Resources
A straight horizontal metal rod of length and mass rests on a rough horizontal insulating surface with a coefficient of static friction . A uniform magnetic field of magnitude points vertically upward perpendicular to the surface. A variable direct current is established along the length of the rod. Taking , determine the critical threshold current required to initiate impending slip of the rod along the surface.
Answer and steps
Final answer
Steps
Analyze the Forces in the Vertical Direction
To determine the critical threshold current that initiates slipping, we analyze the forces acting on the rod along the vertical and horizontal directions at impending motion.
The rod rests on a horizontal surface, subject to:
- The downward gravitational force:
- The upward normal contact force from the surface:
Since the magnetic field is vertically upward and the current flows horizontally, the magnetic force acts entirely in the horizontal plane. Consequently, there is no vertical component of the magnetic force:
Substitute the given values:
Determine the Maximum Static Friction Force
The surface resists horizontal motion through static friction. The maximum static friction force that must be overcome to start motion is:
Substitute the numerical values:
Calculate the Horizontal Magnetic Force
The magnetic force acting on a straight, current-carrying conductor in a uniform magnetic field is given by:
Because the rod lies horizontally and the magnetic field points vertically upward, the angle between the current vector and the magnetic field vector is ():
By the right-hand rule, this force acts parallel to the horizontal surface, driving the rod sideways against friction.
Apply the Condition for Impending Slip
The rod begins to slip when the magnetic driving force reaches the maximum static friction threshold:
Solve for :
Substitute the values into the equation:
(Note: Ensure that the angle between the magnetic field and current is identified correctly. If the magnetic field had any horizontal component, the normal force would be altered by a vertical magnetic force component.)
Typical errors
01 The student forgets to multiply mass by gravitational acceleration g when calculating the normal force, confusing mass directly with weight.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
You set up the impending slip balance correctly as , but maximum static friction is . Because the rod rests on a horizontal plane with no vertical magnetic force, the normal force is , not simply .
- Step 2Correct
You rearranged the variables accurately based on your previous equation, but the gravitational acceleration is missing from the numerator.
- Step 3Correct
Your numerical arithmetic is correct for the values you entered, but omitting makes your final threshold current too small by a factor of .
WHAT YOU DID WELL
Compliments from Your TeacherYou recognized that impending motion occurs when the magnetic force equals the maximum static friction force.
You correctly used for a current perpendicular to a uniform magnetic field.
You isolated the target variable with correct algebraic manipulation.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou treated mass directly as the normal force in the friction relation , forgetting that weight and normal force have units of force (Newtons) and require multiplying mass by gravitational acceleration ().
REASONING PATH
Your ACEpath teacher’s suggested approach- Check Normal Force vs. Mass
Friction depends on contact force (), never directly on mass ().
Always write explicitly before substituting into .
- Dimensional Consistency Check
The product has units of , whereas friction is a force with units of .
Check that every force term has units of Newtons by ensuring mass is multiplied by acceleration.
CORRECTED PATH
ACEpath Teacher's DemonstrationBalance vertical forces to find the normal force: .
Substitute into the impending slip condition: .
Solve for : .
02 The student inverts the relationship between magnetic force and friction, placing the magnetic field and length terms in the numerator rather than the denominator.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
When isolating from , you must divide both sides by the coefficients of (which are and ), leaving in the numerator.
- Step 3Correct
Your numerical computation was executed accurately according to your inverted formula, but the result is the reciprocal of the true critical current.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly identified that the threshold for impending slip occurs when the magnetic force equals the maximum static friction force.
You used the correct expressions and .
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou inverted the fraction when isolating the target variable , placing the coefficient factors in the numerator and the independent product in the denominator.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing division and multiplication during symbolic isolation, specifically dividing the isolated side by the target variable's coefficients rather than placing the target's coefficients in the denominator.
REASONING PATH
Your ACEpath teacher’s suggested approach- Isolating a Variable from a Product
For an equation of the form , dividing both sides by yields .
Always circle the variable you want to isolate and divide the opposite side by all factors multiplying that variable.
- Dimensional and Limiting Checks
If friction or mass increases, it must require more current to overcome friction, meaning and must be in the numerator.
Perform a physical trend check: verify that increasing the resisting force increases the required driving current.
CORRECTED PATH
ACEpath Teacher's DemonstrationDivide both sides of by : .
Substitute the known values: .
Evaluate the numerator and denominator: .
03 The student omits the coefficient of static friction, assuming the magnetic force only needs to overcome the full gravitational weight.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
The magnetic force acts horizontally parallel to the surface, while gravity acts vertically downward. To initiate horizontal slip, the magnetic driving force must overcome the threshold of maximum static friction, , not the full weight of the rod.
- Step 2Correct
This rearrangement follows correctly from your initial equation, but it carries forward the missing coefficient of static friction .
- Step 3Correct
Your arithmetic evaluation was carried out accurately based on your formula, but the resulting current is higher than the actual threshold because was omitted.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly identified the magnetic force formula for a current perpendicular to a magnetic field.
You isolated the target variable algebraically with clear, systematic steps.
You performed the numerical division accurately.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou set the horizontal driving force equal to the vertical gravitational force rather than the maximum static friction force .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing the normal contact force or weight with the frictional resistance along the surface plane.
REASONING PATH
Your ACEpath teacher’s suggested approach- Resolve Forces by Direction
Forces acting along perpendicular axes do not directly balance each other without a physical coupling mechanism.
Draw a free-body diagram separating vertical equilibrium () from horizontal motion threshold ().
- Apply Static Friction Law
The maximum force static friction can supply before slipping begins is .
Multiply the normal force by whenever finding the threshold force required to initiate sliding.
CORRECTED PATH
ACEpath Teacher's DemonstrationState horizontal equilibrium at the slipping threshold: .
Substitute the formulas for magnetic force and maximum static friction: .
Solve for the critical current: .
Substitute the given numerical values: .
Lock it in
What is the relationship between the maximum static friction force and the mass of an object resting on a horizontal plane?
. Friction depends on the normal force , not directly on mass .
Similar question
A horizontal copper wire of length and mass rests on a horizontal table where . A uniform magnetic field points vertically upward. Taking , find the critical current needed to start the wire sliding.
Answer
At impending slip, . Solving for : .
A conductive rod of length and mass carries a current directed horizontally along the -axis on a horizontal surface with . A horizontal magnetic field points along the -axis. Taking , determine the normal force exerted by the surface on the rod and state whether the rod slips.
Answer
By the right-hand rule, points in the (upward) direction: . Gravitational force is . Vertical equilibrium gives . Because there is no horizontal applied force parallel to the surface, the horizontal friction required is zero, so the rod does not slip horizontally.
A conductive rod of length and mass rests on a rough plane inclined at to the horizontal. A uniform magnetic field points vertically upward. A current is directed along the rod such that the magnetic force acts horizontally into the incline, pushing the rod up the plane. If the coefficient of static friction is and , find the minimum current required to prevent the rod from sliding down the incline.
Answer
Resolve forces parallel and perpendicular to the incline. Magnetic force is horizontal: . Normal force is . Impending downward slip means friction acts up the incline: . Substituting : . Thus . Then .