Resources

In a laboratory experiment using an insulated continuous-flow water calorimeter, an electric immersion heating coil is powered by an adjustable DC power bench. A calibrated digital multimeter measures a potential difference of V=48.2 VV = 48.2\ \text{V} across the coil and a current of I=3.65 AI = 3.65\ \text{A} through it. Water with specific heat capacity c=4.184 J/(g⋅∘C)c = 4.184\ \text{J}/(\text{g}\cdot{^\circ}\text{C}) flows steadily through the chamber at a mass flow rate of dmdt=0.650 g/s\frac{dm}{dt} = 0.650\ \text{g/s}. Assuming that η=92.5%\eta = 92.5\% of the total electrical power is absorbed by the fluid stream (with the remainder lost to ambient surroundings): (a) calculate the total electrical power PelecP_{\text{elec}} input to the heating coil. (b) Determine the steady-state temperature rise ΔT=Tout−Tin\Delta T = T_{\text{out}} - T_{\text{in}} of the flowing water.

Answer and steps

Final answer

(a) Pelec=176 WP_{\text{elec}} = 176\ \text{W}; (b) ΔT=59.8 ∘C\Delta T = 59.8\ {^\circ}\text{C}

Steps

Part (a): Total Electrical Power Input

The electrical power PelecP_{\text{elec}} delivered to a resistive heating element is given by the product of the potential difference VV across it and the current II passing through it:

Pelec=V⋅IP_{\text{elec}} = V \cdot I

Substitute the given values into the equation:

Pelec=(48.2 V)⋅(3.65 A)=175.93 WP_{\text{elec}} = (48.2\ \text{V}) \cdot (3.65\ \text{A}) = 175.93\ \text{W}

Rounding to three significant figures gives:

Pelec=176 WP_{\text{elec}} = 176\ \text{W}


Part (b): Steady-State Temperature Rise of the Water

  1. Determine the useful thermal power absorbed by the water:

    Only a fraction η\eta of the electrical power enters the water stream, with the rest dissipated to the surroundings:

    Ptherm=η⋅PelecP_{\text{therm}} = \eta \cdot P_{\text{elec}}

    Ptherm=0.925⋅175.93 W≈162.74 WP_{\text{therm}} = 0.925 \cdot 175.93\ \text{W} \approx 162.74\ \text{W}

  2. Relate thermal power to mass flow rate and temperature rise:

    In a steady-state continuous-flow calorimeter, the rate of heat absorption dQdt=Ptherm\frac{dQ}{dt} = P_{\text{therm}} increases the temperature of the flowing mass:

    Ptherm=dmdt⋅c⋅ΔTP_{\text{therm}} = \frac{dm}{dt} \cdot c \cdot \Delta T

    where:

    • dmdt=0.650 g/s\frac{dm}{dt} = 0.650\ \text{g/s} is the mass flow rate,
    • c=4.184 J/(g⋅∘C)c = 4.184\ \text{J}/(\text{g}\cdot{^\circ}\text{C}) is the specific heat capacity of water,
    • ΔT=Tout−Tin\Delta T = T_{\text{out}} - T_{\text{in}} is the temperature rise.
  3. Solve for ΔT\Delta T:

    ΔT=Ptherm(dmdt)⋅c\Delta T = \frac{P_{\text{therm}}}{\left(\frac{dm}{dt}\right) \cdot c}

    Substitute the numerical values:

    ΔT=162.74 J/s(0.650 g/s)⋅(4.184 J/(g⋅∘C))\Delta T = \frac{162.74\ \text{J/s}}{(0.650\ \text{g/s}) \cdot (4.184\ \text{J}/(\text{g}\cdot{^\circ}\text{C}))}

    ΔT=162.742.7196 ∘C≈59.8 ∘C\Delta T = \frac{162.74}{2.7196}\ ^\circ\text{C} \approx 59.8\ ^\circ\text{C}

(Note on unit consistency: Expressing mass flow rate in g/s\text{g/s} aligns directly with cc in J/(g⋅∘C)\text{J}/(\text{g}\cdot{^\circ}\text{C}), so the mass units cancel cleanly without converting to kilograms.)

Typical errors

OverviewACEpath Teacher's Diagnosis

01 A student neglects the 92.5% efficiency factor and assumes 100% of electrical power is absorbed by water, resulting in an overestimated temperature rise of 64.7 °C.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    Pelec=V×I  ⟹  Pelec=48.2×3.65=175.93 WP_{\text{elec}} = V \times I \implies P_{\text{elec}} = 48.2 \times 3.65 = 175.93\text{ W}

  2. Step 2

    Pabsorbed=Pelec=175.93 WP_{\text{absorbed}} = P_{\text{elec}} = 175.93\text{ W}

    Correct

    Ptherm=η⋅Pelec=0.925×175.93 W≈162.74 WP_{\text{therm}} = \eta \cdot P_{\text{elec}} = 0.925 \times 175.93\text{ W} \approx 162.74\text{ W}

    You assumed 100%100\% of the electrical energy is absorbed by the water stream, but the problem states an efficiency of η=92.5%\eta = 92.5\% with the remaining power lost to the surroundings.

  3. Step 3

    P=dmdt×c×ΔT  ⟹  ΔT=175.930.650×4.184=64.7 ∘CP = \frac{dm}{dt} \times c \times \Delta T \implies \Delta T = \frac{175.93}{0.650 \times 4.184} = 64.7\ ^\circ\text{C}

    Correct

    ΔT=Ptherm(dmdt)c=162.740.650×4.184≈59.8 ∘C\Delta T = \frac{P_{\text{therm}}}{\left(\frac{dm}{dt}\right)c} = \frac{162.74}{0.650 \times 4.184} \approx 59.8\ ^\circ\text{C}

    Your flow calorimetry relationship is set up correctly, but substituting the unscaled electrical power propagated the error to your final temperature rise.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly used the relationship P=V⋅IP = V \cdot I to calculate the electrical power delivered to the immersion heater.

You correctly identified and applied the continuous-flow calorimetry formula relating power, mass flow rate, specific heat, and temperature change.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Omission of efficiency factor

No, this was an omission of a given condition (efficiency η=92.5%\eta = 92.5\%) rather than a simple arithmetic slip.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You equated total electrical input power directly to thermal power absorbed by the fluid, overlooking that real-world calorimeters lose energy to the surroundings unless stated to be ideal.

REASONING PATH
Your ACEpath teacher’s suggested approach
Efficiency in Energy Transfer
  • Puseful=η⋅PinputP_{\text{useful}} = \eta \cdot P_{\text{input}}

  • Always identify whether an efficiency η<1\eta < 1 or heat loss is specified before equating input power to thermal absorption.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Calculate useful thermal power absorbed by the water: Ptherm=η⋅Pelec=0.925×175.93 W=162.74 WP_{\text{therm}} = \eta \cdot P_{\text{elec}} = 0.925 \times 175.93\text{ W} = 162.74\text{ W}

  2. Substitute PthermP_{\text{therm}} into the flow equation: ΔT=Pthermdmdt⋅c=162.74 J/s(0.650 g/s)(4.184 J/(g⋅∘C))\Delta T = \frac{P_{\text{therm}}}{\frac{dm}{dt} \cdot c} = \frac{162.74\text{ J/s}}{(0.650\text{ g/s})(4.184\text{ J}/(\text{g}\cdot{^\circ}\text{C}))}

  3. Evaluate the temperature change: ΔT=162.742.7196 ∘C≈59.8 ∘C\Delta T = \frac{162.74}{2.7196}\ ^\circ\text{C} \approx 59.8\ ^\circ\text{C}

Final answer

(a) Pelec=176 WP_{\text{elec}} = 176\text{ W}; (b) ΔT=59.8 ∘C\Delta T = 59.8\ ^\circ\text{C}

NEXT STEPS
Final Takeaways from Your Teacher
  • Before setting up conservation of energy, check whether an efficiency factor η\eta is given in the problem statement.

  • Label distinct powers clearly (e.g., PelecP_{\text{elec}} vs. PabsorbedP_{\text{absorbed}}) to avoid accidentally setting them equal.

OverviewACEpath Teacher's Diagnosis

02 A student multiplies by the efficiency factor instead of dividing when relating absorbed power to total power, or divides by efficiency in the temperature rise formula, using P_absorbed = P_elec / 0.925 = 190.2 W.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    Pelec=V×I  ⟹  Pelec=48.2×3.65=175.93 WP_{\text{elec}} = V \times I \implies P_{\text{elec}} = 48.2 \times 3.65 = 175.93\text{ W}

  2. Step 2

    Pabsorbed=Pelec/0.925  ⟹  Pabsorbed=175.93/0.925=190.20 WP_{\text{absorbed}} = P_{\text{elec}} / 0.925 \implies P_{\text{absorbed}} = 175.93 / 0.925 = 190.20\text{ W}

    Correct

    Pabsorbed=η⋅Pelec=0.925⋅175.93 W≈162.74 WP_{\text{absorbed}} = \eta \cdot P_{\text{elec}} = 0.925 \cdot 175.93\text{ W} \approx 162.74\text{ W}

    Because only 92.5%92.5\% of the electrical energy reaches the water stream, the absorbed power must be less than the total input power, so you need to multiply by η=0.925\eta = 0.925 rather than divide.

  3. Step 3

    ΔT=Pabsorbed(dm/dt)×c  ⟹  ΔT=190.20/(0.650×4.184)=69.9 ∘C\Delta T = \frac{P_{\text{absorbed}}}{(dm/dt) \times c} \implies \Delta T = 190.20 / (0.650 \times 4.184) = 69.9\text{ }^\circ\text{C}

    Correct

    ΔT=Pabsorbed(dmdt)⋅c=162.74 W(0.650 g/s)⋅(4.184 J/(g⋅∘C))≈59.8 ∘C\Delta T = \frac{P_{\text{absorbed}}}{\left(\frac{dm}{dt}\right) \cdot c} = \frac{162.74\text{ W}}{(0.650\text{ g/s}) \cdot (4.184\text{ J}/(\text{g}\cdot{^\circ}\text{C}))} \approx 59.8\text{ }^\circ\text{C}

    Your thermal flow equation and unit balancing were completely correct, but the final numerical temperature rise was affected by carrying forward the incorrect value of PabsorbedP_{\text{absorbed}}.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly calculated the total electrical power input using P=VIP = VI.

You set up the continuous-flow calorimetry equation relating thermal power to mass flow rate, specific heat, and temperature rise correctly.

You handled the mass and energy units consistently without needing unnecessary conversions.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Inverted efficiency relationship

Dividing total power by the fractional efficiency rather than multiplying by it.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You confused the relationship between total input power and useful absorbed power. Efficiency represents the fraction of input power converted into useful output, so Puseful=η⋅PinputP_{\text{useful}} = \eta \cdot P_{\text{input}}. Because η<1\eta < 1, the useful output power must always be strictly less than the total supplied power.

REASONING PATH
Your ACEpath teacher’s suggested approach
Reality Check on Conservation of Energy
  • Useful Output Power≤Total Input Power\text{Useful Output Power} \le \text{Total Input Power}

  • Whenever a device loses energy to the surroundings, verify that your calculated useful power is smaller than your source power before moving to the next step.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Calculate the thermal power absorbed by the water: Pabsorbed=η⋅Pelec=0.925×175.93 W≈162.74 WP_{\text{absorbed}} = \eta \cdot P_{\text{elec}} = 0.925 \times 175.93\text{ W} \approx 162.74\text{ W}.

  2. Substitute the corrected absorbed power into the calorimetry equation: ΔT=Pabsorbed(dmdt)⋅c=162.74 J/s(0.650 g/s)⋅(4.184 J/(g⋅∘C))\Delta T = \frac{P_{\text{absorbed}}}{\left(\frac{dm}{dt}\right) \cdot c} = \frac{162.74\text{ J/s}}{(0.650\text{ g/s}) \cdot (4.184\text{ J}/(\text{g}\cdot{^\circ}\text{C}))}.

  3. Evaluate the ratio: ΔT=162.742.7196 ∘C≈59.8 ∘C\Delta T = \frac{162.74}{2.7196}\text{ }^\circ\text{C} \approx 59.8\text{ }^\circ\text{C}.

Final answer

(a) Pelec=176 WP_{\text{elec}} = 176\text{ W}; (b) ΔT=59.8 ∘C\Delta T = 59.8\text{ }^\circ\text{C}

NEXT STEPS
Final Takeaways from Your Teacher
  • Always check whether you are solving for output from input (Pout=ηPinP_{\text{out}} = \eta P_{\text{in}}) or required input from desired output (Pin=Pout/ηP_{\text{in}} = P_{\text{out}} / \eta).

  • Perform a quick physical sanity check: if efficiency is less than 100%100\%, the absorbed thermal power can never exceed the electrical input.

OverviewACEpath Teacher's Diagnosis

03 A student inverts the formula for temperature rise as ΔT = ((dm/dt) × c) / P_absorbed, resulting in an incorrect value of 0.0167 °C.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    Pelec=V×I  ⟹  Pelec=48.2×3.65=175.93 WP_{\text{elec}} = V \times I \implies P_{\text{elec}} = 48.2 \times 3.65 = 175.93\text{ W}

  2. Step 2

    Pabsorbed=0.925×175.93=162.74 WP_{\text{absorbed}} = 0.925 \times 175.93 = 162.74\text{ W}

  3. Step 3

    ΔT=(dm/dt)×cPabsorbed\Delta T = \frac{(dm/dt) \times c}{P_{\text{absorbed}}}

    Correct

    ΔT=Pabsorbed(dmdt)⋅c\Delta T = \frac{P_{\text{absorbed}}}{\left(\frac{dm}{dt}\right) \cdot c}

    The steady-flow heat transfer rate is P=(dmdt)cΔTP = \left(\frac{dm}{dt}\right) c \Delta T. When isolating ΔT\Delta T, you must divide the power PP by the product (dmdt)c\left(\frac{dm}{dt}\right) c, not the other way around.

  4. Step 4

    ΔT=0.650×4.184162.74=0.0167 ∘C\Delta T = \frac{0.650 \times 4.184}{162.74} = 0.0167\text{ }^\circ\text{C}

    Correct

    ΔT=162.740.650×4.184≈59.8 ∘C\Delta T = \frac{162.74}{0.650 \times 4.184} \approx 59.8\text{ }^\circ\text{C}

    Your numerical evaluation accurately followed your inverted formula from Step 3, propagating the algebraic error into the final answer.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly used P=VIP = V I to determine the electrical input power.

You correctly applied the efficiency η\eta to find the thermal power entering the fluid.

You used consistent units for mass flow rate (g/s\text{g/s}) and specific heat capacity (J/(g⋅∘C)\text{J}/(\text{g}\cdot{^\circ}\text{C})).

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Algebraic Inversion

You accidentally placed the heat capacity rate in the numerator and the absorbed power in the denominator when rearranging the equation.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing the independent energy input rate (PP) with the heat capacity rate (m˙c\dot{m} c) during algebraic rearrangement, which can be caught early by checking that power divided by heat capacity rate yields temperature units.

REASONING PATH
Your ACEpath teacher’s suggested approach
Isolate the Desired Variable
  • If A=B⋅C⋅DA = B \cdot C \cdot D, then D=AB⋅CD = \frac{A}{B \cdot C}.

  • Divide both sides of P=(dmdt)cΔTP = \left(\frac{dm}{dt}\right) c \Delta T by (dmdt)c\left(\frac{dm}{dt}\right) c to isolate ΔT\Delta T.

Dimensional / Unit Check
  • PowerMass rate×Specific heat=J/s(g/s)(J/(g⋅∘C))=∘C\frac{\text{Power}}{\text{Mass rate} \times \text{Specific heat}} = \frac{\text{J/s}}{(\text{g/s})(\text{J}/(\text{g}\cdot{^\circ}\text{C}))} = {^\circ}\text{C}.

  • Check whether your isolated expression gives units of degrees Celsius before plugging in numbers.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Write the primary rate equation: Pabsorbed=(dmdt)cΔTP_{\text{absorbed}} = \left(\frac{dm}{dt}\right) c \Delta T.

  2. Isolate ΔT\Delta T by dividing both sides by (dmdt)c\left(\frac{dm}{dt}\right) c: ΔT=Pabsorbed(dmdt)c\Delta T = \frac{P_{\text{absorbed}}}{\left(\frac{dm}{dt}\right) c}.

  3. Substitute the numerical values: ΔT=162.74 J/s(0.650 g/s)×(4.184 J/(g⋅∘C))=162.742.7196 ∘C≈59.8 ∘C\Delta T = \frac{162.74\text{ J/s}}{(0.650\text{ g/s}) \times (4.184\text{ J}/(\text{g}\cdot{^\circ}\text{C}))} = \frac{162.74}{2.7196}\text{ }^\circ\text{C} \approx 59.8\text{ }^\circ\text{C}.

Final answer

(a) Pelec=176 WP_{\text{elec}} = 176\text{ W}; (b) ΔT=59.8 ∘C\Delta T = 59.8\text{ }^\circ\text{C}

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice isolating a target variable from multi-factor products before substituting numerical values.

  • Always perform a quick dimensional check to verify that your isolated formula yields the expected unit (e.g., ∘C^\circ\text{C} rather than 1/∘C1/{^\circ}\text{C}).

  • Sanity-check whether over 160 W160\text{ W} absorbed by a tiny trickle of water (0.65 g/s0.65\text{ g/s}) should produce a negligible 0.02∘C0.02^\circ\text{C} rise or a substantial heating effect.

Lock it in

Similar question

01

A continuous-flow heater operating at V=120 VV = 120\ \text{V} and I=5.00 AI = 5.00\ \text{A} transfers thermal energy into water with an efficiency of η=85.0%\eta = 85.0\%. If water flows at a mass rate of dmdt=4.00 g/s\frac{dm}{dt} = 4.00\ \text{g/s} with specific heat capacity c=4.184 J/(g⋅∘C)c = 4.184\ \text{J}/(\text{g}\cdot{^\circ}\text{C}), calculate the steady-state temperature rise ΔT\Delta T.

Answer

ΔT=30.5 ∘C\Delta T = 30.5\ {^\circ}\text{C}. Key steps: Pelec=120×5.00=600 WP_{\text{elec}} = 120 \times 5.00 = 600\text{ W}; Ptherm=0.850×600=510 WP_{\text{therm}} = 0.850 \times 600 = 510\text{ W}; ΔT=510 W(4.00 g/s)(4.184 J/(g⋅∘C))≈30.5 ∘C\Delta T = \frac{510\text{ W}}{(4.00\text{ g/s})(4.184\text{ J}/(\text{g}\cdot{^\circ}\text{C}))} \approx 30.5\ {^\circ}\text{C}.

02

Water (c=4.184 J/(g⋅∘C)c = 4.184\ \text{J}/(\text{g}\cdot{^\circ}\text{C})) flows through an electric heating chamber at 1.50 g/s1.50\ \text{g/s} and undergoes a temperature rise of ΔT=45.0 ∘C\Delta T = 45.0\ {^\circ}\text{C}. If the heating coil operates at 24.0 V24.0\ \text{V} and draws 14.0 A14.0\ \text{A}, what is the thermal efficiency η\eta of the heater?

Answer

η=84.1%\eta = 84.1\%. Key steps: Pelec=24.0×14.0=336 WP_{\text{elec}} = 24.0 \times 14.0 = 336\text{ W}; Ptherm=(dmdt)cΔT=(1.50)(4.184)(45.0)=282.42 WP_{\text{therm}} = \left(\frac{dm}{dt}\right)c\Delta T = (1.50)(4.184)(45.0) = 282.42\text{ W}; η=282.42336≈0.841=84.1%\eta = \frac{282.42}{336} \approx 0.841 = 84.1\%.

03

An electric immersion heater of resistance R=12.0 ΩR = 12.0\ \Omega is connected across a 120 V120\ \text{V} line to heat an oil stream (coil=2.10 J/(g⋅∘C)c_{\text{oil}} = 2.10\ \text{J}/(\text{g}\cdot{^\circ}\text{C})). The unit has an efficiency of η=88.0%\eta = 88.0\%. To maintain a steady temperature increase of exactly 25.0 ∘C25.0\ {^\circ}\text{C}, what mass flow rate dmdt\frac{dm}{dt} in g/s\text{g/s} must be maintained?

Answer

dmdt=20.1 g/s\frac{dm}{dt} = 20.1\ \text{g/s}. Key steps: Pelec=V2R=120212.0=1200 WP_{\text{elec}} = \frac{V^2}{R} = \frac{120^2}{12.0} = 1200\text{ W}; Ptherm=0.880×1200=1056 WP_{\text{therm}} = 0.880 \times 1200 = 1056\text{ W}; dmdt=PthermcΔT=1056(2.10)(25.0)≈20.1 g/s\frac{dm}{dt} = \frac{P_{\text{therm}}}{c\Delta T} = \frac{1056}{(2.10)(25.0)} \approx 20.1\ \text{g/s}.

Loading workspace…