Resources

A uniform horizontal beam of length L=4.00 mL = 4.00\text{ m} and mass M=30.0 kgM = 30.0\text{ kg} is attached to a vertical wall by a frictionless pivot at its left end. The right end of the beam is supported by a light cable that makes an angle of θ=35.0∘\theta = 35.0^\circ above the horizontal. A worker of mass m=75.0 kgm = 75.0\text{ kg} stands on the beam at a distance of d=2.80 md = 2.80\text{ m} from the wall. Taking the acceleration due to gravity as g=9.80 m/s2g = 9.80\text{ m/s}^2, calculate the tension TT in the supporting cable.

Answer and steps

Final answer

T=1.15×103 NT = 1.15 \times 10^3\text{ N}

Steps

01

Identify the Forces and Lever Arms

To find the tension TT in the cable, we apply the condition for rotational static equilibrium: the net torque about any chosen pivot point must equal zero.

Choosing the frictionless pivot at the left end (x=0x = 0) as the rotation axis eliminates the unknown hinge reaction forces from the torque equation:

  • Weight of the beam (Wbeam=MgW_{\text{beam}} = M g): Because the beam is uniform, its center of mass is at its midpoint, so the lever arm is L2=4.00 m2=2.00 m\frac{L}{2} = \frac{4.00\text{ m}}{2} = 2.00\text{ m}. This exerts a clockwise torque.
  • Weight of the worker (Wworker=mgW_{\text{worker}} = m g): Located at a distance d=2.80 md = 2.80\text{ m} from the wall. This also exerts a clockwise torque.
  • Tension in the cable (TT): Acts at the right end (x=L=4.00 mx = L = 4.00\text{ m}) at an angle θ=35.0∘\theta = 35.0^\circ above the horizontal. Only the vertical component, T⊥=Tsin⁡θT_{\perp} = T\sin\theta, produces torque about the pivot, tending to rotate the beam counterclockwise.
02

Set Up the Rotational Equilibrium Condition

Taking counterclockwise torques as positive:

∑τ=τcable−τbeam−τworker=0\sum \tau = \tau_{\text{cable}} - \tau_{\text{beam}} - \tau_{\text{worker}} = 0

Substitute each torque expression into the equation:

(Tsin⁡θ)L−(Mg)(L2)−(mg)d=0(T \sin\theta) L - (M g) \left(\frac{L}{2}\right) - (m g) d = 0

03

Solve for the Tension TT

Rearrange the equation to isolate TT:

T=g(ML2+md)Lsin⁡θT = \frac{g \left(M \frac{L}{2} + m d\right)}{L \sin\theta}

Substitute the given numerical values:

ML2+md=(30.0 kg)(2.00 m)+(75.0 kg)(2.80 m)=60.0 kg⋅m+210.0 kg⋅m=270.0 kg⋅mM \frac{L}{2} + m d = (30.0\text{ kg})(2.00\text{ m}) + (75.0\text{ kg})(2.80\text{ m}) = 60.0\text{ kg}\cdot\text{m} + 210.0\text{ kg}\cdot\text{m} = 270.0\text{ kg}\cdot\text{m}

Numerator=(9.80 m/s2)(270.0 kg⋅m)=2646 N⋅m\text{Numerator} = (9.80\text{ m/s}^2)(270.0\text{ kg}\cdot\text{m}) = 2646\text{ N}\cdot\text{m}

Denominator=(4.00 m)sin⁡(35.0∘)≈4.00 m×0.5736=2.294 m\text{Denominator} = (4.00\text{ m})\sin(35.0^\circ) \approx 4.00\text{ m} \times 0.5736 = 2.294\text{ m}

Calculate TT:

T=2646 N⋅m2.294 m≈1153 N≈1.15×103 NT = \frac{2646\text{ N}\cdot\text{m}}{2.294\text{ m}} \approx 1153\text{ N} \approx 1.15 \times 10^3\text{ N}

Common Pitfall: Forgetting the sin⁡θ\sin\theta term or applying it to the entire horizontal distance without recognizing that the torque arises strictly from the perpendicular force component Tsin⁡θT\sin\theta at lever arm LL.

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student forgets that the beam is uniform and acts at its center of mass, mistakenly using the full length L instead of L/2 for the beam's weight torque.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    ∑τ=0 about pivot  ⟹  T⋅sin⁡(35.0∘)⋅4.00−(30.0)(9.80)(4.00)−(75.0)(9.80)(2.80)=0\sum \tau = 0 \text{ about pivot} \implies T \cdot \sin(35.0^\circ) \cdot 4.00 - (30.0)(9.80)(4.00) - (75.0)(9.80)(2.80) = 0

    Correct

    Tsin⁡(35.0∘)(4.00 m)−(30.0 kg)(9.80 m/s2)(2.00 m)−(75.0 kg)(9.80 m/s2)(2.80 m)=0T \sin(35.0^\circ)(4.00\text{ m}) - (30.0\text{ kg})(9.80\text{ m/s}^2)(2.00\text{ m}) - (75.0\text{ kg})(9.80\text{ m/s}^2)(2.80\text{ m}) = 0

    You correctly established the torque balance equation about the pivot and properly identified the cable and worker torques, but you used 4.00 m4.00\text{ m} as the lever arm for the beam's weight instead of the midpoint distance L2=2.00 m\frac{L}{2} = 2.00\text{ m}.

  2. Step 2

    T⋅4.00⋅sin⁡(35.0∘)=1176+2058  ⟹  T⋅2.294=3234T \cdot 4.00 \cdot \sin(35.0^\circ) = 1176 + 2058 \implies T \cdot 2.294 = 3234

    Correct

    T⋅2.294 m=588 N⋅m+2058 N⋅m=2646 N⋅mT \cdot 2.294\text{ m} = 588\text{ N}\cdot\text{m} + 2058\text{ N}\cdot\text{m} = 2646\text{ N}\cdot\text{m}

    Your algebra and addition were executed correctly, but the total clockwise torque was affected by the incorrect beam lever arm from the previous step.

  3. Step 3

    T=1409.6 N≈1410 NT = 1409.6\text{ N} \approx 1410\text{ N}

    Correct

    T=2646 N⋅m2.294 m≈1.15×103 NT = \frac{2646\text{ N}\cdot\text{m}}{2.294\text{ m}} \approx 1.15 \times 10^3\text{ N}

    You correctly solved for TT using your intermediate values, but the final numerical value is incorrect due to the initial lever arm error.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly recognized that the beam is in static rotational equilibrium and set ∑τ=0\sum \tau = 0 about the pivot.

You properly resolved the perpendicular component of the cable tension using Tsin⁡(35.0∘)T\sin(35.0^\circ) at the full length LL.

You correctly determined the worker's torque using their mass and specific position on the beam.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Center of Mass Lever Arm Error

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated the uniform beam's distributed gravitational force as though it acted at the far right tip (L=4.00 mL = 4.00\text{ m}) instead of at its center of mass located at the midpoint (L2=2.00 m\frac{L}{2} = 2.00\text{ m}).

REASONING PATH
Your ACEpath teacher’s suggested approach
Gravitational Torque on a Uniform Object
  • For any uniform rigid body in a uniform gravitational field, the total gravitational force acts at its geometric center of mass (L2\frac{L}{2}).

  • Always place the beam's weight vector at the midpoint L2\frac{L}{2} and measure the lever arm to that midpoint, not to the far end.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Substitute the beam's midpoint distance L2=2.00 m\frac{L}{2} = 2.00\text{ m} into the torque equation: T(4.00 m)sin⁡(35.0∘)−(30.0 kg)(9.80 m/s2)(2.00 m)−(75.0 kg)(9.80 m/s2)(2.80 m)=0T(4.00\text{ m})\sin(35.0^\circ) - (30.0\text{ kg})(9.80\text{ m/s}^2)(2.00\text{ m}) - (75.0\text{ kg})(9.80\text{ m/s}^2)(2.80\text{ m}) = 0.

  2. Compute the clockwise torques: τbeam=(30.0)(9.80)(2.00)=588 N⋅m\tau_{\text{beam}} = (30.0)(9.80)(2.00) = 588\text{ N}\cdot\text{m} and τworker=(75.0)(9.80)(2.80)=2058 N⋅m\tau_{\text{worker}} = (75.0)(9.80)(2.80) = 2058\text{ N}\cdot\text{m}, giving a sum of 2646 N⋅m2646\text{ N}\cdot\text{m}.

  3. Divide the sum of clockwise torques by the cable's effective lever arm: T=2646 N⋅m(4.00 m)sin⁡(35.0∘)=2646 N⋅m2.2943 m≈1153 NT = \frac{2646\text{ N}\cdot\text{m}}{(4.00\text{ m})\sin(35.0^\circ)} = \frac{2646\text{ N}\cdot\text{m}}{2.2943\text{ m}} \approx 1153\text{ N}.

Final answer

T=1.15×103 NT = 1.15 \times 10^3\text{ N}

NEXT STEPS
Final Takeaways from Your Teacher
  • Sketch a free-body diagram before writing equations, marking each point of force application explicitly.

  • Write the beam torque symbolically as Mg(L2)M g \left(\frac{L}{2}\right) before plugging in numerical values to prevent mixing up the beam's length with its center of mass.

OverviewACEpath Teacher's Diagnosis

02 The student mistakenly uses cos(θ) instead of sin(θ) when resolving the perpendicular component of tension that exerts torque on the horizontal beam.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    ∑τ=0 about pivot  ⟹  T⋅cos⁡(35.0∘)⋅4.00−(30.0)(9.80)(2.00)−(75.0)(9.80)(2.80)=0\sum \tau = 0 \text{ about pivot} \implies T \cdot \cos(35.0^\circ) \cdot 4.00 - (30.0)(9.80)(2.00) - (75.0)(9.80)(2.80) = 0

    Correct

    Tsin⁡(35.0∘)⋅4.00−(30.0)(9.80)(2.00)−(75.0)(9.80)(2.80)=0T \sin(35.0^\circ) \cdot 4.00 - (30.0)(9.80)(2.00) - (75.0)(9.80)(2.80) = 0

    You correctly placed the rotation axis at the left pivot and accurately calculated the clockwise torques from the beam's center of mass and the worker. However, for a horizontal beam, the lever arm is horizontal, so the force component producing torque must be perpendicular to the beam (vertical), which is Tsin⁡(35.0∘)T\sin(35.0^\circ). The component Tcos⁡(35.0∘)T\cos(35.0^\circ) is directed along the beam toward the pivot and exerts zero torque.

  2. Step 2

    T⋅4.00⋅cos⁡(35.0∘)=588+2058  ⟹  T⋅3.277=2646T \cdot 4.00 \cdot \cos(35.0^\circ) = 588 + 2058 \implies T \cdot 3.277 = 2646

    Correct

    T⋅4.00⋅sin⁡(35.0∘)=588+2058  ⟹  T⋅2.294=2646T \cdot 4.00 \cdot \sin(35.0^\circ) = 588 + 2058 \implies T \cdot 2.294 = 2646

    Your algebraic rearrangement and arithmetic are consistent, but the numerical coefficient reflects the incorrect trigonometric function from Step 1.

  3. Step 3

    T=807.5 N≈808 NT = 807.5\text{ N} \approx 808\text{ N}

    Correct

    T=26462.294≈1.15×103 NT = \frac{2646}{2.294} \approx 1.15 \times 10^3\text{ N}

    Your final calculation followed correctly from your prior step, but the resulting value is lower than the true tension due to the initial cosine substitution.

WHAT YOU DID WELL
Compliments from Your Teacher

You chose the pivot at the wall to eliminate the unknown hinge reaction forces from the torque equation.

You correctly identified the center of mass of the uniform beam at its midpoint L/2=2.00 mL/2 = 2.00\text{ m}.

You calculated the gravitational torques of both the beam and the worker with complete accuracy.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Trigonometric Component Error in Torque

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing the parallel and perpendicular force components when applying τ=rF⊥=rFsin⁡θ\tau = r F_\perp = r F \sin\theta. For a horizontal lever arm, the perpendicular component is vertical (Tsin⁡θT\sin\theta), while the horizontal component (Tcos⁡θT\cos\theta) points directly toward the pivot and contributes zero torque.

REASONING PATH
Your ACEpath teacher’s suggested approach
Identify the Perpendicular Force Component
  • Torque is produced only by the component of force perpendicular to the position vector: τ=rF⊥=rFsin⁡ϕ\tau = r F_\perp = r F \sin\phi, where ϕ\phi is the angle between r⃗\vec{r} and F⃗\vec{F}.

  • Always draw the components of the force at the point of application and explicitly ask yourself: which component is perpendicular to the beam?

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Replace cos⁡(35.0∘)\cos(35.0^\circ) with sin⁡(35.0∘)\sin(35.0^\circ) in the counterclockwise torque term: Tsin⁡(35.0∘)(4.00 m)=2646 N⋅mT \sin(35.0^\circ)(4.00\text{ m}) = 2646\text{ N}\cdot\text{m}.

  2. Evaluate the perpendicular lever arm coefficient: 4.00 m×sin⁡(35.0∘)≈4.00×0.5736=2.294 m4.00\text{ m} \times \sin(35.0^\circ) \approx 4.00 \times 0.5736 = 2.294\text{ m}.

  3. Divide the total clockwise torque by this coefficient: T=2646 N⋅m2.294 m≈1153 NT = \frac{2646\text{ N}\cdot\text{m}}{2.294\text{ m}} \approx 1153\text{ N}.

Final answer

T=1.15×103 NT = 1.15 \times 10^3\text{ N}

NEXT STEPS
Final Takeaways from Your Teacher
  • Before writing torque equations, sketch the force vector and decompose it into components along and perpendicular to the lever arm.

  • Remember that any force component whose line of action passes through the pivot produces zero torque.

OverviewACEpath Teacher's Diagnosis

03 The student ignores the angle of the cable and assumes tension acts purely vertically when balancing torque.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    Στ=0 about pivot  ⟹  T⋅4.00−(30.0)(9.80)(2.00)−(75.0)(9.80)(2.80)=0\Sigma \tau = 0\text{ about pivot} \implies T \cdot 4.00 - (30.0)(9.80)(2.00) - (75.0)(9.80)(2.80) = 0

    Correct

    Στ=(Tsin⁡(35.0∘))(4.00)−(30.0)(9.80)(2.00)−(75.0)(9.80)(2.80)=0\Sigma \tau = (T\sin(35.0^\circ))(4.00) - (30.0)(9.80)(2.00) - (75.0)(9.80)(2.80) = 0

    The cable pulls at an angle of 35.0∘35.0^\circ above the horizontal beam. Only the perpendicular component of tension, T⊥=Tsin⁡(35.0∘)T_\perp = T\sin(35.0^\circ), creates torque about the pivot. Multiplying the full tension TT directly by the beam length assumes the cable pulls at 90∘90^\circ to the beam.

  2. Step 2

    4.00⋅T=588+2058  ⟹  4.00⋅T=26464.00 \cdot T = 588 + 2058 \implies 4.00 \cdot T = 2646

    Correct

    4.00sin⁡(35.0∘)⋅T=588+2058  ⟹  2.2943⋅T=26464.00\sin(35.0^\circ) \cdot T = 588 + 2058 \implies 2.2943 \cdot T = 2646

    Your algebraic rearrangement and arithmetic were carried out correctly, but they propagate the missing sin⁡(35.0∘)\sin(35.0^\circ) factor from Step 1.

  3. Step 3

    T=661.5 N≈662 NT = 661.5\text{ N} \approx 662\text{ N}

    Correct

    T=2646 N⋅m4.00 m⋅sin⁡(35.0∘)≈1.15×103 NT = \frac{2646\text{ N}\cdot\text{m}}{4.00\text{ m} \cdot \sin(35.0^\circ)} \approx 1.15 \times 10^3\text{ N}

    This result follows directly from the missing trigonometric factor in Step 1.

WHAT YOU DID WELL
Compliments from Your Teacher

You chose the pivot at the wall, which correctly eliminated the unknown hinge reaction forces from the torque balance.

You placed the beam's weight at its center of mass (2.00 m2.00\text{ m}) and the worker's weight at the specified position (2.80 m2.80\text{ m}).

You correctly identified the signs of the opposing clockwise and counterclockwise torques.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Omission of Angle Component in Torque

No, this is a conceptual omission of resolving an angled force into its perpendicular lever component.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You used τ=F⋅r\tau = F \cdot r directly without accounting for the angle θ\theta between the force vector and the position vector. Torque depends strictly on the component perpendicular to the moment arm: τ=rFsin⁡θ\tau = r F \sin\theta (or r⊥Fr_\perp F).

REASONING PATH
Your ACEpath teacher’s suggested approach
Check Force Direction Relative to the Lever Arm
  • For a force F⃗\vec{F} applied at displacement r⃗\vec{r} from the pivot, torque magnitude is τ=rFsin⁡θ\tau = r F \sin\theta, where θ\theta is the angle between r⃗\vec{r} and F⃗\vec{F}.

  • Whenever a force is not perpendicular to the lever arm, resolve the force into components parallel and perpendicular to the arm; only the perpendicular component produces torque.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Set up the torque balance with the perpendicular component of tension: (Tsin⁡(35.0∘))(4.00 m)−(30.0 kg)(9.80 m/s2)(2.00 m)−(75.0 kg)(9.80 m/s2)(2.80 m)=0(T\sin(35.0^\circ))(4.00\text{ m}) - (30.0\text{ kg})(9.80\text{ m/s}^2)(2.00\text{ m}) - (75.0\text{ kg})(9.80\text{ m/s}^2)(2.80\text{ m}) = 0

  2. Combine the gravitational torque terms: T(4.00 m)sin⁡(35.0∘)=588 N⋅m+2058 N⋅m=2646 N⋅mT (4.00\text{ m})\sin(35.0^\circ) = 588\text{ N}\cdot\text{m} + 2058\text{ N}\cdot\text{m} = 2646\text{ N}\cdot\text{m}

  3. Isolate TT: T=2646 N⋅m(4.00 m)sin⁡(35.0∘)=26462.2943… N≈1153 NT = \frac{2646\text{ N}\cdot\text{m}}{(4.00\text{ m})\sin(35.0^\circ)} = \frac{2646}{2.2943\dots}\text{ N} \approx 1153\text{ N}

Final answer

T=1.15×103 NT = 1.15 \times 10^3\text{ N}

NEXT STEPS
Final Takeaways from Your Teacher
  • Draw the force vector T⃗\vec{T} at the end of the beam and break it into Tx=Tcos⁡θT_x = T\cos\theta (pointing along the beam toward the pivot) and Ty=Tsin⁡θT_y = T\sin\theta (perpendicular to the beam).

  • Notice that Tcos⁡θT\cos\theta passes directly through the pivot and produces zero torque, leaving only Tsin⁡θT\sin\theta to support the beam.

  • Complete the targeted flashcards and practice problems below to practice decomposing forces at arbitrary angles in static equilibrium.

Lock it in

Similar question

01

A uniform horizontal rod of length 3.00 m3.00\text{ m} and mass 12.0 kg12.0\text{ kg} is hinged to a wall at its left end and supported by a vertical wire at its right end. Calculate the tension in the wire. Take g=9.80 m/s2g = 9.80\text{ m/s}^2.

Answer

T=58.8 NT = 58.8\text{ N}. Set ∑τ=0\sum \tau = 0 about the hinge: T(L)−Mg(L2)=0  ⟹  T=12Mg=12(12.0 kg)(9.80 m/s2)=58.8 NT(L) - Mg\left(\frac{L}{2}\right) = 0 \implies T = \frac{1}{2}Mg = \frac{1}{2}(12.0\text{ kg})(9.80\text{ m/s}^2) = 58.8\text{ N}.

02

A uniform horizontal beam of length L=5.00 mL = 5.00\text{ m} and mass 40.0 kg40.0\text{ kg} is hinged at the left wall and held by a cable attached to its right end at an angle of 30.0∘30.0^\circ above the horizontal. A load of mass 20.0 kg20.0\text{ kg} sits 4.00 m4.00\text{ m} from the wall. Calculate the tension TT in the cable. Take g=9.80 m/s2g = 9.80\text{ m/s}^2.

Answer

T≈706 NT \approx 706\text{ N}. Set ∑τ=0\sum \tau = 0 about the hinge: T(5.00 m)sin⁡(30.0∘)=(40.0 kg)(9.80 m/s2)(2.50 m)+(20.0 kg)(9.80 m/s2)(4.00 m)=980 N⋅m+784 N⋅m=1764 N⋅mT(5.00\text{ m})\sin(30.0^\circ) = (40.0\text{ kg})(9.80\text{ m/s}^2)(2.50\text{ m}) + (20.0\text{ kg})(9.80\text{ m/s}^2)(4.00\text{ m}) = 980\text{ N}\cdot\text{m} + 784\text{ N}\cdot\text{m} = 1764\text{ N}\cdot\text{m}. Then T(2.50 m)=1764 N⋅m  ⟹  T=705.6 N≈706 NT(2.50\text{ m}) = 1764\text{ N}\cdot\text{m} \implies T = 705.6\text{ N} \approx 706\text{ N}.

03

A non-uniform horizontal boom of length 4.00 m4.00\text{ m} and mass 50.0 kg50.0\text{ kg} has its center of mass located 1.50 m1.50\text{ m} from a wall hinge at its left end. A support cable attaches at a distance of 3.00 m3.00\text{ m} from the hinge at an angle of 45.0∘45.0^\circ above the horizontal. Find the cable tension required to maintain equilibrium. Take g=9.80 m/s2g = 9.80\text{ m/s}^2.

Answer

T≈346 NT \approx 346\text{ N}. Set ∑τ=0\sum \tau = 0 about the hinge: T(3.00 m)sin⁡(45.0∘)=(50.0 kg)(9.80 m/s2)(1.50 m)=735 N⋅mT(3.00\text{ m})\sin(45.0^\circ) = (50.0\text{ kg})(9.80\text{ m/s}^2)(1.50\text{ m}) = 735\text{ N}\cdot\text{m}. Then T=735 N⋅m(3.00 m)sin⁡(45.0∘)≈7352.1213≈346 NT = \frac{735\text{ N}\cdot\text{m}}{(3.00\text{ m})\sin(45.0^\circ)} \approx \frac{735}{2.1213} \approx 346\text{ N}.

Loading workspace…