Resources

A small research submersible is designed to withstand a maximum hydrostatic gauge pressure of P=4.20 atmP = 4.20\text{ atm} in seawater (density ρ=1025 kg/m3\rho = 1025\text{ kg/m}^3). Given that 1 atm=1.013×105 Pa1\text{ atm} = 1.013 \times 10^5\text{ Pa}, 1 Pa=1 N/m21\text{ Pa} = 1\text{ N/m}^2, and the acceleration due to gravity is g=9.81 m/s2g = 9.81\text{ m/s}^2, use hydrostatic pressure relations (P=ρghP = \rho g h) and dimensional analysis to calculate the maximum safe operational depth hh in feet (ft\text{ft}), given 1 m=3.281 ft1\text{ m} = 3.281\text{ ft}. Express your answer to three significant figures.

Answer and steps

Final answer

139 ft139\text{ ft}

Steps

01

Relate Hydrostatic Pressure to Depth

Hydrostatic gauge pressure at a depth hh in a fluid of uniform density is given by: P=ρghP = \rho g h

Rearranging this formula to solve for depth hh gives: h=Pρgh = \frac{P}{\rho g}

02

Convert Pressure to SI Units (Pa\text{Pa})

Before substituting values into the formula, all quantities must be expressed in consistent SI base units. Convert the gauge pressure from atmospheres (atm\text{atm}) to pascals (Pa=N/m2\text{Pa} = \text{N/m}^2): P=4.20 atm×1.013×105 Pa1 atm=4.2546×105 PaP = 4.20\text{ atm} \times \frac{1.013 \times 10^5\text{ Pa}}{1\text{ atm}} = 4.2546 \times 10^5\text{ Pa}

03

Calculate Depth hh in Meters

Substitute the converted pressure, seawater density ρ=1025 kg/m3\rho = 1025\text{ kg/m}^3, and gravitational acceleration g=9.81 m/s2g = 9.81\text{ m/s}^2: h=4.2546×105 N/m2(1025 kg/m3)(9.81 m/s2)h = \frac{4.2546 \times 10^5\text{ N/m}^2}{(1025\text{ kg/m}^3)(9.81\text{ m/s}^2)}

Carrying out the calculation: h=4.2546×10510055.25 m≈42.312 mh = \frac{4.2546 \times 10^5}{10055.25}\text{ m} \approx 42.312\text{ m}

04

Convert Depth to Feet and Round to Significant Figures

Using the conversion factor 1 m=3.281 ft1\text{ m} = 3.281\text{ ft}: h=42.312 m×3.281 ft1 m≈138.83 fth = 42.312\text{ m} \times \frac{3.281\text{ ft}}{1\text{ m}} \approx 138.83\text{ ft}

Rounding to three significant figures gives: h≈139 fth \approx 139\text{ ft}

Common Pitfall: Directly substituting pressure in atm\text{atm} into P=ρghP = \rho g h leads to dimensional inconsistency. The formula requires pressure in pascals (N/m2\text{N/m}^2, or kg/(m⋅s2)\text{kg}/(\text{m}\cdot\text{s}^2)) so that units cancel properly to yield depth in meters.

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student confuses gauge pressure with absolute pressure and unnecessarily adds atmospheric pressure before computing depth, leading to an overcalculated safe depth of 172 ft.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    Ptotal=4.20 atm+1.00 atm=5.20 atmP_{\text{total}} = 4.20\text{ atm} + 1.00\text{ atm} = 5.20\text{ atm}

    Correct

    P=4.20 atmP = 4.20\text{ atm}

    The problem specifies that the submersible withstands a maximum hydrostatic gauge pressure of 4.20 atm4.20\text{ atm}. Hydrostatic gauge pressure is defined strictly as the pressure exerted by the fluid column alone (P=ρghP = \rho g h). Adding 1.00 atm1.00\text{ atm} computes absolute pressure rather than the gauge pressure needed for this relation.

  2. Step 2

    P=5.20×1.013×105 Pa=526760 PaP = 5.20 \times 1.013 \times 10^5\text{ Pa} = 526760\text{ Pa}

    Correct

    P=4.20 atm×1.013×105 Pa/atm=4.2546×105 PaP = 4.20\text{ atm} \times 1.013 \times 10^5\text{ Pa/atm} = 4.2546 \times 10^5\text{ Pa}

    Your conversion method from atmospheres to pascals was executed properly, but the numerical result is affected by using 5.20 atm5.20\text{ atm} instead of 4.20 atm4.20\text{ atm}.

  3. Step 3

    h=Pρg=5267601025×9.81=52.387 mh = \frac{P}{\rho g} = \frac{526760}{1025 \times 9.81} = 52.387\text{ m}

    Correct

    h=4.2546×105 Pa(1025 kg/m3)(9.81 m/s2)≈42.312 mh = \frac{4.2546 \times 10^5\text{ Pa}}{(1025\text{ kg/m}^3)(9.81\text{ m/s}^2)} \approx 42.312\text{ m}

    You rearranged and evaluated h=Pρgh = \frac{P}{\rho g} with correct SI density and gravity values, but this step inherited the inflated pressure from earlier.

  4. Step 4

    h=52.387×3.281=172 fth = 52.387 \times 3.281 = 172\text{ ft}

    Correct

    h=42.312 m×3.281 ft/m≈139 fth = 42.312\text{ m} \times 3.281\text{ ft/m} \approx 139\text{ ft}

    You converted from meters to feet correctly, but the resulting value of 172 ft172\text{ ft} stems from the initial addition of atmospheric pressure.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly used the conversion factor 1 atm=1.013×105 Pa1\text{ atm} = 1.013 \times 10^5\text{ Pa} to convert pressure to SI units.

You correctly rearranged the hydrostatic pressure formula into h=Pρgh = \frac{P}{\rho g}.

You accurately converted meters to feet using 1 m=3.281 ft1\text{ m} = 3.281\text{ ft} and rounded appropriately.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Gauge vs. Absolute Pressure Confusion

You added 1.00 atm1.00\text{ atm} of atmospheric pressure to the given pressure before solving for depth.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Gauge pressure measures pressure relative to local atmospheric pressure and is directly produced by the fluid column (Pgauge=ρghP_{\text{gauge}} = \rho g h). Total (absolute) pressure is Pabs=Patm+ρghP_{\text{abs}} = P_{\text{atm}} + \rho g h. Substituting total pressure directly into h=Pρgh = \frac{P}{\rho g} assumes the fluid surface is in a vacuum, which overestimates the water depth corresponding to that gauge limit.

REASONING PATH
Your ACEpath teacher’s suggested approach
Identify Pressure Type
  • Gauge pressure is Pgauge=ρghP_{\text{gauge}} = \rho g h, whereas absolute pressure is Pabs=Patm+ρghP_{\text{abs}} = P_{\text{atm}} + \rho g h.

  • Check whether the problem states 'gauge pressure' or 'absolute/total pressure'. If gauge pressure is given, use it directly in P=ρghP = \rho g h without adding PatmP_{\text{atm}}.

Match Formula to Given Quantity
  • The column depth formula h=Pρgh = \frac{P}{\rho g} requires PP to be the pressure difference across the fluid column, not the total pressure including the atmosphere above it.

  • Ensure the pressure substituted into Pρg\frac{P}{\rho g} represents only the fluid column's contribution.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Keep the gauge pressure as given: P=4.20 atmP = 4.20\text{ atm}.

  2. Convert to SI units: P=4.20×1.013×105 Pa=4.2546×105 PaP = 4.20 \times 1.013 \times 10^5\text{ Pa} = 4.2546 \times 10^5\text{ Pa}.

  3. Calculate depth in meters: h=4.2546×105 Pa(1025 kg/m3)(9.81 m/s2)≈42.312 mh = \frac{4.2546 \times 10^5\text{ Pa}}{(1025\text{ kg/m}^3)(9.81\text{ m/s}^2)} \approx 42.312\text{ m}.

  4. Convert to feet: h=42.312 m×3.281 ft/m≈138.83 fth = 42.312\text{ m} \times 3.281\text{ ft/m} \approx 138.83\text{ ft}.

Final answer

139 ft139\text{ ft}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the distinction between gauge pressure (PgaugeP_{\text{gauge}}) and absolute pressure (PabsP_{\text{abs}}).

  • Practice identifying whether hydrostatic problems provide gauge pressure or absolute pressure before converting units.

OverviewACEpath Teacher's Diagnosis

02 The student divides by the conversion factor instead of multiplying when converting meters to feet, obtaining an erroneous depth of 12.9 ft.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    P=4.20×1.013×105=425460 PaP = 4.20 \times 1.013 \times 10^5 = 425460\text{ Pa}

  2. Step 2

    h=4254601025×9.81=42.31 mh = \frac{425460}{1025 \times 9.81} = 42.31\text{ m}

  3. Step 3

    h=42.313.281=12.9 fth = \frac{42.31}{3.281} = 12.9\text{ ft}

    Correct

    h=42.31 m×3.281 ft1 m≈139 fth = 42.31\text{ m} \times \frac{3.281\text{ ft}}{1\text{ m}} \approx 139\text{ ft}

    You divided by 3.2813.281 instead of multiplying. Because 1 m=3.281 ft1\text{ m} = 3.281\text{ ft}, a meter is longer than a foot, so the numeric value in feet must be larger than in meters. Explicitly writing out the unit factor 3.281 ft1 m\frac{3.281\text{ ft}}{1\text{ m}} cancels meters and leaves feet in the numerator.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly converted atmospheres to pascals using scientific notation.

You correctly isolated depth hh using the hydrostatic relationship P=ρghP = \rho g h.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Inverted conversion factor

You divided by the conversion factor instead of multiplying when converting from meters to feet.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Treating unit conversion as bare number arithmetic without writing out explicit unit cancellation fractions, causing confusion over whether to multiply or divide.

REASONING PATH
Your ACEpath teacher’s suggested approach
Set Up Dimensional Cancellation
  • Always write conversion factors as fractions with the target unit in the numerator and the starting unit in the denominator: starting unit×target unitstarting unit\text{starting unit} \times \frac{\text{target unit}}{\text{starting unit}}.

  • Write out m×ftm\text{m} \times \frac{\text{ft}}{\text{m}} so that meters visibly cancel out before entering numbers into your calculator.

Perform a Magnitude Sanity Check
  • Converting to a smaller unit must yield a larger numerical value.

  • Since 1 m≈3.3 ft1\text{ m} \approx 3.3\text{ ft}, the depth in feet must be over three times the depth in meters (42.31 m×3.281>120 ft42.31\text{ m} \times 3.281 > 120\text{ ft}, not 12.9 ft12.9\text{ ft}).

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Multiply the depth in meters by the conversion ratio: h=42.312 m×3.281 ft1 mh = 42.312\text{ m} \times \frac{3.281\text{ ft}}{1\text{ m}}.

  2. Evaluate the product: h≈138.83 fth \approx 138.83\text{ ft}.

  3. Round to three significant figures: h≈139 fth \approx 139\text{ ft}.

Final answer

139 ft139\text{ ft}

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice writing unit conversion fractions with explicit unit cancellation for every multi-step conversion.

  • Check each converted quantity against a basic magnitude estimate to confirm whether the number should grow or shrink.

OverviewACEpath Teacher's Diagnosis

03 The student forgets to convert pressure from atmospheres to Pascals before substituting into the SI formula, calculating an impossibly small depth of 0.00137 ft.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    h=Pρgh = \frac{P}{\rho g}

  2. Step 2

    h=4.201025×9.81=0.0004177 mh = \frac{4.20}{1025 \times 9.81} = 0.0004177\text{ m}

    Correct

    h=4.20×1.013×105 Pa(1025 kg/m3)(9.81 m/s2)≈42.31 mh = \frac{4.20 \times 1.013 \times 10^5\text{ Pa}}{(1025\text{ kg/m}^3)(9.81\text{ m/s}^2)} \approx 42.31\text{ m}

    You substituted the pressure directly as 4.20 atm4.20\text{ atm} without converting it to the SI unit of pascals (N/m2\text{N/m}^2). Because density and gravity are given in SI base units, the pressure must be expressed in pascals (4.20×1.013×105 Pa=4.255×105 Pa4.20 \times 1.013 \times 10^5\text{ Pa} = 4.255 \times 10^5\text{ Pa}) so the units properly cancel to yield meters.

  3. Step 3

    h=0.0004177×3.281=0.00137 fth = 0.0004177 \times 3.281 = 0.00137\text{ ft}

    Correct

    h=42.312 m×3.281 ft/m≈139 fth = 42.312\text{ m} \times 3.281\text{ ft/m} \approx 139\text{ ft}

    You correctly used the conversion factor 1 m=3.281 ft1\text{ m} = 3.281\text{ ft}, but your final value was affected by the uncoverted pressure from the previous step.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly rearranged the hydrostatic pressure relation to solve for depth hh.

You selected and applied the correct conversion factor between meters and feet.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Omitted unit conversion before formula substitution

Substituting pressure in atmospheres directly into an SI formula without converting it to pascals.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Formulas in physics built on SI base and derived units (gg in m/s2\text{m/s}^2, ρ\rho in kg/m3\text{kg/m}^3) require every parameter to be in its corresponding coherent SI unit before numerical evaluation. Substituting a non-SI unit like atm\text{atm} violates dimensional consistency, yielding a calculated depth that is off by a factor of roughly 10510^5.

REASONING PATH
Your ACEpath teacher’s suggested approach
Dimensional Consistency Check
  • Every term in an SI equation must be in coherent SI units before calculation: [P]=Pa=Nm2=kgm⋅s2[P] = \text{Pa} = \frac{\text{N}}{\text{m}^2} = \frac{\text{kg}}{\text{m}\cdot\text{s}^2}.

  • Always convert non-SI input values (like atmospheres, psi, or bar) into pascals before plugging them into P=ρghP = \rho g h.

Physical Reasonableness Check
  • Submersible operating depths in real-world engineering are macroscopic lengths.

  • Pause and examine your numerical result: a calculated depth of 0.00137 ft0.00137\text{ ft} (about 0.4 mm0.4\text{ mm}) indicates a severe scale error, pointing immediately to a missing power-of-ten unit conversion.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Convert pressure: P=4.20 atm×1.013×105 Pa/atm=4.2546×105 PaP = 4.20\text{ atm} \times 1.013 \times 10^5\text{ Pa/atm} = 4.2546 \times 10^5\text{ Pa}.

  2. Calculate depth in meters: h=4.2546×105 N/m2(1025 kg/m3)(9.81 m/s2)=4.2546×10510055.25 m≈42.312 mh = \frac{4.2546 \times 10^5\text{ N/m}^2}{(1025\text{ kg/m}^3)(9.81\text{ m/s}^2)} = \frac{4.2546 \times 10^5}{10055.25}\text{ m} \approx 42.312\text{ m}.

  3. Convert depth to feet: h=42.312 m×3.281 ft/m≈138.83 fth = 42.312\text{ m} \times 3.281\text{ ft/m} \approx 138.83\text{ ft}.

Final answer

139 ft139\text{ ft}

NEXT STEPS
Final Takeaways from Your Teacher
  • Always write down explicit units next to numbers in your substitution line to catch unit mismatches before computing.

  • Check that all derived quantities have their base SI units aligned (e.g., 1 Pa=1 N/m2=1 kg/(m⋅s2)1\text{ Pa} = 1\text{ N/m}^2 = 1\text{ kg}/(\text{m}\cdot\text{s}^2)).

  • Perform a sanity check on the magnitude of your final answer to verify it fits the physical situation.

Lock it in

Similar question

01

A sensor at the bottom of an open freshwater pool (density ρ=1000 kg/m3\rho = 1000\text{ kg/m}^3) reads a gauge pressure of 24.5 kPa24.5\text{ kPa}. Using g=9.80 m/s2g = 9.80\text{ m/s}^2, determine the depth of the pool in meters.

Answer

h=2.50 mh = 2.50\text{ m}. Hydrostatic gauge pressure is P=ρghP = \rho g h, so h=Pρg=24500 Pa(1000 kg/m3)(9.80 m/s2)=2.50 mh = \frac{P}{\rho g} = \frac{24500\text{ Pa}}{(1000\text{ kg/m}^3)(9.80\text{ m/s}^2)} = 2.50\text{ m}.

02

A scuba diver experiences an absolute pressure of 3.50 atm3.50\text{ atm} in seawater (rho=1025 kg/m3\\rho = 1025\text{ kg/m}^3). If atmospheric pressure is 1.00 atm1.00\text{ atm}, 1 atm=1.013×105 Pa1\text{ atm} = 1.013 \times 10^5\text{ Pa}, and g=9.81 m/s2g = 9.81\text{ m/s}^2, calculate the diver's depth in meters to three significant figures.

Answer

h=25.2 mh = 25.2\text{ m}. First isolate gauge pressure: Pgauge=Pabs−Patm=3.50 atm−1.00 atm=2.50 atmP_{\text{gauge}} = P_{\text{abs}} - P_{\text{atm}} = 3.50\text{ atm} - 1.00\text{ atm} = 2.50\text{ atm}. Convert to pascals: P=2.50×1.013×105 Pa=2.5325×105 PaP = 2.50 \times 1.013 \times 10^5\text{ Pa} = 2.5325 \times 10^5\text{ Pa}. Compute depth: h=2.5325×105(1025)(9.81)≈25.2 mh = \frac{2.5325 \times 10^5}{(1025)(9.81)} \approx 25.2\text{ m}.

03

A cylindrical storage tank is filled with oil (rho=880 kg/m3\\rho = 880\text{ kg/m}^3). An engineer specifies that the tank base can tolerate a maximum gauge pressure of 18.0 psi18.0\text{ psi}. Given 1 psi=6895 Pa1\text{ psi} = 6895\text{ Pa}, g=9.81 m/s2g = 9.81\text{ m/s}^2, and 1 m=3.281 ft1\text{ m} = 3.281\text{ ft}, calculate the maximum safe oil depth in feet to three significant figures.

Answer

h=47.2 fth = 47.2\text{ ft}. Convert gauge pressure to SI: P=18.0 psi×6895 Pa/psi=124110 PaP = 18.0\text{ psi} \times 6895\text{ Pa/psi} = 124110\text{ Pa}. Find height in meters: h=124110 Pa(880 kg/m3)(9.81 m/s2)≈14.376 mh = \frac{124110\text{ Pa}}{(880\text{ kg/m}^3)(9.81\text{ m/s}^2)} \approx 14.376\text{ m}. Convert to feet: h=14.376 m×3.281 ft/m≈47.2 fth = 14.376\text{ m} \times 3.281\text{ ft/m} \approx 47.2\text{ ft}.

Loading workspace…