Resources

An electric vehicle battery pack consists of two identical modules, each with an internal electromotive force of E=48.0 V\mathcal{E} = 48.0\ \text{V} and internal resistance r=0.250 Ωr = 0.250\ \Omega. During an erroneous servicing procedure, Module B is wired in reverse polarity (opposing direction) relative to Module A in a single closed loop containing an external load resistor of Rload=5.50 V/1.00 A=5.50 ΩR_{\text{load}} = 5.50\ \text{V} / 1.00\ \text{A} = 5.50\ \Omega. When connected correctly in series-aiding polarity: (a) calculate the rate of electrical energy delivered to the load resistor PloadP_{\text{load}}. (b) When connected in the opposing-polarity configuration, calculate the net electric current IoppI_{\text{opp}} through the loop and the power dissipated by the external load resistor Pload,oppP_{\text{load,opp}}.

Answer and steps

Final answer

(a) Pload=1.41×103 WP_{\text{load}} = 1.41 \times 10^3\ \text{W}; (b) Iopp=0 AI_{\text{opp}} = 0\ \text{A} and Pload,opp=0 WP_{\text{load,opp}} = 0\ \text{W}

Steps

Part (a): Power Delivered in Series-Aiding Polarity

  1. Find the net electromotive force (Enet\mathcal{E}_{\text{net}}): When the two identical battery modules are connected in series-aiding polarity, their electromotive forces (EMFs) reinforce each other: Enet=EA+EB=48.0 V+48.0 V=96.0 V\mathcal{E}_{\text{net}} = \mathcal{E}_A + \mathcal{E}_B = 48.0\ \text{V} + 48.0\ \text{V} = 96.0\ \text{V}
  2. Calculate the total equivalent resistance (RtotalR_{\text{total}}): The single-loop circuit includes the internal resistance of both modules and the external load resistor connected in series: Rtotal=rA+rB+Rload=0.250 Ω+0.250 Ω+5.50 Ω=6.00 ΩR_{\text{total}} = r_A + r_B + R_{\text{load}} = 0.250\ \Omega + 0.250\ \Omega + 5.50\ \Omega = 6.00\ \Omega
  3. Determine the loop current (II): Applying Ohm's law to the complete circuit: I=EnetRtotal=96.0 V6.00 Ω=16.0 AI = \frac{\mathcal{E}_{\text{net}}}{R_{\text{total}}} = \frac{96.0\ \text{V}}{6.00\ \Omega} = 16.0\ \text{A}
  4. Calculate the power delivered to the load resistor (PloadP_{\text{load}}): Using Joule's law for the power dissipated specifically across RloadR_{\text{load}}: Pload=I2Rload=(16.0 A)2⋅5.50 Ω=256 A2⋅5.50 Ω=1408 W≈1.41×103 WP_{\text{load}} = I^2 R_{\text{load}} = (16.0\ \text{A})^2 \cdot 5.50\ \Omega = 256\ \text{A}^2 \cdot 5.50\ \Omega = 1408\ \text{W} \approx 1.41 \times 10^3\ \text{W}

Part (b): Current and Power in Opposing-Polarity Configuration

  1. Determine the net electromotive force (Enet,opp\mathcal{E}_{\text{net,opp}}): When Module B is wired in reverse polarity, its EMF opposes the EMF of Module A: Enet,opp=EA−EB=48.0 V−48.0 V=0 V\mathcal{E}_{\text{net,opp}} = \mathcal{E}_A - \mathcal{E}_B = 48.0\ \text{V} - 48.0\ \text{V} = 0\ \text{V}
  2. Calculate the net loop current (IoppI_{\text{opp}}):

    Pitfall to avoid: While the EMFs subtract due to opposing orientations, electrical resistances are scalar properties that always impede current and thus remain additive (Rtotal=6.00 ΩR_{\text{total}} = 6.00\ \Omega).

    Applying Ohm's law with the opposing net EMF: Iopp=Enet,oppRtotal=0 V6.00 Ω=0 AI_{\text{opp}} = \frac{\mathcal{E}_{\text{net,opp}}}{R_{\text{total}}} = \frac{0\ \text{V}}{6.00\ \Omega} = 0\ \text{A}

  3. Calculate the power dissipated by the load (Pload,oppP_{\text{load,opp}}): Because there is no current passing through the load resistor: Pload,opp=Iopp2Rload=(0 A)2⋅5.50 Ω=0 WP_{\text{load,opp}} = I_{\text{opp}}^2 R_{\text{load}} = (0\ \text{A})^2 \cdot 5.50\ \Omega = 0\ \text{W}

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student subtracts internal resistances along with the opposing emf, incorrectly believing reverse polarity subtracts internal resistance.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    Etotal=48.0 V+48.0 V=96.0 V  ⟹  Rtotal=5.50 Ω+0.250 Ω+0.250 Ω=6.00 ΩE_{\text{total}} = 48.0\ \text{V} + 48.0\ \text{V} = 96.0\ \text{V} \implies R_{\text{total}} = 5.50\ \Omega + 0.250\ \Omega + 0.250\ \Omega = 6.00\ \Omega

  2. Step 2

    I=96.0 V/6.00 Ω=16.0 A  ⟹  Pload=(16.0 A)2∗5.50 Ω=1408 WI = 96.0\ \text{V} / 6.00\ \Omega = 16.0\ \text{A} \implies P_{\text{load}} = (16.0\ \text{A})^2 * 5.50\ \Omega = 1408\ \text{W}

  3. Step 3

    Enet=48.0 V−48.0 V=0 VE_{\text{net}} = 48.0\ \text{V} - 48.0\ \text{V} = 0\ \text{V}

  4. Step 4

    Rtotal=5.50 Ω+0.250 Ω−0.250 Ω=5.50 ΩR_{\text{total}} = 5.50\ \Omega + 0.250\ \Omega - 0.250\ \Omega = 5.50\ \Omega

    Correct

    Rtotal=5.50 Ω+0.250 Ω+0.250 Ω=6.00 ΩR_{\text{total}} = 5.50\ \Omega + 0.250\ \Omega + 0.250\ \Omega = 6.00\ \Omega

    You subtracted the internal resistance of the reversed module. Reversing a source's physical orientation flips its potential difference direction, but internal resistance is a passive scalar property that dissipates electrical energy and always adds to the total series resistance.

  5. Step 5

    Iopp=0 V/5.50 Ω=0 A  ⟹  Pload,opp=(0 A)2∗5.50 Ω=0 WI_{\text{opp}} = 0\ \text{V} / 5.50\ \Omega = 0\ \text{A} \implies P_{\text{load,opp}} = (0\ \text{A})^2 * 5.50\ \Omega = 0\ \text{W}

    Correct

    Iopp=0 V6.00 Ω=0 A  ⟹  Pload,opp=(0 A)2⋅5.50 Ω=0 WI_{\text{opp}} = \frac{0\ \text{V}}{6.00\ \Omega} = 0\ \text{A} \implies P_{\text{load,opp}} = (0\ \text{A})^2 \cdot 5.50\ \Omega = 0\ \text{W}

    Because your net electromotive force was 0 V0\ \text{V}, your final values for current and power evaluated to zero, but the calculation relied on the incorrect total resistance from the previous step.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly calculated the reinforced net EMF and total series resistance in part (a).

You applied Joule's law accurately to find the power dissipated across the load resistor.

You recognized that reversing the battery module causes its electromotive force to oppose the other module.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Subtracted internal resistance in opposing polarity

You subtracted the internal resistance of Module B because its polarity was reversed.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You conflated directed electrical potential differences (EMFs, which depend on polarity and can oppose each other) with passive electrical resistance (which is always positive and dissipative in series).

REASONING PATH
Your ACEpath teacher’s suggested approach
Resistance is Always Additive in Series
  • For any passive components in a single series loop, Rtotal=∑RiR_{\text{total}} = \sum R_i, regardless of source orientation.

  • Keep all internal and external resistances strictly positive when calculating total equivalent resistance.

Polarity Affects Only EMF
  • Kirchhoff's loop rule accounts for source orientation via potential changes (±E±\mathcal{E}), while every resistive voltage drop is −IR-I R.

  • Apply signs only to electromotive forces when setting up the loop equation ∑E−I∑R=0\sum \mathcal{E} - I \sum R = 0.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Sum all series resistances as positive values: Rtotal=Rload+rA+rB=5.50 Ω+0.250 Ω+0.250 Ω=6.00 ΩR_{\text{total}} = R_{\text{load}} + r_A + r_B = 5.50\ \Omega + 0.250\ \Omega + 0.250\ \Omega = 6.00\ \Omega.

  2. Apply Ohm's law using the correct total resistance: Iopp=Enet,oppRtotal=0 V6.00 Ω=0 AI_{\text{opp}} = \frac{\mathcal{E}_{\text{net,opp}}}{R_{\text{total}}} = \frac{0\ \text{V}}{6.00\ \Omega} = 0\ \text{A}.

  3. Calculate the load power dissipation: Pload,opp=Iopp2Rload=(0 A)2⋅5.50 Ω=0 WP_{\text{load,opp}} = I_{\text{opp}}^2 R_{\text{load}} = (0\ \text{A})^2 \cdot 5.50\ \Omega = 0\ \text{W}.

Final answer

(a) Pload=1.41×103 WP_{\text{load}} = 1.41 \times 10^3\ \text{W}; (b) Iopp=0 AI_{\text{opp}} = 0\ \text{A} and Pload,opp=0 WP_{\text{load,opp}} = 0\ \text{W}

NEXT STEPS
Final Takeaways from Your Teacher
  • Write out Kirchhoff's loop rule explicitly as ∑E−I∑R=0\sum \mathcal{E} - I \sum R = 0 so you clearly separate signed EMFs from additive resistances.

  • Practice problems where two opposing batteries have unequal EMFs to ensure your total resistance does not alter the non-zero current calculation.

OverviewACEpath Teacher's Diagnosis

02 The student forgets to square the current when calculating electric power delivered to the load resistor, writing P = I * R instead of P = I² * R.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    Etotal=48.0 V+48.0 V=96.0 V  ⟹  Rtotal=5.50 Ω+2(0.250 Ω)=6.00 Ω  ⟹  I=96.0 V/6.00 Ω=16.0 AE_{\text{total}} = 48.0\text{ V} + 48.0\text{ V} = 96.0\text{ V} \implies R_{\text{total}} = 5.50\ \Omega + 2(0.250\ \Omega) = 6.00\ \Omega \implies I = 96.0\text{ V} / 6.00\ \Omega = 16.0\text{ A}

  2. Step 2

    Pload=I∗Rload=16.0 A∗5.50 Ω=88.0 WP_{\text{load}} = I * R_{\text{load}} = 16.0\text{ A} * 5.50\ \Omega = 88.0\text{ W}

    Correct

    Pload=I2Rload=(16.0 A)2⋅5.50 Ω=1.41×103 WP_{\text{load}} = I^2 R_{\text{load}} = (16.0\text{ A})^2 \cdot 5.50\ \Omega = 1.41 \times 10^3\text{ W}

    You multiplied current directly by resistance (IRI R), which calculates the potential difference across the load in volts rather than the dissipated power in watts. Joule's law requires squaring the current: P=I2RP = I^2 R.

  3. Step 3

    Enet=48.0 V−48.0 V=0 V  ⟹  Rtotal=5.50 Ω+2(0.250 Ω)=6.00 Ω  ⟹  Iopp=0 V/6.00 Ω=0 AE_{\text{net}} = 48.0\text{ V} - 48.0\text{ V} = 0\text{ V} \implies R_{\text{total}} = 5.50\ \Omega + 2(0.250\ \Omega) = 6.00\ \Omega \implies I_{\text{opp}} = 0\text{ V} / 6.00\ \Omega = 0\text{ A}

  4. Step 4

    Pload,opp=0 A∗5.50 Ω=0 WP_{\text{load,opp}} = 0\text{ A} * 5.50\ \Omega = 0\text{ W}

    Correct

    Pload,opp=Iopp2Rload=(0 A)2⋅5.50 Ω=0 WP_{\text{load,opp}} = I_{\text{opp}}^2 R_{\text{load}} = (0\text{ A})^2 \cdot 5.50\ \Omega = 0\text{ W}

    Although your numerical answer of 0 W0\text{ W} is correct because the current is zero, you repeated the formula mistake by writing P=IRP = I R instead of P=I2RP = I^2 R.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly calculated the net EMF for both aiding and opposing battery orientations.

You properly summed the external load resistance with both internal resistances.

You accurately found the total current in both circuit configurations using Ohm's law.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Ohm's Law vs. Joule's Law Confusion

You wrote P=IRP = I R instead of P=I2RP = I^2 R, omitting the exponent on current.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You conflated the formula for voltage drop (V=IRV = I R) with the formula for electrical power dissipation (P=I2R=VIP = I^2 R = V I). Multiplying current by resistance yields units of volts (V\text{V}), not watts (W\text{W}).

REASONING PATH
Your ACEpath teacher’s suggested approach
Dimensional Unit Check
  • Power has units of watts (W=J/s=V⋅A=A2⋅Ω\text{W} = \text{J/s} = \text{V} \cdot \text{A} = \text{A}^2 \cdot \Omega). Voltage has units of volts (V=A⋅Ω\text{V} = \text{A} \cdot \Omega).

  • Always verify that your power expression contains current squared (I2RI^2 R), voltage squared (V2/RV^2 / R), or current times voltage (IVI V).

Joule Heating Formula
  • The rate of thermal dissipation in a constant resistance RR carrying current II is P=I2RP = I^2 R.

  • When you have current and resistance, square the current before multiplying by the resistance.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Square the loop current: I2=(16.0 A)2=256 A2I^2 = (16.0\text{ A})^2 = 256\text{ A}^2.

  2. Multiply by the load resistance: Pload=256 A2⋅5.50 Ω=1408 WP_{\text{load}} = 256\text{ A}^2 \cdot 5.50\ \Omega = 1408\text{ W}.

  3. Express in standard scientific notation with three significant figures: Pload=1.41×103 WP_{\text{load}} = 1.41 \times 10^3\text{ W}.

Final answer

(a) Pload=1.41×103 WP_{\text{load}} = 1.41 \times 10^3\text{ W}; (b) Iopp=0 AI_{\text{opp}} = 0\text{ A} and Pload,opp=0 WP_{\text{load,opp}} = 0\text{ W}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the three fundamental power relationships: P=VIP = V I, P=I2RP = I^2 R, and P=V2RP = \frac{V^2}{R}.

  • Practice checking dimensional consistency on each formula line before writing numerical values.

  • Solve the practice problems below to master Joule heating calculations.

OverviewACEpath Teacher's Diagnosis

03 The student omits the battery modules' internal resistances entirely, treating the modules as ideal voltage sources.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    Etotal=48.0 V+48.0 V=96.0 VE_{\text{total}} = 48.0\text{ V} + 48.0\text{ V} = 96.0\text{ V}

  2. Step 2

    I=96.0 V/5.50 Ω=17.45 AI = 96.0\text{ V} / 5.50\ \Omega = 17.45\text{ A}

    Correct

    I=EnetRload+rA+rB=96.0 V5.50 Ω+0.250 Ω+0.250 Ω=96.0 V6.00 Ω=16.0 AI = \frac{\mathcal{E}_{\text{net}}}{R_{\text{load}} + r_A + r_B} = \frac{96.0\text{ V}}{5.50\ \Omega + 0.250\ \Omega + 0.250\ \Omega} = \frac{96.0\text{ V}}{6.00\ \Omega} = 16.0\text{ A}

    You omitted the internal resistance (r=0.250 Ωr = 0.250\ \Omega) of each battery module. Real voltage sources have internal resistance in series with the external load, so Rtotal=5.50 Ω+0.250 Ω+0.250 Ω=6.00 ΩR_{\text{total}} = 5.50\ \Omega + 0.250\ \Omega + 0.250\ \Omega = 6.00\ \Omega.

  3. Step 3

    Pload=(17.45 A)2⋅5.50 Ω=1675 WP_{\text{load}} = (17.45\text{ A})^2 \cdot 5.50\ \Omega = 1675\text{ W}

    Correct

    Pload=I2Rload=(16.0 A)2⋅5.50 Ω=1408 W≈1.41×103 WP_{\text{load}} = I^2 R_{\text{load}} = (16.0\text{ A})^2 \cdot 5.50\ \Omega = 1408\text{ W} \approx 1.41 \times 10^3\text{ W}

    You applied Joule's power formula P=I2RP = I^2 R correctly, but your numerical answer was skewed by the overestimated current from Step 2.

  4. Step 4

    Enet=48.0 V−48.0 V=0 VE_{\text{net}} = 48.0\text{ V} - 48.0\text{ V} = 0\text{ V}

  5. Step 5

    Iopp=0 V/5.50 Ω=0 AI_{\text{opp}} = 0\text{ V} / 5.50\ \Omega = 0\text{ A}

    Correct

    Iopp=Enet,oppRtotal=0 V6.00 Ω=0 AI_{\text{opp}} = \frac{\mathcal{E}_{\text{net,opp}}}{R_{\text{total}}} = \frac{0\text{ V}}{6.00\ \Omega} = 0\text{ A}

    Your final current is zero because the numerator is zero, but the denominator still omitted the internal resistance of both modules (Rtotal=6.00 ΩR_{\text{total}} = 6.00\ \Omega). While EMFs subtract in opposing polarity, internal resistances always add.

  6. Step 6

    Pload,opp=(0 A)2⋅5.50 Ω=0 WP_{\text{load,opp}} = (0\text{ A})^2 \cdot 5.50\ \Omega = 0\text{ W}

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly calculated the net EMF for both aiding and opposing configurations.

You used the correct relationship between current, resistance, and dissipated power across the load.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Omission of internal resistance

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated the battery modules as ideal voltage sources with zero resistance, ignoring the stated internal resistance r=0.250 Ωr = 0.250\ \Omega of each module in the circuit's total equivalent resistance.

REASONING PATH
Your ACEpath teacher’s suggested approach
Account for real source resistance
  • Every real source of EMF has an internal resistance rr that is placed in series with the external circuit.

  • Always add internal resistances to external resistances when finding the total loop resistance: Rtotal=Rload+∑riR_{\text{total}} = R_{\text{load}} + \sum r_i.

Resistances always add in series
  • Even when EMFs oppose each other and subtract, physical resistances always oppose current flow and add as positive scalars.

  • Never subtract internal resistances; calculate Rtotal=Rload+rA+rBR_{\text{total}} = R_{\text{load}} + r_A + r_B regardless of battery polarity.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Include the internal resistance of both battery modules in the total resistance: Rtotal=Rload+rA+rB=5.50 Ω+0.250 Ω+0.250 Ω=6.00 ΩR_{\text{total}} = R_{\text{load}} + r_A + r_B = 5.50\ \Omega + 0.250\ \Omega + 0.250\ \Omega = 6.00\ \Omega.

  2. Calculate the series-aiding current: I=EnetRtotal=96.0 V6.00 Ω=16.0 AI = \frac{\mathcal{E}_{\text{net}}}{R_{\text{total}}} = \frac{96.0\text{ V}}{6.00\ \Omega} = 16.0\text{ A}.

  3. Calculate the power dissipated across the load resistor: Pload=I2Rload=(16.0 A)2⋅5.50 Ω=1408 W≈1.41×103 WP_{\text{load}} = I^2 R_{\text{load}} = (16.0\text{ A})^2 \cdot 5.50\ \Omega = 1408\text{ W} \approx 1.41 \times 10^3\text{ W}.

Final answer

(a) Pload=1.41×103 WP_{\text{load}} = 1.41 \times 10^3\text{ W}; (b) Iopp=0 AI_{\text{opp}} = 0\text{ A} and Pload,opp=0 WP_{\text{load,opp}} = 0\text{ W}

NEXT STEPS
Final Takeaways from Your Teacher
  • Draw an equivalent circuit diagram with each real battery explicitly split into an ideal EMF source and an internal resistor rr.

  • Review whether battery orientation affects resistance (resistances are strictly additive scalars).

  • Complete the targeted flashcards and practice problems on real batteries with internal resistance.

Lock it in

Similar question

01

Two batteries, Battery 1 (E1=24.0 V\mathcal{E}_1 = 24.0\ \text{V}, r1=0.50 Ωr_1 = 0.50\ \Omega) and Battery 2 (E2=12.0 V\mathcal{E}_2 = 12.0\ \text{V}, r2=0.50 Ωr_2 = 0.50\ \Omega), are connected in series-opposing polarity across an external resistor R=5.00 ΩR = 5.00\ \Omega. Calculate the circuit current II and the power dissipated by the external resistor.

Answer

I=2.00 AI = 2.00\ \text{A} and P=20.0 WP = 20.0\ \text{W}. Key steps: Enet=24.0 V−12.0 V=12.0 V\mathcal{E}_{\text{net}} = 24.0\ \text{V} - 12.0\ \text{V} = 12.0\ \text{V}; Rtotal=5.00 Ω+0.50 Ω+0.50 Ω=6.00 ΩR_{\text{total}} = 5.00\ \Omega + 0.50\ \Omega + 0.50\ \Omega = 6.00\ \Omega; I=12.0 V/6.00 Ω=2.00 AI = 12.0\ \text{V} / 6.00\ \Omega = 2.00\ \text{A}; P=I2R=(2.00 A)2(5.00 Ω)=20.0 WP = I^2 R = (2.00\ \text{A})^2 (5.00\ \Omega) = 20.0\ \text{W}.

02

A technician connects three identical cells in series, each having E=6.0 V\mathcal{E} = 6.0\ \text{V} and r=0.20 Ωr = 0.20\ \Omega, across an 8.4 Ω8.4\ \Omega light bulb. By mistake, one cell is reversed. Find the current delivered to the bulb and the rate of energy dissipation inside the reversed cell's internal resistance.

Answer

I=0.67 AI = 0.67\ \text{A} (2/3 A2/3\ \text{A}) and Pinternal≈0.089 WP_{\text{internal}} \approx 0.089\ \text{W}. Key steps: Enet=6.0 V+6.0 V−6.0 V=6.0 V\mathcal{E}_{\text{net}} = 6.0\ \text{V} + 6.0\ \text{V} - 6.0\ \text{V} = 6.0\ \text{V}; all internal resistances add: Rtotal=8.4 Ω+3(0.20 Ω)=9.0 ΩR_{\text{total}} = 8.4\ \Omega + 3(0.20\ \Omega) = 9.0\ \Omega; I=6.0 V/9.0 Ω=0.667 AI = 6.0\ \text{V} / 9.0\ \Omega = 0.667\ \text{A}; Pinternal=I2r=(0.667 A)2(0.20 Ω)≈0.089 WP_{\text{internal}} = I^2 r = (0.667\ \text{A})^2 (0.20\ \Omega) \approx 0.089\ \text{W}.

03

A DC charging source with Echarger=60.0 V\mathcal{E}_{\text{charger}} = 60.0\ \text{V} and internal resistance r1=0.40 Ωr_1 = 0.40\ \Omega is connected to charge a battery with Ebat=48.0 V\mathcal{E}_{\text{bat}} = 48.0\ \text{V} and internal resistance r2=0.60 Ωr_2 = 0.60\ \Omega through lead wires totaling Rwire=1.00 ΩR_{\text{wire}} = 1.00\ \Omega (positive terminal connected to positive terminal). Determine the charging current and verify that the total rate of chemical energy absorbed plus thermal energy dissipated equals the rate of energy supplied by the charger.

Answer

I=6.0 AI = 6.0\ \text{A}; Power check: Psupplied=360 WP_{\text{supplied}} = 360\ \text{W}, Pabsorbed,chem=288 WP_{\text{absorbed,chem}} = 288\ \text{W}, Pthermal=72 WP_{\text{thermal}} = 72\ \text{W}, and 288 W+72 W=360 W288\ \text{W} + 72\ \text{W} = 360\ \text{W}. Key steps: Enet=60.0 V−48.0 V=12.0 V\mathcal{E}_{\text{net}} = 60.0\ \text{V} - 48.0\ \text{V} = 12.0\ \text{V}; Rtotal=0.40 Ω+0.60 Ω+1.00 Ω=2.00 ΩR_{\text{total}} = 0.40\ \Omega + 0.60\ \Omega + 1.00\ \Omega = 2.00\ \Omega; I=12.0/2.00=6.0 AI = 12.0 / 2.00 = 6.0\ \text{A}. Charger supplies EchargerI=60.0×6.0=360 W\mathcal{E}_{\text{charger}} I = 60.0 \times 6.0 = 360\ \text{W}. Battery stores EbatI=48.0×6.0=288 W\mathcal{E}_{\text{bat}} I = 48.0 \times 6.0 = 288\ \text{W}. Thermal loss in all resistances is I2Rtotal=36×2.00=72 WI^2 R_{\text{total}} = 36 \times 2.00 = 72\ \text{W}.

Loading workspace…