Resources

Water flows steadily through a horizontal circular pipe that narrows from an initial internal diameter of d1=8.00 cmd_1 = 8.00\text{ cm} to a constricted diameter of d2=4.00 cmd_2 = 4.00\text{ cm}. If the flow speed in the wide section is v1=1.25 m/sv_1 = 1.25\text{ m/s}, calculate the volumetric flow rate QQ through the pipe and the flow speed v2v_2 in the narrow constriction.

Answer and steps

Final answer

Q=6.28×10−3 m3/sQ = 6.28 \times 10^{-3}\text{ m}^3\text{/s} (or 6.28 L/s6.28\text{ L/s}), v2=5.00 m/sv_2 = 5.00\text{ m/s}

Steps

01

Calculate the Cross-Sectional Area of the Wide Section

First, express the diameter in standard SI units (meters): d1=8.00 cm=0.0800 md_1 = 8.00\text{ cm} = 0.0800\text{ m}

The cross-sectional area A1A_1 of the circular pipe in the wide section is given by: A1=πd124=π(0.0800 m)24≈5.027×10−3 m2A_1 = \frac{\pi d_1^2}{4} = \frac{\pi (0.0800\text{ m})^2}{4} \approx 5.027 \times 10^{-3}\text{ m}^2


02

Determine the Volumetric Flow Rate QQ

For steady, incompressible flow, the volumetric flow rate QQ is the product of the cross-sectional area and the average fluid velocity: Q=A1v1Q = A_1 v_1

Substitute the known values: Q=(5.027×10−3 m2)(1.25 m/s)≈6.28×10−3 m3/sQ = (5.027 \times 10^{-3}\text{ m}^2)(1.25\text{ m/s}) \approx 6.28 \times 10^{-3}\text{ m}^3\text{/s}

(Note: Since 1 m3=1000 L1\text{ m}^3 = 1000\text{ L}, this is equivalent to 6.28 L/s6.28\text{ L/s}.)


03

Apply the Equation of Continuity to Find v2v_2

For an incompressible fluid like water, mass conservation dictates that the volumetric flow rate remains constant throughout the pipe: Q=A1v1=A2v2Q = A_1 v_1 = A_2 v_2

Solving for the flow speed in the constriction v2v_2: v2=v1(A1A2)=v1(π4d12π4d22)=v1(d1d2)2v_2 = v_1 \left(\frac{A_1}{A_2}\right) = v_1 \left(\frac{\frac{\pi}{4}d_1^2}{\frac{\pi}{4}d_2^2}\right) = v_1 \left(\frac{d_1}{d_2}\right)^2

Substitute d1=8.00 cmd_1 = 8.00\text{ cm}, d2=4.00 cmd_2 = 4.00\text{ cm}, and v1=1.25 m/sv_1 = 1.25\text{ m/s}: v2=1.25 m/s×(8.00 cm4.00 cm)2=1.25 m/s×(2)2=1.25 m/s×4=5.00 m/sv_2 = 1.25\text{ m/s} \times \left(\frac{8.00\text{ cm}}{4.00\text{ cm}}\right)^2 = 1.25\text{ m/s} \times (2)^2 = 1.25\text{ m/s} \times 4 = 5.00\text{ m/s}


Common Pitfall to Avoid

A frequent error is assuming that flow velocity is inversely proportional to diameter (v∝1/dv \propto 1/d). Because area depends on the square of the diameter (A∝d2A \propto d^2), reducing the diameter by a factor of 22 decreases the cross-sectional area by a factor of 22=42^2 = 4, which quadruples the fluid speed.

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student uses the diameter directly in the area formula πd² instead of π(d/2)² or (π/4)d², resulting in a volumetric flow rate that is four times too large.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    d1=0.0800 m  ⟹  A1=πd12=π(0.0800)2=0.0201 m2d_1 = 0.0800\text{ m} \implies A_1 = \pi d_1^2 = \pi (0.0800)^2 = 0.0201\text{ m}^2

    Correct

    d1=0.0800 m  ⟹  A1=πd124=π(0.0800 m)24≈5.03×10−3 m2d_1 = 0.0800\text{ m} \implies A_1 = \frac{\pi d_1^2}{4} = \frac{\pi (0.0800\text{ m})^2}{4} \approx 5.03 \times 10^{-3}\text{ m}^2

    You converted d1d_1 to meters correctly, but you used A=πd2A = \pi d^2 rather than A=πr2=πd24A = \pi r^2 = \frac{\pi d^2}{4}. Substituting the diameter directly into πd2\pi d^2 overestimates the area by a factor of 44.

  2. Step 2

    Q=A1v1=0.0201×1.25=0.0251 m3/sQ = A_1 v_1 = 0.0201 \times 1.25 = 0.0251\text{ m}^3\text{/s}

    Correct

    Q=A1v1=(5.027×10−3 m2)(1.25 m/s)≈6.28×10−3 m3/sQ = A_1 v_1 = (5.027 \times 10^{-3}\text{ m}^2)(1.25\text{ m/s}) \approx 6.28 \times 10^{-3}\text{ m}^3\text{/s}

    You correctly multiplied area by flow speed to find QQ, but because A1A_1 was four times too large, your calculated flow rate became 0.0251 m3/s0.0251\text{ m}^3\text{/s} instead of 6.28×10−3 m3/s6.28 \times 10^{-3}\text{ m}^3\text{/s}.

  3. Step 3

    A2=πd22=π(0.0400)2=0.00503 m2  ⟹  v2=QA2=0.02510.00503=5.00 m/sA_2 = \pi d_2^2 = \pi (0.0400)^2 = 0.00503\text{ m}^2 \implies v_2 = \frac{Q}{A_2} = \frac{0.0251}{0.00503} = 5.00\text{ m/s}

    Correct

    A2=πd224=1.257×10−3 m2  ⟹  v2=QA2=6.28×10−3 m3/s1.257×10−3 m2=5.00 m/sA_2 = \frac{\pi d_2^2}{4} = 1.257 \times 10^{-3}\text{ m}^2 \implies v_2 = \frac{Q}{A_2} = \frac{6.28 \times 10^{-3}\text{ m}^3\text{/s}}{1.257 \times 10^{-3}\text{ m}^2} = 5.00\text{ m/s}

    You correctly applied the continuity relation v2=QA2v_2 = \frac{Q}{A_2}. Although both QQ and A2A_2 had the extra factor of 44 from using πd2\pi d^2, that factor canceled out in the ratio, allowing you to reach the correct speed v2=5.00 m/sv_2 = 5.00\text{ m/s}.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly converted the pipe diameters from centimeters to meters.

You used the correct relationship Q=AvQ = A v for volumetric flow rate.

You successfully applied the conservation of mass principle through the continuity equation Q=A1v1=A2v2Q = A_1 v_1 = A_2 v_2.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Formula Confusion: Diameter vs Radius in Circle Area

You substituted the diameter directly into πd2\pi d^2 instead of dividing by 22 to find the radius or using π4d2\frac{\pi}{4}d^2.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing the radius rr and diameter dd in the geometric area formula A=πr2A = \pi r^2. Because d=2rd = 2r, squaring the diameter without dividing by 44 produces 4πr24\pi r^2, which is four times the true cross-sectional area.

REASONING PATH
Your ACEpath teacher’s suggested approach
Area in Terms of Diameter
  • For a circular pipe, A=πr2=π(d2)2=π4d2A = \pi r^2 = \pi \left(\frac{d}{2}\right)^2 = \frac{\pi}{4}d^2.

  • Whenever a problem specifies diameter dd, either compute r=d2r = \frac{d}{2} first or write π4d2\frac{\pi}{4}d^2 before calculating.

Cancellation in Ratios
  • Ratios like A1A2=(d1d2)2\frac{A_1}{A_2} = \left(\frac{d_1}{d_2}\right)^2 remain correct even if the scale factor π4\frac{\pi}{4} is omitted, but absolute quantities like Q=AvQ = Av depend directly on the exact area.

  • Always double-check absolute values (AA, QQ, mass flow rate) independently of velocity ratios.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Find the radius r1=d12=0.0800 m2=0.0400 mr_1 = \frac{d_1}{2} = \frac{0.0800\text{ m}}{2} = 0.0400\text{ m}, or use A1=π4d12A_1 = \frac{\pi}{4}d_1^2.

  2. Calculate A1=π(0.0400 m)2≈5.027×10−3 m2A_1 = \pi (0.0400\text{ m})^2 \approx 5.027 \times 10^{-3}\text{ m}^2.

  3. Calculate the volumetric flow rate: Q=A1v1=(5.027×10−3 m2)(1.25 m/s)≈6.28×10−3 m3/sQ = A_1 v_1 = (5.027 \times 10^{-3}\text{ m}^2)(1.25\text{ m/s}) \approx 6.28 \times 10^{-3}\text{ m}^3\text{/s}.

Final answer

Q=6.28×10−3 m3/sQ = 6.28 \times 10^{-3}\text{ m}^3\text{/s} (or 6.28 L/s6.28\text{ L/s}), v2=5.00 m/sv_2 = 5.00\text{ m/s}

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice converting given diameters to radii as the very first written step in geometric physics problems.

  • Review the distinction between A=πr2A = \pi r^2 and A=π4d2A = \frac{\pi}{4}d^2 with the follow-up flashcards.

  • Solve fluid continuity problems where you determine both absolute volumetric rate QQ and fluid speeds.

OverviewACEpath Teacher's Diagnosis

02 The student forgets to convert the diameter from centimeters to meters before squaring, resulting in a volumetric flow rate off by four orders of magnitude.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    r1=8.00/2=4.00 cm  ⟹  A1=πr12=π(4.00)2=50.27 cm2r_1 = 8.00 / 2 = 4.00\text{ cm} \implies A_1 = \pi r_1^2 = \pi (4.00)^2 = 50.27\text{ cm}^2

  2. Step 2

    Q=A1v1=50.27×1.25=62.8 m3/sQ = A_1 v_1 = 50.27 \times 1.25 = 62.8\text{ m}^3\text{/s}

    Correct

    Q=A1v1=(5.027×10−3 m2)(1.25 m/s)=6.28×10−3 m3/sQ = A_1 v_1 = (5.027 \times 10^{-3}\text{ m}^2)(1.25\text{ m/s}) = 6.28 \times 10^{-3}\text{ m}^3\text{/s}

    You multiplied an area in cm2\text{cm}^2 by a velocity in m/s\text{m/s} without converting units, resulting in 62.8 cm2⋅m/s62.8\text{ cm}^2\cdot\text{m/s} rather than the expected SI unit m3/s\text{m}^3\text{/s}. Because 1 m2=10,000 cm21\text{ m}^2 = 10{,}000\text{ cm}^2, the true value is 6.28×10−3 m3/s6.28 \times 10^{-3}\text{ m}^3\text{/s}.

  3. Step 3

    r2=4.00/2=2.00 cm  ⟹  A2=π(2.00)2=12.57 cm2  ⟹  v2=(A1A2)×v1=(50.2712.57)×1.25=5.00 m/sr_2 = 4.00 / 2 = 2.00\text{ cm} \implies A_2 = \pi (2.00)^2 = 12.57\text{ cm}^2 \implies v_2 = \left(\frac{A_1}{A_2}\right) \times v_1 = \left(\frac{50.27}{12.57}\right) \times 1.25 = 5.00\text{ m/s}

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly calculated the cross-sectional areas of both pipe segments from their diameters.

You applied the equation of continuity A1v1=A2v2A_1 v_1 = A_2 v_2 accurately to find v2v_2.

You recognized that area ratios allow identical units to cancel out when solving for speed.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Unit Conversion Omission in Area

No

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated mixed units (cm2\text{cm}^2 and m/s\text{m/s}) as if they were base SI units, overlooking that area scales with the square of the length conversion factor (1 cm2=10−4 m21\text{ cm}^2 = 10^{-4}\text{ m}^2).

REASONING PATH
Your ACEpath teacher’s suggested approach
Standard SI Unit Harmonization
  • In fluid dynamics equations involving absolute quantities such as flow rate Q=AvQ = Av, all length-based parameters must share the same unit (meters) before multiplication.

  • Convert lengths to meters (d=0.0800 md = 0.0800\text{ m}) before squaring to find area in m2\text{m}^2.

Area Unit Conversion Factor
  • When converting area units, remember that 1 cm2=(10−2 m)2=10−4 m21\text{ cm}^2 = (10^{-2}\text{ m})^2 = 10^{-4}\text{ m}^2, not 10−2 m210^{-2}\text{ m}^2.

  • If you compute area in cm2\text{cm}^2, multiply by 10−410^{-4} to convert to m2\text{m}^2 before multiplying by velocity in m/s\text{m/s}.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Convert A1A_1 to square meters: A1=50.27 cm2×10−4 m2/cm2=5.027×10−3 m2A_1 = 50.27\text{ cm}^2 \times 10^{-4}\text{ m}^2\text{/cm}^2 = 5.027 \times 10^{-3}\text{ m}^2.

  2. Multiply by flow speed in standard SI units: Q=A1v1=(5.027×10−3 m2)(1.25 m/s)=6.28×10−3 m3/sQ = A_1 v_1 = (5.027 \times 10^{-3}\text{ m}^2)(1.25\text{ m/s}) = 6.28 \times 10^{-3}\text{ m}^3\text{/s}.

Final answer

Q=6.28×10−3 m3/sQ = 6.28 \times 10^{-3}\text{ m}^3\text{/s} (or 6.28 L/s6.28\text{ L/s}), v2=5.00 m/sv_2 = 5.00\text{ m/s}

NEXT STEPS
Final Takeaways from Your Teacher
  • Always convert linear dimensions into base meters before calculating areas and volumes in SI formulas.

  • Perform explicit dimensional analysis on derived values like QQ to ensure units combine to m3/s\text{m}^3\text{/s}.

OverviewACEpath Teacher's Diagnosis

03 The student assumes flow speed is inversely proportional to diameter rather than diameter squared, underestimating the speed in the narrow section.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    r1=4.00 cm=0.0400 m  ⟹  A1=π(0.0400)2=0.00503 m2  ⟹  Q=0.00503×1.25=0.00629 m3/sr_1 = 4.00\text{ cm} = 0.0400\text{ m} \implies A_1 = \pi(0.0400)^2 = 0.00503\text{ m}^2 \implies Q = 0.00503 \times 1.25 = 0.00629\text{ m}^3\text{/s}

  2. Step 2

    d1v1=d2v2  ⟹  v2=v1(d1/d2)=1.25×(8.004.00)=2.50 m/sd_1 v_1 = d_2 v_2 \implies v_2 = v_1(d_1/d_2) = 1.25 \times \left(\frac{8.00}{4.00}\right) = 2.50\text{ m/s}

    Correct

    A1v1=A2v2  ⟹  v2=v1(d1d2)2=1.25×(8.004.00)2=5.00 m/sA_1 v_1 = A_2 v_2 \implies v_2 = v_1 \left(\frac{d_1}{d_2}\right)^2 = 1.25 \times \left(\frac{8.00}{4.00}\right)^2 = 5.00\text{ m/s}

    You wrote d1v1=d2v2d_1 v_1 = d_2 v_2, treating velocity as inversely proportional to diameter. The equation of continuity equates flow rates via cross-sectional areas (A1v1=A2v2A_1 v_1 = A_2 v_2). Because area depends on diameter squared (A∝d2A \propto d^2), reducing the diameter by a factor of 22 reduces area by a factor of 44, which quadruples the flow speed to 5.00 m/s5.00\text{ m/s}.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly converted the diameter to radius in meters.

You accurately calculated the cross-sectional area of the wide pipe section.

You properly applied the formula Q=AvQ = A v to find the volumetric flow rate.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Linear Diameter Continuity Error

You omitted squaring the diameter ratio in the continuity equation, setting d1v1=d2v2d_1 v_1 = d_2 v_2 instead of d12v1=d22v2d_1^2 v_1 = d_2^2 v_2.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing linear dimensions with cross-sectional area in continuity relationships, overlooking that area scales quadratically with diameter (A=πd24A = \frac{\pi d^2}{4}).

REASONING PATH
Your ACEpath teacher’s suggested approach
Continuity Relates Area to Velocity
  • For an incompressible fluid, flow rate conservation requires A1v1=A2v2A_1 v_1 = A_2 v_2, which expands to πd124v1=πd224v2\frac{\pi d_1^2}{4} v_1 = \frac{\pi d_2^2}{4} v_2.

  • Always begin with the area equation A1v1=A2v2A_1 v_1 = A_2 v_2 before substituting diameters to ensure the square terms are preserved.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Apply the continuity equation for incompressible flow: A1v1=A2v2A_1 v_1 = A_2 v_2.

  2. Express cross-sectional areas in terms of diameters: πd124v1=πd224v2  ⟹  v2=v1(d1d2)2\frac{\pi d_1^2}{4} v_1 = \frac{\pi d_2^2}{4} v_2 \implies v_2 = v_1 \left(\frac{d_1}{d_2}\right)^2.

  3. Substitute the numerical values: v2=1.25 m/s×(8.00 cm4.00 cm)2=1.25 m/s×(2)2=5.00 m/sv_2 = 1.25\text{ m/s} \times \left(\frac{8.00\text{ cm}}{4.00\text{ cm}}\right)^2 = 1.25\text{ m/s} \times (2)^2 = 5.00\text{ m/s}.

Final answer

Q=6.28×10−3 m3/sQ = 6.28 \times 10^{-3}\text{ m}^3\text{/s} (or 6.29×10−3 m3/s6.29 \times 10^{-3}\text{ m}^3\text{/s}), v2=5.00 m/sv_2 = 5.00\text{ m/s}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review geometric scaling to reinforce that 2D cross-sectional area scales with diameter squared (A∝d2A \propto d^2).

  • Practice solving continuity problems by directly using the ratio form v2=v1(d1/d2)2v_2 = v_1 (d_1 / d_2)^2.

Lock it in

Similar question

01

Oil flows at 2.0 m/s2.0\text{ m/s} through a pipe with diameter d=10.0 cmd = 10.0\text{ cm}. What is the volumetric flow rate QQ in m3/s\text{m}^3\text{/s}?

Answer

Q≈1.57×10−2 m3/sQ \approx 1.57 \times 10^{-2}\text{ m}^3\text{/s}. Steps: r=0.050 mr = 0.050\text{ m}; A=πr2=π(0.050 m)2≈7.854×10−3 m2A = \pi r^2 = \pi (0.050\text{ m})^2 \approx 7.854 \times 10^{-3}\text{ m}^2; Q=Av=(7.854×10−3 m2)(2.0 m/s)≈1.57×10−2 m3/sQ = Av = (7.854 \times 10^{-3}\text{ m}^2)(2.0\text{ m/s}) \approx 1.57 \times 10^{-2}\text{ m}^3\text{/s}.

02

A garden hose with an internal diameter of 1.60 cm1.60\text{ cm} carries water with a speed of 0.75 m/s0.75\text{ m/s}. It connects to a nozzle with diameter 0.40 cm0.40\text{ cm}. Find the volumetric flow rate QQ through the hose and the exit speed vnozzlev_{\text{nozzle}}.

Answer

Q≈1.51×10−4 m3/sQ \approx 1.51 \times 10^{-4}\text{ m}^3\text{/s} (or 0.151 L/s0.151\text{ L/s}), vnozzle=12.0 m/sv_{\text{nozzle}} = 12.0\text{ m/s}. Steps: r1=0.0080 m  ⟹  A1=π(0.0080)2≈2.011×10−4 m2r_1 = 0.0080\text{ m} \implies A_1 = \pi (0.0080)^2 \approx 2.011 \times 10^{-4}\text{ m}^2; Q=A1v1=(2.011×10−4)(0.75)≈1.51×10−4 m3/sQ = A_1 v_1 = (2.011 \times 10^{-4})(0.75) \approx 1.51 \times 10^{-4}\text{ m}^3\text{/s}; by continuity, v2=v1(d1d2)2=0.75×(1.600.40)2=0.75×16=12.0 m/sv_2 = v_1 \left(\frac{d_1}{d_2}\right)^2 = 0.75 \times \left(\frac{1.60}{0.40}\right)^2 = 0.75 \times 16 = 12.0\text{ m/s}.

03

A syringe has a barrel diameter of 1.20 cm1.20\text{ cm} and a needle diameter of 0.60 mm0.60\text{ mm}. A nurse depresses the plunger so that 5.0 mL5.0\text{ mL} (5.0×10−6 m35.0 \times 10^{-6}\text{ m}^3) of medicine is ejected over 2.5 s2.5\text{ s}. Find the volumetric flow rate QQ, the speed of the plunger vbarrelv_{\text{barrel}}, and the exit speed from the needle vneedlev_{\text{needle}}.

Answer

Q=2.0×10−6 m3/sQ = 2.0 \times 10^{-6}\text{ m}^3\text{/s}, vbarrel≈0.0177 m/sv_{\text{barrel}} \approx 0.0177\text{ m/s} (1.77 cm/s1.77\text{ cm/s}), vneedle≈7.07 m/sv_{\text{needle}} \approx 7.07\text{ m/s}. Steps: Q=ΔVΔt=5.0×10−6 m32.5 s=2.0×10−6 m3/sQ = \frac{\Delta V}{\Delta t} = \frac{5.0 \times 10^{-6}\text{ m}^3}{2.5\text{ s}} = 2.0 \times 10^{-6}\text{ m}^3\text{/s}; Abarrel=π4(0.0120 m)2≈1.131×10−4 m2  ⟹  vbarrel=QAbarrel≈0.0177 m/sA_{\text{barrel}} = \frac{\pi}{4}(0.0120\text{ m})^2 \approx 1.131 \times 10^{-4}\text{ m}^2 \implies v_{\text{barrel}} = \frac{Q}{A_{\text{barrel}}} \approx 0.0177\text{ m/s}; Aneedle=π4(0.00060 m)2≈2.827×10−7 m2  ⟹  vneedle=QAneedle≈7.07 m/sA_{\text{needle}} = \frac{\pi}{4}(0.00060\text{ m})^2 \approx 2.827 \times 10^{-7}\text{ m}^2 \implies v_{\text{needle}} = \frac{Q}{A_{\text{needle}}} \approx 7.07\text{ m/s}.

Loading workspace…