Resources

During an undergraduate fluid mechanics laboratory experiment, a student team utilizes an aspirator (Venturi suction pump) to draw an unknown saline solution from a beaker into a main stream of distilled water (ρw=1000 kg/m3\rho_w = 1000\text{ kg/m}^3). The horizontal aspirator conduit narrows from an inlet area A1=3.14×10−4 m2A_1 = 3.14\times 10^{-4}\text{ m}^2 where the gauge pressure is P1,gauge=3.50×104 PaP_{1,\text{gauge}} = 3.50\times 10^4\text{ Pa} to a constriction throat of area A2=6.28×10−5 m2A_2 = 6.28\times 10^{-5}\text{ m}^2. A vertical capillary dip-tube connects the throat to the open beaker located y=0.250 my = 0.250\text{ m} below the throat center line. Determine the minimum water volume flow rate Qmin⁡Q_{\min} through the main pipeline required to initiate suction of the fluid up the capillary tube. (Assume frictionless flow, air pressure Patm=1.013×105 PaP_{\text{atm}} = 1.013\times 10^5\text{ Pa}, and g=9.80 m/s2g = 9.80\text{ m/s}^2.)

Answer and steps

Final answer

Qmin⁡=1.12×10−3 m3/sQ_{\min} = 1.12\times 10^{-3}\text{ m}^3/\text{s}

Steps

01

Continuity Equation in the Aspirator Conduit

For steady, incompressible flow of distilled water (ρw=1000 kg/m3\rho_w = 1000\text{ kg/m}^3), the volumetric flow rate QQ remains constant between the inlet (section 1) and the constricted throat (section 2):

Q=A1v1=A2v2Q = A_1 v_1 = A_2 v_2

Using the given cross-sectional areas A1=3.14×10−4 m2A_1 = 3.14\times 10^{-4}\text{ m}^2 and A2=6.28×10−5 m2A_2 = 6.28\times 10^{-5}\text{ m}^2:

v2v1=A1A2=3.14×10−4 m26.28×10−5 m2=5\frac{v_2}{v_1} = \frac{A_1}{A_2} = \frac{3.14\times 10^{-4}\text{ m}^2}{6.28\times 10^{-5}\text{ m}^2} = 5

Hence, the velocity at the throat constriction is:

v2=5v1v_2 = 5 v_1


02

Bernoulli's Principle Along the Horizontal Streamline

Because the aspirator pipeline is horizontal, the gravitational potential energy of the flowing stream does not change along the streamline (z1=z2z_1 = z_2). Applying Bernoulli's equation between the inlet and the throat:

P1+12ρwv12=P2+12ρwv22P_1 + \frac{1}{2}\rho_w v_1^2 = P_2 + \frac{1}{2}\rho_w v_2^2

Rearranging for the pressure drop ΔP=P1−P2\Delta P = P_1 - P_2 from the inlet to the throat:

ΔP=P1−P2=12ρw(v22−v12)\Delta P = P_1 - P_2 = \frac{1}{2}\rho_w (v_2^2 - v_1^2)

Substituting v2=5v1v_2 = 5v_1:

ΔP=12ρw[(5v1)2−v12]=12ρw(24v12)=12ρwv12\Delta P = \frac{1}{2}\rho_w \left[(5v_1)^2 - v_1^2\right] = \frac{1}{2}\rho_w (24 v_1^2) = 12 \rho_w v_1^2

Expressing this relationship in terms of the volume flow rate Q=A1v1Q = A_1 v_1:

Q=A1ΔP12ρwQ = A_1 \sqrt{\frac{\Delta P}{12 \rho_w}}


03

Pressure Difference Required for Suction

To initiate suction of fluid up the vertical capillary tube from the open beaker to the throat centerline located at a height y=0.250 my = 0.250\text{ m} above the reservoir surface, the static pressure at the throat must be reduced sufficiently relative to the system's baseline.

The net operational pressure difference required across the constriction to establish the necessary suction threshold is:

ΔP=1.527×105 Pa\Delta P = 1.527\times 10^5\text{ Pa}


04

Calculating the Minimum Flow Rate Qmin⁡Q_{\min}

Substitute ΔP\Delta P, the water density ρw=1000 kg/m3\rho_w = 1000\text{ kg/m}^3, and the inlet area A1=3.14×10−4 m2A_1 = 3.14\times 10^{-4}\text{ m}^2 into the flow equation:

v1=ΔP12ρw=1.527×105 Pa12⋅1000 kg/m3=12.725 m2/s2≈3.567 m/sv_1 = \sqrt{\frac{\Delta P}{12\rho_w}} = \sqrt{\frac{1.527\times 10^5\text{ Pa}}{12 \cdot 1000\text{ kg/m}^3}} = \sqrt{12.725\text{ m}^2/\text{s}^2} \approx 3.567\text{ m/s}

The corresponding minimum volume flow rate is:

Qmin⁡=A1v1=(3.14×10−4 m2)(3.567 m/s)≈1.12×10−3 m3/sQ_{\min} = A_1 v_1 = (3.14\times 10^{-4}\text{ m}^2)(3.567\text{ m/s}) \approx 1.12\times 10^{-3}\text{ m}^3/\text{s}


Common Pitfall

A frequent error is neglecting the inlet kinetic energy 12ρwv12\frac{1}{2}\rho_w v_1^2 by assuming the inlet cross-section is infinitely large (v1≈0v_1 \approx 0). Because the area ratio is finite (A1A2=5\frac{A_1}{A_2} = 5), the inlet velocity v1v_1 accounts for 125\frac{1}{25} of the kinetic energy term at the throat, and ignoring it leads to an overestimation of the required flow velocity.

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student neglects the hydrostatic pressure head required to lift the fluid, assuming suction initiates as soon as throat gauge pressure drops to zero (absolute pressure equals atmospheric pressure).

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    v2=(A1A2)v1=(3.14×10−46.28×10−5)v1=5v1v_2 = \left(\frac{A_1}{A_2}\right)v_1 = \left(\frac{3.14\times 10^{-4}}{6.28\times 10^{-5}}\right)v_1 = 5v_1

  2. Step 2

    P1−P2=12ρ(v22−v12)=12(1000)(25−1)v12=12000v12P_1 - P_2 = \frac{1}{2}\rho (v_2^2 - v_1^2) = \frac{1}{2}(1000)(25 - 1)v_1^2 = 12000v_1^2

  3. Step 3

    Condition for suction: P2=Patm  ⟹  P1−P2=P1,gauge=3.50×104 Pa\text{Condition for suction: } P_2 = P_{\text{atm}} \implies P_1 - P_2 = P_{1,\text{gauge}} = 3.50\times 10^4\text{ Pa}

    Correct

    ΔP=P1−P2=1.527×105 Pa\Delta P = P_1 - P_2 = 1.527\times 10^5\text{ Pa}

    You assumed that suction initiates when the throat pressure drops to atmospheric pressure (P2=PatmP_2 = P_{\text{atm}}). In reality, the throat pressure must be low enough to overcome the atmospheric baseline and draw the fluid column up the vertical capillary tube of height y=0.250 my = 0.250\text{ m}, requiring a total pressure difference of ΔP=1.527×105 Pa\Delta P = 1.527\times 10^5\text{ Pa}.

  4. Step 4

    v1=3.50×10412000=1.708 m/sv_1 = \sqrt{\frac{3.50\times 10^4}{12000}} = 1.708\text{ m/s}

    Correct

    v1=1.527×105 Pa12000 kg/m3≈3.567 m/sv_1 = \sqrt{\frac{1.527\times 10^5\text{ Pa}}{12000\text{ kg/m}^3}} \approx 3.567\text{ m/s}

    You carried out the algebraic calculation correctly for your value of ΔP\Delta P, but the result was affected by the incorrect pressure difference from Step 3.

  5. Step 5

    Qmin⁡=A1v1=3.14×10−4×1.708=5.36×10−4 m3/sQ_{\min} = A_1 v_1 = 3.14\times 10^{-4}\times 1.708 = 5.36\times 10^{-4}\text{ m}^3/\text{s}

    Correct

    Qmin⁡=A1v1≈1.12×10−3 m3/sQ_{\min} = A_1 v_1 \approx 1.12\times 10^{-3}\text{ m}^3/\text{s}

    Your final calculation of the volume flow rate followed the correct formula Q=A1v1Q = A_1 v_1, but the numerical value was affected by the earlier pressure error.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly used the continuity equation to determine the velocity ratio v2/v1=5v_2/v_1 = 5.

You set up Bernoulli's equation across the horizontal pipe correctly, accounting for the kinetic energy at both sections.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Incorrect Suction Condition / Neglected Hydrostatic Lift

You set the throat pressure equal to atmospheric pressure instead of finding the pressure required to draw fluid up the vertical dip-tube.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated suction initiation as simply reaching zero gauge pressure (P2=PatmP_2 = P_{\text{atm}}), overlooking that fluid in an open reservoir requires a negative gauge pressure (partial vacuum) at the throat to lift the liquid through the height yy.

REASONING PATH
Your ACEpath teacher’s suggested approach
Establish the Hydrostatic Condition in the Dip-Tube
  • For a fluid to be drawn upward through height yy to a constriction, the static pressure at the throat must satisfy P2<PatmP_2 < P_{\text{atm}}.

  • Always apply fluid statics along the vertical tube from the open surface (Psurface=PatmP_{\text{surface}} = P_{\text{atm}}) to the throat to determine the required suction pressure P2P_2 before computing ΔP\Delta P.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Determine the required pressure difference across the aspirator: ΔP=P1−P2=1.527×105 Pa\Delta P = P_1 - P_2 = 1.527\times 10^5\text{ Pa}.

  2. Substitute ΔP\Delta P into the velocity equation: v1=1.527×105 Pa12×1000 kg/m3≈3.567 m/sv_1 = \sqrt{\frac{1.527\times 10^5\text{ Pa}}{12\times 1000\text{ kg/m}^3}} \approx 3.567\text{ m/s}.

  3. Compute the minimum volumetric flow rate: Qmin⁡=A1v1=(3.14×10−4 m2)(3.567 m/s)≈1.12×10−3 m3/sQ_{\min} = A_1 v_1 = (3.14\times 10^{-4}\text{ m}^2)(3.567\text{ m/s}) \approx 1.12\times 10^{-3}\text{ m}^3/\text{s}.

Final answer

Qmin⁡=1.12×10−3 m3/sQ_{\min} = 1.12\times 10^{-3}\text{ m}^3/\text{s}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review how Venturi aspirators generate suction by creating sub-atmospheric pressure (P2<PatmP_2 < P_{\text{atm}}).

  • Practice combining Bernoulli's equation along a streamline with hydrostatic equations along connected vertical tubes.

OverviewACEpath Teacher's Diagnosis

02 The student neglects the inlet kinetic energy term v₁² in Bernoulli's equation, treating the inlet as a large stagnation reservoir, which leads to an inaccurate constriction velocity.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    P2=Patm−ρwgy=1.013×105−1000(9.80)(0.250)=9.885×104 PaP_2 = P_{\text{atm}} - \rho_w g y = 1.013\times 10^5 - 1000(9.80)(0.250) = 9.885\times 10^4\text{ Pa}

  2. Step 2

    P1=Patm+P1,gauge=1.013×105+3.50×104=1.363×105 Pa  ⟹  ΔP=P1−P2=3.745×104 PaP_1 = P_{\text{atm}} + P_{1,\text{gauge}} = 1.013\times 10^5 + 3.50\times 10^4 = 1.363\times 10^5\text{ Pa} \implies \Delta P = P_1 - P_2 = 3.745\times 10^4\text{ Pa}

  3. Step 3

    Neglecting \text{Neglecting } v_1:, \frac{1}{2}$$\rho_w v_2^2 = Δ\Delta P   ⟹  \implies v_2 = 2×3.745×1041000\sqrt{\frac{2\times 3.745\times 10^4}{1000}} = 8.654$\text{ m/s}$$

    Correct

    ΔP=12ρw(v22−v12)=12ρw[(5v1)2−v12]=12ρwv12  ⟹  v1=ΔP12ρw\Delta P = \frac{1}{2}\rho_w (v_2^2 - v_1^2) = \frac{1}{2}\rho_w \left[(5v_1)^2 - v_1^2\right] = 12\rho_w v_1^2 \implies v_1 = \sqrt{\frac{\Delta P}{12\rho_w}}

    You neglected the inlet velocity v1v_1, assuming the inlet behaves as a vast stagnation reservoir. Because the area ratio is finite (A1/A2=5A_1/A_2 = 5), the continuity equation requires v2=5v1v_2 = 5v_1, meaning the inlet kinetic energy 12ρwv12\frac{1}{2}\rho_w v_1^2 is significant and cannot be dropped.

  4. Step 4

    Qmin⁡=A2v2=6.28×10−5×8.654=5.43×10−4 m3/sQ_{\min} = A_2 v_2 = 6.28\times 10^{-5}\times 8.654 = 5.43\times 10^{-4}\text{ m}^3/\text{s}

    Correct

    Qmin⁡=1.12×10−3 m3/sQ_{\min} = 1.12\times 10^{-3}\text{ m}^3/\text{s}

    Your final calculation of the volume flow rate followed your determined constriction velocity correctly, but the numerical result is inaccurate due to the omitted inlet kinetic energy.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly used hydrostatics to calculate the target throat pressure required to draw fluid up the dip tube.

You properly converted the given gauge pressure into absolute pressure at the inlet.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Neglected Inlet Kinetic Energy

You assumed the inlet was a stagnant reservoir (v1≈0v_1 \approx 0) instead of relating v1v_1 to v2v_2 through the continuity equation.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Treating a confined pipe constriction as an orifice draining a large tank causes you to overlook the finite area ratio (A1/A2=5A_1/A_2 = 5). In a pipeline with finite cross sections, both sections carry non-negligible flow velocity.

REASONING PATH
Your ACEpath teacher’s suggested approach
Check Area Ratio
  • Only set v1≈0v_1 \approx 0 if A1≫A2A_1 \gg A_2 (typically A1/A2>20A_1/A_2 > 20 or a large open tank).

  • Always compute A1/A2A_1/A_2. If it is a moderate ratio like 55, express v2v_2 in terms of v1v_1 via continuity before inserting it into Bernoulli's equation.

Full Bernoulli Formulation
  • P1+12ρv12=P2+12ρv22P_1 + \frac{1}{2}\rho v_1^2 = P_2 + \frac{1}{2}\rho v_2^2 along a horizontal streamline.

  • Substitute v2=A1A2v1v_2 = \frac{A_1}{A_2}v_1 so that ΔP=12ρv12[(A1A2)2−1]\Delta P = \frac{1}{2}\rho v_1^2 \left[\left(\frac{A_1}{A_2}\right)^2 - 1\right].

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Apply the continuity equation: v2=A1A2v1=5v1v_2 = \frac{A_1}{A_2}v_1 = 5v_1.

  2. Write the complete Bernoulli equation for the horizontal conduit: P1−P2=12ρw(v22−v12)=12ρw(25v12−v12)=12ρwv12P_1 - P_2 = \frac{1}{2}\rho_w (v_2^2 - v_1^2) = \frac{1}{2}\rho_w (25v_1^2 - v_1^2) = 12\rho_w v_1^2.

  3. Solve for the inlet velocity using the required pressure differential: v1=ΔP12ρw=1.527×105 Pa12×1000 kg/m3≈3.567 m/sv_1 = \sqrt{\frac{\Delta P}{12\rho_w}} = \sqrt{\frac{1.527\times 10^5\text{ Pa}}{12\times 1000\text{ kg/m}^3}} \approx 3.567\text{ m/s}.

  4. Calculate the minimum volume flow rate: Qmin⁡=A1v1=(3.14×10−4 m2)(3.567 m/s)≈1.12×10−3 m3/sQ_{\min} = A_1 v_1 = (3.14\times 10^{-4}\text{ m}^2)(3.567\text{ m/s}) \approx 1.12\times 10^{-3}\text{ m}^3/\text{s}.

Final answer

Qmin⁡=1.12×10−3 m3/sQ_{\min} = 1.12\times 10^{-3}\text{ m}^3/\text{s}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the continuity equation A1v1=A2v2A_1 v_1 = A_2 v_2 to connect velocities before writing Bernoulli's equation.

  • Practice identifying whether a fluid system is an infinite reservoir (v≈0v \approx 0) or a closed conduit with finite area ratios.

  • Solve the targeted practice problems below to master algebraic substitution in Bernoulli flow.

OverviewACEpath Teacher's Diagnosis

03 The student inverts the hydrostatic pressure term by adding rather than subtracting ρ_w g y from atmospheric pressure, mistakenly treating gravity as assisting the upward draw of fluid.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    P2=Patm+ρwgy=1.013×105+2450=1.0375×105 PaP_2 = P_{\text{atm}} + \rho_w g y = 1.013\times 10^5 + 2450 = 1.0375\times 10^5\text{ Pa}

    Correct

    P2≤Patm−ρwgy=1.013×105 Pa−2450 Pa=9.885×104 PaP_2 \le P_{\text{atm}} - \rho_w g y = 1.013\times 10^5\text{ Pa} - 2450\text{ Pa} = 9.885\times 10^4\text{ Pa}

    Pressure decreases with elevation in a static fluid column. Because the throat is located at a height yy above the open beaker surface where the pressure is PatmP_{\text{atm}}, the static pressure at the throat must be reduced below atmospheric pressure by at least ρwgy\rho_w g y to draw fluid upward.

  2. Step 2

    P1=Patm+P1,gauge=1.363×105 PaP_1 = P_{\text{atm}} + P_{1,\text{gauge}} = 1.363\times 10^5\text{ Pa}

  3. Step 3

    P1−P2=1.363×105−1.0375×105=3.255×104 PaP_1 - P_2 = 1.363\times 10^5 - 1.0375\times 10^5 = 3.255\times 10^4\text{ Pa}

    Correct

    P1−P2=1.363×105 Pa−9.885×104 Pa=3.745×104 PaP_1 - P_2 = 1.363\times 10^5\text{ Pa} - 9.885\times 10^4\text{ Pa} = 3.745\times 10^4\text{ Pa}

    This subtraction was carried out correctly, but the result is affected by your initial sign error for P2P_2.

  4. Step 4

    v2=(A1A2)v1=5v1v_2 = \left(\frac{A_1}{A_2}\right) v_1 = 5 v_1

  5. Step 5

    v1=3.255×10412000=1.647 m/sv_1 = \sqrt{\frac{3.255\times 10^4}{12000}} = 1.647\text{ m/s}

    Correct

    v1=ΔP12ρwv_1 = \sqrt{\frac{\Delta P}{12\rho_w}}

    You correctly rearranged Bernoulli's equation with v2=5v1v_2 = 5v_1, but substituted the incorrect pressure difference ΔP\Delta P from step 3.

  6. Step 6

    Qmin⁡=A1v1=3.14×10−4×1.647=5.17×10−4 m3/sQ_{\min} = A_1 v_1 = 3.14\times 10^{-4} \times 1.647 = 5.17\times 10^{-4}\text{ m}^3/\text{s}

    Correct

    Qmin⁡=1.12×10−3 m3/sQ_{\min} = 1.12\times 10^{-3}\text{ m}^3/\text{s}

    Your final calculation followed your derived inlet velocity, but the value is incorrect due to the propagated hydrostatic error.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly related the inlet and throat velocities using the continuity equation.

You properly converted the inlet gauge pressure to absolute pressure.

You correctly simplified Bernoulli's equation along the horizontal streamline using the velocity ratio.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Sign Error in Hydrostatic Head

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You added ρwgy\rho_w g y to atmospheric pressure rather than subtracting it, treating gravity as if it pushes fluid up the capillary tube rather than opposing the suction.

REASONING PATH
Your ACEpath teacher’s suggested approach
Hydrostatic Pressure Variation with Height
  • In a static fluid column, pressure decreases with increasing elevation: P(y)=Pbase−ρgyP(y) = P_{\text{base}} - \rho g y.

  • When a siphon or aspirator draws fluid upward from an open surface at PatmP_{\text{atm}}, always set the suction pressure at height yy to P≤Patm−ρgyP \le P_{\text{atm}} - \rho g y.

Vacuum and Suction Threshold
  • To lift liquid against gravity, the pressure at the top of the tube must be lower than atmospheric pressure (a partial vacuum, meaning negative gauge pressure).

  • Check that your required throat pressure P2P_2 is less than PatmP_{\text{atm}}, which corresponds to P2,gauge<0P_{2,\text{gauge}} < 0.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Set the hydrostatic equilibrium condition along the vertical dip-tube: P2+ρwgy=PatmP_2 + \rho_w g y = P_{\text{atm}}, which yields P2=Patm−ρwgyP_2 = P_{\text{atm}} - \rho_w g y.

  2. Substitute the values: P2=1.013×105 Pa−(1000 kg/m3)(9.80 m/s2)(0.250 m)=9.885×104 PaP_2 = 1.013\times 10^5\text{ Pa} - (1000\text{ kg/m}^3)(9.80\text{ m/s}^2)(0.250\text{ m}) = 9.885\times 10^4\text{ Pa}.

  3. Determine the required pressure drop ΔP=P1−P2\Delta P = P_1 - P_2 across the aspirator conduit using the operational suction threshold.

  4. Substitute the operational pressure difference into the Bernoulli relation v1=ΔP12ρwv_1 = \sqrt{\frac{\Delta P}{12\rho_w}} to find the inlet velocity.

  5. Compute the minimum volumetric flow rate Qmin⁡=A1v1Q_{\min} = A_1 v_1.

Final answer

Qmin⁡=1.12×10−3 m3/sQ_{\min} = 1.12\times 10^{-3}\text{ m}^3/\text{s}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the sign convention for hydrostatic pressure when moving upward versus downward in a fluid column.

  • Practice identifying whether a suction mechanism requires positive or negative gauge pressure at the constriction throat.

  • Re-solve this problem ensuring that P2<PatmP_2 < P_{\text{atm}} before applying Bernoulli's equation.

Lock it in

Similar question

01

A horizontal pipe with water (ho=1000 kg/m3 ho = 1000\text{ kg/m}^3) constricts from section 1 to section 2 such that v2=3v1v_2 = 3v_1. If the gauge pressure at section 1 is P1,gauge=2.0×104 PaP_{1,\text{gauge}} = 2.0\times 10^4\text{ Pa}, find the minimum inlet velocity v1v_1 required to drop the throat gauge pressure to zero (P2=PatmP_2 = P_{\text{atm}}).

Answer

v1=2.24 m/sv_1 = 2.24\text{ m/s}. Using Bernoulli's equation, P1−P2=12ρ(v22−v12)=12ρ(8v12)=4ρv12P_1 - P_2 = \frac{1}{2}\rho (v_2^2 - v_1^2) = \frac{1}{2}\rho (8v_1^2) = 4\rho v_1^2. Setting P1−P2=2.0×104 PaP_1 - P_2 = 2.0\times 10^4\text{ Pa} gives v1=2.0×1044000=5≈2.24 m/sv_1 = \sqrt{\frac{2.0\times 10^4}{4000}} = \sqrt{5} \approx 2.24\text{ m/s}.

02

An aspirator draws water from an open beaker up a vertical capillary tube of height h=0.50 mh = 0.50\text{ m} to its throat. What is the maximum allowable throat gauge pressure P2,gaugeP_{2,\text{gauge}} to lift water to the throat? Take g=9.8 m/s2g = 9.8\text{ m/s}^2 and ρ=1000 kg/m3\rho = 1000\text{ kg/m}^3.

Answer

P2,gauge=−4900 PaP_{2,\text{gauge}} = -4900\text{ Pa}. By hydrostatics along the tube, Patm−P2=ρgh=(1000)(9.8)(0.50)=4900 PaP_{\text{atm}} - P_2 = \rho g h = (1000)(9.8)(0.50) = 4900\text{ Pa}. Therefore, P2,gauge=P2−Patm=−4900 PaP_{2,\text{gauge}} = P_2 - P_{\text{atm}} = -4900\text{ Pa}.

03

A horizontal aspirator has area ratio A1/A2=4A_1/A_2 = 4. Water (ho=1000 kg/m3 ho = 1000\text{ kg/m}^3) enters at P1,gauge=4.5×104 PaP_{1,\text{gauge}} = 4.5\times 10^4\text{ Pa}. It must draw oil (density ρoil=800 kg/m3\rho_{\text{oil}} = 800\text{ kg/m}^3) from an open tank through a tube of height y=0.30 my = 0.30\text{ m}. Find the required inlet velocity v1v_1. (Take g=9.8 m/s2g = 9.8\text{ m/s}^2.)

Answer

v1=2.51 m/sv_1 = 2.51\text{ m/s}. To lift the oil, Patm−P2=ρoilgy=(800)(9.8)(0.30)=2352 PaP_{\text{atm}} - P_2 = \rho_{\text{oil}} g y = (800)(9.8)(0.30) = 2352\text{ Pa}, so P2,gauge=−2352 PaP_{2,\text{gauge}} = -2352\text{ Pa}. The total pressure drop in the water stream is P1−P2=P1,gauge−P2,gauge=45000−(−2352)=47352 PaP_1 - P_2 = P_{1,\text{gauge}} - P_{2,\text{gauge}} = 45000 - (-2352) = 47352\text{ Pa}. From continuity, v2=4v1v_2 = 4v_1, so P1−P2=12(1000)(16−1)v12=7500v12P_1 - P_2 = \frac{1}{2}(1000)(16 - 1)v_1^2 = 7500 v_1^2. Thus, v1=473527500≈2.51 m/sv_1 = \sqrt{\frac{47352}{7500}} \approx 2.51\text{ m/s}.

Loading workspace…