Resources

A calibrated mechanical launch device of mass M=2.50 kgM = 2.50\text{ kg} is compressed downward against an ideal vertical linear spring with force constant k=1.96×103 N/mk = 1.96 \times 10^3\text{ N/m} by a displacement of Δy=0.350 m\Delta y = 0.350\text{ m} below its uncompressed equilibrium length. Upon release from rest, the spring accelerates the block vertically upward. The block detaches cleanly from the spring precisely as the spring returns to its uncompressed equilibrium state, entering unpowered vertical projectile motion under gravity (g=9.80 m/s2g = 9.80\text{ m/s}^2). Neglecting frictional losses and air drag, find the total maximum vertical elevation htotalh_{\text{total}} reached by the block above its initial compressed release point.

Answer and steps

Final answer

htotal=4.90 mh_{\text{total}} = 4.90\text{ m}

Steps

01

Identify Reference Levels and Initial Energy

Method: Conservation of Mechanical Energy

The motion consists of two consecutive stages:

  1. Spring launch phase: The spring expands from maximum compression back to its uncompressed equilibrium length, accelerating the block upward.
  2. Free vertical projectile phase: The block detaches cleanly from the spring and rises solely under the influence of gravity until it comes momentarily to rest at its peak. Because friction and air resistance are negligible, the total mechanical energy of the block-spring-Earth system is conserved throughout the entire process.

Choose the release position (the lowest point, where the spring is compressed by Δy=0.350 m\Delta y = 0.350\text{ m}) as the reference level for gravitational potential energy: y1=0 m  ⟹  Ug1=0 Jy_1 = 0\text{ m} \implies U_{g1} = 0\text{ J}

At this initial state, the block is released from rest:

  • Kinetic energy: K1=0 JK_1 = 0\text{ J}
  • Elastic potential energy stored in the spring: Us1=12k(Δy)2U_{s1} = \frac{1}{2}k(\Delta y)^2

Therefore, the total initial mechanical energy E1E_1 is: E1=K1+Ug1+Us1=12k(Δy)2E_1 = K_1 + U_{g1} + U_{s1} = \frac{1}{2}k(\Delta y)^2


02

Identify Energy at the Peak

At the highest point of the vertical projectile motion (y=htotaly = h_{\text{total}}):

  • The block comes momentarily to rest at its maximum elevation, so K2=0 JK_2 = 0\text{ J}.
  • The block has detached from the spring, and the spring is at its uncompressed length, so Us2=0 JU_{s2} = 0\text{ J}.
  • The gravitational potential energy is: Ug2=MghtotalU_{g2} = M g h_{\text{total}}

Thus, the total final mechanical energy E2E_2 is: E2=MghtotalE_2 = M g h_{\text{total}}


03

Solve for the Total Height htotalh_{\text{total}}

Equating initial and final mechanical energies (E1=E2E_1 = E_2): 12k(Δy)2=Mghtotal\frac{1}{2}k(\Delta y)^2 = M g h_{\text{total}}

Solving for htotalh_{\text{total}}: htotal=k(Δy)22Mgh_{\text{total}} = \frac{k(\Delta y)^2}{2 M g}

Substitute the given numerical values:

  • k=1.96×103 N/m=1960 N/mk = 1.96 \times 10^3\text{ N/m} = 1960\text{ N/m}
  • Δy=0.350 m\Delta y = 0.350\text{ m}
  • M=2.50 kgM = 2.50\text{ kg}
  • g=9.80 m/s2g = 9.80\text{ m/s}^2

htotal=1960⋅(0.350)22⋅2.50⋅9.80h_{\text{total}} = \frac{1960 \cdot (0.350)^2}{2 \cdot 2.50 \cdot 9.80}

Calculate the numerator and denominator: Numerator=1960⋅0.1225=240.1 J\text{Numerator} = 1960 \cdot 0.1225 = 240.1\text{ J} Denominator=49.0 N\text{Denominator} = 49.0\text{ N}

htotal=240.149.0=4.90 mh_{\text{total}} = \frac{240.1}{49.0} = 4.90\text{ m}


Common Pitfall to Avoid

A common mistake is finding only the additional projectile height above the detachment point and forgetting to include the initial displacement Δy=0.350 m\Delta y = 0.350\text{ m} through which the spring pushed the block. Applying energy conservation directly between the release point and the apex automatically accounts for the entire vertical displacement htotalh_{\text{total}}.

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student forgets to square the displacement in the elastic potential energy formula, calculating E = (1/2)*k*Δy instead of (1/2)*k*(Δy)².

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    Ee=12∗k∗Δy  ⟹  Ee=12∗(1960)∗(0.350)=343 JE_e = \frac{1}{2} * k * \Delta y \implies E_e = \frac{1}{2} * (1960) * (0.350) = 343\text{ J}

    Correct

    Ee=12k(Δy)2=12(1960)(0.350)2=240.1 JE_e = \frac{1}{2}k(\Delta y)^2 = \frac{1}{2}(1960)(0.350)^2 = 240.1\text{ J}

    You forgot to square the displacement Δy\Delta y in the elastic potential energy formula. Hooke's law potential energy is quadratic with displacement: Us=12k(Δy)2U_s = \frac{1}{2}k(\Delta y)^2.

  2. Step 2

    M∗g∗htotal=343  ⟹  (2.50)∗(9.80)∗htotal=343  ⟹  24.5∗htotal=343M * g * h_{\text{total}} = 343 \implies (2.50)*(9.80)*h_{\text{total}} = 343 \implies 24.5 * h_{\text{total}} = 343

    Correct

    Mghtotal=240.1  ⟹  (2.50)(9.80)htotal=240.1  ⟹  24.5htotal=240.1M g h_{\text{total}} = 240.1 \implies (2.50)(9.80)h_{\text{total}} = 240.1 \implies 24.5 h_{\text{total}} = 240.1

    Your setup equating the peak gravitational potential energy MghtotalM g h_{\text{total}} to the initial stored energy is conceptually correct, but it inherits the incorrect value of 343 J343\text{ J} from Step 1.

  3. Step 3

    htotal=14.0 mh_{\text{total}} = 14.0\text{ m}

    Correct

    htotal=4.90 mh_{\text{total}} = 4.90\text{ m}

    Carrying forward the corrected energy 240.1 J240.1\text{ J} yields htotal=240.124.5=4.90 mh_{\text{total}} = \frac{240.1}{24.5} = 4.90\text{ m}.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified that the total mechanical energy of the system is conserved between the release point and the peak.

You chose the initial compressed position as the reference height so that Ug=MghtotalU_g = M g h_{\text{total}} accounts for the entire vertical ascent.

You performed the algebraic evaluation and division accurately based on your substituted numbers.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Missing exponent in spring potential energy

You wrote the displacement as Δy\Delta y rather than (Δy)2(\Delta y)^2 in the elastic energy equation.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing the spring force formula Fs=kΔyF_s = k\Delta y (or an average force expression 12F=12kΔy\frac{1}{2}F = \frac{1}{2}k\Delta y) with the stored elastic potential energy formula Us=12k(Δy)2U_s = \frac{1}{2}k(\Delta y)^2, leading to an expression with the wrong physical dimensions of energy.

REASONING PATH
Your ACEpath teacher’s suggested approach
Dimensional Consistency Check
  • Energy has dimensions of force×distance=N⋅m=J\text{force} \times \text{distance} = \text{N}\cdot\text{m} = \text{J}. Since the spring constant kk is in N/m\text{N/m}, kΔyk\Delta y has units of N\text{N} (force), not energy.

  • Always multiply the spring constant by distance squared: [k(Δx)2]=(N/m)⋅m2=N⋅m=J[k(\Delta x)^2] = (\text{N/m})\cdot\text{m}^2 = \text{N}\cdot\text{m} = \text{J}.

Spring Potential Energy Formula
  • Us=∫0Δyky dy=12k(Δy)2U_s = \int_0^{\Delta y} k y\,dy = \frac{1}{2}k(\Delta y)^2.

  • Whenever calculating stored spring energy, explicitly write out (Δy)2(\Delta y)^2 with parentheses before substituting numerical values.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Calculate the stored elastic energy with displacement squared: Ee=12(1960 N/m)(0.350 m)2=240.1 JE_e = \frac{1}{2}(1960\text{ N/m})(0.350\text{ m})^2 = 240.1\text{ J}.

  2. Equate this to the gravitational potential energy at the peak: Mghtotal=240.1 JM g h_{\text{total}} = 240.1\text{ J}.

  3. Substitute M=2.50 kgM = 2.50\text{ kg} and g=9.80 m/s2g = 9.80\text{ m/s}^2: 24.5⋅htotal=240.124.5\cdot h_{\text{total}} = 240.1.

Final answer

htotal=4.90 mh_{\text{total}} = 4.90\text{ m}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the distinction between spring force F=kxF = kx and stored elastic potential energy U=12kx2U = \frac{1}{2}kx^2.

  • Perform unit checks on formulas before substituting values to catch missing exponents.

  • Work through practice problems involving vertical spring launchers to solidify two-stage and direct energy conservation methods.

OverviewACEpath Teacher's Diagnosis

02 The student measures the gravitational potential energy height from the uncompressed release point rather than the initial compressed position, omitting the spring compression distance Δy from the total elevation.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    Ee=12k(Δy)2  ⟹  Ee=12(1960)(0.350)2=120.05 JE_e = \frac{1}{2} k (\Delta y)^2 \implies E_e = \frac{1}{2} (1960) (0.350)^2 = 120.05\text{ J}

  2. Step 2

    12Mv2=Ee−MgΔy\frac{1}{2} M v^2 = E_e - M g \Delta y

  3. Step 3

    Mgh=Ee  ⟹  (2.50)(9.80)h=120.05  ⟹  24.5h=120.05M g h = E_e \implies (2.50)(9.80) h = 120.05 \implies 24.5 h = 120.05

  4. Step 4

    htotal=4.55 mh_{\text{total}} = 4.55\text{ m}

    Correct

    htotal=120.0524.5=4.90 mh_{\text{total}} = \frac{120.05}{24.5} = 4.90\text{ m}

    Solving 24.5h=120.0524.5 h = 120.05 gives h=4.90 mh = 4.90\text{ m}. You subtracted Δy=0.350 m\Delta y = 0.350\text{ m} to get 4.55 m4.55\text{ m}, which represents the height above the detachment point rather than the total elevation above the initial release point.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly calculated the initial elastic potential energy as 120.05 J120.05\text{ J}.

You set up valid conservation of energy equations for both the detachment point and the maximum height apex.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Reference Level Confusion

You subtracted the compression displacement Δy=0.350 m\Delta y = 0.350\text{ m} from the total height 4.90 m4.90\text{ m}, arriving at 4.55 m4.55\text{ m}.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You confused the height gained after detachment with the total elevation measured from the initial compressed release point. When you set the gravitational potential energy datum (y=0y = 0) at the release position, the height hh in Mgh=EeM g h = E_e already represents the full elevation above that release point.

REASONING PATH
Your ACEpath teacher’s suggested approach
Identify the Reference Level
  • Gravitational potential energy Ug=MgyU_g = M g y is always measured relative to a chosen reference level y=0y = 0.

  • Explicitly define your datum at the initial release position (y1=0y_1 = 0) so that the final position y2=htotaly_2 = h_{\text{total}} directly gives the elevation asked by the problem.

Distinguish Total Elevation from Free Flight
  • The total elevation above release is htotal=Δy+hflighth_{\text{total}} = \Delta y + h_{\text{flight}}, where hflighth_{\text{flight}} is the height gained above detachment.

  • If you solve Mgh=EeM g h = E_e directly from the release position, hh already includes Δy\Delta y; do not subtract Δy\Delta y at the end.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Solve 24.5h=120.0524.5 h = 120.05 directly for hh: h=120.0524.5=4.90 mh = \frac{120.05}{24.5} = 4.90\text{ m}.

  2. Recall that the gravitational reference level was chosen at the compressed release point (y=0y = 0).

  3. Conclude that htotal=4.90 mh_{\text{total}} = 4.90\text{ m} without subtracting Δy\Delta y.

Final answer

htotal=4.90 mh_{\text{total}} = 4.90\text{ m}

NEXT STEPS
Final Takeaways from Your Teacher
  • Always write down your choice of reference level (y=0y = 0) before setting up mechanical energy equations.

  • Double-check whether the problem asks for height above the release point or height above the uncompressed detachment point.

OverviewACEpath Teacher's Diagnosis

03 The student omits the factor of 1/2 in the formula for elastic potential energy, using E_e = k * (Δy)².

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    Ee=k(Δy)2  ⟹  Ee=(1960)(0.350)2=240.1 JE_e = k(\Delta y)^2 \implies E_e = (1960)(0.350)^2 = 240.1\text{ J}

    Correct

    Us=12k(Δy)2=12(1960)(0.350)2=120.05 JU_s = \frac{1}{2}k(\Delta y)^2 = \frac{1}{2}(1960)(0.350)^2 = 120.05\text{ J}

    You used Ee=k(Δy)2E_e = k(\Delta y)^2, missing the factor of 12\frac{1}{2}. Because the restoring force of an ideal spring varies linearly with displacement from 00 to kΔyk\Delta y, the work done storing energy is the average force times displacement, which gives Us=12k(Δy)2U_s = \frac{1}{2}k(\Delta y)^2.

  2. Step 2

    Mghtotal=Ee  ⟹  (2.50)(9.80)htotal=240.1  ⟹  24.5htotal=240.1M g h_{\text{total}} = E_e \implies (2.50)(9.80)h_{\text{total}} = 240.1 \implies 24.5 h_{\text{total}} = 240.1

    Correct

    Mghtotal=Us  ⟹  (2.50)(9.80)htotal=120.05  ⟹  24.5htotal=120.05M g h_{\text{total}} = U_s \implies (2.50)(9.80)h_{\text{total}} = 120.05 \implies 24.5 h_{\text{total}} = 120.05

    Your setup equating gravitational potential energy at the peak to initial elastic potential energy is conceptually sound, but it inherits the doubled energy value from the previous step.

  3. Step 3

    htotal=9.80 mh_{\text{total}} = 9.80\text{ m}

    Correct

    htotal=120.0524.5=4.90 mh_{\text{total}} = \frac{120.05}{24.5} = 4.90\text{ m}

    You solved your linear equation correctly, but the resulting height is off by a factor of 2 due to the initial formula slip.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified that mechanical energy is conserved between the release point and the highest elevation.

You selected a convenient reference level at the bottom and set the final gravitational potential energy equal to the initial stored elastic energy.

You carried out the arithmetic and solved for htotalh_{\text{total}} cleanly without calculation slips.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Missing $\frac{1}{2}$ in Elastic Potential Energy

You wrote Ee=k(Δy)2E_e = k(\Delta y)^2 instead of Ee=12k(Δy)2E_e = \frac{1}{2}k(\Delta y)^2.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You may have conflated the formula for spring force (F=kΔyF = k\Delta y) or overlooked the integration factor that yields the average force 12Fmax\frac{1}{2}F_{\text{max}} when calculating potential energy from Hooke's Law.

REASONING PATH
Your ACEpath teacher’s suggested approach
Spring Force vs. Spring Energy
  • Force is F=kxF = kx, whereas potential energy is Us=∫0xkx′ dx′=12kx2U_s = \int_0^x kx'\,dx' = \frac{1}{2}kx^2.

  • Always check units and integration factors: quadratic energy terms associated with linear restoring forces carry a coefficient of 12\frac{1}{2}.

Dimensional and Work Analogy
  • Work equals average force times distance: W=Fˉx=(0+kx2)x=12kx2W = \bar{F}x = \left(\frac{0 + kx}{2}\right)x = \frac{1}{2}kx^2.

  • Before evaluating numerical values, pause to write out the full algebraic expression with the 12\frac{1}{2} explicitly visible.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Calculate the correct initial elastic potential energy: Us=12k(Δy)2=12(1960 N/m)(0.350 m)2=120.05 JU_s = \frac{1}{2}k(\Delta y)^2 = \frac{1}{2}(1960\text{ N/m})(0.350\text{ m})^2 = 120.05\text{ J}.

  2. Equate the total initial energy to gravitational potential energy at the peak: Mghtotal=Us  ⟹  (2.50 kg)(9.80 m/s2)htotal=120.05 JM g h_{\text{total}} = U_s \implies (2.50\text{ kg})(9.80\text{ m/s}^2)h_{\text{total}} = 120.05\text{ J}.

  3. Simplify the product: 24.5 N⋅htotal=120.05 J24.5\text{ N} \cdot h_{\text{total}} = 120.05\text{ J}.

  4. Solve for the maximum height: htotal=120.0524.5=4.90 mh_{\text{total}} = \frac{120.05}{24.5} = 4.90\text{ m}.

Final answer

htotal=4.90 mh_{\text{total}} = 4.90\text{ m}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the work-energy theorem derivation for springs to solidify why the factor of 12\frac{1}{2} is required.

  • Practice matching quadratic energy forms: kinetic energy 12mv2\frac{1}{2}mv^2, rotational kinetic energy 12Iω2\frac{1}{2}I\omega^2, and elastic potential energy 12kx2\frac{1}{2}kx^2.

  • Solve follow-up projectile problems using algebraic isolation before plugging in numbers to catch missing coefficients early.

Lock it in

Similar question

01

A vertical spring with spring constant k=800 N/mk = 800\text{ N/m} is compressed downward by 0.20 m0.20\text{ m}. A 1.0 kg1.0\text{ kg} ball is placed on the spring and released from rest. Neglecting friction and drag, what is the maximum height reached by the ball above its release point? (Use g=9.8 m/s2g = 9.8\text{ m/s}^2)

Answer

h=1.63 mh = 1.63\text{ m}. Initial elastic energy: Us=12(800)(0.20)2=16 JU_s = \frac{1}{2}(800)(0.20)^2 = 16\text{ J}. Equating to gravitational potential energy at apex: mgh=16 J  ⟹  (1.0)(9.8)h=16  ⟹  h≈1.63 mm g h = 16\text{ J} \implies (1.0)(9.8)h = 16 \implies h \approx 1.63\text{ m}.

02

A toy launcher uses a spring with k=500 N/mk = 500\text{ N/m} compressed by 0.12 m0.12\text{ m}. It launches a 0.050 kg0.050\text{ kg} dart vertically. Find: (a) the dart's speed as the spring returns to equilibrium, and (b) the maximum total height above the compressed release point. (Use g=9.80 m/s2g = 9.80\text{ m/s}^2)

Answer

(a) v≈11.8 m/sv \approx 11.8\text{ m/s}; (b) htotal≈7.35 mh_{\text{total}} \approx 7.35\text{ m}. Total initial stored energy is Us=12(500)(0.12)2=3.60 JU_s = \frac{1}{2}(500)(0.12)^2 = 3.60\text{ J}. At equilibrium (y=0.12 my = 0.12\text{ m}): Us=mgy+12mv2  ⟹  3.60=(0.050)(9.80)(0.12)+12(0.050)v2  ⟹  3.60=0.0588+0.025v2  ⟹  v≈11.8 m/sU_s = m g y + \frac{1}{2}m v^2 \implies 3.60 = (0.050)(9.80)(0.12) + \frac{1}{2}(0.050)v^2 \implies 3.60 = 0.0588 + 0.025 v^2 \implies v \approx 11.8\text{ m/s}. At the peak: mghtotal=3.60 J  ⟹  htotal=3.60(0.050)(9.80)≈7.35 mm g h_{\text{total}} = 3.60\text{ J} \implies h_{\text{total}} = \frac{3.60}{(0.050)(9.80)} \approx 7.35\text{ m}.

03

A block of mass m=2.0 kgm = 2.0\text{ kg} is dropped from a height H=1.5 mH = 1.5\text{ m} above an uncompressed vertical spring of force constant k=1600 N/mk = 1600\text{ N/m}. Determine the maximum downward compression xx of the spring when the block comes momentarily to rest. (Use g=9.8 m/s2g = 9.8\text{ m/s}^2)

Answer

x≈0.205 mx \approx 0.205\text{ m}. Take the lowest point (maximum compression) as the gravitational potential energy reference y=0y = 0. Total vertical fall is H+xH + x. Energy conservation: mg(H+x)=12kx2  ⟹  2.0(9.8)(1.5+x)=800x2  ⟹  800x2−19.6x−29.4=0m g (H + x) = \frac{1}{2}kx^2 \implies 2.0(9.8)(1.5 + x) = 800 x^2 \implies 800 x^2 - 19.6 x - 29.4 = 0. Using the quadratic formula yields x=19.6+19.62−4(800)(−29.4)1600≈0.205 mx = \frac{19.6 + \sqrt{19.6^2 - 4(800)(-29.4)}}{1600} \approx 0.205\text{ m}.

Loading workspace…