omega
  2. Convert units to SI base units: The radius is given as: r=12.0 cm=0.120 mr = 12.0\text{ cm} = 0.120\text{ m} The tangential speed of the sparks leaving the rim is: v=45.2 m/sv = 45.2\text{ m/s}
  3. Solve for ω\omega: ω=vr=45.2 m/s0.120 m≈376.67 rad/s\omega = \frac{v}{r} = \frac{45.2\text{ m/s}}{0.120\text{ m}} \approx 376.67\text{ rad/s}

    Rounding to three significant figures gives: ω=377 rad/s\omega = 377\text{ rad/s}


Part (b): Calculate the Rotation Rate in rpm\text{rpm}

  1. Relate angular speed (rad/s\text{rad/s}) to rotational speed in revolutions per minute (rpm\text{rpm}):

    • One full revolution equals 2π radians2\pi\text{ radians}.
    • One minute equals 60 seconds60\text{ seconds}.

    Therefore, the conversion formula is: N=ω⋅60 s/min2π rad/revN = \omega \cdot \frac{60\text{ s/min}}{2\pi\text{ rad/rev}}

  2. Compute the rotational speed NN: Using the unrounded value of ω=45.20.120 rad/s\omega = \frac{45.2}{0.120}\text{ rad/s}: N=376.67×602π≈226006.283185≈3596.94 rpmN = \frac{376.67 \times 60}{2\pi} \approx \frac{22600}{6.283185} \approx 3596.94\text{ rpm}

    Rounding to three significant figures and expressing in scientific notation: N=3.60×103 rpmN = 3.60 \times 10^3\text{ rpm}

Common Pitfall: Be sure to convert the radius from centimeters to meters before calculating ω\omega. Using r=12.0 cmr = 12.0\text{ cm} directly would result in an angular speed off by a factor of 100100.

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student forgets to convert the radius from centimeters to meters, resulting in an angular speed that is two orders of magnitude too small.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    ω=vr  ⟹  ω=45.212.0  ⟹  ω=3.77 rad/s\omega = \frac{v}{r} \implies \omega = \frac{45.2}{12.0} \implies \omega = 3.77\text{ rad/s}

    Correct

    r=12.0 cm=0.120 m  ⟹  ω=vr=45.2 m/s0.120 m≈377 rad/sr = 12.0\text{ cm} = 0.120\text{ m} \implies \omega = \frac{v}{r} = \frac{45.2\text{ m/s}}{0.120\text{ m}} \approx 377\text{ rad/s}

    You correctly set up the formula ω=vr\omega = \frac{v}{r}, but you substituted r=12.0 cmr = 12.0\text{ cm} without converting it into standard SI units (meters). Because vv is in m/s\text{m/s}, rr must be in m\text{m} (0.120 m0.120\text{ m}), which makes your calculated angular speed 100 times too small.

  2. Step 2

    N=ω×602π  ⟹  N=3.77×602π  ⟹  N=36.0 rpmN = \frac{\omega \times 60}{2\pi} \implies N = \frac{3.77 \times 60}{2\pi} \implies N = 36.0\text{ rpm}

    Correct

    N=ω×602π=376.67×602π≈3.60×103 rpmN = \frac{\omega \times 60}{2\pi} = \frac{376.67 \times 60}{2\pi} \approx 3.60 \times 10^3\text{ rpm}

    Your unit conversion formula between rad/s\text{rad/s} and rpm\text{rpm} is completely correct. However, substituting your earlier value of ω=3.77 rad/s\omega = 3.77\text{ rad/s} carried the factor-of-100 error through to your final rotation rate.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly used the relationship v=rωv = r\omega connecting tangential linear speed and angular speed.

You correctly set up the unit conversion between radians per second and revolutions per minute using 602π\frac{60}{2\pi}.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Missing SI unit conversion for radius

You divided linear speed in meters per second by a radius given in centimeters instead of converting centimeters to meters first.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Forgetting to verify that all length dimensions share the same base unit before using kinematic formulas causes an error by a factor of 100 (10210^2).

REASONING PATH
Your ACEpath teacher’s suggested approach
Match Length Units Across Quantities
  • In v=rωv = r\omega, linear speed is in m/s\text{m/s} and angular speed is in rad/s\text{rad/s}, which requires radius to be in meters (m\text{m}).

  • Convert any given centimeter values to meters by dividing by 100100 (12.0 cm=0.120 m12.0\text{ cm} = 0.120\text{ m}) before substituting into the equation.

Reality-Check Angular Speeds
  • A high-speed grinding tool spins thousands of times per minute; an angular speed of 3.77 rad/s3.77\text{ rad/s} is roughly half a revolution per second, which is far too slow for grinding.

  • Check whether the calculated rotation speed matches the physical scenario before finalizing the answer.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Convert the radius to SI base units: r=12.0 cm=0.120 mr = 12.0\text{ cm} = 0.120\text{ m}.

  2. Calculate the angular speed: ω=45.2 m/s0.120 m=376.67 rad/s≈377 rad/s\omega = \frac{45.2\text{ m/s}}{0.120\text{ m}} = 376.67\text{ rad/s} \approx 377\text{ rad/s}.

  3. Convert angular speed to revolutions per minute: N=ω×602π=376.67×602π≈3.60×103 rpmN = \frac{\omega \times 60}{2\pi} = \frac{376.67 \times 60}{2\pi} \approx 3.60 \times 10^3\text{ rpm}.

Final answer

(a) ω=377 rad/s\omega = 377\text{ rad/s}; (b) N=3.60×103 rpmN = 3.60 \times 10^3\text{ rpm}

NEXT STEPS
Final Takeaways from Your Teacher
  • Always write down the units alongside each numerical value when substituting into physics formulas to catch unit mismatches immediately.

  • Practice converting common non-SI unit prefixes (such as centi- and milli-) to base SI units before performing calculations.

OverviewACEpath Teacher's Diagnosis

02 The student uses the diameter instead of the radius in the linear-to-angular velocity relationship.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    r=0.240 mr = 0.240\text{ m}

    Correct

    r=d2=24.0 cm2=12.0 cm=0.120 mr = \frac{d}{2} = \frac{24.0\text{ cm}}{2} = 12.0\text{ cm} = 0.120\text{ m}

    You substituted the outer diameter (24.0 cm24.0\text{ cm}) directly as the radius rr. The radius is half of the diameter, so r=0.120 mr = 0.120\text{ m}.

  2. Step 2

    ω=vr=45.20.240  ⟹  ω=188 rad/s\omega = \frac{v}{r} = \frac{45.2}{0.240} \implies \omega = 188\text{ rad/s}

    Correct

    ω=vr=45.2 m/s0.120 m≈377 rad/s\omega = \frac{v}{r} = \frac{45.2\text{ m/s}}{0.120\text{ m}} \approx 377\text{ rad/s}

    You correctly used the relationship ω=vr\omega = \frac{v}{r} and computed the arithmetic accurately for your value of rr, but the result was halved due to the incorrect radius in Step 1.

  3. Step 3

    N=ω×602π  ⟹  N=188.3×602π  ⟹  N=1800 rpmN = \omega \times \frac{60}{2\pi} \implies N = 188.3 \times \frac{60}{2\pi} \implies N = 1800\text{ rpm}

    Correct

    N=376.67×602π≈3.60×103 rpmN = 376.67 \times \frac{60}{2\pi} \approx 3.60 \times 10^3\text{ rpm}

    You set up the unit conversion from rad/s\text{rad/s} to rpm\text{rpm} correctly, but the result inherits the halved value from your previous calculation of ω\omega.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified and applied the linear-to-angular speed relation v=rωv = r\omega.

You converted centimeters to meters accurately when writing down the value in SI base units.

You correctly converted angular speed from rad/s\text{rad/s} to revolutions per minute using the factor 602π\frac{60}{2\pi}.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Radius-Diameter Confusion

You labeled the diameter of 24.0 cm24.0\text{ cm} as the radius rr.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You overlooked the distinction between diameter (dd) and radius (rr) when extracting the given physical quantities from the problem statement.

REASONING PATH
Your ACEpath teacher’s suggested approach
Check Given Dimensions
  • The kinematic formula v=rωv = r\omega requires the radius rr, which is the distance from the rotation axis to the point of interest, not the full diameter (r=d/2r = d/2).

  • Always highlight whether the problem specifies diameter or radius before writing down rr.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Identify the wheel radius: r=24.0 cm2=12.0 cm=0.120 mr = \frac{24.0\text{ cm}}{2} = 12.0\text{ cm} = 0.120\text{ m}.

  2. Calculate angular speed: ω=vr=45.2 m/s0.120 m≈376.67 rad/s≈377 rad/s\omega = \frac{v}{r} = \frac{45.2\text{ m/s}}{0.120\text{ m}} \approx 376.67\text{ rad/s} \approx 377\text{ rad/s}.

  3. Convert to rotational speed in rpm\text{rpm}: N=ω⋅602π=376.67⋅602π≈3.60×103 rpmN = \omega \cdot \frac{60}{2\pi} = 376.67 \cdot \frac{60}{2\pi} \approx 3.60 \times 10^3\text{ rpm}.

Final answer

(a) ω=377 rad/s\omega = 377\text{ rad/s}; (b) N=3.60×103 rpmN = 3.60 \times 10^3\text{ rpm}

NEXT STEPS
Final Takeaways from Your Teacher
  • Double-check every circular dimension given in a problem statement to confirm whether diameter dd or radius rr is provided.

  • Keep intermediate numbers unrounded in your calculator before rounding to the requested three significant figures at the very end.

OverviewACEpath Teacher's Diagnosis

03 The student multiplies by 2π instead of dividing by 2π when converting radians per second to revolutions per minute.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    r=0.120 m  ⟹  ω=vr=45.20.120  ⟹  ω=377 rad/sr = 0.120\text{ m} \implies \omega = \frac{v}{r} = \frac{45.2}{0.120} \implies \omega = 377\text{ rad/s}

  2. Step 2

    N=ω×2π×60  ⟹  N=376.7×2π×60  ⟹  N=142000 rpmN = \omega \times 2\pi \times 60 \implies N = 376.7 \times 2\pi \times 60 \implies N = 142000\text{ rpm}

    Correct

    N=ω⋅1 rev2π rad⋅60 s1 min=376.7×602π≈3.60×103 rpmN = \omega \cdot \frac{1\text{ rev}}{2\pi\text{ rad}} \cdot \frac{60\text{ s}}{1\text{ min}} = \frac{376.7 \times 60}{2\pi} \approx 3.60 \times 10^3\text{ rpm}

    When converting from radians to revolutions, you must divide by 2π rad/rev2\pi\text{ rad/rev} because one complete revolution contains 2π2\pi radians.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly converted the radius of 12.0 cm12.0\text{ cm} into SI units as 0.120 m0.120\text{ m}.

You correctly recalled and applied the relationship between tangential speed and angular speed, v=rωv = r\omega.

You recognized that converting per second to per minute requires multiplying by 6060.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Inverted Conversion Factor

You multiplied by 2π2\pi instead of dividing by 2π2\pi when converting radians to revolutions.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusion over dimensional analysis and unit cancellation during angle conversion. Because 1 rev=2π rad1\text{ rev} = 2\pi\text{ rad}, converting an angle or angular rate from radians to revolutions requires dividing by 2π rad/rev2\pi\text{ rad/rev} so that the 'rad' units cancel out in the numerator and denominator.

REASONING PATH
Your ACEpath teacher’s suggested approach
Unit Cancellation Check
  • Set up conversion ratios so that existing units cancel algebraically: rad/s×1 rev2π rad×60 s1 min=rev/min\text{rad/s} \times \frac{1\text{ rev}}{2\pi\text{ rad}} \times \frac{60\text{ s}}{1\text{ min}} = \text{rev/min}.

  • Always write the unit labels explicitly next to each conversion factor before multiplying or dividing.

Magnitude Sanity Check
  • One revolution is roughly 6.28 radians6.28\text{ radians}, so the count in revolutions must always be smaller than the count in radians over the same time interval.

  • Check whether your value in revolutions per second is smaller than your value in radians per second by a factor of about 66.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Write out the unit conversion factors explicitly: N=376.7 rad/s×1 rev2π rad×60 s1 minN = 376.7\text{ rad/s} \times \frac{1\text{ rev}}{2\pi\text{ rad}} \times \frac{60\text{ s}}{1\text{ min}}.

  2. Group the numerical values: N=376.7×602πN = \frac{376.7 \times 60}{2\pi}.

  3. Evaluate the numerator and denominator: N=226026.2832≈3597 rpmN = \frac{22602}{6.2832} \approx 3597\text{ rpm}.

Final answer

(a) ω=377 rad/s\omega = 377\text{ rad/s}; (b) N=3.60×103 rpmN = 3.60 \times 10^3\text{ rpm}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review how unit cancellation works with dimensional analysis for angular quantities.

  • Practice converting back and forth between rad/s\text{rad/s} and rpm\text{rpm} using explicit conversion fractions.

Lock it in

Similar question

01

A circular saw blade has a radius of r=15.0 cmr = 15.0\text{ cm}. A tooth on the outer edge moves at a tangential speed of v=30.0 m/sv = 30.0\text{ m/s}. What is the angular speed ω\omega of the saw blade in rad/s\text{rad/s}?

Answer

r=15.0 cm=0.150 mr = 15.0\text{ cm} = 0.150\text{ m}. Using ω=vr=30.0 m/s0.150 m=200 rad/s\omega = \frac{v}{r} = \frac{30.0\text{ m/s}}{0.150\text{ m}} = 200\text{ rad/s}.

02

A compact disc rotates at 500 rpm500\text{ rpm}. What is the linear speed vv (in m/s\text{m/s}) of a point located at radius r=4.00 cmr = 4.00\text{ cm} from the center? Round to three significant figures.

Answer

Convert rotation rate to angular speed: ω=500×2π60≈52.36 rad/s\omega = 500 \times \frac{2\pi}{60} \approx 52.36\text{ rad/s}. Convert radius: r=4.00 cm=0.0400 mr = 4.00\text{ cm} = 0.0400\text{ m}. Then v=rω=0.0400 m×52.36 rad/s≈2.09 m/sv = r\omega = 0.0400\text{ m} \times 52.36\text{ rad/s} \approx 2.09\text{ m/s}.

03

An ultracentrifuge rotor has a radius of 8.00 cm8.00\text{ cm}. During operation, a test tube at the rim experiences a tangential speed of 418.9 m/s418.9\text{ m/s}. Find (a) the angular speed ω\omega in rad/s\text{rad/s}, and (b) the rotation rate in rpm\text{rpm}. Express both to three significant figures.

Answer

(a) r=0.0800 mr = 0.0800\text{ m}, so ω=vr=418.9 m/s0.0800 m≈5.24×103 rad/s\omega = \frac{v}{r} = \frac{418.9\text{ m/s}}{0.0800\text{ m}} \approx 5.24 \times 10^3\text{ rad/s}. (b) N=ω×602π=5236.25×602π≈5.00×104 rpmN = \frac{\omega \times 60}{2\pi} = \frac{5236.25 \times 60}{2\pi} \approx 5.00 \times 10^4\text{ rpm}.

Loading workspace…