Resources

Consider an ideal voltmeter and an ideal ammeter placed into a single-loop circuit containing an EMF source E=12.0 V\mathcal{E} = 12.0\text{ V} and a load resistor Rload=24.0 ΩR_{\text{load}} = 24.0\ \Omega. In real instrumentation, an ammeter has a small internal resistance rAr_A while a voltmeter has a very large internal resistance RVR_V. (a) In the limit where the ammeter approaches the ideal asymptotic state (rA→0 Ωr_A \to 0\ \Omega), evaluate the circuit current II when the ammeter is placed in series with RloadR_{\text{load}}. (b) In the catastrophic limit where a careless student mistakenly places an ideal voltmeter (RV→∞R_V \to \infty) directly in series with RloadR_{\text{load}} instead of in parallel, evaluate the resulting circuit current IseriesI_{\text{series}} and the voltage reading across the voltmeter terminals. (c) Explain conceptually how this demonstrates that voltage can exist across two points even when current is effectively zero.

Answer and steps

Final answer

(a) I=lim⁡rA→0ERload+rA=12.0 V24.0 Ω=0.500 AI = \lim_{r_A \to 0} \frac{\mathcal{E}}{R_{\text{load}} + r_A} = \frac{12.0\text{ V}}{24.0\ \Omega} = 0.500\text{ A}; (b) Iseries=lim⁡RV→∞12.0 V24.0 Ω+RV=0 AI_{\text{series}} = \lim_{R_V \to \infty} \frac{12.0\text{ V}}{24.0\ \Omega + R_V} = 0\text{ A}, and Vmeter=lim⁡RV→∞[ERVRload+RV]=12.0 VV_{\text{meter}} = \lim_{R_V \to \infty} \left[ \mathcal{E} \frac{R_V}{R_{\text{load}} + R_V} \right] = 12.0\text{ V}; (c) Voltage represents the electric potential difference (energy per unit charge available to do work) between two points and exists independently of whether a closed low-resistance conducting path permits charge flow; when RV→∞R_V \to \infty, the open-circuit condition prevents current (I=0I = 0), yet the full 12.0 V12.0\text{ V} driving potential appears directly across the meter's terminals.

Steps

Part (a): Current with an Ideal Ammeter in Series

  1. Understand the Meter Characteristics: An ammeter measures electric current flowing through a branch and must be connected in series. To avoid altering the current it is intended to measure, an ideal ammeter has zero internal resistance (rA→0 Ωr_A \to 0\ \Omega).
  2. Calculate Total Resistance and Current: In a single loop containing the source E\mathcal{E}, the load resistor RloadR_{\text{load}}, and the ammeter resistance rAr_A in series: Rtotal=Rload+rAR_{\text{total}} = R_{\text{load}} + r_A

    Applying Ohm's law and taking the ideal limit rA→0 Ωr_A \to 0\ \Omega: I=lim⁡rA→0ERload+rA=12.0 V24.0 Ω+0 Ω=0.500 AI = \lim_{r_A \to 0} \frac{\mathcal{E}}{R_{\text{load}} + r_A} = \frac{12.0\text{ V}}{24.0\ \Omega + 0\ \Omega} = 0.500\text{ A}


Part (b): Behavior when an Ideal Voltmeter is Placed in Series

  1. Determine the Resulting Circuit Current: A voltmeter is designed to measure potential difference across two points and possesses an extremely high internal resistance (RV→∞R_V \to \infty). If mistakenly placed in series, the total resistance of the single loop becomes: Rtotal=Rload+RVR_{\text{total}} = R_{\text{load}} + R_V

    Evaluating the current in the ideal limit RV→∞R_V \to \infty: Iseries=lim⁡RV→∞ERload+RV=lim⁡RV→∞12.0 V24.0 Ω+RV=0 AI_{\text{series}} = \lim_{R_V \to \infty} \frac{\mathcal{E}}{R_{\text{load}} + R_V} = \lim_{R_V \to \infty} \frac{12.0\text{ V}}{24.0\ \Omega + R_V} = 0\text{ A} The virtually infinite resistance acts as an open circuit, blocking charge flow.

  2. Determine the Voltage Across the Voltmeter: Using the voltage divider formula: Vmeter=E⋅RVRload+RVV_{\text{meter}} = \mathcal{E} \cdot \frac{R_V}{R_{\text{load}} + R_V} Dividing the numerator and denominator by RVR_V: Vmeter=lim⁡RV→∞E⋅1RloadRV+1=12.0 V⋅10+1=12.0 VV_{\text{meter}} = \lim_{R_V \to \infty} \mathcal{E} \cdot \frac{1}{\frac{R_{\text{load}}}{R_V} + 1} = 12.0\text{ V} \cdot \frac{1}{0 + 1} = 12.0\text{ V}

    Alternatively, using Ohm's law across the load resistor: since Iseries=0 AI_{\text{series}} = 0\text{ A}, the potential drop across the load is Vload=IseriesRload=0 VV_{\text{load}} = I_{\text{series}} R_{\text{load}} = 0\text{ V}. By Kirchhoff's voltage law: Vmeter=E−Vload=12.0 V−0 V=12.0 VV_{\text{meter}} = \mathcal{E} - V_{\text{load}} = 12.0\text{ V} - 0\text{ V} = 12.0\text{ V}


Part (c): Conceptual Distinction Between Voltage and Current

  • Voltage (Electric Potential Difference) is the measure of electric potential energy per unit charge between two points in space: ΔV=ΔUq\Delta V = \frac{\Delta U}{q} It represents the electrostatic "push" or driving force established by the source, which exists whether charges are moving or stationary.
  • Current is the actual rate of flow of electric charge: I=dqdtI = \frac{\mathrm{d}q}{\mathrm{d}t} Current requires both a potential difference and a continuous conducting pathway with finite resistance.
  • Key Insight & Common Pitfall: A common misconception is that zero current implies zero voltage. This circuit shows that an open circuit (or an ideal voltmeter with RV→∞R_V \to \infty) prevents charge from circulating (I=0 AI = 0\text{ A}), yet the full potential difference of 12.0 V12.0\text{ V} remains established across the break in the circuit.

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student assumes that zero current through the circuit implies zero voltage across the voltmeter terminals by misapplying Ohm's law V = I*R to the meter without considering its infinite resistance.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    Rtotal=24.0 Ω+0 Ω=24.0 Ω  ⟹  I=12.0 V/24.0 Ω=0.500 AR_{\text{total}} = 24.0\ \Omega + 0\ \Omega = 24.0\ \Omega \implies I = 12.0\text{ V} / 24.0\ \Omega = 0.500\text{ A}

  2. Step 2

    Rtotal=24.0 Ω+∞=∞  ⟹  Iseries=12.0 V/∞=0 AR_{\text{total}} = 24.0\ \Omega + \infty = \infty \implies I_{\text{series}} = 12.0\text{ V} / \infty = 0\text{ A}

  3. Step 3

    Vmeter=Iseries×Rload=0 VV_{\text{meter}} = I_{\text{series}} \times R_{\text{load}} = 0\text{ V}

    Correct

    Vmeter=E−IseriesRload=12.0 V−(0 A)(24.0 Ω)=12.0 VV_{\text{meter}} = \mathcal{E} - I_{\text{series}} R_{\text{load}} = 12.0\text{ V} - (0\text{ A})(24.0\ \Omega) = 12.0\text{ V}

    You calculated the voltage drop across the load resistor rather than the potential difference across the voltmeter terminals. Applying Kirchhoff's voltage law shows that with zero drop across the load resistor, the full 12.0 V12.0\text{ V} appears across the voltmeter.

  4. Step 4

    Voltage requires current flow to register on a meter, so when current stops the measured voltage drops to zero.

    Correct

    Voltage represents the electric potential difference between two points and exists independently of current flow; an open circuit stops current (I=0 AI = 0\text{ A}) while sustaining the full source voltage across the gap.

    Voltage is an electric potential difference (energy per unit charge), not a byproduct of current. It can exist across an open circuit even when charge cannot circulate.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly applied the ideal ammeter limit rA→0 Ωr_A \to 0\ \Omega to find the normal circuit current.

You correctly recognized that an ideal voltmeter in series introduces infinite resistance and drives circuit current to zero.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Equating Zero Current with Zero Voltage

You equated the voltage across the voltmeter to the voltage drop across the load resistor (IRloadI R_{\text{load}}).

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated voltage as a quantity that requires moving charges to exist, rather than recognizing voltage as electric potential difference that establishes the push regardless of whether current flows.

REASONING PATH
Your ACEpath teacher’s suggested approach
Voltage as Potential Difference
  • Voltage between two terminals ΔV\Delta V is an electric potential difference that exists even in an open circuit where I=0 AI = 0\text{ A}.

  • Do not assume V=0V = 0 just because I=0I = 0; use Kirchhoff's voltage law or the voltage divider rule to find the potential difference across an open gap.

Applying Kirchhoff's Voltage Law to Open Circuits
  • In a series loop, E=Vresistors+Vgap\mathcal{E} = V_{\text{resistors}} + V_{\text{gap}}. If I=0I = 0, then Vresistors=0V_{\text{resistors}} = 0, meaning Vgap=EV_{\text{gap}} = \mathcal{E}.

  • When a branch has infinite resistance, attribute all source potential to the open gap or voltmeter terminals.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Apply Ohm's law to the load resistor: Vload=IseriesRload=(0 A)(24.0 Ω)=0 VV_{\text{load}} = I_{\text{series}} R_{\text{load}} = (0\text{ A})(24.0\ \Omega) = 0\text{ V}.

  2. Apply Kirchhoff's voltage law around the single loop: E−Vload−Vmeter=0\mathcal{E} - V_{\text{load}} - V_{\text{meter}} = 0.

  3. Solve for the voltmeter reading: Vmeter=E−Vload=12.0 V−0 V=12.0 VV_{\text{meter}} = \mathcal{E} - V_{\text{load}} = 12.0\text{ V} - 0\text{ V} = 12.0\text{ V}.

Final answer

Vmeter=12.0 VV_{\text{meter}} = 12.0\text{ V}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the distinction between electric potential difference (voltage) and the flow rate of charge (current).

  • Practice using Kirchhoff's voltage law on circuits containing open switches or infinite-resistance meters.

  • Remember that an unplugged battery or open circuit still maintains its rated voltage across its terminals.

OverviewACEpath Teacher's Diagnosis

02 The student treats the ideal voltmeter as having negligible resistance like an ammeter, calculating current as though the voltmeter creates a short circuit.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    Rtotal=24.0 Ω+0 Ω=24.0 Ω  ⟹  I=12.0 V/24.0 Ω=0.500 AR_{\text{total}} = 24.0\ \Omega + 0\ \Omega = 24.0\ \Omega \implies I = 12.0\text{ V} / 24.0\ \Omega = 0.500\text{ A}

  2. Step 2

    Rtotal=24.0 Ω+0 Ω=24.0 Ω  ⟹  Iseries=12.0 V/24.0 Ω=0.500 AR_{\text{total}} = 24.0\ \Omega + 0\ \Omega = 24.0\ \Omega \implies I_{\text{series}} = 12.0\text{ V} / 24.0\ \Omega = 0.500\text{ A}

    Correct

    Rtotal=Rload+RV=24.0 Ω+∞→∞  ⟹  Iseries=lim⁡RV→∞12.0 V24.0 Ω+RV=0 AR_{\text{total}} = R_{\text{load}} + R_V = 24.0\ \Omega + \infty \to \infty \implies I_{\text{series}} = \lim_{R_V \to \infty} \frac{12.0\text{ V}}{24.0\ \Omega + R_V} = 0\text{ A}

    An ideal voltmeter has an internal resistance approaching infinity (RV→∞R_V \to \infty), not zero. When placed in series, it acts as an open circuit, reducing the current to 0 A0\text{ A}.

  3. Step 3

    Vmeter=(0.500 A)(0 Ω)=0 VV_{\text{meter}} = (0.500\text{ A})(0\ \Omega) = 0\text{ V}

    Correct

    Vmeter=E−IseriesRload=12.0 V−(0 A)(24.0 Ω)=12.0 VV_{\text{meter}} = \mathcal{E} - I_{\text{series}} R_{\text{load}} = 12.0\text{ V} - (0\text{ A})(24.0\ \Omega) = 12.0\text{ V}

    Because you assumed the voltmeter resistance was 0 Ω0\ \Omega, your terminal voltage calculation evaluated to 0 V0\text{ V} instead of the full battery potential of 12.0 V12.0\text{ V}.

  4. Step 4

    Voltage exists across separated charges independently of whether current flows through the path.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly recalled that an ideal ammeter has zero internal resistance and used it to find the circuit current in part (a).

You clearly understood the core physical principle that electric potential difference can exist without current flowing.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Voltmeter vs Ammeter Internal Resistance Confusion

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You assigned an internal resistance of 0 Ω0\ \Omega to both the ammeter and the voltmeter, conflating an ideal voltmeter's open-circuit behavior (RV→∞R_V \to \infty) with an ideal ammeter's short-circuit behavior (rA→0 Ωr_A \to 0\ \Omega).

REASONING PATH
Your ACEpath teacher’s suggested approach
Ideal Meter Resistances
  • An ideal ammeter has rA=0 Ωr_A = 0\ \Omega (short circuit), whereas an ideal voltmeter has RV=∞ ΩR_V = \infty\ \Omega (open circuit).

  • Always verify which meter is in the circuit before setting internal resistance: zero for ammeters, infinite for voltmeters.

Voltage Across an Open Circuit
  • When no current flows through a loop containing an EMF source, there is no voltage drop across resistors (VR=IR=0V_R = I R = 0), so the entire EMF appears across the open gap.

  • Apply Kirchhoff's loop rule: E−IRload−Vmeter=0\mathcal{E} - I R_{\text{load}} - V_{\text{meter}} = 0, which yields Vmeter=EV_{\text{meter}} = \mathcal{E} when I=0I = 0.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Set the ideal voltmeter resistance to RV→∞R_V \to \infty in the series loop.

  2. Calculate the circuit current: Iseries=lim⁡RV→∞12.0 V24.0 Ω+RV=0 AI_{\text{series}} = \lim_{R_V \to \infty} \frac{12.0\text{ V}}{24.0\ \Omega + R_V} = 0\text{ A}.

  3. Find the potential drop across the load resistor: Vload=IseriesRload=(0 A)(24.0 Ω)=0 VV_{\text{load}} = I_{\text{series}} R_{\text{load}} = (0\text{ A})(24.0\ \Omega) = 0\text{ V}.

  4. Determine the voltmeter terminal voltage using Kirchhoff's voltage law: Vmeter=E−Vload=12.0 V−0 V=12.0 VV_{\text{meter}} = \mathcal{E} - V_{\text{load}} = 12.0\text{ V} - 0\text{ V} = 12.0\text{ V}.

Final answer

(a) I=0.500 AI = 0.500\text{ A}; (b) Iseries=0 AI_{\text{series}} = 0\text{ A}, Vmeter=12.0 VV_{\text{meter}} = 12.0\text{ V}; (c) Voltage represents electric potential difference and exists across open terminals even when I=0 AI = 0\text{ A}.

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the distinct roles and internal resistances of measuring instruments: ammeters must not impede current (R→0R \to 0), while voltmeters must not draw current (R→∞R \to \infty).

  • Practice using the voltage divider equation when resistors or meters with extreme resistance values are placed in series.

Lock it in

Similar question

01

A 1.5 V1.5\text{ V} AA battery sits disconnected on a wooden table. Evaluate (a) the electric current leaving the positive terminal and (b) the voltage across its two terminals.

Answer

(a) I=0 AI = 0\text{ A} because there is no closed conducting circuit. (b) V=1.5 VV = 1.5\text{ V} because the chemical potential difference between the terminals is maintained independently of charge flow.

02

A 20.0 V20.0\text{ V} DC source is connected in series with a 100 Ω100\ \Omega resistor and an open switch. What is the potential difference across (a) the 100 Ω100\ \Omega resistor and (b) the open switch contacts?

Answer

(a) With the switch open, I=0 AI = 0\text{ A}, so VR=IR=(0 A)(100 Ω)=0 VV_R = I R = (0\text{ A})(100\ \Omega) = 0\text{ V}. (b) By Kirchhoff's voltage law, Vswitch=E−VR=20.0 V−0 V=20.0 VV_{\text{switch}} = \mathcal{E} - V_R = 20.0\text{ V} - 0\text{ V} = 20.0\text{ V}.

03

A real voltmeter has an internal resistance of 10.0 MΩ10.0\text{ M}\Omega and is accidentally connected in series with a 120 V120\text{ V} DC source and a 5.0 kΩ5.0\text{ k}\Omega light bulb. Calculate (a) the circuit current and (b) the voltage registered by the voltmeter.

Answer

(a) Rtotal=5.0 kΩ+10.0 MΩ=10.005×106 ΩR_{\text{total}} = 5.0\text{ k}\Omega + 10.0\text{ M}\Omega = 10.005\times 10^6\ \Omega, so I=120 V1.0005×107 Ω≈1.20×10−5 A=12.0 μAI = \frac{120\text{ V}}{1.0005\times 10^7\ \Omega} \approx 1.20\times 10^{-5}\text{ A} = 12.0\ \mu\text{A}. (b) Vmeter=IRV=(1.20×10−5 A)(10.0×106 Ω)≈119.94 V≈120 VV_{\text{meter}} = I R_V = (1.20\times 10^{-5}\text{ A})(10.0\times 10^6\ \Omega) \approx 119.94\text{ V} \approx 120\text{ V}. Almost the entire supply voltage appears across the meter because RV≫RbulbR_V \gg R_{\text{bulb}}.

Loading workspace…