Resources
A block of mass is placed against a vertical rough wall. An ideal horizontal spring with force constant is compressed against the block, pressing it perpendicular to the wall. The coefficient of static friction between the block and the wall is . Taking : (a) Classify each force acting on the block into its fundamental category (gravitational, normal, frictional, tension, or elastic) and state its directional axis. (b) Determine the minimum spring compression required to prevent the block from slipping down the wall.
Answer and steps
Final answer
(a) Gravitational force (downward along vertical -axis); Static frictional force (upward along vertical -axis); Elastic restoring force (horizontal toward wall along -axis); Normal force (horizontal away from wall along -axis). (b) (or ).
Steps
Apply Equilibrium Conditions
Part (a): Classifying the Forces on the Block
To identify all forces acting on the block, separate them into non-contact (field) forces and contact forces:
- Gravitational Force ():
- Category: Gravitational force (field force exerted by Earth).
- Direction: Directed vertically downward along the negative -axis ().
- Magnitude: .
- Static Frictional Force ():
- Category: Frictional force (parallel contact force exerted by the rough vertical wall).
- Direction: Directed vertically upward along the positive -axis () to oppose the downward tendency of motion due to gravity.
- Elastic Restoring Force ():
- Category: Elastic force (contact force exerted by the compressed spring according to Hooke's law).
- Direction: Directed horizontally toward the wall along the positive -axis ().
- Normal Force ():
- Category: Normal force (perpendicular contact force exerted by the rigid wall).
- Direction: Directed horizontally away from the wall along the negative -axis ().
Part (b): Finding the Minimum Spring Compression
For the block to remain stationary against the wall, it must satisfy Newton's first law in both coordinate directions ():
- Horizontal axis ():
- Vertical axis ():
Relate Friction to the Normal Force
Static friction can adjust up to a maximum threshold without the object slipping:
Substitute the expressions for and :
Solving for the spring compression :
Common Pitfall: Static friction does not always equal ; it matches the opposing force () and only reaches at the critical point of impending motion.
Calculate the Minimum Compression
Setting to its threshold value:
Substitute the given numerical values:
Typical errors
01 The student confuses the normal force with the gravitational force when calculating maximum static friction, setting fs,max = μs mg instead of μs N.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
Gravity: gravitational force, downward along y-axis ⟹ Normal force: normal force, horizontal away from wall along x-axis ⟹ Spring force: elastic force, horizontal toward wall along x-axis ⟹ Friction: frictional force, upward along y-axis
- Step 2
- Step 3Correct
By definition, the maximum static friction depends on the normal force pressing the surfaces together (), not the object's weight. Here, the wall is vertical, so the normal force is horizontal and supplied by the compressed spring ().
- Step 4Correct
Because was set to and equated to rather than using the slip condition with and , the resulting numerical compression is incorrect.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly classified all four forces into their fundamental categories and specified their coordinate directions.
You correctly balanced the vertical forces to determine that static friction must equal the weight of the block.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou substituted the block's weight into the friction formula instead of using the contact normal force .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou treated maximum friction as as a routine formula rather than deriving from the perpendicular contact interface. Because the contact wall is vertical, the perpendicular force is the horizontal spring force (), while gravity acts parallel to the wall.
REASONING PATH
Your ACEpath teacher’s suggested approach- Identify the Contact Surface Orientation
The normal force is always perpendicular to the contact surface, while friction is parallel to the surface.
Draw the interface. Since the wall is vertical, identify that must lie along the horizontal axis, meaning determines .
- Apply Coulomb's Law of Static Friction
The threshold for impending slip is , never automatically .
Substitute the expression found for the perpendicular normal force () into .
CORRECTED PATH
ACEpath Teacher's DemonstrationApply horizontal equilibrium: .
Set up the condition to prevent slipping: .
Substitute and : .
Solve for the minimum compression: .
(or )
02 The student misapplies the friction formula by multiplying the normal force by the coefficient of friction instead of dividing to solve for normal force, yielding Δx_min = μs mg / k.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
Gravity: gravitational force, downward (-y) Normal force: normal force, outward (+x) Spring force: elastic force, inward (-x) Friction force: frictional force, upward (+y)
- Step 2
Vertical balance: Horizontal balance:
- Step 3Correct
When substituting into , the coefficient multiplies . Substituting gives , which requires dividing both sides by to isolate , yielding .
- Step 4Correct
Your arithmetic was carried out correctly based on your derived equation, but the final numerical result was affected by the inversion error in Step 3.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly classified all four forces acting on the block into their fundamental physical categories.
You correctly established the horizontal and vertical force balance equations for static equilibrium.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou inverted the position of the coefficient of friction when substituting into , dividing by instead of multiplying by it.
REASONING PATH
Your ACEpath teacher’s suggested approach- Direct Substitution into Friction Law
Directly replace with its expression inside the product: , then divide by the product .
- Physical Reality Check on Coefficients
Smaller friction requires greater normal force to prevent sliding ().
Check whether your formula makes physical sense: as (a smoother wall), you must compress the spring much more, meaning must be in the denominator.
CORRECTED PATH
ACEpath Teacher's DemonstrationSubstitute and into the static friction threshold condition : .
Isolate the compression: .
Substitute the given numbers: .
03 The student omits the acceleration due to gravity, confusing mass with weight when balancing vertical forces, leading to an incorrect compression value.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
Gravity: gravitational force, vertical downward Normal force: normal force, horizontal perpendicular to wall Spring force: elastic force, horizontal toward wall Friction: frictional force, vertical upward
- Step 2
Vertical equilibrium:
CorrectYou set the vertical static friction equal to the mass in kilograms rather than the downward gravitational force (weight) in newtons. Mass is an intrinsic scalar property (), whereas weight is the downward force exerted by gravity ().
- Step 3
Maximum friction:
CorrectYour reasoning using the impending slip condition is conceptually sound, but the numerical result is affected by the incorrect vertical force value from Step 2.
- Step 4Correct
You correctly related the normal force to Hooke's law for horizontal equilibrium, but your final compression inherits the error from Step 2 by a factor of ().
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly classified all four forces and their spatial orientations.
You recognized that impending motion down the wall requires static friction to reach its maximum threshold .
You balanced horizontal forces correctly by equating the spring's elastic force to the normal force.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou substituted the scalar mass as a vertical force of , forgetting to multiply by the acceleration due to gravity .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing mass (, measured in ) with weight/gravitational force (, measured in ) in Newton's second law force-balance equations.
REASONING PATH
Your ACEpath teacher’s suggested approach- Unit Consistency Check
Every term in a force balance equation must have units of force (Newtons, ).
Whenever you balance vertical forces against gravity, write explicitly with units before substituting numerical values.
- Static Friction vs. Normal Force Role
For a vertical wall, the normal force is horizontal (), while friction is vertical ().
Ensure that friction balances vertical weight () and normal force balances horizontal pushing force.
CORRECTED PATH
ACEpath Teacher's DemonstrationApply vertical equilibrium with the true gravitational force: .
At impending slip, equate friction to its maximum possible value: .
Apply horizontal equilibrium to relate the wall's normal force to the spring compression: .
Solve for the minimum compression: .
(or )
Lock it in
What determines the direction and magnitude of the normal force on an object?
is always perpendicular to the contact surface. Its magnitude is determined by Newton's laws along that perpendicular axis, not automatically by .
Similar question
A student pushes a textbook horizontally against a vertical wall with a force of . The coefficient of static friction is . Taking , determine whether the book remains at rest or slips down.
Answer
The book slips down. Normal force is . Maximum static friction is . The required upward force to balance gravity is . Since , the book remains at rest.
A block is held against a vertical wall by a force applied at an angle of above the horizontal (pushing into and up the wall). If and , write the expressions for and the vertical equilibrium equation.
Answer
Horizontal axis: . Vertical axis: (assuming impending downward slip). Impending slip condition: .
A block of mass is pressed against a vertical wall by a horizontal spring (). If the coefficient of static friction is and the spring is compressed by , find the magnitude of the actual static friction force acting on the block, and verify if it slips.
Answer
Actual friction is upward. Normal force is . Maximum available static friction is . Since , the block does not slip.