Resources
An engineering student constructs an asymmetrical dumbbell consisting of two small spherical weights joined by a thin carbon-fiber rod of length with negligible mass. One sphere has a known mass and is located at . By balancing the system on a sharp knife-edge, the student determines that the center of mass is located precisely at along the rod. Determine the mass of the second sphere positioned at .
Answer and steps
Final answer
Steps
Method 1: Center of Mass Definition
The center of mass for a system of point masses along a straight line is defined by:
Substitute the given values into the formula:
- at
Simplify the numerator:
Multiply both sides by :
Collect the terms involving on one side:
Solve for :
Alternative Method: Torque Balance (Principle of Moments)
When an object balances horizontally on a sharp pivot (knife-edge), the pivot is located at its center of gravity (which coincides with the center of mass in a uniform gravitational field). The net torque about the pivot must be zero:
Dividing both sides by the gravitational acceleration :
-
Determine the lever arm distances from the balance point ():
- Distance to mass :
- Distance to mass :
-
Substitute the values:
Common Pitfall: Be careful when identifying lever arm distances in torque calculations. Using the total rod length instead of the distance from the pivot for will result in an incorrect mass.
Typical errors
01 The student forgets that the denominator of the center-of-mass formula includes the total mass (m_1 + m_2) and instead divides only by m_2 or treats the formula as x_cm = (m_1*x_1 + m_2*x_2)/m_1.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
or
You inverted the lever arm distances. Mass is at , so its distance to the balance point is . Mass is at , so its distance to the balance point is . Multiplying cross-wise from gives .
- Step 3Correct
You substituted your numerical values and simplified consistently with your mismatched lever arm equation.
- Step 4Correct
Your final calculation followed from the swapped lever arms. A physical sanity check shows that because is beyond the midpoint (), must be larger than .
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly wrote down the standard formula for the center of mass of a two-body system.
You correctly evaluated the distance difference .
You performed the algebraic isolation and division accurately based on your equation.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou associated the remaining distance to the right end with the left mass , and the position coordinate with the right mass , reversing the inverse relationship between mass and lever arm in static equilibrium.
REASONING PATH
Your ACEpath teacher’s suggested approach- Distance to Pivot
In torque balance about the center of mass, each mass is multiplied by its own distance to the center of mass: , where and .
Always sketch the line segment and label and from the pivot point directly to each mass before writing the equation.
- Physical Sanity Check
The center of mass is always located closer to the heavier mass.
Check whether is past the midpoint: since , it is closer to , meaning must exceed .
CORRECTED PATH
ACEpath Teacher's DemonstrationWrite the torque balance about the center of mass:
Substitute the given values:
Simplify both sides:
Solve for :
02 The student inverts the lever arms in the torque balance equation, multiplying each mass by the distance to the opposite end or assigning the wrong distance from the pivot.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
The center of mass is a mass-weighted average of position, so the denominator must be the sum of the masses , not the geometric length .
- Step 2Correct
You solved your linear equation correctly, but your calculation was carried out on an incorrect denominator.
- Step 3Correct
Because the denominator used length rather than total mass, the resulting mass of the second sphere is incorrect.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly identified the coordinates and along the rod.
You substituted the known numerical values into the numerator correctly.
You performed each algebraic step accurately according to your written equation.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakenone
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing the center-of-mass weighting denominator (total mass ) with the spatial span or total length (). Notice that dividing the moment (units of ) by length (units of ) yields units of , whereas a center-of-mass coordinate must have units of meters.
REASONING PATH
Your ACEpath teacher’s suggested approach- Center of Mass Denominator Rule
The one-dimensional center of mass is defined as . The denominator is always the total mass , never the total length .
Before solving for an unknown mass, verify that the denominator is the sum of all masses so that the overall expression yields units of length.
- Dimensional Consistency Check
The units on both sides of a physical equation must match: .
Check that . If you place length in the denominator, you get , which signals a missing total mass term.
CORRECTED PATH
ACEpath Teacher's DemonstrationSet up the correct center-of-mass formula: .
Substitute the known values: .
Clear the denominator: .
Collect terms in : .
03 The student misidentifies the distance of the second mass from the center of mass as the total length L instead of L - x_cm when balancing torques about the knife-edge.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
When balancing torques about the knife-edge at , each lever arm must be measured relative to the pivot. Mass is located at , so its distance from the pivot is , not the full length .
- Step 2Correct
Your algebraic simplification and division were carried out correctly, but the result is incorrect due to the lever arm error in Step 1.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly recognized that the net torque about the balance point must equal zero.
You correctly identified that the distance from to the pivot is .
You solved the linear equation accurately based on your setup.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou substituted the position coordinate directly as the lever arm instead of subtracting the pivot coordinate .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing an absolute coordinate along a reference axis with a relative lever-arm distance measured from the pivot point.
REASONING PATH
Your ACEpath teacher’s suggested approach- Identify the Pivot and Distances
A lever arm for torque about a pivot at is always the relative distance , never the coordinate itself unless .
Always sketch the system, mark the pivot location, and explicitly write for every mass before setting up .
CORRECTED PATH
ACEpath Teacher's DemonstrationSet up torque balance about the knife-edge:
Substitute the given values:
Divide by :
Lock it in
In torque balance about the center of mass for two point masses on a line, what is the relationship between their masses and distances from the pivot?
, where each distance is measured directly from the center of mass to mass .
Similar question
A light rod of length connects a sphere at and a sphere of mass at . The system balances on a knife edge at . Calculate the mass .
Answer
. The lever arm for the first mass is , and for the second mass is . Balancing torques: .
Two point masses, located at and located at , rest on a horizontal axis. Find the coordinate of the center of mass.
Answer
. Using .
An asymmetrical bar of total length and negligible mass has masses at , at , and an unknown mass at . If the entire system balances at , find .
Answer
. Using torque equilibrium about the pivot at : counterclockwise torque from and must equal clockwise torque from . For : . For : . For : . Equating torques: .