Resources

A roller-coaster cart with a mass of m=450 kgm = 450\text{ kg} is released from rest at the top of a hill at an elevation of h=32.0 mh = 32.0\text{ m} above ground level. Taking the ground as the reference zero for gravitational potential energy and assuming negligible friction and air resistance, calculate: (a) the initial gravitational potential energy UgU_g of the cart at the top of the hill, and (b) the kinetic energy KK and speed vv of the cart when it reaches a lower point at a height of y=12.0 my = 12.0\text{ m} above the ground. Use g=9.80 m/s2g = 9.80\text{ m/s}^2.

Answer and steps

Final answer

(a) Ug=1.41×105 JU_g = 1.41 \times 10^5\text{ J}; (b) K=8.82×104 JK = 8.82 \times 10^4\text{ J}, v=19.8 m/sv = 19.8\text{ m/s}.

Steps

01

Kinetic Energy (KK)

Part (a): Initial Gravitational Potential Energy

Gravitational potential energy UgU_g near Earth's surface relative to a chosen reference level (y=0 my = 0\text{ m} at the ground) is given by: Ug=mghU_g = mgh Given:

  • Mass of the cart, m=450 kgm = 450\text{ kg}
  • Acceleration due to gravity, g=9.80 m/s2g = 9.80\text{ m/s}^2
  • Initial height, h=32.0 mh = 32.0\text{ m} Substitute the known values into the equation: Ug=(450 kg)⋅(9.80 m/s2)⋅(32.0 m)=141,120 JU_g = (450\text{ kg}) \cdot (9.80\text{ m/s}^2) \cdot (32.0\text{ m}) = 141,120\text{ J} Expressed to three significant figures in scientific notation: Ug=1.41×105 JU_g = 1.41 \times 10^5\text{ J}

Part (b): Kinetic Energy and Speed at y=12.0 my = 12.0\text{ m}

Because friction and air resistance are negligible, the total mechanical energy EE of the system is conserved:

Einitial=EfinalE_{\text{initial}} = E_{\text{final}}

At the release point, the cart starts from rest, so its initial kinetic energy is zero (Ki=0K_i = 0):

Einitial=Ki+Ug=0+141,120 J=141,120 JE_{\text{initial}} = K_i + U_g = 0 + 141,120\text{ J} = 141,120\text{ J}

At height y=12.0 my = 12.0\text{ m}, the final mechanical energy consists of both kinetic energy KK and gravitational potential energy UfU_f:

Uf=mgy=(450 kg)⋅(9.80 m/s2)⋅(12.0 m)=52,920 JU_f = mgy = (450\text{ kg}) \cdot (9.80\text{ m/s}^2) \cdot (12.0\text{ m}) = 52,920\text{ J}

By the law of conservation of energy:

K=Einitial−UfK = E_{\text{initial}} - U_f

K=141,120 J−52,920 J=88,200 JK = 141,120\text{ J} - 52,920\text{ J} = 88,200\text{ J}

Expressed to three significant figures:

K=8.82×104 JK = 8.82 \times 10^4\text{ J}

(Alternatively, the gain in kinetic energy directly equals the loss in potential energy: K=mg(h−y)=(450 kg)⋅(9.80 m/s2)⋅(32.0 m−12.0 m)=88,200 JK = mg(h - y) = (450\text{ kg}) \cdot (9.80\text{ m/s}^2) \cdot (32.0\text{ m} - 12.0\text{ m}) = 88,200\text{ J}.)

02

Speed (vv)

The kinetic energy is related to the cart's speed by:

K=12mv2K = \frac{1}{2}mv^2

Rearranging for vv:

v=2Kmv = \sqrt{\frac{2K}{m}}

Substitute the values:

v=2⋅88,200 J450 kg=392 m2/s2≈19.8 m/sv = \sqrt{\frac{2 \cdot 88,200\text{ J}}{450\text{ kg}}} = \sqrt{392\text{ m}^2/\text{s}^2} \approx 19.8\text{ m/s}

Common Pitfall: When calculating kinetic energy from energy loss, be careful to use the vertical drop Δh=h−y=20.0 m\Delta h = h - y = 20.0\text{ m} rather than the remaining height y=12.0 my = 12.0\text{ m}. Using the remaining height gives the potential energy remaining, not the energy converted into motion.

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student calculates kinetic energy using the current height of 12.0 m instead of the height lost or the change in potential energy.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    Ug=m⋅g⋅h=450⋅9.80⋅32.0=141,120 JU_g = m \cdot g \cdot h = 450 \cdot 9.80 \cdot 32.0 = 141{,}120\text{ J}

  2. Step 2

    K=m⋅g⋅y=450⋅9.80⋅12.0=52,920 JK = m \cdot g \cdot y = 450 \cdot 9.80 \cdot 12.0 = 52{,}920\text{ J}

    Correct

    K=mg(h−y)=141,120 J−52,920 J=88,200 J=8.82×104 JK = mg(h - y) = 141{,}120\text{ J} - 52{,}920\text{ J} = 88{,}200\text{ J} = 8.82 \times 10^4\text{ J}

    The formula mgymgy gives the gravitational potential energy still remaining at y=12.0 my = 12.0\text{ m}, not the kinetic energy. By conservation of energy, kinetic energy gained equals potential energy lost: K=mg(h−y)K = mg(h - y).

  3. Step 3

    v=2Km=2⋅52,920450=235.2≈15.3 m/sv = \sqrt{\frac{2K}{m}} = \sqrt{\frac{2 \cdot 52{,}920}{450}} = \sqrt{235.2} \approx 15.3\text{ m/s}

    Correct

    v=2Km=2⋅88,200450=392≈19.8 m/sv = \sqrt{\frac{2K}{m}} = \sqrt{\frac{2 \cdot 88{,}200}{450}} = \sqrt{392} \approx 19.8\text{ m/s}

    Your formula rearrangement and substitution for speed were algebraically sound, but your numerical answer was affected by the incorrect value of kinetic energy from Step 2.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly calculated the initial gravitational potential energy at the summit using Ug=mghU_g = mgh.

You correctly set up the formula relating speed to kinetic energy, v=2K/mv = \sqrt{2K/m}.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Height remaining vs. height lost confusion

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You confused the remaining gravitational potential energy at height yy with the kinetic energy gained, using the instantaneous height y=12.0 my = 12.0\text{ m} instead of the vertical displacement fallen Δh=h−y=20.0 m\Delta h = h - y = 20.0\text{ m}.

REASONING PATH
Your ACEpath teacher’s suggested approach
Identify Energy Transfer
  • In an isolated system starting from rest, ΔK=−ΔUg=mgΔhlost\Delta K = -\Delta U_g = mg\Delta h_{\text{lost}}.

  • Always compute kinetic energy from the vertical distance fallen (hinitial−hfinalh_{\text{initial}} - h_{\text{final}}), not from the height remaining above the ground.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Calculate the vertical drop: Δh=32.0 m−12.0 m=20.0 m\Delta h = 32.0\text{ m} - 12.0\text{ m} = 20.0\text{ m}.

  2. Compute kinetic energy from the potential energy lost: K=mgΔh=(450 kg)(9.80 m/s2)(20.0 m)=88,200 J=8.82×104 JK = mg\Delta h = (450\text{ kg})(9.80\text{ m/s}^2)(20.0\text{ m}) = 88{,}200\text{ J} = 8.82 \times 10^4\text{ J}.

  3. Substitute the corrected kinetic energy into the speed formula: v=2⋅88,200 J450 kg=392 m2/s2≈19.8 m/sv = \sqrt{\frac{2 \cdot 88{,}200\text{ J}}{450\text{ kg}}} = \sqrt{392\text{ m}^2/\text{s}^2} \approx 19.8\text{ m/s}.

Final answer

(a) Ug=1.41×105 JU_g = 1.41 \times 10^5\text{ J}; (b) K=8.82×104 JK = 8.82 \times 10^4\text{ J}, v=19.8 m/sv = 19.8\text{ m/s}

NEXT STEPS
Final Takeaways from Your Teacher
  • When using energy conservation, write out Ei=EfE_i = E_f explicitly (Ki+Ui=Kf+UfK_i + U_i = K_f + U_f) before plugging in numbers so you clearly see that Kf=Ui−UfK_f = U_i - U_f.

  • Double-check whether each height variable represents altitude above reference (yy) or distance dropped (Δy\Delta y).

OverviewACEpath Teacher's Diagnosis

02 The student omits the factor of 1/2 when solving for speed from kinetic energy, using v = √(K / m).

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    Ug=m∗g∗h=450∗9.80∗32.0=141,120 JU_g = m * g * h = 450 * 9.80 * 32.0 = 141,120\text{ J}

  2. Step 2

    Δh=32.0−12.0=20.0 m  ⟹  K=m∗g∗Δh=450∗9.80∗20.0=88,200 J\Delta h = 32.0 - 12.0 = 20.0\text{ m} \implies K = m * g * \Delta h = 450 * 9.80 * 20.0 = 88,200\text{ J}

  3. Step 3

    v=Km=88,200450=196=14 m/sv = \sqrt{\frac{K}{m}} = \sqrt{\frac{88,200}{450}} = \sqrt{196} = 14\text{ m/s}

    Correct

    v=2Km=2(88,200 J)450 kg=392 m2/s2≈19.8 m/sv = \sqrt{\frac{2K}{m}} = \sqrt{\frac{2(88,200\text{ J})}{450\text{ kg}}} = \sqrt{392\text{ m}^2/\text{s}^2} \approx 19.8\text{ m/s}

    When rearranging K=12mv2K = \frac{1}{2}mv^2 for speed, multiplying both sides by 22 gives v2=2Kmv^2 = \frac{2K}{m}, which leads to v=2Kmv = \sqrt{\frac{2K}{m}}. Omitting the 22 under the radical resulted in an underestimated speed of 14 m/s14\text{ m/s} instead of 19.8 m/s19.8\text{ m/s}.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly calculated the initial gravitational potential energy using Ug=mghU_g = mgh.

You correctly applied energy conservation by relating the vertical drop Δh\Delta h to the gain in kinetic energy.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Omitted coefficient in formula rearrangement

You wrote v=Kmv = \sqrt{\frac{K}{m}} instead of v=2Kmv = \sqrt{\frac{2K}{m}}, forgetting to multiply by 22 when isolating v2v^2.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Incomplete algebraic rearrangement of K=12mv2K = \frac{1}{2}mv^2, where the denominator 22 in the 12\frac{1}{2} factor was dropped rather than cleared by multiplying both sides by 22.

REASONING PATH
Your ACEpath teacher’s suggested approach
Isolate squared variable with fractions
  • To solve 12mv2=K\frac{1}{2}mv^2 = K, first multiply both sides by 22 to clear the fraction: mv2=2Kmv^2 = 2K, then divide by mm: v2=2Kmv^2 = \frac{2K}{m}.

  • Always write out the intermediate step v2=2Kmv^2 = \frac{2K}{m} before taking the square root.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Start from the kinetic energy definition: K=12mv2K = \frac{1}{2}mv^2.

  2. Multiply both sides by 22 and divide by mm: v=2Kmv = \sqrt{\frac{2K}{m}}.

  3. Substitute the known values: v=2×88,200 J450 kg=392 m2/s2≈19.8 m/sv = \sqrt{\frac{2 \times 88,200\text{ J}}{450\text{ kg}}} = \sqrt{392\text{ m}^2/\text{s}^2} \approx 19.8\text{ m/s}.

Final answer

(a) Ug=1.41×105 JU_g = 1.41 \times 10^5\text{ J}; (b) K=8.82×104 JK = 8.82 \times 10^4\text{ J}, v=19.8 m/sv = 19.8\text{ m/s}

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice rearranging formulas that include 12\frac{1}{2}, such as kinetic energy K=12mv2K = \frac{1}{2}mv^2 and elastic potential energy Us=12kx2U_s = \frac{1}{2}kx^2.

  • Perform a quick dimensional or ratio check: verify that v2v^2 has the correct factor of 22 relative to Km\frac{K}{m}.

OverviewACEpath Teacher's Diagnosis

03 The student equates the kinetic energy at 12.0 m directly to the total initial potential energy, ignoring the remaining potential energy.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    Ug=450⋅9.80⋅32.0=141,120 JU_g = 450 \cdot 9.80 \cdot 32.0 = 141,120\text{ J}

  2. Step 2

    K=Ug=141,120 JK = U_g = 141,120\text{ J}

    Correct

    K=Ei−Uf=141,120 J−(450 kg)(9.80 m/s2)(12.0 m)=88,200 JK = E_i - U_f = 141,120\text{ J} - (450\text{ kg})(9.80\text{ m/s}^2)(12.0\text{ m}) = 88,200\text{ J}

    At an elevation of y=12.0 my = 12.0\text{ m}, the cart still retains gravitational potential energy (Uf=mgyU_f = mgy). The kinetic energy gained equals the loss in potential energy, ΔU=mg(h−y)\Delta U = mg(h - y), rather than the full initial potential energy.

  3. Step 3

    v=2⋅Km  ⟹  v=2⋅141,120450=627.2≈25.0 m/sv = \sqrt{\frac{2 \cdot K}{m}} \implies v = \sqrt{\frac{2 \cdot 141,120}{450}} = \sqrt{627.2} \approx 25.0\text{ m/s}

    Correct

    v=2⋅88,200 J450 kg=392 m2/s2≈19.8 m/sv = \sqrt{\frac{2 \cdot 88,200\text{ J}}{450\text{ kg}}} = \sqrt{392\text{ m}^2/\text{s}^2} \approx 19.8\text{ m/s}

    Your algebraic rearrangement v=2Kmv = \sqrt{\frac{2K}{m}} is completely correct, but substituting the incorrect value of KK led to an overestimated speed.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly computed the initial gravitational potential energy using Ug=mghU_g = mgh.

You correctly applied the formula relating kinetic energy to speed, v=2Kmv = \sqrt{\frac{2K}{m}}.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Omission of Remaining Potential Energy at Intermediate Height

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You equated kinetic energy directly to the total initial potential energy (K=Ug,iK = U_{g,i}), which only holds true at the reference zero level (y=0 my = 0\text{ m}). At any height above the ground, total mechanical energy is split between kinetic and potential energy: K=Etotal−UremainingK = E_{\text{total}} - U_{\text{remaining}}.

REASONING PATH
Your ACEpath teacher’s suggested approach
Energy Conservation at Non-Zero Heights
  • Etotal=K+Ug=constantE_{\text{total}} = K + U_g = \text{constant}

  • Check whether the cart has reached the ground (y=0 my = 0\text{ m}) or is at an intermediate height. If it is still elevated, subtract the remaining potential energy Uf=mgyU_f = mgy from total energy to find kinetic energy: K=mg(h−y)K = mg(h - y).

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Calculate the potential energy remaining at y=12.0 my = 12.0\text{ m}: Uf=(450 kg)(9.80 m/s2)(12.0 m)=52,920 JU_f = (450\text{ kg})(9.80\text{ m/s}^2)(12.0\text{ m}) = 52,920\text{ J}.

  2. Apply conservation of mechanical energy: K=Einitial−Uf=141,120 J−52,920 J=88,200 JK = E_{\text{initial}} - U_f = 141,120\text{ J} - 52,920\text{ J} = 88,200\text{ J} (or 8.82×104 J8.82 \times 10^4\text{ J}).

  3. Solve for the speed using the corrected kinetic energy: v=2⋅88,200 J450 kg=392 m2/s2≈19.8 m/sv = \sqrt{\frac{2 \cdot 88,200\text{ J}}{450\text{ kg}}} = \sqrt{392\text{ m}^2/\text{s}^2} \approx 19.8\text{ m/s}.

Final answer

(a) Ug=1.41×105 JU_g = 1.41 \times 10^5\text{ J}; (b) K=8.82×104 JK = 8.82 \times 10^4\text{ J}, v=19.8 m/sv = 19.8\text{ m/s}

NEXT STEPS
Final Takeaways from Your Teacher
  • Always write out the full conservation equation Ki+Ui=Kf+UfK_i + U_i = K_f + U_f before substituting zeros or numbers.

  • Sketch the track with the elevation levels marked to visually track the height drop Δh=hi−hf\Delta h = h_i - h_f that actually converts into kinetic energy.

Lock it in

Similar question

01

A 2.0 kg2.0\text{ kg} textbook slides off a shelf at a height of 2.5 m2.5\text{ m} above the floor. What is its kinetic energy when it passes a desk at a height of 0.8 m0.8\text{ m} above the floor? Take g=9.80 m/s2g = 9.80\text{ m/s}^2.

Answer

K=mg(hi−hf)=(2.0 kg)(9.80 m/s2)(2.5 m−0.8 m)=(2.0)(9.80)(1.7)≈33.3 JK = mg(h_i - h_f) = (2.0\text{ kg})(9.80\text{ m/s}^2)(2.5\text{ m} - 0.8\text{ m}) = (2.0)(9.80)(1.7) \approx 33.3\text{ J}.

02

A 60.0 kg60.0\text{ kg} skier starts from rest at the top of a hill of height 45.0 m45.0\text{ m}. Neglecting friction and air resistance, find the skier's speed when they reach an intermediate plateau at a height of 25.0 m25.0\text{ m}. Use g=9.80 m/s2g = 9.80\text{ m/s}^2.

Answer

Vertical drop Δh=45.0 m−25.0 m=20.0 m\Delta h = 45.0\text{ m} - 25.0\text{ m} = 20.0\text{ m}. By conservation of energy, v=2gΔh=2(9.80)(20.0)=392≈19.8 m/sv = \sqrt{2g\Delta h} = \sqrt{2(9.80)(20.0)} = \sqrt{392} \approx 19.8\text{ m/s}.

03

A roller coaster cart of mass mm passes over a crest of height h1=30.0 mh_1 = 30.0\text{ m} with an initial speed of v1=4.0 m/sv_1 = 4.0\text{ m/s}. Find its speed at a lower point of height h2=10.0 mh_2 = 10.0\text{ m}. Use g=9.80 m/s2g = 9.80\text{ m/s}^2.

Answer

By conservation of mechanical energy, 12mv12+mgh1=12mv22+mgh2\frac{1}{2}mv_1^2 + mgh_1 = \frac{1}{2}mv_2^2 + mgh_2, so v2=v12+2g(h1−h2)=4.02+2(9.80)(20.0)=16+392=408≈20.2 m/sv_2 = \sqrt{v_1^2 + 2g(h_1 - h_2)} = \sqrt{4.0^2 + 2(9.80)(20.0)} = \sqrt{16 + 392} = \sqrt{408} \approx 20.2\text{ m/s}.

Loading workspace…