Resources

A heavy industrial block of mass M=420 kgM = 420\text{ kg} is released from rest from a vertical drop height of h=0.650 mh = 0.650\text{ m} directly above a rigid top cap fastened to an upright solid steel compression column of original height L0=1.80 mL_0 = 1.80\text{ m} and cross-sectional area A=6.50×10−4 m2A = 6.50 \times 10^{-4}\text{ m}^2. The steel has a Young's modulus of E=2.00×1011 PaE = 2.00 \times 10^{11}\text{ Pa}. Assuming the collision is non-destructive, the cap has negligible mass, and taking g=9.80 m/s2g = 9.80\text{ m/s}^2: (a) use energy conservation coupling gravitational potential energy with elastic strain energy to formulate and solve the quadratic equation for the maximum dynamic vertical compression ΔLmax⁡\Delta L_{\max}, and (b) determine the maximum compressive stress σmax⁡\sigma_{\max} experienced during this dynamic impact.

Answer and steps

Final answer

(a) ΔLmax⁡=8.68×10−3 m=8.68 mm\Delta L_{\max} = 8.68 \times 10^{-3}\text{ m} = 8.68\text{ mm}; (b) σmax⁡=9.64×108 Pa\sigma_{\max} = 9.64 \times 10^8\text{ Pa}

Steps

Part (a): Maximum Dynamic Compression ΔLmax⁡\Delta L_{\max}

  1. Model the column as an elastic spring: Under axial loading, a uniform column follows Hooke's law: F=(EAL0)ΔL=kΔLF = \left(\frac{E A}{L_0}\right) \Delta L = k \Delta L where the equivalent stiffness kk is: k=EAL0=(2.00×1011 Pa)(6.50×10−4 m2)1.80 m=1.30×1081.80≈7.222×107 N/mk = \frac{E A}{L_0} = \frac{(2.00 \times 10^{11}\text{ Pa})(6.50 \times 10^{-4}\text{ m}^2)}{1.80\text{ m}} = \frac{1.30 \times 10^8}{1.80} \approx 7.222 \times 10^7\text{ N/m}
  2. Apply conservation of mechanical energy: The block starts from rest at height hh above the column and momentary comes to rest at the point of maximum compression ΔLmax⁡\Delta L_{\max}.

    Taking the lowest position (maximum compression point) as the reference for gravitational potential energy:

    • Initial mechanical energy: Ei=Mg(h+ΔLmax⁡)E_i = M g (h + \Delta L_{\max})
    • Final mechanical energy stored entirely as elastic strain energy: Ef=12k(ΔLmax⁡)2E_f = \frac{1}{2} k (\Delta L_{\max})^2

    Equating initial and final mechanical energy: Mg(h+ΔLmax⁡)=12k(ΔLmax⁡)2M g (h + \Delta L_{\max}) = \frac{1}{2} k (\Delta L_{\max})^2

    Common Pitfall: Neglecting the additional gravitational potential energy lost during the column's deformation (MgΔLmax⁡M g \Delta L_{\max}) underestimates the total energy transferred into the column.

  3. Set up and solve the quadratic equation: Rearrange the energy equation into standard quadratic form: 12k(ΔLmax⁡)2−MgΔLmax⁡−Mgh=0\frac{1}{2} k (\Delta L_{\max})^2 - M g \Delta L_{\max} - M g h = 0

    Divide through by 12k\frac{1}{2} k: (ΔLmax⁡)2−(2Mgk)ΔLmax⁡−2Mghk=0(\Delta L_{\max})^2 - \left(\frac{2 M g}{k}\right) \Delta L_{\max} - \frac{2 M g h}{k} = 0

    Calculate the coefficients using Mg=(420 kg)(9.80 m/s2)=4116 NM g = (420\text{ kg})(9.80\text{ m/s}^2) = 4116\text{ N}: 2Mgk=2(4116 N)7.222×107 N/m≈1.140×10−4 m\frac{2 M g}{k} = \frac{2(4116\text{ N})}{7.222 \times 10^7\text{ N/m}} \approx 1.140 \times 10^{-4}\text{ m} 2Mghk=(1.140×10−4 m)(0.650 m)≈7.409×10−5 m2\frac{2 M g h}{k} = (1.140 \times 10^{-4}\text{ m})(0.650\text{ m}) \approx 7.409 \times 10^{-5}\text{ m}^2

    Substituting into the quadratic formula and taking the positive physical root: ΔLmax⁡=1.140×10−4+(1.140×10−4)2+4(7.409×10−5)2\Delta L_{\max} = \frac{1.140 \times 10^{-4} + \sqrt{(1.140 \times 10^{-4})^2 + 4(7.409 \times 10^{-5})}}{2} ΔLmax⁡≈1.140×10−4+1.30×10−8+2.964×10−42≈1.140×10−4+0.017222≈8.68×10−3 m\Delta L_{\max} \approx \frac{1.140 \times 10^{-4} + \sqrt{1.30 \times 10^{-8} + 2.964 \times 10^{-4}}}{2} \approx \frac{1.140 \times 10^{-4} + 0.01722}{2} \approx 8.68 \times 10^{-3}\text{ m}

    Therefore, ΔLmax⁡=8.68×10−3 m=8.68 mm\Delta L_{\max} = 8.68 \times 10^{-3}\text{ m} = 8.68\text{ mm}.


Part (b): Maximum Compressive Stress σmax⁡\sigma_{\max}

  1. Calculate the maximum strain: εmax⁡=ΔLmax⁡L0=8.68×10−3 m1.80 m≈4.822×10−3\varepsilon_{\max} = \frac{\Delta L_{\max}}{L_0} = \frac{8.68 \times 10^{-3}\text{ m}}{1.80\text{ m}} \approx 4.822 \times 10^{-3}
  2. Determine the maximum compressive stress: Using Hooke's law, σmax⁡=Eεmax⁡\sigma_{\max} = E \varepsilon_{\max}: σmax⁡=(2.00×1011 Pa)(4.822×10−3)≈9.64×108 Pa\sigma_{\max} = (2.00 \times 10^{11}\text{ Pa})(4.822 \times 10^{-3}) \approx 9.64 \times 10^8\text{ Pa}

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student ignores the additional gravitational potential energy lost during the compression ΔL_max, equating M*g*h directly to elastic strain energy.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    k=E⋅AL0=(2.00×1011)(6.50×10−4)1.80=7.222×107 N/mk = \frac{E \cdot A}{L_0} = \frac{(2.00 \times 10^{11})(6.50 \times 10^{-4})}{1.80} = 7.222 \times 10^7\text{ N/m}

  2. Step 2

    M⋅g⋅h=12⋅k⋅(ΔLmax⁡)2  ⟹  (420)(9.80)(0.650)=0.5⋅(7.222×107)⋅(ΔLmax⁡)2  ⟹  2675.4=(3.611×107)⋅(ΔLmax⁡)2  ⟹  ΔLmax⁡=2675.43.611×107=8.61×10−3 mM \cdot g \cdot h = \frac{1}{2} \cdot k \cdot (\Delta L_{\max})^2 \implies (420)(9.80)(0.650) = 0.5 \cdot (7.222 \times 10^7) \cdot (\Delta L_{\max})^2 \implies 2675.4 = (3.611 \times 10^7) \cdot (\Delta L_{\max})^2 \implies \Delta L_{\max} = \sqrt{\frac{2675.4}{3.611 \times 10^7}} = 8.61 \times 10^{-3}\text{ m}

    Correct

    Mg(h+ΔLmax⁡)=12k(ΔLmax⁡)2  ⟹  (ΔLmax⁡)2−(2Mgk)ΔLmax⁡−2Mghk=0  ⟹  ΔLmax⁡≈8.68×10−3 mM g (h + \Delta L_{\max}) = \frac{1}{2} k (\Delta L_{\max})^2 \implies (\Delta L_{\max})^2 - \left(\frac{2 M g}{k}\right) \Delta L_{\max} - \frac{2 M g h}{k} = 0 \implies \Delta L_{\max} \approx 8.68 \times 10^{-3}\text{ m}

    As the block compresses the column by ΔLmax⁡\Delta L_{\max}, it continues to lose gravitational potential energy. The total vertical displacement is h+ΔLmax⁡h + \Delta L_{\max}, which creates a quadratic equation rather than a direct square root.

  3. Step 3

    σmax⁡=E⋅ΔLmax⁡L0=(2.00×1011)(8.61×10−3)1.80=9.57×108 Pa\sigma_{\max} = \frac{E \cdot \Delta L_{\max}}{L_0} = \frac{(2.00 \times 10^{11})(8.61 \times 10^{-3})}{1.80} = 9.57 \times 10^8\text{ Pa}

    Correct

    σmax⁡=EΔLmax⁡L0=(2.00×1011 Pa)(8.68×10−3 m)1.80 m≈9.64×108 Pa\sigma_{\max} = \frac{E \Delta L_{\max}}{L_0} = \frac{(2.00 \times 10^{11}\text{ Pa})(8.68 \times 10^{-3}\text{ m})}{1.80\text{ m}} \approx 9.64 \times 10^8\text{ Pa}

    Your formula and calculation method for maximum compressive stress were completely sound, but substituting the underestimated ΔLmax⁡\Delta L_{\max} produced an incorrect numerical result.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly modeled the elastic column as an axial spring with equivalent stiffness k=EAL0k = \frac{EA}{L_0}.

You used the correct constitutive relation σ=EΔLL0\sigma = \frac{E \Delta L}{L_0} to evaluate compressive stress.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Neglected displacement in potential energy

none

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated the gravitational potential energy drop as solely MghM g h, forgetting that gravity continues to do positive work through the entire downward displacement h+ΔLmax⁡h + \Delta L_{\max} until the block momentarily stops.

REASONING PATH
Your ACEpath teacher’s suggested approach
Reference level for dynamic impact
  • For a vertical fall onto an elastic body, total gravitational potential energy lost is ΔUg=Mg(h+Δy)\Delta U_g = M g (h + \Delta y), where Δy\Delta y is the maximum deformation.

  • Always establish your zero potential energy reference at the lowest point of travel (maximum compression) so the total fall height includes both the free-fall distance and the deformation distance.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Write the complete energy balance from release to maximum compression: Mg(h+ΔLmax⁡)=12k(ΔLmax⁡)2M g (h + \Delta L_{\max}) = \frac{1}{2} k (\Delta L_{\max})^2.

  2. Rearrange into standard quadratic form: (ΔLmax⁡)2−2MgkΔLmax⁡−2Mghk=0(\Delta L_{\max})^2 - \frac{2 M g}{k} \Delta L_{\max} - \frac{2 M g h}{k} = 0.

  3. Substitute the numerical values 2Mgk=2(4116)7.222×107≈1.140×10−4 m\frac{2 M g}{k} = \frac{2(4116)}{7.222 \times 10^7} \approx 1.140 \times 10^{-4}\text{ m} and 2Mghk≈7.409×10−5 m2\frac{2 M g h}{k} \approx 7.409 \times 10^{-5}\text{ m}^2.

  4. Solve for the positive root: ΔLmax⁡=1.140×10−4+(1.140×10−4)2+4(7.409×10−5)2≈8.68×10−3 m\Delta L_{\max} = \frac{1.140 \times 10^{-4} + \sqrt{(1.140 \times 10^{-4})^2 + 4(7.409 \times 10^{-5})}}{2} \approx 8.68 \times 10^{-3}\text{ m}.

  5. Compute maximum stress: σmax⁡=EΔLmax⁡L0=(2.00×1011 Pa)(8.68×10−3 m)1.80 m≈9.64×108 Pa\sigma_{\max} = \frac{E \Delta L_{\max}}{L_0} = \frac{(2.00 \times 10^{11}\text{ Pa})(8.68 \times 10^{-3}\text{ m})}{1.80\text{ m}} \approx 9.64 \times 10^8\text{ Pa}.

Final answer

(a) ΔLmax⁡=8.68×10−3 m=8.68 mm\Delta L_{\max} = 8.68 \times 10^{-3}\text{ m} = 8.68\text{ mm}; (b) σmax⁡=9.64×108 Pa\sigma_{\max} = 9.64 \times 10^8\text{ Pa}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review dynamic load factor formulations, noting how n=1+1+2hΔLstn = 1 + \sqrt{1 + \frac{2h}{\Delta L_{\text{st}}}} accounts for the deformation height.

  • Practice setting up energy conservation equations with vertical springs by explicitly sketching the initial, contact, and maximum-compression positions.

OverviewACEpath Teacher's Diagnosis

02 The student forgets the factor of 1/2 in the elastic strain energy formula, using k*(ΔL_max)² instead of (1/2)*k*(ΔL_max)².

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    k=E⋅AL0=(2.00×1011)(6.50×10−4)1.80=7.222×107 N/mk = \frac{E \cdot A}{L_0} = \frac{(2.00 \times 10^{11})(6.50 \times 10^{-4})}{1.80} = 7.222 \times 10^7\text{ N/m}

  2. Step 2

    M⋅g⋅(h+ΔLmax⁡)=k⋅(ΔLmax⁡)2  ⟹  4116⋅(0.650+ΔLmax⁡)=(7.222×107)⋅(ΔLmax⁡)2  ⟹  (7.222×107)(ΔLmax⁡)2−4116ΔLmax⁡−2675.4=0M \cdot g \cdot (h + \Delta L_{\max}) = k \cdot (\Delta L_{\max})^2 \implies 4116 \cdot (0.650 + \Delta L_{\max}) = (7.222 \times 10^7) \cdot (\Delta L_{\max})^2 \implies (7.222 \times 10^7)(\Delta L_{\max})^2 - 4116 \Delta L_{\max} - 2675.4 = 0

    Correct

    Mg(h+ΔLmax⁡)=12k(ΔLmax⁡)2  ⟹  12(7.222×107)(ΔLmax⁡)2−4116ΔLmax⁡−2675.4=0M g (h + \Delta L_{\max}) = \frac{1}{2} k (\Delta L_{\max})^2 \implies \frac{1}{2}(7.222 \times 10^7)(\Delta L_{\max})^2 - 4116 \Delta L_{\max} - 2675.4 = 0

    You omitted the factor of 12\frac{1}{2} in the elastic potential energy term on the right-hand side. Elastic strain energy is Ue=12k(ΔL)2U_e = \frac{1}{2} k (\Delta L)^2, because restoring force increases linearly from 00 to kΔLk \Delta L.

  3. Step 3

    ΔLmax⁡=4116+41162−4(7.222×107)(−2675.4)2⋅7.222×107=6.11×10−3 m\Delta L_{\max} = \frac{4116 + \sqrt{4116^2 - 4(7.222 \times 10^7)(-2675.4)}}{2 \cdot 7.222 \times 10^7} = 6.11 \times 10^{-3}\text{ m}

    Correct

    ΔLmax⁡=4116+41162−4(3.611×107)(−2675.4)2(3.611×107)≈8.68×10−3 m\Delta L_{\max} = \frac{4116 + \sqrt{4116^2 - 4(3.611 \times 10^7)(-2675.4)}}{2(3.611 \times 10^7)} \approx 8.68 \times 10^{-3}\text{ m}

    You applied the quadratic formula correctly to your equation, but the numerical result is smaller than the true value due to the missing 12\frac{1}{2} in the quadratic term.

  4. Step 4

    σmax⁡=E⋅ΔLmax⁡L0=(2.00×1011)(6.11×10−3)1.80=6.79×108 Pa\sigma_{\max} = \frac{E \cdot \Delta L_{\max}}{L_0} = \frac{(2.00 \times 10^{11})(6.11 \times 10^{-3})}{1.80} = 6.79 \times 10^8\text{ Pa}

    Correct

    σmax⁡=E(ΔLmax⁡L0)=(2.00×1011 Pa)(8.68×10−3 m)1.80 m≈9.64×108 Pa\sigma_{\max} = E \left(\frac{\Delta L_{\max}}{L_0}\right) = \frac{(2.00 \times 10^{11}\text{ Pa})(8.68 \times 10^{-3}\text{ m})}{1.80\text{ m}} \approx 9.64 \times 10^8\text{ Pa}

    Your stress formula is correct, but your final numerical value carries over the error from ΔLmax⁡\Delta L_{\max}.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly calculated the axial spring stiffness kk of the steel column.

You recognized that gravitational potential energy continues to decrease through the full drop distance h+ΔLmax⁡h + \Delta L_{\max}.

You correctly used Hooke's law in the form σ=EΔLL0\sigma = E \frac{\Delta L}{L_0} to relate strain to stress.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Missing 1/2 in Elastic Potential Energy

You wrote Ue=k(ΔL)2U_e = k(\Delta L)^2 instead of Ue=12k(ΔL)2U_e = \frac{1}{2}k(\Delta L)^2.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing force with energy or neglecting the integration of a linearly varying restoring force: while spring force is F=kΔLF = k \Delta L, the work done (stored elastic strain energy) represents the triangular area under the FF vs. ΔL\Delta L curve, which requires the factor of 12\frac{1}{2}.

REASONING PATH
Your ACEpath teacher’s suggested approach
Recall Elastic Strain Energy
  • Ue=∫0ΔLkx dx=12k(ΔL)2=12EAL0(ΔL)2U_e = \int_0^{\Delta L} k x\,dx = \frac{1}{2} k (\Delta L)^2 = \frac{1}{2} \frac{E A}{L_0} (\Delta L)^2

  • Always verify that any quadratic deformation energy term has the coefficient 12\frac{1}{2}.

Quadratic Form Setup
  • For vertical impact from height hh, the energy balance is 12k(ΔL)2−MgΔL−Mgh=0\frac{1}{2}k(\Delta L)^2 - Mg\Delta L - Mgh = 0.

  • Ensure the leading coefficient is 12k\frac{1}{2}k (or 11 if dividing through by 12k\frac{1}{2}k) before applying the quadratic formula.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Write the corrected mechanical energy conservation equation: Mg(h+ΔLmax⁡)=12k(ΔLmax⁡)2M g (h + \Delta L_{\max}) = \frac{1}{2} k (\Delta L_{\max})^2.

  2. Substitute numerical values: 4116(0.650+ΔLmax⁡)=12(7.222×107)(ΔLmax⁡)2=3.611×107(ΔLmax⁡)24116(0.650 + \Delta L_{\max}) = \frac{1}{2}(7.222 \times 10^7)(\Delta L_{\max})^2 = 3.611 \times 10^7 (\Delta L_{\max})^2.

  3. Rearrange into standard quadratic form: 3.611×107(ΔLmax⁡)2−4116ΔLmax⁡−2675.4=03.611 \times 10^7 (\Delta L_{\max})^2 - 4116 \Delta L_{\max} - 2675.4 = 0.

  4. Solve for the positive physical root: ΔLmax⁡=4116+41162−4(3.611×107)(−2675.4)2(3.611×107)≈8.68×10−3 m=8.68 mm\Delta L_{\max} = \frac{4116 + \sqrt{4116^2 - 4(3.611 \times 10^7)(-2675.4)}}{2(3.611 \times 10^7)} \approx 8.68 \times 10^{-3}\text{ m} = 8.68\text{ mm}.

  5. Compute dynamic stress: σmax⁡=EΔLmax⁡L0=(2.00×1011 Pa)(8.68×10−3 m)1.80 m≈9.64×108 Pa\sigma_{\max} = \frac{E \Delta L_{\max}}{L_0} = \frac{(2.00 \times 10^{11}\text{ Pa})(8.68 \times 10^{-3}\text{ m})}{1.80\text{ m}} \approx 9.64 \times 10^8\text{ Pa}.

Final answer

(a) ΔLmax⁡=8.68×10−3 m=8.68 mm\Delta L_{\max} = 8.68 \times 10^{-3}\text{ m} = 8.68\text{ mm}; (b) σmax⁡=9.64×108 Pa\sigma_{\max} = 9.64 \times 10^8\text{ Pa}

NEXT STEPS
Final Takeaways from Your Teacher
  • Double-check that all quadratic potential energy formulas (like 12kx2\frac{1}{2}kx^2 and 12Iω2\frac{1}{2}I\omega^2) include their factor of 12\frac{1}{2}.

  • Practice vertical impact problems to reinforce pairing the total fall height h+ΔLh + \Delta L with the correct strain energy expression.

OverviewACEpath Teacher's Diagnosis

03 The student calculates static compression under the weight M*g instead of solving the dynamic impact equation.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    k=E⋅AL0=(2.00×1011)(6.50×10−4)1.80=7.222×107 N/mk = \frac{E \cdot A}{L_0} = \frac{(2.00 \times 10^{11})(6.50 \times 10^{-4})}{1.80} = 7.222 \times 10^7\text{ N/m}

  2. Step 2

    ΔLmax⁡=M⋅gk=(420)(9.80)7.222×107=5.70×10−5 m\Delta L_{\max} = \frac{M \cdot g}{k} = \frac{(420)(9.80)}{7.222 \times 10^7} = 5.70 \times 10^{-5}\text{ m}

    Correct

    Mg(h+ΔLmax⁡)=12k(ΔLmax⁡)2  ⟹  ΔLmax⁡≈8.68×10−3 mM g (h + \Delta L_{\max}) = \frac{1}{2} k (\Delta L_{\max})^2 \implies \Delta L_{\max} \approx 8.68 \times 10^{-3}\text{ m}

    You used the static deflection formula ΔLst=Mgk\Delta L_{\text{st}} = \frac{M g}{k}. Because the mass is dropped from a height h=0.650 mh = 0.650\text{ m}, you must equate the total loss in gravitational potential energy Mg(h+ΔLmax⁡)M g (h + \Delta L_{\max}) to the stored elastic strain energy 12k(ΔLmax⁡)2\frac{1}{2} k (\Delta L_{\max})^2.

  3. Step 3

    σmax⁡=E⋅ΔLmax⁡L0=(2.00×1011)(5.70×10−5)1.80=6.33×106 Pa\sigma_{\max} = \frac{E \cdot \Delta L_{\max}}{L_0} = \frac{(2.00 \times 10^{11})(5.70 \times 10^{-5})}{1.80} = 6.33 \times 10^6\text{ Pa}

    Correct

    σmax⁡=EΔLmax⁡L0=(2.00×1011 Pa)(8.68×10−3 m)1.80 m≈9.64×108 Pa\sigma_{\max} = \frac{E \Delta L_{\max}}{L_0} = \frac{(2.00 \times 10^{11}\text{ Pa})(8.68 \times 10^{-3}\text{ m})}{1.80\text{ m}} \approx 9.64 \times 10^8\text{ Pa}

    Your formula relating axial stress to deformation is correct, but your numerical result is affected by the incorrect value of ΔLmax⁡\Delta L_{\max} from Step 2.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly derived the column stiffness from Young's modulus, area, and length.

You used the correct constitutive relation σ=EΔLL0\sigma = \frac{E \Delta L}{L_0} to compute stress from strain.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Static vs. Dynamic Loading Confusion

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated an impact drop problem as a static equilibrium problem, neglecting the kinetic energy gained during free fall from height hh and the conservation of mechanical energy.

REASONING PATH
Your ACEpath teacher’s suggested approach
Identify Dynamic Impact
  • Whenever an object falls from a height h>0h > 0 onto an elastic structure, the peak force and compression exceed the static weight MgM g.

  • Check if the object is released from a height above the contact point; if so, apply conservation of mechanical energy rather than static force balance.

Energy Balance Formulation
  • Initial gravitational potential energy relative to the lowest point equals the maximum elastic strain energy: Mg(h+ΔLmax⁡)=12k(ΔLmax⁡)2M g (h + \Delta L_{\max}) = \frac{1}{2} k (\Delta L_{\max})^2.

  • Set up a quadratic equation in ΔLmax⁡\Delta L_{\max}, including both the drop height hh and the additional downward deflection ΔLmax⁡\Delta L_{\max}.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Set up the conservation of energy equation: Mg(h+ΔLmax⁡)=12k(ΔLmax⁡)2M g (h + \Delta L_{\max}) = \frac{1}{2} k (\Delta L_{\max})^2.

  2. Rearrange into standard quadratic form: 12(7.222×107)(ΔLmax⁡)2−(4116)ΔLmax⁡−(4116)(0.650)=0\frac{1}{2}(7.222 \times 10^7)(\Delta L_{\max})^2 - (4116)\Delta L_{\max} - (4116)(0.650) = 0.

  3. Solve for the positive root: ΔLmax⁡≈8.68×10−3 m=8.68 mm\Delta L_{\max} \approx 8.68 \times 10^{-3}\text{ m} = 8.68\text{ mm}.

  4. Substitute ΔLmax⁡\Delta L_{\max} into the maximum stress equation: σmax⁡=EΔLmax⁡L0=(2.00×1011 Pa)(8.68×10−3 m)1.80 m≈9.64×108 Pa\sigma_{\max} = \frac{E \Delta L_{\max}}{L_0} = \frac{(2.00 \times 10^{11}\text{ Pa})(8.68 \times 10^{-3}\text{ m})}{1.80\text{ m}} \approx 9.64 \times 10^8\text{ Pa}.

Final answer

(a) ΔLmax⁡=8.68×10−3 m\Delta L_{\max} = 8.68 \times 10^{-3}\text{ m}; (b) σmax⁡=9.64×108 Pa\sigma_{\max} = 9.64 \times 10^8\text{ Pa}

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice formulating mechanical energy balance for falling masses onto vertical springs.

  • Compare static deflection ΔLst=Mgk\Delta L_{\text{st}} = \frac{M g}{k} with dynamic impact deflection to understand the impact factor n=1+1+2hΔLstn = 1 + \sqrt{1 + \frac{2h}{\Delta L_{\text{st}}}}.

Lock it in

Similar question

01

A 20 kg20\text{ kg} package is dropped from a height of h=0.80 mh = 0.80\text{ m} onto a vertical spring with stiffness k=4000 N/mk = 4000\text{ N/m}. Taking g=9.8 m/s2g = 9.8\text{ m/s}^2, find the maximum compression xmax⁡x_{\max} of the spring.

Answer

xmax⁡=0.142 mx_{\max} = 0.142\text{ m}. From energy conservation, Mg(h+x)=12kx2  ⟹  2000x2−196x−156.8=0  ⟹  x2−0.098x−0.0784=0M g (h + x) = \frac{1}{2} k x^2 \implies 2000 x^2 - 196 x - 156.8 = 0 \implies x^2 - 0.098 x - 0.0784 = 0. Solving the quadratic gives xmax⁡=0.098+0.0982+4(0.0784)2≈0.142 mx_{\max} = \frac{0.098 + \sqrt{0.098^2 + 4(0.0784)}}{2} \approx 0.142\text{ m}.

02

A solid cylindrical rod of length L0=1.20 mL_0 = 1.20\text{ m}, area A=4.0×10−4 m2A = 4.0 \times 10^{-4}\text{ m}^2, and Young's modulus E=1.0×1011 PaE = 1.0 \times 10^{11}\text{ Pa} stands vertically. A mass of 250 kg250\text{ kg} is dropped onto it from rest at height h=0.40 mh = 0.40\text{ m}. Calculate the maximum dynamic axial compression ΔLmax⁡\Delta L_{\max} of the rod (g=9.8 m/s2g = 9.8\text{ m/s}^2).

Answer

ΔLmax⁡=7.74×10−3 m\Delta L_{\max} = 7.74 \times 10^{-3}\text{ m} (7.74 mm7.74\text{ mm}). Equivalent stiffness k=EAL0=(1.0×1011)(4.0×10−4)1.20=3.333×107 N/mk = \frac{E A}{L_0} = \frac{(1.0 \times 10^{11})(4.0 \times 10^{-4})}{1.20} = 3.333 \times 10^7\text{ N/m}. Energy conservation gives Mg(h+ΔL)=12k(ΔL)2M g (h + \Delta L) = \frac{1}{2} k (\Delta L)^2. Rearranging: (ΔL)2−1.470×10−4ΔL−5.880×10−5=0(\Delta L)^2 - 1.470 \times 10^{-4} \Delta L - 5.880 \times 10^{-5} = 0. Solving the quadratic yields ΔLmax⁡≈7.74×10−3 m\Delta L_{\max} \approx 7.74 \times 10^{-3}\text{ m}.

03

In a dynamic impact test, a mass MM drops from height hh onto an elastic member of stiffness kk. Show that the dynamic impact factor n=xmax⁡xstn = \frac{x_{\max}}{x_{\text{st}}} (where xst=Mgkx_{\text{st}} = \frac{M g}{k}) can be written as n=1+1+2hxstn = 1 + \sqrt{1 + \frac{2h}{x_{\text{st}}}}, and evaluate nn if h=10xsth = 10 x_{\text{st}}.

Answer

n≈5.58n \approx 5.58. From Mg(h+x)=12kx2M g (h + x) = \frac{1}{2} k x^2, divide through by MgM g: h+x=kx22Mg=x22xsth + x = \frac{k x^2}{2 M g} = \frac{x^2}{2 x_{\text{st}}}. Multiply by 2xst\frac{2}{x_{\text{st}}}: (xxst)2−2(xxst)−2hxst=0  ⟹  n2−2n−2hxst=0\left(\frac{x}{x_{\text{st}}}\right)^2 - 2\left(\frac{x}{x_{\text{st}}}\right) - \frac{2h}{x_{\text{st}}} = 0 \implies n^2 - 2n - \frac{2h}{x_{\text{st}}} = 0. Solving for the positive root yields n=1+1+2hxstn = 1 + \sqrt{1 + \frac{2h}{x_{\text{st}}}}. For h=10xsth = 10 x_{\text{st}}, n=1+1+20=1+21≈5.58n = 1 + \sqrt{1 + 20} = 1 + \sqrt{21} \approx 5.58.

Loading workspace…