Resources

A diesel test engine achieves a thermal efficiency of η=42.0%\eta = 42.0\%. If the engine expels 870 J870\text{ J} of heat to its exhaust system during each power stroke, calculate the quantity of heat QHQ_H absorbed from the combustion process per cycle.

Answer and steps

Final answer

QH=1500 JQ_H = 1500\text{ J}

Steps

01

Identify the relationship between efficiency, heat absorbed, and heat expelled

For any cyclic heat engine, the energy absorbed from the high-temperature reservoir (QHQ_H) is converted into useful work output (WW) and rejected heat expelled to the low-temperature exhaust (QCQ_C):

QH=W+QC  ⟹  W=QH−QCQ_H = W + Q_C \implies W = Q_H - Q_C

The thermal efficiency η\eta is defined as the ratio of the net work produced to the total heat input:

η=WQH=QH−QCQH=1−QCQH\eta = \frac{W}{Q_H} = \frac{Q_H - Q_C}{Q_H} = 1 - \frac{Q_C}{Q_H}


02

Rearrange the formula to solve for QHQ_H

Isolate the heat absorbed, QHQ_H:

QCQH=1−η\frac{Q_C}{Q_H} = 1 - \eta

QH=QC1−ηQ_H = \frac{Q_C}{1 - \eta}


03

Substitute the given values

Convert the efficiency percentage into a decimal:

  • η=42.0%=0.420\eta = 42.0\% = 0.420
  • QC=870 JQ_C = 870\text{ J}

Calculate the fraction of heat expelled:

1−η=1−0.420=0.5801 - \eta = 1 - 0.420 = 0.580

Now, evaluate QHQ_H:

QH=870 J0.580=1500 JQ_H = \frac{870\text{ J}}{0.580} = 1500\text{ J}

Common Pitfall: Be careful not to confuse heat expelled (QCQ_C) with work output (WW). Calculating QHQ_H as QCη\frac{Q_C}{\eta} is incorrect because efficiency measures WQH\frac{W}{Q_H}, not QCQH\frac{Q_C}{Q_H}.

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student confuses the expelled heat with the work output and uses the formula η = QC/QH, leading to an incorrect absorbed heat of approximately 2071 J.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    η=QCQH  ⟹  QH=QCη\eta = \frac{Q_C}{Q_H} \implies Q_H = \frac{Q_C}{\eta}

    Correct

    η=1−QCQH  ⟹  QH=QC1−η\eta = 1 - \frac{Q_C}{Q_H} \implies Q_H = \frac{Q_C}{1 - \eta}

    Thermal efficiency represents the fraction of heat turned into useful work, η=WQH=QH−QCQH=1−QCQH\eta = \frac{W}{Q_H} = \frac{Q_H - Q_C}{Q_H} = 1 - \frac{Q_C}{Q_H}. Setting η=QCQH\eta = \frac{Q_C}{Q_H} confuses the expelled waste heat with useful work.

  2. Step 2

    QH=8700.420Q_H = \frac{870}{0.420}

    Correct

    QH=8701−0.420=8700.580Q_H = \frac{870}{1 - 0.420} = \frac{870}{0.580}

    You substituted the values correctly into your formula, but the denominator is affected by the incorrect definition in Step 1.

  3. Step 3

    QH=2071 JQ_H = 2071\text{ J}

    Correct

    QH=1500 JQ_H = 1500\text{ J}

    Your arithmetic was carried out correctly for your expression, but the resulting numerical value is incorrect due to the initial formula error.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly recognized that 870 J870\text{ J} corresponds to the exhaust heat QCQ_C.

You properly converted the percentage efficiency 42.0%42.0\% into the decimal 0.4200.420.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Thermal efficiency definition error

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated thermal efficiency as the ratio of expelled heat to heat absorbed (QCQH\frac{Q_C}{Q_H}) instead of the ratio of useful work output to heat absorbed (WQH=1−QCQH\frac{W}{Q_H} = 1 - \frac{Q_C}{Q_H}).

REASONING PATH
Your ACEpath teacher’s suggested approach
Define efficiency by useful output
  • Efficiency is always η=useful outputtotal input=WQH\eta = \frac{\text{useful output}}{\text{total input}} = \frac{W}{Q_H}.

  • Express work in terms of heat reservoirs using energy conservation: W=QH−QCW = Q_H - Q_C.

Relate heat rejected to efficiency
  • The fraction of input heat lost as exhaust is QCQH=1−η\frac{Q_C}{Q_H} = 1 - \eta.

  • When QCQ_C is given, isolate QHQ_H using QH=QC1−ηQ_H = \frac{Q_C}{1 - \eta}.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Use the first law of thermodynamics for a cyclic engine: W=QH−QCW = Q_H - Q_C.

  2. Write thermal efficiency in terms of heats: η=QH−QCQH=1−QCQH\eta = \frac{Q_H - Q_C}{Q_H} = 1 - \frac{Q_C}{Q_H}.

  3. Rearrange to solve for input heat: QH=QC1−ηQ_H = \frac{Q_C}{1 - \eta}.

  4. Substitute QC=870 JQ_C = 870\text{ J} and η=0.420\eta = 0.420: QH=870 J1−0.420=870 J0.580=1500 JQ_H = \frac{870\text{ J}}{1 - 0.420} = \frac{870\text{ J}}{0.580} = 1500\text{ J}.

Final answer

QH=1500 JQ_H = 1500\text{ J}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the energy flow diagram of a heat engine to keep WW, QHQ_H, and QCQ_C clearly separated.

  • Practice deriving QH=QC1−ηQ_H = \frac{Q_C}{1 - \eta} and W=η1−ηQCW = \frac{\eta}{1 - \eta}Q_C directly from conservation of energy.

OverviewACEpath Teacher's Diagnosis

02 The student misapplies the efficiency formula as QH = QC * (1 - η) instead of dividing, calculating an absorbed heat of 504.6 J that is incorrectly smaller than the expelled heat.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    QC=QH1−η  ⟹  QH=QC⋅(1−η)Q_C = \frac{Q_H}{1-\eta} \implies Q_H = Q_C \cdot (1-\eta)

    Correct

    η=1−QCQH  ⟹  QCQH=1−η  ⟹  QH=QC1−η\eta = 1 - \frac{Q_C}{Q_H} \implies \frac{Q_C}{Q_H} = 1 - \eta \implies Q_H = \frac{Q_C}{1-\eta}

    You inverted the fraction when relating thermal efficiency to heat transfer. Starting from η=1−QCQH\eta = 1 - \frac{Q_C}{Q_H}, isolating the ratio gives QCQH=1−η\frac{Q_C}{Q_H} = 1 - \eta. Taking the reciprocal or solving for QHQ_H requires dividing QCQ_C by (1−η)(1 - \eta), not multiplying.

  2. Step 2

    QH=870⋅(1−0.420)  ⟹  QH=870⋅0.580Q_H = 870 \cdot (1-0.420) \implies Q_H = 870 \cdot 0.580

    Correct

    QH=870 J1−0.420=870 J0.580Q_H = \frac{870\text{ J}}{1 - 0.420} = \frac{870\text{ J}}{0.580}

    Your numerical substitution and subtraction were carried out correctly, but they followed the inverted formula from Step 1.

  3. Step 3

    QH=504.6 JQ_H = 504.6\text{ J}

    Correct

    QH=1500 JQ_H = 1500\text{ J}

    Your arithmetic was accurate based on your setup, but propagating the earlier algebraic error led to a value smaller than the expelled heat.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly expressed the thermal efficiency η=42.0%\eta = 42.0\% as the decimal 0.4200.420.

You calculated 1−η=0.5801 - \eta = 0.580 without error.

You performed your multiplications and labeled your unit cleanly.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Formula rearrangement inversion

You set QH=QC⋅(1−η)Q_H = Q_C \cdot (1-\eta) rather than dividing QCQ_C by (1−η)(1-\eta).

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated the exhaust fraction (1−η)(1 - \eta) as a multiplier on QCQ_C instead of recognizing that QCQ_C itself is the remaining fraction of the total heat input: QC=(1−η)QHQ_C = (1 - \eta)Q_H. Since 0<1−η<10 < 1 - \eta < 1, multiplying by (1−η)(1 - \eta) resulted in an input heat smaller than the exhaust heat, which violates the first law of thermodynamics (QH=W+QCQ_H = W + Q_C).

REASONING PATH
Your ACEpath teacher’s suggested approach
Energy conservation sanity check
  • For any heat engine, QH=W+QCQ_H = W + Q_C. Therefore, QHQ_H must always be strictly greater than both WW and QCQ_C.

  • Whenever you calculate QHQ_H, verify immediately that QH>QCQ_H > Q_C. If your result is smaller than the expelled heat, check whether you multiplied instead of dividing.

Isolating variables from fractions
  • When AB=C\frac{A}{B} = C, multiplying by BB yields A=B⋅CA = B \cdot C, which means B=ACB = \frac{A}{C}.

  • Set QCQH=1−η\frac{Q_C}{Q_H} = 1 - \eta, then solve step-by-step: multiply by QHQ_H to get QC=QH(1−η)Q_C = Q_H(1-\eta), and divide by (1−η)(1-\eta) to obtain QH=QC1−ηQ_H = \frac{Q_C}{1-\eta}.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Write the definition of thermal efficiency: η=1−QCQH\eta = 1 - \frac{Q_C}{Q_H}.

  2. Rearrange to isolate QHQ_H: QCQH=1−η  ⟹  QH=QC1−η\frac{Q_C}{Q_H} = 1 - \eta \implies Q_H = \frac{Q_C}{1 - \eta}.

  3. Substitute the given quantities: QH=870 J1−0.420=870 J0.580Q_H = \frac{870\text{ J}}{1 - 0.420} = \frac{870\text{ J}}{0.580}.

  4. Evaluate the quotient: QH=1500 JQ_H = 1500\text{ J}.

Final answer

QH=1500 JQ_H = 1500\text{ J}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the energy balance diagram of a heat engine to anchor the fact that total heat input (QHQ_H) splits into useful work (WW) and rejected heat (QCQ_C).

  • Practice rearranging three-variable fractional formulas like ab=c\frac{a}{b} = c to ensure the denominator is isolated by division.

  • Solve follow-up problems where either QCQ_C, QHQ_H, or WW is unknown given efficiency.

OverviewACEpath Teacher's Diagnosis

03 The student uses the work output definition W = η * QC instead of relating efficiency to the heat input QH, then adds W to QC to obtain QH = 1235.4 J.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    W=η⋅QC  ⟹  W=0.420⋅870=365.4 JW = \eta \cdot Q_C \implies W = 0.420 \cdot 870 = 365.4\text{ J}

    Correct

    η=1−QCQH  ⟹  QH=QC1−η\eta = 1 - \frac{Q_C}{Q_H} \implies Q_H = \frac{Q_C}{1 - \eta}

    Thermal efficiency is defined relative to the total heat input, η=WQH\eta = \frac{W}{Q_H}, not the exhausted heat QCQ_C. Therefore, W≠η⋅QCW \neq \eta \cdot Q_C.

  2. Step 2

    QH=W+QC  ⟹  QH=365.4+870  ⟹  QH=1235.4 JQ_H = W + Q_C \implies Q_H = 365.4 + 870 \implies Q_H = 1235.4\text{ J}

    Correct

    QH=870 J1−0.420=870 J0.580=1500 JQ_H = \frac{870\text{ J}}{1 - 0.420} = \frac{870\text{ J}}{0.580} = 1500\text{ J}

    Although your energy conservation relation QH=W+QCQ_H = W + Q_C is physically correct, this final calculation is incorrect because it uses the erroneous value of WW from Step 1.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly applied the conservation of energy principle relating heat absorbed, work output, and heat rejected: QH=W+QCQ_H = W + Q_C.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Efficiency base confusion

You treated thermal efficiency as a percentage of rejected heat rather than of absorbed heat.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Thermal efficiency η=useful outputtotal input=WQH\eta = \frac{\text{useful output}}{\text{total input}} = \frac{W}{Q_H} always compares work output to the input energy supplied by combustion (QHQ_H). Since W=QH−QCW = Q_H - Q_C, the rejected heat accounts for the remaining fraction, QCQH=1−η\frac{Q_C}{Q_H} = 1 - \eta.

REASONING PATH
Your ACEpath teacher’s suggested approach
Efficiency Definition
  • η=WQH=1−QCQH\eta = \frac{W}{Q_H} = 1 - \frac{Q_C}{Q_H}

  • Always identify the input energy (QHQ_H) as the denominator when applying efficiency formulas.

Solving for Heat Input
  • QH=QC1−ηQ_H = \frac{Q_C}{1 - \eta}

  • When given exhaust heat QCQ_C, express QCQ_C as (1−η)QH(1 - \eta)Q_H to isolate QHQ_H directly.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Express the rejected heat in terms of efficiency and total heat input: QC=(1−η)QHQ_C = (1 - \eta)Q_H.

  2. Solve for QHQ_H: QH=QC1−ηQ_H = \frac{Q_C}{1 - \eta}.

  3. Substitute the given values: QH=870 J1−0.420=870 J0.580Q_H = \frac{870\text{ J}}{1 - 0.420} = \frac{870\text{ J}}{0.580}.

  4. Evaluate the quotient: QH=1500 JQ_H = 1500\text{ J}.

Final answer

QH=1500 JQ_H = 1500\text{ J}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the Sankey energy flow diagram for a heat engine to keep the total input QHQ_H distinct from the rejected waste QCQ_C.

  • Practice rearranging η=1−QCQH\eta = 1 - \frac{Q_C}{Q_H} for both QHQ_H and QCQ_C before substituting numerical values.

Lock it in

Similar question

01

A turbine operates with a thermal efficiency of 35.0%35.0\%. During each cycle, it discharges 520 J520\text{ J} of heat into the environment. Calculate the total heat absorbed from the high-temperature reservoir per cycle.

Answer

QH=800 JQ_H = 800\text{ J}. Key steps: QCQH=1−η=1−0.350=0.650\frac{Q_C}{Q_H} = 1 - \eta = 1 - 0.350 = 0.650, so QH=520 J0.650=800 JQ_H = \frac{520\text{ J}}{0.650} = 800\text{ J}.

02

A heat engine operating at an efficiency of 28.0%28.0\% expels 1800 J1800\text{ J} of heat to the cold reservoir per second. Find the useful work output produced by the engine per second.

Answer

W=700 JW = 700\text{ J}. Key steps: QH=QC1−η=18000.720=2500 JQ_H = \frac{Q_C}{1 - \eta} = \frac{1800}{0.720} = 2500\text{ J}. Then W=QH−QC=2500 J−1800 J=700 JW = Q_H - Q_C = 2500\text{ J} - 1800\text{ J} = 700\text{ J} (or W=ηQH=0.280×2500 J=700 JW = \eta Q_H = 0.280 \times 2500\text{ J} = 700\text{ J}).

03

An engineer wants to improve an engine whose efficiency is currently 30.0%30.0\% while exhausting 1400 J1400\text{ J} of heat per cycle. If efficiency is boosted to 40.0%40.0\% while maintaining the exact same heat input QHQ_H, how much heat will now be expelled per cycle?

Answer

QC′=1200 JQ_C' = 1200\text{ J}. Key steps: Find original heat input QH=QC1−η1=14000.700=2000 JQ_H = \frac{Q_C}{1 - \eta_1} = \frac{1400}{0.700} = 2000\text{ J}. For the new efficiency η2=0.400\eta_2 = 0.400, the new heat rejected is QC′=(1−η2)QH=(1−0.400)(2000 J)=0.600×2000 J=1200 JQ_C' = (1 - \eta_2)Q_H = (1 - 0.400)(2000\text{ J}) = 0.600 \times 2000\text{ J} = 1200\text{ J}.

Loading workspace…