Resources

In a laboratory experiment to determine the thermal conductivity of a brass alloy using a guarded hot plate apparatus, a cylindrical brass test specimen of diameter D=50.0 mmD = 50.0\text{ mm} and length L=120.0 mmL = 120.0\text{ mm} is aligned vertically between an electric cartridge heater and a water-cooled heat sink. Thermocouples embedded along the rod centerline at positions x1=20.0 mmx_1 = 20.0\text{ mm}, x2=50.0 mmx_2 = 50.0\text{ mm}, x3=80.0 mmx_3 = 80.0\text{ mm}, and x4=110.0 mmx_4 = 110.0\text{ mm} record steady temperatures of T1=94.6∘CT_1 = 94.6^{\circ}\text{C}, T2=82.2∘CT_2 = 82.2^{\circ}\text{C}, T3=69.9∘CT_3 = 69.9^{\circ}\text{C}, and T4=57.5∘CT_4 = 57.5^{\circ}\text{C}, respectively. The electric cartridge heater draws a current of I=0.820 AI = 0.820\text{ A} at a potential difference of V=28.0 VV = 28.0\text{ V}, with a calibrated radial guard ring ensuring that 92.0%92.0\% of this input power conducts axially through the brass specimen. Calculate: (a) the magnitude of the experimental axial temperature gradient ∣dTdx∣|\frac{dT}{dx}|, and (b) the experimental thermal conductivity kbrassk_{\text{brass}} of the alloy.

Answer and steps

Final answer

(a) ∣dTdx∣=412 K/m|\frac{dT}{dx}| = 412\text{ K}/\text{m} (or ∘C/m^{\circ}\text{C}/\text{m}); (b) kbrass=26.1 W/(m⋅K)k_{\text{brass}} = 26.1\text{ W}/(\text{m}\cdot\text{K}).

Steps

Part (a): Determine the Magnitude of the Axial Temperature Gradient

Under steady-state, one-dimensional heat conduction with uniform cross-sectional area and thermal insulation (provided by the guard ring), the temperature varies linearly along the axis of the cylinder:

∣dTdx∣=ΔTΔx\left|\frac{dT}{dx}\right| = \frac{\Delta T}{\Delta x}

The thermocouples are evenly spaced along the cylinder:

  • Between x1x_1 and x2x_2: Δx=50.0 mm−20.0 mm=30.0 mm\Delta x = 50.0\text{ mm} - 20.0\text{ mm} = 30.0\text{ mm}, ΔT=94.6∘C−82.2∘C=12.4∘C\Delta T = 94.6^{\circ}\text{C} - 82.2^{\circ}\text{C} = 12.4^{\circ}\text{C}
  • Between x2x_2 and x3x_3: Δx=80.0 mm−50.0 mm=30.0 mm\Delta x = 80.0\text{ mm} - 50.0\text{ mm} = 30.0\text{ mm}, ΔT=82.2∘C−69.9∘C=12.3∘C\Delta T = 82.2^{\circ}\text{C} - 69.9^{\circ}\text{C} = 12.3^{\circ}\text{C}
  • Between x3x_3 and x4x_4: Δx=110.0 mm−80.0 mm=30.0 mm\Delta x = 110.0\text{ mm} - 80.0\text{ mm} = 30.0\text{ mm}, ΔT=69.9∘C−57.5∘C=12.4∘C\Delta T = 69.9^{\circ}\text{C} - 57.5^{\circ}\text{C} = 12.4^{\circ}\text{C}

Using the total distance between the first and last measurement stations:

Δx=x4−x1=110.0 mm−20.0 mm=90.0 mm=0.0900 m\Delta x = x_4 - x_1 = 110.0\text{ mm} - 20.0\text{ mm} = 90.0\text{ mm} = 0.0900\text{ m}

ΔT=T1−T4=94.6∘C−57.5∘C=37.1∘C=37.1 K\Delta T = T_1 - T_4 = 94.6^{\circ}\text{C} - 57.5^{\circ}\text{C} = 37.1^{\circ}\text{C} = 37.1\text{ K}

Calculate the magnitude of the temperature gradient:

∣dTdx∣=37.1 K0.0900 m≈412.22 K/m≈412 K/m(or 412 ∘C/m)\left|\frac{dT}{dx}\right| = \frac{37.1\text{ K}}{0.0900\text{ m}} \approx 412.22\text{ K/m} \approx 412\text{ K/m}\quad (\text{or } 412\,^{\circ}\text{C/m})


Part (b): Determine the Thermal Conductivity kbrassk_{\text{brass}}

  1. Calculate the axial heat transfer rate (Q˙\dot{Q}): The electrical power supplied by the heater is: Pelec=V⋅I=(28.0 V)⋅(0.820 A)=22.96 WP_{\text{elec}} = V \cdot I = (28.0\text{ V}) \cdot (0.820\text{ A}) = 22.96\text{ W}

    Since 92.0%92.0\% of this power is directed axially through the test bar: Q˙=0.920⋅Pelec=0.920⋅22.96 W=21.1232 W\dot{Q} = 0.920 \cdot P_{\text{elec}} = 0.920 \cdot 22.96\text{ W} = 21.1232\text{ W}

  2. Calculate the cross-sectional area of the cylinder (AA): The diameter is D=50.0 mm=0.0500 mD = 50.0\text{ mm} = 0.0500\text{ m}, so the radius is r=0.0250 mr = 0.0250\text{ m}: A=πD24=π(0.0500 m)24≈1.9635×10−3 m2A = \frac{\pi D^2}{4} = \frac{\pi (0.0500\text{ m})^2}{4} \approx 1.9635 \times 10^{-3}\text{ m}^2
  3. Apply Fourier's Law of Heat Conduction: In one dimension: Q˙=kbrass⋅A⋅∣dTdx∣\dot{Q} = k_{\text{brass}} \cdot A \cdot \left|\frac{dT}{dx}\right|

    Rearranging for thermal conductivity kbrassk_{\text{brass}}: kbrass=Q˙A⋅∣dTdx∣k_{\text{brass}} = \frac{\dot{Q}}{A \cdot \left|\frac{dT}{dx}\right|}

    Substitute the calculated values: kbrass=21.1232 W(1.9635×10−3 m2)⋅(412.22 K/m)≈21.12320.8094≈26.1 W/(m⋅K)k_{\text{brass}} = \frac{21.1232\text{ W}}{(1.9635 \times 10^{-3}\text{ m}^2) \cdot (412.22\text{ K/m})} \approx \frac{21.1232}{0.8094} \approx 26.1\text{ W}/(\text{m}\cdot\text{K})

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student forgets to apply the 92.0% guard efficiency factor, using the entire heater electrical power as the axial heat conduction rate.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    ΔT=94.6−57.5=37.1 ∘C  ⟹  Δx=110.0−20.0=90.0 mm=0.0900 m  ⟹  ∣dTdx∣=37.10.0900=412.2 ∘C/m\Delta T = 94.6 - 57.5 = 37.1\,^{\circ}\text{C} \implies \Delta x = 110.0 - 20.0 = 90.0\text{ mm} = 0.0900\text{ m} \implies \left|\frac{dT}{dx}\right| = \frac{37.1}{0.0900} = 412.2\,^{\circ}\text{C/m}

  2. Step 2

    P=V⋅I=22.96 W  ⟹  q=22.96 WP = V \cdot I = 22.96\text{ W} \implies q = 22.96\text{ W}

    Correct

    Q˙=0.920⋅P=0.920⋅(28.0 V)(0.820 A)=21.12 W\dot{Q} = 0.920 \cdot P = 0.920 \cdot (28.0\text{ V})(0.820\text{ A}) = 21.12\text{ W}

    You calculated the total electrical input power accurately, but you assumed all of it conducted axially through the brass rod. The problem specifies that a calibrated radial guard ring directs only 92.0%92.0\% of the input power along the axis.

  3. Step 3

    A=π⋅(0.0500)24=1.9635×10−3 m2A = \frac{\pi \cdot (0.0500)^2}{4} = 1.9635 \times 10^{-3}\text{ m}^2

  4. Step 4

    k=qA⋅∣dTdx∣=22.961.9635×10−3⋅412.2=28.4 W/(m⋅K)k = \frac{q}{A \cdot \left|\frac{dT}{dx}\right|} = \frac{22.96}{1.9635 \times 10^{-3} \cdot 412.2} = 28.4\text{ W/(m}\cdot\text{K)}

    Correct

    kbrass=Q˙A⋅∣dTdx∣=21.12 W(1.9635×10−3 m2)(412.2 K/m)≈26.1 W/(m⋅K)k_{\text{brass}} = \frac{\dot{Q}}{A \cdot \left|\frac{dT}{dx}\right|} = \frac{21.12\text{ W}}{(1.9635 \times 10^{-3}\text{ m}^2)(412.2\text{ K/m})} \approx 26.1\text{ W/(m}\cdot\text{K)}

    Your application of Fourier's law was structurally sound, but using the uncorrected heat rate of 22.96 W22.96\text{ W} instead of 21.12 W21.12\text{ W} led to an overstated thermal conductivity.

WHAT YOU DID WELL
Compliments from Your Teacher

You evaluated the axial temperature gradient accurately using the thermocouple data.

You calculated the total electrical heater power correctly using P=VIP = V I.

You determined the cross-sectional area with the correct unit conversion.

You set up Fourier's law of conduction in the correct algebraic form.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Omission of Heat Loss/Efficiency Factor

You equated the conducting heat flow Q˙\dot{Q} directly to the total heater power PP, forgetting to multiply by the 92.0%92.0\% axial transmission fraction.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

In guarded hot plate experiments, electric heaters lose a portion of heat radially or to surroundings; the heat rate entering the specimen is Q˙=η⋅Pelec\dot{Q} = \eta \cdot P_{\text{elec}}, not the raw electrical power.

REASONING PATH
Your ACEpath teacher’s suggested approach
Define the Control Surface
  • Only the heat rate entering the test specimen directly contributes to Fourier conduction.

  • Check whether an efficiency, guard factor, or percentage loss is specified between the power source and the test specimen.

Fourier's Law Energy Balance
  • Q˙axial=η⋅Pelec=kA∣dTdx∣\dot{Q}_{\text{axial}} = \eta \cdot P_{\text{elec}} = k A \left|\frac{dT}{dx}\right|

  • Substitute Q˙axial=0.920×22.96 W=21.12 W\dot{Q}_{\text{axial}} = 0.920 \times 22.96\text{ W} = 21.12\text{ W} into Fourier's law before solving for kk.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Account for the guard ring factor: Q˙=0.920⋅P=0.920⋅22.96 W=21.123 W\dot{Q} = 0.920 \cdot P = 0.920 \cdot 22.96\text{ W} = 21.123\text{ W}.

  2. Substitute the corrected heat flow into Fourier's law: k=21.123 W(1.9635×10−3 m2)(412.22 K/m)k = \frac{21.123\text{ W}}{(1.9635 \times 10^{-3}\text{ m}^2)(412.22\text{ K/m})}.

  3. Compute the final conductivity: k≈26.1 W/(m⋅K)k \approx 26.1\text{ W/(m}\cdot\text{K)}.

Final answer

(a) ∣dTdx∣=412 K/m\left|\frac{dT}{dx}\right| = 412\text{ K/m} (or ∘C/m^{\circ}\text{C/m}); (b) kbrass=26.1 W/(m⋅K)k_{\text{brass}} = 26.1\text{ W/(m}\cdot\text{K)}

NEXT STEPS
Final Takeaways from Your Teacher
  • In experimental conduction problems, always distinguish between input energy (heater electrical power) and conducted energy (axial heat flux).

  • Highlight phrases like 'guard ring', 'efficiency', or 'radial heat loss' during your initial problem reading to ensure the scaling factor is included.

OverviewACEpath Teacher's Diagnosis

02 The student uses the total specimen length of 120.0 mm instead of the actual distance between the first and last thermocouples when calculating the temperature gradient.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    ΔT=94.6−57.5=37.1 ∘C  ⟹  L=120.0 mm=0.1200 m  ⟹  ∣dTdx∣=37.1/0.1200=309.2 ∘C/m\Delta T = 94.6 - 57.5 = 37.1\,^{\circ}\text{C} \implies L = 120.0\text{ mm} = 0.1200\text{ m} \implies \left|\frac{dT}{dx}\right| = 37.1 / 0.1200 = 309.2\,^{\circ}\text{C/m}

    Correct

    Δx=x4−x1=110.0 mm−20.0 mm=90.0 mm=0.0900 m  ⟹  ∣dTdx∣=37.1 ∘C0.0900 m≈412 K/m\Delta x = x_4 - x_1 = 110.0\text{ mm} - 20.0\text{ mm} = 90.0\text{ mm} = 0.0900\text{ m} \implies \left|\frac{dT}{dx}\right| = \frac{37.1\,^{\circ}\text{C}}{0.0900\text{ m}} \approx 412\text{ K/m}

    You found the correct temperature difference between the first and fourth thermocouples, ΔT=37.1 ∘C\Delta T = 37.1\,^{\circ}\text{C}. However, you divided by the total rod length L=120.0 mmL = 120.0\text{ mm} rather than the distance between sensor 1 and sensor 4, which is Δx=x4−x1=110.0 mm−20.0 mm=90.0 mm=0.0900 m\Delta x = x_4 - x_1 = 110.0\text{ mm} - 20.0\text{ mm} = 90.0\text{ mm} = 0.0900\text{ m}.

  2. Step 2

    P=28.0⋅0.820=22.96 W  ⟹  q=0.920⋅22.96=21.12 WP = 28.0 \cdot 0.820 = 22.96\text{ W} \implies q = 0.920 \cdot 22.96 = 21.12\text{ W}

  3. Step 3

    A=π⋅(0.0500)24=1.9635×10−3 m2A = \frac{\pi \cdot (0.0500)^2}{4} = 1.9635 \times 10^{-3}\text{ m}^2

  4. Step 4

    k=21.121.9635×10−3⋅309.2=34.8 W/(m⋅K)k = \frac{21.12}{1.9635 \times 10^{-3} \cdot 309.2} = 34.8\text{ W/(m}\cdot\text{K)}

    Correct

    k=Q˙A∣dTdx∣=21.1232 W(1.9635×10−3 m2)(412.22 K/m)≈26.1 W/(m⋅K)k = \frac{\dot{Q}}{A \left|\frac{dT}{dx}\right|} = \frac{21.1232\text{ W}}{(1.9635 \times 10^{-3}\text{ m}^2)(412.22\text{ K/m})} \approx 26.1\text{ W}/(\text{m}\cdot\text{K})

    You correctly rearranged and applied Fourier's law, but your numerical result was affected by the underestimated temperature gradient from Step 1.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly calculated the net axial heat transfer rate using the heater parameters and efficiency.

You converted the specimen diameter and computed the cross-sectional area without error.

You correctly applied Fourier's law of heat conduction to solve for thermal conductivity.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Mismatched Spatial Interval

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You used the total geometric length of the specimen as the denominator for the temperature gradient, overlooking that the thermocouples measuring T1T_1 and T4T_4 are embedded at interior positions x1x_1 and x4x_4 rather than at the extreme ends of the cylinder.

REASONING PATH
Your ACEpath teacher’s suggested approach
Match Measurement Interval to Sensor Positions
  • For a linear gradient ΔTΔx\frac{\Delta T}{\Delta x}, the spatial interval Δx\Delta x must strictly span the coordinates where those exact temperatures were measured: Δx=xb−xa\Delta x = x_b - x_a.

  • Always pair ΔT=Ta−Tb\Delta T = T_a - T_b with Δx=xb−xa\Delta x = x_b - x_a. Never substitute total specimen dimensions unless the temperatures were recorded at the specimen boundaries x=0x=0 and x=Lx=L.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Find the sensor baseline distance: Δx=x4−x1=110.0 mm−20.0 mm=90.0 mm=0.0900 m\Delta x = x_4 - x_1 = 110.0\text{ mm} - 20.0\text{ mm} = 90.0\text{ mm} = 0.0900\text{ m}.

  2. Calculate the experimental gradient: ∣dTdx∣=T1−T4Δx=94.6∘C−57.5∘C0.0900 m=37.1 K0.0900 m≈412.22 K/m\left|\frac{dT}{dx}\right| = \frac{T_1 - T_4}{\Delta x} = \frac{94.6^{\circ}\text{C} - 57.5^{\circ}\text{C}}{0.0900\text{ m}} = \frac{37.1\text{ K}}{0.0900\text{ m}} \approx 412.22\text{ K/m}.

  3. Substitute into Fourier's law: k=Q˙A∣dTdx∣=21.1232 W(1.9635×10−3 m2)(412.22 K/m)≈26.1 W/(m⋅K)k = \frac{\dot{Q}}{A \left|\frac{dT}{dx}\right|} = \frac{21.1232\text{ W}}{(1.9635 \times 10^{-3}\text{ m}^2)(412.22\text{ K/m})} \approx 26.1\text{ W}/(\text{m}\cdot\text{K}).

Final answer

(a) ∣dTdx∣=412 K/m\left|\frac{dT}{dx}\right| = 412\text{ K/m}; (b) kbrass=26.1 W/(m⋅K)k_{\text{brass}} = 26.1\text{ W}/(\text{m}\cdot\text{K})

NEXT STEPS
Final Takeaways from Your Teacher
  • In experimental data problems, draw a quick coordinate line to mark sensor positions versus total specimen length.

  • Verify that every ΔT\Delta T calculation uses coordinates Δx=xfinal−xinitial\Delta x = x_{\text{final}} - x_{\text{initial}} taken from sensor stations, not the boundary endpoints.

OverviewACEpath Teacher's Diagnosis

03 The student uses the diameter directly as the radius in the area formula, calculating A = π·D² instead of π·D²/4.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    ΔT=94.6−57.5=37.1∘C  ⟹  Δx=110.0−20.0=90.0 mm=0.0900 m  ⟹  ∣dTdx∣=37.10.0900=412.2∘C/m\Delta T = 94.6 - 57.5 = 37.1^{\circ}\text{C} \implies \Delta x = 110.0 - 20.0 = 90.0\text{ mm} = 0.0900\text{ m} \implies \left|\frac{dT}{dx}\right| = \frac{37.1}{0.0900} = 412.2^{\circ}\text{C/m}

  2. Step 2

    P=28.0⋅0.820=22.96 W  ⟹  q=0.920⋅22.96=21.12 WP = 28.0 \cdot 0.820 = 22.96\text{ W} \implies q = 0.920 \cdot 22.96 = 21.12\text{ W}

  3. Step 3

    A=π⋅r2=π⋅(0.0500)2=7.854×10−3 m2A = \pi \cdot r^2 = \pi \cdot (0.0500)^2 = 7.854 \times 10^{-3}\text{ m}^2

    Correct

    A=πD24=πr2=π(0.0250 m)2≈1.9635×10−3 m2A = \frac{\pi D^2}{4} = \pi r^2 = \pi (0.0250\text{ m})^2 \approx 1.9635 \times 10^{-3}\text{ m}^2

    The given diameter is D=50.0 mm=0.0500 mD = 50.0\text{ mm} = 0.0500\text{ m}, which means the radius is r=D2=0.0250 mr = \frac{D}{2} = 0.0250\text{ m}. You substituted 0.0500 m0.0500\text{ m} for rr, resulting in an area that is 44 times too large.

  4. Step 4

    k=21.127.854×10−3⋅412.2=6.52 W/(m⋅K)k = \frac{21.12}{7.854 \times 10^{-3} \cdot 412.2} = 6.52\text{ W/(m}\cdot\text{K)}

    Correct

    k=Q˙A∣dTdx∣=21.1232 W(1.9635×10−3 m2)(412.22 K/m)≈26.1 W/(m⋅K)k = \frac{\dot{Q}}{A \left|\frac{dT}{dx}\right|} = \frac{21.1232\text{ W}}{(1.9635 \times 10^{-3}\text{ m}^2)(412.22\text{ K/m})} \approx 26.1\text{ W/(m}\cdot\text{K)}

    Your rearrangement and substitution into Fourier's law were algebraically sound, but using the quadrupled area caused your computed thermal conductivity to be divided by 44.

WHAT YOU DID WELL
Compliments from Your Teacher

You accurately computed the temperature gradient from the thermocouple readings.

You correctly calculated the axial heat conduction rate from the heater voltage, current, and fractional efficiency.

You set up Fourier's Law of Heat Conduction in the correct form.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Diameter substituted as radius

You wrote r=0.0500 mr = 0.0500\text{ m} instead of dividing the diameter D=0.0500 mD = 0.0500\text{ m} by 22.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Conflating diameter with radius when computing circular cross-sectional area, using A=πD2A = \pi D^2 rather than A=πD24A = \frac{\pi D^2}{4}.

REASONING PATH
Your ACEpath teacher’s suggested approach
Check Diameter vs. Radius
  • For a circular cross section with diameter DD, the area is A=πD24A = \frac{\pi D^2}{4} or A=πr2A = \pi r^2 where r=D2r = \frac{D}{2}.

  • Always convert diameter to radius immediately upon reading the prompt, or use A=πD24A = \frac{\pi D^2}{4} directly.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Find the radius: r=D2=0.0500 m2=0.0250 mr = \frac{D}{2} = \frac{0.0500\text{ m}}{2} = 0.0250\text{ m}.

  2. Compute the correct cross-sectional area: A=π(0.0250 m)2≈1.9635×10−3 m2A = \pi (0.0250\text{ m})^2 \approx 1.9635 \times 10^{-3}\text{ m}^2.

  3. Re-evaluate Fourier's law: k=Q˙A∣dTdx∣=21.1232 W(1.9635×10−3 m2)(412.22 K/m)≈26.1 W/(m⋅K)k = \frac{\dot{Q}}{A \left|\frac{dT}{dx}\right|} = \frac{21.1232\text{ W}}{(1.9635 \times 10^{-3}\text{ m}^2)(412.22\text{ K/m})} \approx 26.1\text{ W/(m}\cdot\text{K)}.

Final answer

(a) ∣dTdx∣=412 K/m\left|\frac{dT}{dx}\right| = 412\text{ K/m} (or ∘C/m^{\circ}\text{C/m}); (b) kbrass=26.1 W/(m⋅K)k_{\text{brass}} = 26.1\text{ W/(m}\cdot\text{K)}

NEXT STEPS
Final Takeaways from Your Teacher
  • Form the habit of writing r=D/2r = D/2 right next to the given diameter in your variable list.

  • Verify your thermal conductivity value against typical engineering materials: brass is generally between 2020 and 120 W/(m⋅K)120\text{ W/(m}\cdot\text{K)}, so 6.52 W/(m⋅K)6.52\text{ W/(m}\cdot\text{K)} should signal an area or factor-of-four error.

Lock it in

Similar question

01

A cylindrical copper rod of diameter D=40.0 mmD = 40.0\text{ mm} undergoes steady-state axial conduction. An electrical heater at one end draws 1.20 A1.20\text{ A} at 15.0 V15.0\text{ V}. If thermal guarding ensures that 95.0%95.0\% of the electrical energy flows axially into the rod, and thermocouples 60.0 mm60.0\text{ mm} apart measure a temperature difference of 1.15∘C1.15^{\circ}\text{C}, calculate the experimental thermal conductivity of the copper.

Answer

k=384 W/(m⋅K)k = 384\text{ W/(m}\cdot\text{K)}. Steps: Q˙=0.950⋅(15.0⋅1.20)=17.1 W\dot{Q} = 0.950 \cdot (15.0 \cdot 1.20) = 17.1\text{ W}; A=π(0.0400)24=1.2566×10−3 m2A = \frac{\pi(0.0400)^2}{4} = 1.2566 \times 10^{-3}\text{ m}^2; ∣dT/dx∣=1.150.0600=19.167 K/m|dT/dx| = \frac{1.15}{0.0600} = 19.167\text{ K/m}; k=17.1(1.2566×10−3)(19.167)≈384 W/(m⋅K)k = \frac{17.1}{(1.2566 \times 10^{-3})(19.167)} \approx 384\text{ W/(m}\cdot\text{K)}.

02

An aluminum cylinder (D=30.0 mmD = 30.0\text{ mm}, L=100 mmL = 100\text{ mm}) has thermal conductivity k=205 W/(m⋅K)k = 205\text{ W/(m}\cdot\text{K)}. A cartridge heater delivers 45.0 W45.0\text{ W} of total electrical power at the top, while the bottom is heat-sinked. If the measured axial temperature gradient is 280 K/m280\text{ K/m}, determine the percentage of heater power that actually conducts axially through the bar.

Answer

η=90.2%\eta = 90.2\%. Steps: A=π(0.0300)24=7.0686×10−4 m2A = \frac{\pi(0.0300)^2}{4} = 7.0686 \times 10^{-4}\text{ m}^2; Q˙axial=kA∣dT/dx∣=205⋅(7.0686×10−4)⋅280=40.57 W\dot{Q}_{\text{axial}} = k A |dT/dx| = 205 \cdot (7.0686 \times 10^{-4}) \cdot 280 = 40.57\text{ W}; Percentage efficiency = 40.57 W45.0 W×100%≈90.2%\frac{40.57\text{ W}}{45.0\text{ W}} \times 100\% \approx 90.2\%.

03

In a thermal conductivity measurement of a polymer disk (D=80.0 mmD = 80.0\text{ mm}, thickness Δx=5.00 mm\Delta x = 5.00\text{ mm}), an electric heater provides 12.0 V12.0\text{ V} and 0.500 A0.500\text{ A}. A guard heater limits radial leakage to 15.0%15.0\% of the input power. Across the disk, the measured temperature difference is 24.0∘C24.0^{\circ}\text{C}. Calculate the thermal conductivity of the polymer.

Answer

k=0.211 W/(m⋅K)k = 0.211\text{ W/(m}\cdot\text{K)}. Steps: P=12.0⋅0.500=6.00 WP = 12.0 \cdot 0.500 = 6.00\text{ W}; Q˙=(1−0.150)⋅6.00=5.10 W\dot{Q} = (1 - 0.150) \cdot 6.00 = 5.10\text{ W}; A=π(0.0800)24=5.0265×10−3 m2A = \frac{\pi(0.0800)^2}{4} = 5.0265 \times 10^{-3}\text{ m}^2; ∣dT/dx∣=24.00.00500=4800 K/m|dT/dx| = \frac{24.0}{0.00500} = 4800\text{ K/m}; k=5.10(5.0265×10−3)(4800)≈0.211 W/(m⋅K)k = \frac{5.10}{(5.0265 \times 10^{-3})(4800)} \approx 0.211\text{ W/(m}\cdot\text{K)}.

Loading workspace…