Resources
An experimenter warms a sealed sample of an unknown noble gas (behaving as an ideal monatomic gas with ) inside a fixed-volume container. The system absorbs of heat from a surrounding water bath, causing the temperature of the gas to rise from to a final recorded temperature of . Assuming zero mechanical work is done and heat losses are negligible, reverse-engineer the initial state to determine the number of moles of the gas present in the container.
Answer and steps
Final answer
.
Steps
Apply the First Law of Thermodynamics
The First Law of Thermodynamics connects the heat transferred to a system (), the work done by the system (), and the change in its internal energy ():
Because the gas is enclosed in a rigid, fixed-volume container, no boundary moves, meaning zero mechanical work is performed on or by the gas:
Therefore, all the heat absorbed directly increases the internal energy of the gas:
Relate Internal Energy Change to Temperature Change
For an ideal gas, the internal energy is directly proportional to its absolute temperature. The change in internal energy for moles of a gas undergoing a temperature change is given by:
where:
- is the molar heat capacity at constant volume for a monatomic ideal gas,
- is the universal gas constant.
Calculate the Temperature Change
Find the change in temperature from the given initial and final values:
Solve for the Number of Moles ()
Equating the two expressions for :
Rearranging the formula to solve for :
Substitute the numerical values:
Common Pitfall: Be careful to use the constant-volume molar heat capacity rather than the constant-pressure heat capacity , since the rigid walls prevent expansion work.
Typical errors
01 The student confuses the constant-volume molar heat capacity C_V with the constant-pressure molar heat capacity C_P = (5/2)R, resulting in an underestimated number of moles.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
Because the gas is sealed in a fixed-volume container, no expansion work is done (), so the absorbed heat relates to temperature change via the constant-volume heat capacity , not .
- Step 2
- Step 3Correct
Your algebraic isolation and arithmetic were carried out correctly, but the result was thrown off by the earlier choice of instead of .
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly calculated the temperature difference .
You set up a direct proportion between heat absorbed and temperature change using the ideal gas constant .
You solved for algebraically with accurate arithmetic.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou substituted into the heat equation instead of the given .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou associated heating an ideal gas with without checking the physical boundary condition: a rigid, fixed-volume container prevents expansion work, so all heat goes into internal energy ().
REASONING PATH
Your ACEpath teacher’s suggested approach- Check container boundary mobility
If the container is rigid or fixed-volume (), use . If the container has a movable piston at constant pressure, use .
Look for keywords like 'fixed-volume', 'rigid', or 'sealed container' to immediately select .
- Connect First Law to heat capacity
. When , .
Write down the First Law of Thermodynamics before selecting a heat formula to verify whether boundary work occurs.
CORRECTED PATH
ACEpath Teacher's DemonstrationSet up the heat transfer equation for constant volume: .
Substitute the known values: .
Simplify the denominator: .
Compute the number of moles: .
02 The student uses the final absolute temperature instead of the temperature change in the internal energy relation.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
You substituted the absolute final temperature into the heat equation instead of the temperature change . Because the heat added equals the change in internal energy ( when ), it must be proportional to .
- Step 2Correct
Your algebraic rearrangement and arithmetic were carried out correctly, but the numerical result was affected by using instead of .
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly identified the molar heat capacity for an ideal monatomic gas as .
You used the correct universal gas constant .
You isolated and solved the linear equation accurately based on your substituted values.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou treated heat transfer as a measure of the total internal energy at temperature rather than the change in internal energy corresponding to the temperature change .
REASONING PATH
Your ACEpath teacher’s suggested approach- Heat vs. Internal Energy
Heat is energy in transit between systems; it changes a system's internal energy by , whereas total internal energy is .
Always write whenever a problem specifies an initial and a final temperature for heat absorption or release.
CORRECTED PATH
ACEpath Teacher's DemonstrationCalculate the change in temperature: .
Apply the First Law for an isochoric process (): .
Substitute the known values: .
Solve for : .
03 The student omits the factor of 3/2 from the molar heat capacity, incorrectly setting C_V = R.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
For an isochoric process with a monatomic ideal gas, the heat absorbed is where , rather than simply .
- Step 3Correct
Your algebraic rearrangement was carried out correctly, but the result is inaccurate because it propagated the missing factor.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly calculated the temperature change .
You recognized that heat transfer is directly proportional to , the gas constant, and .
You correctly solved for from your setup equation.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou used as the molar heat capacity instead of for a monatomic ideal gas at constant volume. For an ideal gas, each translational degree of freedom contributes to the molar heat capacity, giving .
REASONING PATH
Your ACEpath teacher’s suggested approach- Identify Process Type and Heat Capacity
In a rigid container, volume is constant (), so .
Always verify whether the gas is monatomic () or diatomic () before substituting into .
- Connect Internal Energy to Heat Capacity
The universal gas constant alone is not a heat capacity; includes a numerical factor based on the degrees of freedom.
Write with explicitly before replacing with numbers.
CORRECTED PATH
ACEpath Teacher's DemonstrationState the constant-volume heat relation: .
Substitute the known quantities: .
Simplify the coefficient: .
Solve for : .
Lock it in
When heat is added to an ideal gas in a rigid, fixed-volume container, which molar heat capacity relates heat to temperature change ()?
Use . Since volume is constant, work , meaning all heat directly changes internal energy: .
Similar question
A sample of of a monatomic ideal gas () is held inside a rigid steel tank. If the gas absorbs of heat, find the resulting temperature rise . (Use )
Answer
. For a rigid tank, , so . Thus, .
A rigid cylinder contains of helium gas (). It is heated such that its temperature increases from to . Calculate: (a) the work done by the gas , and (b) the heat input .
Answer
(a) because the boundary does not move (rigid container). (b) . By the First Law, .
Compare two identical samples of a monatomic ideal gas (, ), each absorbing of heat. Sample A is in a rigid, fixed-volume vessel. Sample B is in a cylinder fitted with a frictionless piston at constant atmospheric pressure. Which sample experiences a larger temperature increase, and what is the ratio ?
Answer
Sample A experiences the larger increase, with . For Sample A, . For Sample B, . The ratio is .