Resources

A hydraulic laboratory jack consists of a small input piston of area A1=4.50 cm2A_1 = 4.50\text{ cm}^2 and a large load piston of area A2=0.180 m2A_2 = 0.180\text{ m}^2 connected by an incompressible fluid. A technician applies an input force F1=65.0 NF_1 = 65.0\text{ N} to the small piston. Identify the fluid physics law applicable to this enclosed hydraulic system, show the conversion of the piston areas into standard SI units (extm2 ext{m}^2), and compute the maximum load force F2F_2 that can be supported by the large piston.

Answer and steps

Final answer

Pascal's Principle; A1=4.50×10−4 m2A_1 = 4.50\times 10^{-4}\text{ m}^2 and A2=0.180 m2A_2 = 0.180\text{ m}^2 with F1A1=F2A2\frac{F_1}{A_1} = \frac{F_2}{A_2}; F2=2.60×104 NF_2 = 2.60\times 10^4\text{ N}.

Steps

01

Applicable Physical Law

An enclosed hydraulic jack relies on Pascal's Principle (or Pascal's Law), which states that an external pressure applied to an enclosed, incompressible fluid is transmitted equally and undiminished to every portion of the fluid and to the walls of the containing vessel.

02

Unit Conversion to SI Units

The standard SI unit of area is the square meter (m2\text{m}^2).

  • For the input piston: 1 cm=10−2 m  ⟹  1 cm2=(10−2 m)2=10−4 m21\text{ cm} = 10^{-2}\text{ m} \implies 1\text{ cm}^2 = (10^{-2}\text{ m})^2 = 10^{-4}\text{ m}^2 A1=4.50 cm2=4.50×10−4 m2A_1 = 4.50\text{ cm}^2 = 4.50 \times 10^{-4}\text{ m}^2
  • For the load piston: A2=0.180 m2A_2 = 0.180\text{ m}^2 (Already in standard SI units)

Common Pitfall: When converting from cm2\text{cm}^2 to m2\text{m}^2, remember to square the linear conversion factor (10−210^{-2} becomes 10−410^{-4}). Dividing by 100100 instead of 10,00010{,}000 is a frequent mistake.

03

Calculating the Maximum Load Force (F2F_2)

According to Pascal's Principle, the fluid pressure PP is uniform at both pistons: P1=P2  ⟹  F1A1=F2A2P_1 = P_2 \implies \frac{F_1}{A_1} = \frac{F_2}{A_2}

Rearranging to solve for F2F_2: F2=F1(A2A1)F_2 = F_1 \left(\frac{A_2}{A_1}\right)

Substitute the known values: F2=65.0 N⋅(0.180 m24.50×10−4 m2)F_2 = 65.0\text{ N} \cdot \left(\frac{0.180\text{ m}^2}{4.50 \times 10^{-4}\text{ m}^2}\right)

F2=65.0 N⋅400=2.60×104 NF_2 = 65.0\text{ N} \cdot 400 = 2.60 \times 10^4\text{ N}

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student incorrectly converts square centimeters to square meters by dividing by 100 instead of 10000, resulting in an area of 0.0450 m² and an underestimated force.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    Pascal’s law\text{Pascal's law}

  2. Step 2

    1 m=100 cm  ⟹  A1=4.50100=0.0450 m21\text{ m} = 100\text{ cm} \implies A_1 = \frac{4.50}{100} = 0.0450\text{ m}^2

    Correct

    A1=4.50 cm2×(1 m100 cm)2=4.50×10−4 m2A_1 = 4.50\text{ cm}^2 \times \left(\frac{1\text{ m}}{100\text{ cm}}\right)^2 = 4.50 \times 10^{-4}\text{ m}^2

    You divided by 100100 instead of 1002=10,000100^2 = 10{,}000. Because area is two-dimensional, 1 m2=(100 cm)2=10,000 cm21\text{ m}^2 = (100\text{ cm})^2 = 10{,}000\text{ cm}^2.

  3. Step 3

    A2=0.180 m2A_2 = 0.180\text{ m}^2

  4. Step 4

    F2=F1×(A2A1)F_2 = F_1 \times \left(\frac{A_2}{A_1}\right)

  5. Step 5

    F2=65.0×(0.1800.0450)=260 NF_2 = 65.0 \times \left(\frac{0.180}{0.0450}\right) = 260\text{ N}

    Correct

    F2=65.0 N×(0.180 m24.50×10−4 m2)=2.60×104 NF_2 = 65.0\text{ N} \times \left(\frac{0.180\text{ m}^2}{4.50 \times 10^{-4}\text{ m}^2}\right) = 2.60 \times 10^4\text{ N}

    Your arithmetic follows logically from your substituted value of A1A_1, but the numerical result is off by a factor of 100100 due to the unit conversion error in Step 2.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly named Pascal's law as the governing principle for the hydraulic jack.

You identified that the load piston area was already in square meters.

You set up the force-to-area proportionality formula correctly.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Linear vs. Areal Unit Conversion

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You applied the one-dimensional length conversion factor (1 m=100 cm1\text{ m} = 100\text{ cm}) to an area quantity without squaring the conversion ratio. Area conversions require squaring both the unit and the conversion constant: 1 m2=(102 cm)2=104 cm21\text{ m}^2 = (10^2\text{ cm})^2 = 10^4\text{ cm}^2, so converting from cm2\text{cm}^2 to m2\text{m}^2 requires dividing by 10,00010{,}000 (or multiplying by 10−410^{-4}).

REASONING PATH
Your ACEpath teacher’s suggested approach
Area Conversion Rule
  • 1 m2=(102 cm)2=104 cm2=10,000 cm21\text{ m}^2 = (10^2\text{ cm})^2 = 10^4\text{ cm}^2 = 10{,}000\text{ cm}^2

  • Always square the linear conversion factor when converting units of area: multiply square centimeters by 10−410^{-4} to get square meters.

Pascal's Principle Ratio
  • F2F1=A2A1\frac{F_2}{F_1} = \frac{A_2}{A_1}

  • Check whether the mechanical advantage matches physical intuition: a small input area should yield a large area ratio and a substantially amplified force.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Convert A1A_1 using the squared dimensional conversion factor: A1=4.50 cm2×(1 m100 cm)2=4.50×10−4 m2A_1 = 4.50\text{ cm}^2 \times \left(\frac{1\text{ m}}{100\text{ cm}}\right)^2 = 4.50 \times 10^{-4}\text{ m}^2.

  2. Substitute the correct SI areas into the force equation: F2=65.0 N×(0.180 m24.50×10−4 m2)F_2 = 65.0\text{ N} \times \left(\frac{0.180\text{ m}^2}{4.50 \times 10^{-4}\text{ m}^2}\right).

  3. Evaluate the area ratio: 0.1804.50×10−4=400\frac{0.180}{4.50 \times 10^{-4}} = 400.

  4. Multiply the input force by the area ratio: F2=65.0 N×400=2.60×104 NF_2 = 65.0\text{ N} \times 400 = 2.60 \times 10^4\text{ N}.

Final answer

F2=2.60×104 NF_2 = 2.60 \times 10^4\text{ N} (or 26,000 N26{,}000\text{ N})

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice converting derived units (area cm2→m2\text{cm}^2 \to \text{m}^2 and volume cm3→m3\text{cm}^3 \to \text{m}^3) by writing out explicit conversion parentheses with powers.

  • Re-evaluate hydraulic jack problems by checking the magnitude of the force multiplication factor to catch unit mistakes early.

OverviewACEpath Teacher's Diagnosis

02 The student inverts the area ratio in the hydraulic formula, calculating F2 = F1 × (A1 / A2) and arriving at a diminished output force instead of mechanical amplification.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    Pascal’s principle\text{Pascal's principle}

  2. Step 2

    A1=4.50×10−4 m2  ⟹  A2=0.180 m2A_1 = 4.50 \times 10^{-4}\text{ m}^2 \implies A_2 = 0.180\text{ m}^2

  3. Step 3

    F1A2=F2A1  ⟹  F2=F1×(A1A2)\frac{F_1}{A_2} = \frac{F_2}{A_1} \implies F_2 = F_1 \times \left(\frac{A_1}{A_2}\right)

    Correct

    F1A1=F2A2  ⟹  F2=F1×(A2A1)\frac{F_1}{A_1} = \frac{F_2}{A_2} \implies F_2 = F_1 \times \left(\frac{A_2}{A_1}\right)

    Pascal's principle equates pressure at both pistons (P1=P2P_1 = P_2), meaning force is divided by its own corresponding area: F1A1=F2A2\frac{F_1}{A_1} = \frac{F_2}{A_2}. Pairing F1F_1 with A2A_2 inverted the ratio and produced a force reduction instead of mechanical advantage.

  4. Step 4

    F2=65.0×(0.0004500.180)=0.1625 NF_2 = 65.0 \times \left(\frac{0.000450}{0.180}\right) = 0.1625\text{ N}

    Correct

    F2=65.0 N×(0.180 m24.50×10−4 m2)=2.60×104 NF_2 = 65.0\text{ N} \times \left(\frac{0.180\text{ m}^2}{4.50 \times 10^{-4}\text{ m}^2}\right) = 2.60 \times 10^4\text{ N}

    Your arithmetic evaluation was mathematically consistent with your written formula, but the resulting value is incorrect because it inherited the inverted area ratio from the previous step.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified Pascal's principle as the physical law governing this system.

You executed the area unit conversion from cm2\text{cm}^2 to m2\text{m}^2 flawlessly.

You carried out the arithmetic evaluation accurately according to your written equation.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Inverted Hydraulic Ratio

You accidentally swapped the subscripts in the pressure equality, pairing the input force with the output area.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing how pressure equality translates into a proportion. Pressure is defined locally as P=FAP = \frac{F}{A}, so equating pressures requires F1A1=F2A2\frac{F_1}{A_1} = \frac{F_2}{A_2}, meaning the larger piston must exert a proportionally larger force.

REASONING PATH
Your ACEpath teacher’s suggested approach
Start from Pressure Definition
  • P=FAP = \frac{F}{A} and P1=P2P_1 = P_2

  • Always write down F1A1=F2A2\frac{F_1}{A_1} = \frac{F_2}{A_2} directly from P1=P2P_1 = P_2 before cross-multiplying or rearranging.

Physical Reality Check for Jacks
  • Hydraulic jacks amplify force (A2>A1  ⟹  F2>F1A_2 > A_1 \implies F_2 > F_1)

  • Verify whether your output force is larger than your input force when lifting a load.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. State the pressure balance from Pascal's principle: F1A1=F2A2\frac{F_1}{A_1} = \frac{F_2}{A_2}.

  2. Solve algebraically for the output force: F2=F1(A2A1)F_2 = F_1 \left(\frac{A_2}{A_1}\right).

  3. Substitute the given values: F2=65.0 N×(0.180 m24.50×10−4 m2)=65.0 N×400F_2 = 65.0\text{ N} \times \left(\frac{0.180\text{ m}^2}{4.50 \times 10^{-4}\text{ m}^2}\right) = 65.0\text{ N} \times 400.

Final answer

F2=2.60×104 NF_2 = 2.60 \times 10^4\text{ N}

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice deriving hydraulic proportions directly from P1=P2P_1 = P_2 before solving for the unknown variable.

  • Perform a sanity check on hydraulic lifting problems: since jacks provide a mechanical advantage, F2F_2 must be significantly larger than F1F_1.

OverviewACEpath Teacher's Diagnosis

03 The student mistakenly squares the already given areas as if they were radii or linear dimensions, resulting in an excessively large force.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    Pascal’s law\text{Pascal's law}

  2. Step 2

    A1=4.50×10−4 m2  ⟹  A2=0.180 m2A_1 = 4.50 \times 10^{-4}\text{ m}^2 \implies A_2 = 0.180\text{ m}^2

  3. Step 3

    F2=F1×(A22A12)  ⟹  F2=65.0×(0.1802(4.50×10−4)2)F_2 = F_1 \times \left(\frac{A_2^2}{A_1^2}\right) \implies F_2 = 65.0 \times \left(\frac{0.180^2}{(4.50 \times 10^{-4})^2}\right)

    Correct

    F2=F1(A2A1)=65.0 N×(0.180 m24.50×10−4 m2)F_2 = F_1 \left(\frac{A_2}{A_1}\right) = 65.0\text{ N} \times \left(\frac{0.180\text{ m}^2}{4.50 \times 10^{-4}\text{ m}^2}\right)

    Pascal's principle equates pressure, giving F1A1=F2A2\frac{F_1}{A_1} = \frac{F_2}{A_2}, so the force ratio is linear with the area ratio A2A1\frac{A_2}{A_1}. You squared the cross-sectional areas as if they were radii or diameters.

  4. Step 4

    F2=65.0×160000=10400000 NF_2 = 65.0 \times 160000 = 10400000\text{ N}

    Correct

    F2=65.0 N×400=2.60×104 NF_2 = 65.0\text{ N} \times 400 = 2.60 \times 10^4\text{ N}

    Your arithmetic follows correctly from your modified formula, but the result is overstated by a factor of 400400 due to squaring the areas in Step 3.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified Pascal's law as the applicable principle for this hydraulic system.

You accurately converted 4.50 cm24.50\text{ cm}^2 into standard SI units as 4.50×10−4 m24.50 \times 10^{-4}\text{ m}^2.

You executed clean and organized algebraic substitutions and arithmetic operations.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Superfluous Squaring of Area Quantities

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You confused the force ratio involving cross-sectional areas, F2F1=A2A1\frac{F_2}{F_1} = \frac{A_2}{A_1}, with the force ratio involving radii or diameters, F2F1=(r2r1)2\frac{F_2}{F_1} = \left(\frac{r_2}{r_1}\right)^2. Because the problem already provided areas (A1A_1 and A2A_2), squaring them resulted in an incorrect A2A^2 relationship.

REASONING PATH
Your ACEpath teacher’s suggested approach
Inspect Given Dimensions
  • Check the unit of the given size: if it has units of m\text{m} or cm\text{cm}, it is a linear dimension (rr or dd); if it has units of m2\text{m}^2 or cm2\text{cm}^2, it is already an area (AA).

  • Use F2=F1(A2A1)F_2 = F_1 \left(\frac{A_2}{A_1}\right) directly when areas are given, and only square the ratio when radii or diameters are given: F2=F1(r2r1)2F_2 = F_1 \left(\frac{r_2}{r_1}\right)^2.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. State the pressure equality from Pascal's law: P1=P2  ⟹  F1A1=F2A2P_1 = P_2 \implies \frac{F_1}{A_1} = \frac{F_2}{A_2}.

  2. Solve for the load force: F2=F1(A2A1)F_2 = F_1 \left(\frac{A_2}{A_1}\right).

  3. Substitute the known values directly without squaring: F2=65.0 N×(0.180 m24.50×10−4 m2)=65.0 N×400F_2 = 65.0\text{ N} \times \left(\frac{0.180\text{ m}^2}{4.50 \times 10^{-4}\text{ m}^2}\right) = 65.0\text{ N} \times 400.

Final answer

F2=2.60×104 NF_2 = 2.60 \times 10^4\text{ N}

NEXT STEPS
Final Takeaways from Your Teacher
  • When setting up hydraulic jack problems, circle the units of the piston sizes to confirm whether you are given area (AA) or radius/diameter (r,dr, d).

  • Practice writing P1=P2P_1 = P_2 first, then F1A1=F2A2\frac{F_1}{A_1} = \frac{F_2}{A_2}, before replacing AA with πr2\pi r^2 only if necessary.

Lock it in

Similar question

01

A hydraulic lift has an input piston of area A1=8.00 cm2A_1 = 8.00\text{ cm}^2 and an output piston of area A2=0.400 m2A_2 = 0.400\text{ m}^2. If an input force of F1=120 NF_1 = 120\text{ N} is applied, what is the maximum output force F2F_2?

Answer

F2=6.00×104 NF_2 = 6.00 \times 10^4\text{ N}. First convert A1=8.00 cm2=8.00×10−4 m2A_1 = 8.00\text{ cm}^2 = 8.00 \times 10^{-4}\text{ m}^2. The area ratio is A2A1=0.4008.00×10−4=500\frac{A_2}{A_1} = \frac{0.400}{8.00 \times 10^{-4}} = 500. Then F2=120 N×500=6.00×104 NF_2 = 120\text{ N} \times 500 = 6.00 \times 10^4\text{ N}.

02

A circular input piston has a radius of r1=1.50 cmr_1 = 1.50\text{ cm} and supports an applied force of 45.0 N45.0\text{ N}. A circular output piston has a radius of r2=15.0 cmr_2 = 15.0\text{ cm}. Find the output force F2F_2 supported by the larger piston.

Answer

F2=4.50×103 NF_2 = 4.50 \times 10^3\text{ N}. Since area scales with the square of the radius, A2A1=(r2r1)2=(15.0 cm1.50 cm)2=102=100\frac{A_2}{A_1} = \left(\frac{r_2}{r_1}\right)^2 = \left(\frac{15.0\text{ cm}}{1.50\text{ cm}}\right)^2 = 10^2 = 100. Therefore, F2=F1×100=45.0 N×100=4.50×103 NF_2 = F_1 \times 100 = 45.0\text{ N} \times 100 = 4.50 \times 10^3\text{ N}.

03

A car lift uses compressed air acting on a small piston of diameter d1=5.00 cmd_1 = 5.00\text{ cm} to raise a car of mass m=1800 kgm = 1800\text{ kg} resting on a large piston of diameter d2=30.0 cmd_2 = 30.0\text{ cm}. Taking g=9.80 m/s2g = 9.80\text{ m/s}^2, determine the minimum gauge pressure required in the hydraulic line and the minimum force applied to the small piston.

Answer

Gauge pressure P=2.49×105 PaP = 2.49 \times 10^5\text{ Pa}; Force F1=490 NF_1 = 490\text{ N}. The required output force is F2=mg=1800 kg×9.80 m/s2=1.764×104 NF_2 = mg = 1800\text{ kg} \times 9.80\text{ m/s}^2 = 1.764 \times 10^4\text{ N}. The large piston area is A2=π(0.150 m)2=0.07069 m2A_2 = \pi (0.150\text{ m})^2 = 0.07069\text{ m}^2, giving gauge pressure P=F2A2=1.764×1040.07069≈2.495×105 PaP = \frac{F_2}{A_2} = \frac{1.764 \times 10^4}{0.07069} \approx 2.495 \times 10^5\text{ Pa}. The small piston area is A1=π(0.0250 m)2=1.9635×10−3 m2A_1 = \pi (0.0250\text{ m})^2 = 1.9635 \times 10^{-3}\text{ m}^2. The required force is F1=P×A1=(2.495×105 Pa)(1.9635×10−3 m2)≈490 NF_1 = P \times A_1 = (2.495 \times 10^5\text{ Pa})(1.9635 \times 10^{-3}\text{ m}^2) \approx 490\text{ N} (or using force ratio F1=F2×(d1/d2)2=17,640×(5/30)2=490 NF_1 = F_2 \times (d_1/d_2)^2 = 17{,}640 \times (5/30)^2 = 490\text{ N}).

Loading workspace…