Resources

A warehouse operator compares two lifting methods for an identical load of weight W=1200 NW = 1200\text{ N} raised through a vertical height h=2.50 mh = 2.50\text{ m}: Method A uses a single movable pulley system with an Ideal Mechanical Advantage (IMA\text{IMA}) of 22 and a total cable friction of fA=60.0 Nf_A = 60.0\text{ N}; Method B adds two more pulleys to achieve an IMA\text{IMA} of 44, but the additional sheaves and bearings increase total friction to fB=140 Nf_B = 140\text{ N}. A novice student assumes that because Method B reduces the required pulling effort force, it must also be more mechanically efficient. Evaluate this claim quantitatively by calculating the actual mechanical efficiency ηA\eta_A of System A and ηB\eta_B of System B.

Answer and steps

Final answer

ηA=90.9%\eta_A = 90.9\%, ηB=68.2%\eta_B = 68.2\%; the student's assumption is incorrect because the additional friction and greater displacement of the effort cable significantly increase wasted non-conservative work, lowering efficiency.

Steps

01

Useful Work Output (WoutW_{\text{out}})

The useful work output is the work required to raise the load against gravity, independent of the mechanism used:

Wout=W⋅hW_{\text{out}} = W \cdot h

Wout=(1200 N)(2.50 m)=3000 JW_{\text{out}} = (1200\text{ N})(2.50\text{ m}) = 3000\text{ J}


02

Efficiency of System A (ηA\eta_A)

For a pulley system with an Ideal Mechanical Advantage (IMA\text{IMA}), the displacement of the effort cable dind_{\text{in}} is related to the load height hh by:

din,A=IMAA⋅h=2⋅2.50 m=5.00 md_{\text{in}, A} = \text{IMA}_A \cdot h = 2 \cdot 2.50\text{ m} = 5.00\text{ m}

In the ideal (frictionless) case, the required pulling force is:

Fideal,A=WIMAA=1200 N2=600 NF_{\text{ideal}, A} = \frac{W}{\text{IMA}_A} = \frac{1200\text{ N}}{2} = 600\text{ N}

Accounting for the opposing frictional resistance fA=60.0 Nf_A = 60.0\text{ N}, the actual input effort force is:

Fin,A=Fideal,A+fA=600 N+60.0 N=660 NF_{\text{in}, A} = F_{\text{ideal}, A} + f_A = 600\text{ N} + 60.0\text{ N} = 660\text{ N}

The total work input is:

Win,A=Fin,A⋅din,A=(660 N)(5.00 m)=3300 JW_{\text{in}, A} = F_{\text{in}, A} \cdot d_{\text{in}, A} = (660\text{ N})(5.00\text{ m}) = 3300\text{ J}

The mechanical efficiency of System A is:

ηA=WoutWin,A=3000 J3300 J=1011≈0.909=90.9%\eta_A = \frac{W_{\text{out}}}{W_{\text{in}, A}} = \frac{3000\text{ J}}{3300\text{ J}} = \frac{10}{11} \approx 0.909 = 90.9\%


03

Efficiency of System B (ηB\eta_B)

For System B, with IMAB=4\text{IMA}_B = 4:

din,B=IMAB⋅h=4⋅2.50 m=10.0 md_{\text{in}, B} = \text{IMA}_B \cdot h = 4 \cdot 2.50\text{ m} = 10.0\text{ m}

The ideal pulling force is:

Fideal,B=WIMAB=1200 N4=300 NF_{\text{ideal}, B} = \frac{W}{\text{IMA}_B} = \frac{1200\text{ N}}{4} = 300\text{ N}

With friction fB=140 Nf_B = 140\text{ N}, the actual input effort force is:

Fin,B=Fideal,B+fB=300 N+140 N=440 NF_{\text{in}, B} = F_{\text{ideal}, B} + f_B = 300\text{ N} + 140\text{ N} = 440\text{ N}

The total work input is:

Win,B=Fin,B⋅din,B=(440 N)(10.0 m)=4400 JW_{\text{in}, B} = F_{\text{in}, B} \cdot d_{\text{in}, B} = (440\text{ N})(10.0\text{ m}) = 4400\text{ J}

The mechanical efficiency of System B is:

ηB=WoutWin,B=3000 J4400 J=1522≈0.682=68.2%\eta_B = \frac{W_{\text{out}}}{W_{\text{in}, B}} = \frac{3000\text{ J}}{4400\text{ J}} = \frac{15}{22} \approx 0.682 = 68.2\%


04

Evaluating the Student's Claim

  • Common Pitfall: Conflating mechanical advantage with mechanical efficiency. A higher IMA\text{IMA} reduces the required applied force (440 N<660 N440\text{ N} < 660\text{ N}), making the object easier to pull by hand. However, efficiency measures the percentage of input energy converted into useful output work.
  • Because System B requires pulling the rope over twice the distance (10.0 m10.0\text{ m} vs. 5.00 m5.00\text{ m}), the non-conservative work done against friction increases dramatically: Wfriction,A=fA⋅din,A=(60.0 N)(5.00 m)=300 JW_{\text{friction}, A} = f_A \cdot d_{\text{in}, A} = (60.0\text{ N})(5.00\text{ m}) = 300\text{ J} Wfriction,B=fB⋅din,B=(140 N)(10.0 m)=1400 JW_{\text{friction}, B} = f_B \cdot d_{\text{in}, B} = (140\text{ N})(10.0\text{ m}) = 1400\text{ J}
  • Thus, the student's assumption is incorrect: System B is significantly less efficient (68.2%68.2\%) than System A (90.9%90.9\%).

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student subtracts the friction force from the ideal effort instead of adding it, assuming friction aids the pull rather than opposing it.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    Wout=1200⋅2.50=3000 JW_{\text{out}} = 1200 \cdot 2.50 = 3000\text{ J}

  2. Step 2

    Fideal,A=12002=600 N  ⟹  Factual,A=600−60.0=540 NF_{\text{ideal}, A} = \frac{1200}{2} = 600\text{ N} \implies F_{\text{actual}, A} = 600 - 60.0 = 540\text{ N}

    Correct

    Fin,A=Fideal,A+fA=600 N+60.0 N=660 NF_{\text{in}, A} = F_{\text{ideal}, A} + f_A = 600\text{ N} + 60.0\text{ N} = 660\text{ N}

    You subtracted the friction force from the ideal force. Because friction resists the pulling motion, the actual input effort must overcome both the ideal load share and friction: Fin=Fideal+fF_{\text{in}} = F_{\text{ideal}} + f.

  3. Step 3

    Win,A=540⋅5.00=2700 J  ⟹  ηA=30002700=1.11=111%W_{\text{in}, A} = 540 \cdot 5.00 = 2700\text{ J} \implies \eta_A = \frac{3000}{2700} = 1.11 = 111\%

    Correct

    Win,A=(660 N)(5.00 m)=3300 J  ⟹  ηA=3000 J3300 J≈90.9%W_{\text{in}, A} = (660\text{ N})(5.00\text{ m}) = 3300\text{ J} \implies \eta_A = \frac{3000\text{ J}}{3300\text{ J}} \approx 90.9\%

    Your formulas for work input and efficiency were applied properly, but your result was affected by the underestimated effort force, yielding an efficiency over 100%100\%, which violates conservation of energy.

  4. Step 4

    Fideal,B=12004=300 N  ⟹  Factual,B=300−140=160 NF_{\text{ideal}, B} = \frac{1200}{4} = 300\text{ N} \implies F_{\text{actual}, B} = 300 - 140 = 160\text{ N}

    Correct

    Fin,B=Fideal,B+fB=300 N+140 N=440 NF_{\text{in}, B} = F_{\text{ideal}, B} + f_B = 300\text{ N} + 140\text{ N} = 440\text{ N}

    You repeated the subtraction of friction for System B. The actual effort needed is 300 N+140 N=440 N300\text{ N} + 140\text{ N} = 440\text{ N}.

  5. Step 5

    Win,B=160⋅10.0=1600 J  ⟹  ηB=30001600=1.88=188%W_{\text{in}, B} = 160 \cdot 10.0 = 1600\text{ J} \implies \eta_B = \frac{3000}{1600} = 1.88 = 188\%

    Correct

    Win,B=(440 N)(10.0 m)=4400 J  ⟹  ηB=3000 J4400 J≈68.2%W_{\text{in}, B} = (440\text{ N})(10.0\text{ m}) = 4400\text{ J} \implies \eta_B = \frac{3000\text{ J}}{4400\text{ J}} \approx 68.2\%

    Your calculation of input work and efficiency followed the correct structure, but the value propagated from the incorrect force.

  6. Step 6

    Claim is supported because ηB>ηA.\text{Claim is supported because } \eta_B > \eta_A.

    Correct

    The claim is incorrect because ηA=90.9%>ηB=68.2%.\text{The claim is incorrect because } \eta_A = 90.9\% > \eta_B = 68.2\%.

    Because your calculated efficiencies were reversed due to the friction sign error, your conclusion about the operator's claim was also reversed.

WHAT YOU DID WELL
Compliments from Your Teacher

You calculated the gravitational potential energy gained by the load correctly as 3000 J3000\text{ J}.

You correctly used the ideal mechanical advantage to find the ideal effort force and the input cable displacement for both systems.

You set up the efficiency ratio as useful work output divided by work input.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Sign error on non-conservative resistive forces

You treated friction as an assisting force that reduces input effort rather than an opposing force that increases it.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Conflating load-reducing mechanical advantage with frictional losses. In real machines, non-conservative forces such as friction dissipate energy as thermal energy, meaning the operator must perform extra work (Win=Wout+WfrictionW_{\text{in}} = W_{\text{out}} + W_{\text{friction}}), so the applied force must exceed the ideal force: Factual=Fideal+fF_{\text{actual}} = F_{\text{ideal}} + f.

REASONING PATH
Your ACEpath teacher’s suggested approach
Sanity Check Efficiency Bounds
  • For any passive machine, mechanical efficiency must satisfy η≤100%\eta \le 100\% (Win≥WoutW_{\text{in}} \ge W_{\text{out}}) due to the first and second laws of thermodynamics.

  • Whenever you compute an efficiency greater than 100%100\%, immediately re-examine your input force and work input to verify whether friction was added or subtracted.

Accounting for Friction in Machines
  • Friction always opposes the direction of cable motion, adding to the effort needed: Fin=WIMA+fF_{\text{in}} = \frac{W}{\text{IMA}} + f.

  • Sum the ideal effort and the frictional resistance when determining the actual pulling force required.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Compute the actual input force for System A: Fin,A=Fideal,A+fA=600 N+60.0 N=660 NF_{\text{in}, A} = F_{\text{ideal}, A} + f_A = 600\text{ N} + 60.0\text{ N} = 660\text{ N}.

  2. Calculate total work input for System A: Win,A=Fin,A⋅din,A=(660 N)(5.00 m)=3300 JW_{\text{in}, A} = F_{\text{in}, A} \cdot d_{\text{in}, A} = (660\text{ N})(5.00\text{ m}) = 3300\text{ J}.

  3. Calculate actual efficiency for System A: ηA=WoutWin,A=3000 J3300 J=1011≈90.9%\eta_A = \frac{W_{\text{out}}}{W_{\text{in}, A}} = \frac{3000\text{ J}}{3300\text{ J}} = \frac{10}{11} \approx 90.9\%.

  4. Compute the actual input force for System B: Fin,B=Fideal,B+fB=300 N+140 N=440 NF_{\text{in}, B} = F_{\text{ideal}, B} + f_B = 300\text{ N} + 140\text{ N} = 440\text{ N}.

  5. Calculate total work input for System B: Win,B=Fin,B⋅din,B=(440 N)(10.0 m)=4400 JW_{\text{in}, B} = F_{\text{in}, B} \cdot d_{\text{in}, B} = (440\text{ N})(10.0\text{ m}) = 4400\text{ J}.

  6. Calculate actual efficiency for System B: ηB=WoutWin,B=3000 J4400 J=1522≈68.2%\eta_B = \frac{W_{\text{out}}}{W_{\text{in}, B}} = \frac{3000\text{ J}}{4400\text{ J}} = \frac{15}{22} \approx 68.2\%.

  7. Compare efficiencies: ηA(90.9%)>ηB(68.2%)\eta_A (90.9\%) > \eta_B (68.2\%), proving the student's claim is false.

Final answer

ηA=90.9%\eta_A = 90.9\%, ηB=68.2%\eta_B = 68.2\%; the claim is unsupported because System B is less efficient.

NEXT STEPS
Final Takeaways from Your Teacher
  • Review free-body diagrams of pulley sheaves to clearly see that bearing friction opposes the rotation driven by the pulling force.

  • Check that work input is always greater than work output (Win=Wout+WlossW_{\text{in}} = W_{\text{out}} + W_{\text{loss}}) before completing efficiency problems.

OverviewACEpath Teacher's Diagnosis

02 The student calculates efficiency as the ratio of load height to effort displacement, which is merely 1/IMA and neglects friction entirely.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    din,A=2⋅2.50=5.00 m  ⟹  din,B=4⋅2.50=10.0 md_{\text{in}, A} = 2 \cdot 2.50 = 5.00\text{ m} \implies d_{\text{in}, B} = 4 \cdot 2.50 = 10.0\text{ m}

  2. Step 2

    ηA=hdin,A=2.505.00=0.50=50%\eta_A = \frac{h}{d_{\text{in}, A}} = \frac{2.50}{5.00} = 0.50 = 50\%

    Correct

    ηA=WoutWin,A=W⋅h(Fideal,A+fA)⋅din,A=3000 J(600 N+60.0 N)(5.00 m)=3000 J3300 J≈90.9%\eta_A = \frac{W_{\text{out}}}{W_{\text{in}, A}} = \frac{W \cdot h}{(F_{\text{ideal}, A} + f_A) \cdot d_{\text{in}, A}} = \frac{3000\text{ J}}{(600\text{ N} + 60.0\text{ N})(5.00\text{ m})} = \frac{3000\text{ J}}{3300\text{ J}} \approx 90.9\%

    You set efficiency equal to the ratio of load height to effort displacement hdin\frac{h}{d_{\text{in}}}, which is merely 1IMA\frac{1}{\text{IMA}}. Mechanical efficiency is the ratio of useful work output to total work input, η=WoutWin\eta = \frac{W_{\text{out}}}{W_{\text{in}}}, which requires accounting for the friction force fAf_A.

  3. Step 3

    ηB=hdin,B=2.5010.0=0.25=25%\eta_B = \frac{h}{d_{\text{in}, B}} = \frac{2.50}{10.0} = 0.25 = 25\%

    Correct

    ηB=WoutWin,B=W⋅h(Fideal,B+fB)⋅din,B=3000 J(300 N+140 N)(10.0 m)=3000 J4400 J≈68.2%\eta_B = \frac{W_{\text{out}}}{W_{\text{in}, B}} = \frac{W \cdot h}{(F_{\text{ideal}, B} + f_B) \cdot d_{\text{in}, B}} = \frac{3000\text{ J}}{(300\text{ N} + 140\text{ N})(10.0\text{ m})} = \frac{3000\text{ J}}{4400\text{ J}} \approx 68.2\%

    You repeated the same formula error for System B, omitting the actual input force Fin,B=300 N+140 N=440 NF_{\text{in}, B} = 300\text{ N} + 140\text{ N} = 440\text{ N} and calculating 1IMAB=25%\frac{1}{\text{IMA}_B} = 25\% instead of the actual energy efficiency.

  4. Step 4

    Claim is incorrect because ηA>ηB.\text{Claim is incorrect because } \eta_A > \eta_B.

    Correct

    The claim is incorrect because ηA=90.9%>ηB=68.2%\eta_A = 90.9\% > \eta_B = 68.2\%; pulling the rope through a greater distance with higher friction wastes more non-conservative work.

    Your final qualitative conclusion is correct, but the values you used to justify it were derived from an incorrect definition of mechanical efficiency.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly related the load height and the ideal mechanical advantage to find the cable displacement for both systems.

You recognized that a higher mechanical advantage does not necessarily mean higher efficiency.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Conflating Mechanical Advantage with Mechanical Efficiency

You used the kinematic ratio hdin\frac{h}{d_{\text{in}}} as efficiency instead of calculating work input and work output.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You confused the geometric velocity ratio (or 1IMA\frac{1}{\text{IMA}}) with mechanical efficiency η\eta. Efficiency always represents an energy ratio WoutWin=AMAIMA\frac{W_{\text{out}}}{W_{\text{in}}} = \frac{\text{AMA}}{\text{IMA}}, which requires evaluating the actual input force needed to overcome both the ideal load and friction.

REASONING PATH
Your ACEpath teacher’s suggested approach
Definition of Mechanical Efficiency
  • Mechanical efficiency is strictly the ratio of useful work output to total work input: η=WoutWin=Fload⋅dloadFeffort⋅deffort=AMAIMA\eta = \frac{W_{\text{out}}}{W_{\text{in}}} = \frac{F_{\text{load}} \cdot d_{\text{load}}}{F_{\text{effort}} \cdot d_{\text{effort}}} = \frac{\text{AMA}}{\text{IMA}}.

  • Always compute WoutW_{\text{out}} and WinW_{\text{in}} in Joules (or find the actual effort force Fin=Fideal+fF_{\text{in}} = F_{\text{ideal}} + f) before calculating efficiency.

Distinguishing IMA from Efficiency
  • IMA=dindout\text{IMA} = \frac{d_{\text{in}}}{d_{\text{out}}} is purely determined by geometry and has nothing to do with energy loss; an ideal machine with no friction has η=100%\eta = 100\% regardless of its IMA\text{IMA}.

  • Check your formula: if your efficiency expression contains only distances, you are calculating 1IMA\frac{1}{\text{IMA}}, not efficiency.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Calculate useful work output: Wout=W⋅h=(1200 N)(2.50 m)=3000 JW_{\text{out}} = W \cdot h = (1200\text{ N})(2.50\text{ m}) = 3000\text{ J}.

  2. Find the actual input force for System A: Fin,A=WIMAA+fA=1200 N2+60.0 N=660 NF_{\text{in}, A} = \frac{W}{\text{IMA}_A} + f_A = \frac{1200\text{ N}}{2} + 60.0\text{ N} = 660\text{ N}.

  3. Compute the work input for System A: Win,A=Fin,A⋅din,A=(660 N)(5.00 m)=3300 JW_{\text{in}, A} = F_{\text{in}, A} \cdot d_{\text{in}, A} = (660\text{ N})(5.00\text{ m}) = 3300\text{ J}.

  4. Calculate ηA=3000 J3300 J=1011≈90.9%\eta_A = \frac{3000\text{ J}}{3300\text{ J}} = \frac{10}{11} \approx 90.9\%.

  5. Find the actual input force for System B: Fin,B=WIMAB+fB=1200 N4+140 N=440 NF_{\text{in}, B} = \frac{W}{\text{IMA}_B} + f_B = \frac{1200\text{ N}}{4} + 140\text{ N} = 440\text{ N}.

  6. Compute the work input for System B: Win,B=Fin,B⋅din,B=(440 N)(10.0 m)=4400 JW_{\text{in}, B} = F_{\text{in}, B} \cdot d_{\text{in}, B} = (440\text{ N})(10.0\text{ m}) = 4400\text{ J}.

  7. Calculate ηB=3000 J4400 J=1522≈68.2%\eta_B = \frac{3000\text{ J}}{4400\text{ J}} = \frac{15}{22} \approx 68.2\%.

  8. Evaluate the claim: since ηA(90.9%)>ηB(68.2%)\eta_A (90.9\%) > \eta_B (68.2\%), the student's claim is quantitatively disproven.

Final answer

ηA=90.9%\eta_A = 90.9\%, ηB=68.2%\eta_B = 68.2\%; the claim is incorrect.

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice expressing efficiency as both WoutWin\frac{W_{\text{out}}}{W_{\text{in}}} and AMAIMA\frac{\text{AMA}}{\text{IMA}} to avoid substituting pure displacement ratios for efficiency.

  • Solve problems where machines have different mechanical advantages and internal friction values to reinforce how extra moving parts can reduce overall efficiency.

OverviewACEpath Teacher's Diagnosis

03 The student omits the displacement multiplier for work done against friction, adding friction force directly to useful work rather than multiplying it by effort displacement.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    Wout=1200⋅2.50=3000 JW_{\text{out}} = 1200 \cdot 2.50 = 3000\text{ J}

  2. Step 2

    Win,A=Wout+fA=3000+60.0=3060 JW_{\text{in}, A} = W_{\text{out}} + f_A = 3000 + 60.0 = 3060\text{ J}

    Correct

    Win,A=Wout+fA⋅din,A=3000 J+(60.0 N)(5.00 m)=3300 JW_{\text{in}, A} = W_{\text{out}} + f_A \cdot d_{\text{in}, A} = 3000\text{ J} + (60.0\text{ N})(5.00\text{ m}) = 3300\text{ J}

    You added a force in newtons (fA=60.0 Nf_A = 60.0\text{ N}) directly to an energy quantity in joules (3000 J3000\text{ J}). To find work done against friction, multiply the frictional resistance by the effort displacement: din,A=IMAA⋅h=2⋅2.50 m=5.00 md_{\text{in}, A} = \text{IMA}_A \cdot h = 2 \cdot 2.50\text{ m} = 5.00\text{ m}, giving Wfriction,A=300 JW_{\text{friction}, A} = 300\text{ J}.

  3. Step 3

    etaA=30003060=0.980=98.0%\text{eta}_A = \frac{3000}{3060} = 0.980 = 98.0\%

    Correct

    ηA=WoutWin,A=3000 J3300 J≈90.9%\eta_A = \frac{W_{\text{out}}}{W_{\text{in}, A}} = \frac{3000\text{ J}}{3300\text{ J}} \approx 90.9\%

    Your efficiency formula is conceptually correct, but the result is inaccurate due to the understated input work from Step 2.

  4. Step 4

    Win,B=Wout+fB=3000+140=3140 JW_{\text{in}, B} = W_{\text{out}} + f_B = 3000 + 140 = 3140\text{ J}

    Correct

    Win,B=Wout+fB⋅din,B=3000 J+(140 N)(10.0 m)=4400 JW_{\text{in}, B} = W_{\text{out}} + f_B \cdot d_{\text{in}, B} = 3000\text{ J} + (140\text{ N})(10.0\text{ m}) = 4400\text{ J}

    You repeated the same dimensional error by omitting the displacement factor din,B=IMAB⋅h=4⋅2.50 m=10.0 md_{\text{in}, B} = \text{IMA}_B \cdot h = 4 \cdot 2.50\text{ m} = 10.0\text{ m}. The actual work done against friction is Wfriction,B=(140 N)(10.0 m)=1400 JW_{\text{friction}, B} = (140\text{ N})(10.0\text{ m}) = 1400\text{ J}.

  5. Step 5

    etaB=30003140=0.955=95.5%\text{eta}_B = \frac{3000}{3140} = 0.955 = 95.5\%

    Correct

    ηB=WoutWin,B=3000 J4400 J≈68.2%\eta_B = \frac{W_{\text{out}}}{W_{\text{in}, B}} = \frac{3000\text{ J}}{4400\text{ J}} \approx 68.2\%

    This calculation correctly evaluates WoutWin\frac{W_{\text{out}}}{W_{\text{in}}}, but the value is affected by the incorrect input work in Step 4.

  6. Step 6

    Claim is incorrect because etaA>etaB.\text{Claim is incorrect because } \text{eta}_A > \text{eta}_B.

    Correct

    The claim is incorrect because ηA=90.9%>ηB=68.2%\eta_A = 90.9\% > \eta_B = 68.2\%.

    Your qualitative conclusion happens to agree with the correct answer, but your quantitative efficiencies were derived from dimensionally inconsistent input work expressions.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly computed the useful work output as Wout=3000 JW_{\text{out}} = 3000\text{ J}.

You correctly applied the definition of mechanical efficiency as η=WoutWin\eta = \frac{W_{\text{out}}}{W_{\text{in}}}.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Dimensional Inconsistency / Omitted Displacement Multiplier

You treated friction force as an amount of wasted energy, writing Win=Wout+fW_{\text{in}} = W_{\text{out}} + f.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You overlooked that work is the product of force and displacement (W=F⋅dW = F \cdot d), adding a force in newtons directly to work in joules and ignoring that higher IMA systems pull the cable over a proportionally longer distance.

REASONING PATH
Your ACEpath teacher’s suggested approach
Dimensional Consistency Check
  • Every additive term in an energy equation must carry units of energy (Joules, N⋅m\text{N}\cdot\text{m}), never force (Newtons).

  • Always multiply non-conservative friction forces by the distance over which they act: Wfriction=f⋅dinW_{\text{friction}} = f \cdot d_{\text{in}}.

Effort Displacement via IMA
  • For an ideal pulley or simple machine, effort displacement is din=IMA⋅hd_{\text{in}} = \text{IMA} \cdot h.

  • Calculate dind_{\text{in}} first whenever computing input work or energy dissipated by friction along the input line.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Find input displacement for System A: din,A=IMAA⋅h=2⋅2.50 m=5.00 md_{\text{in}, A} = \text{IMA}_A \cdot h = 2 \cdot 2.50\text{ m} = 5.00\text{ m}.

  2. Calculate actual input work for System A: Win,A=Wout+fA⋅din,A=3000 J+(60.0 N)(5.00 m)=3300 JW_{\text{in}, A} = W_{\text{out}} + f_A \cdot d_{\text{in}, A} = 3000\text{ J} + (60.0\text{ N})(5.00\text{ m}) = 3300\text{ J}.

  3. Compute efficiency for System A: ηA=3000 J3300 J=1011≈90.9%\eta_A = \frac{3000\text{ J}}{3300\text{ J}} = \frac{10}{11} \approx 90.9\%.

  4. Find input displacement for System B: din,B=IMAB⋅h=4⋅2.50 m=10.0 md_{\text{in}, B} = \text{IMA}_B \cdot h = 4 \cdot 2.50\text{ m} = 10.0\text{ m}.

  5. Calculate actual input work for System B: Win,B=Wout+fB⋅din,B=3000 J+(140 N)(10.0 m)=4400 JW_{\text{in}, B} = W_{\text{out}} + f_B \cdot d_{\text{in}, B} = 3000\text{ J} + (140\text{ N})(10.0\text{ m}) = 4400\text{ J}.

  6. Compute efficiency for System B: ηB=3000 J4400 J=1522≈68.2%\eta_B = \frac{3000\text{ J}}{4400\text{ J}} = \frac{15}{22} \approx 68.2\%.

Final answer

ηA=90.9%\eta_A = 90.9\%, ηB=68.2%\eta_B = 68.2\%; the novice's claim is incorrect because System B requires pulling cable through twice the distance, multiplying the energy lost to friction and lowering overall efficiency.

NEXT STEPS
Final Takeaways from Your Teacher
  • Check units of every term before adding them: verify that terms have units of J\text{J} rather than N\text{N}.

  • Practice separating Ideal Mechanical Advantage (which trades force for distance) from Mechanical Efficiency (which compares useful energy to total input energy).

Lock it in

Similar question

01

A ramp has an ideal mechanical advantage of IMA=3.0\text{IMA} = 3.0. To slide a 600 N600\text{ N} crate to the top, friction between the crate and ramp is 50 N50\text{ N}. Find the actual pushing force required and the mechanical efficiency of the ramp.

Answer

Fin=250 NF_{\text{in}} = 250\text{ N}, η=80.0%\eta = 80.0\%. Key steps: Fideal=600 N3.0=200 NF_{\text{ideal}} = \frac{600\text{ N}}{3.0} = 200\text{ N}. With friction opposing motion, Fin=200 N+50 N=250 NF_{\text{in}} = 200\text{ N} + 50\text{ N} = 250\text{ N}. Efficiency is η=FidealFin=200 N250 N=80.0%\eta = \frac{F_{\text{ideal}}}{F_{\text{in}}} = \frac{200\text{ N}}{250\text{ N}} = 80.0\%.

02

A hydraulic lift with IMA=20\text{IMA} = 20 lifts a 10,000 N10{,}000\text{ N} vehicle through a height of 1.8 m1.8\text{ m}. Due to seal friction, the actual input force applied is 625 N625\text{ N}. Calculate the friction force ff opposing the input piston and the mechanical efficiency of the lift.

Answer

f=125 Nf = 125\text{ N}, η=80.0%\eta = 80.0\%. Key steps: Ideal input force Fideal=10,000 N20=500 NF_{\text{ideal}} = \frac{10{,}000\text{ N}}{20} = 500\text{ N}. Frictional resistance is f=Fin−Fideal=625 N−500 N=125 Nf = F_{\text{in}} - F_{\text{ideal}} = 625\text{ N} - 500\text{ N} = 125\text{ N}. Efficiency is η=FidealFin=500 N625 N=80.0%\eta = \frac{F_{\text{ideal}}}{F_{\text{in}}} = \frac{500\text{ N}}{625\text{ N}} = 80.0\%.

03

A winch system has IMA=5.0\text{IMA} = 5.0. Raising an 800 N800\text{ N} load by 4.0 m4.0\text{ m} requires an actual effort of 220 N220\text{ N}. (a) Determine the energy lost to friction. (b) If an engineer redesigns the gears to increase IMA\text{IMA} to 8.08.0 but gear friction increases the required effort to 150 N150\text{ N}, does the efficiency improve or worsen?

Answer

(a) Wlost=1200 JW_{\text{lost}} = 1200\text{ J}; (b) Efficiency worsens from 72.7%72.7\% to 66.7%66.7\%. Key steps: Wout=(800 N)(4.0 m)=3200 JW_{\text{out}} = (800\text{ N})(4.0\text{ m}) = 3200\text{ J}. Original: din=5.0×4.0 m=20 md_{\text{in}} = 5.0 \times 4.0\text{ m} = 20\text{ m}, Win=(220 N)(20 m)=4400 JW_{\text{in}} = (220\text{ N})(20\text{ m}) = 4400\text{ J}, so Wlost=4400−3200=1200 JW_{\text{lost}} = 4400 - 3200 = 1200\text{ J}, η1=32004400≈72.7%\eta_1 = \frac{3200}{4400} \approx 72.7\%. Redesign: din=8.0×4.0 m=32 md_{\text{in}} = 8.0 \times 4.0\text{ m} = 32\text{ m}, Win=(150 N)(32 m)=4800 JW_{\text{in}} = (150\text{ N})(32\text{ m}) = 4800\text{ J}, η2=32004800≈66.7%\eta_2 = \frac{3200}{4800} \approx 66.7\%.

Loading workspace…