Resources

In an experiment designed to calibrate a thermocouple against an insulated water calorimeter, students deliver electrical energy to a submerged resistor via a regulated DC power supply. An ammeter and voltmeter record current I=(2.40±0.05) AI = (2.40 \pm 0.05)\text{ A} and potential difference V=(12.0±0.2) VV = (12.0 \pm 0.2)\text{ V} delivered across a time interval Δt=(300.0±0.5) s\Delta t = (300.0 \pm 0.5)\text{ s}. The calorimeter contains mw=(0.250±0.002) kgm_w = (0.250 \pm 0.002)\text{ kg} of distilled water (cw=4186 J/(kg⋅∘C)c_w = 4186\text{ J}/(\text{kg}\cdot{^\circ}\text{C})), and the heat capacity of the calorimeter vessel is Ccal=(45.0±2.0) J/∘CC_{\text{cal}} = (45.0 \pm 2.0)\text{ J}/{^\circ}\text{C}. The observed temperature change is ΔT=(7.40±0.15)∘C\Delta T = (7.40 \pm 0.15){^\circ}\text{C}. Calculate: (a) the electrical energy input Ein=VIΔtE_{\text{in}} = V I \Delta t in joules, (b) the thermal energy absorbed Qabsorbed=(mwcw+Ccal)ΔTQ_{\text{absorbed}} = (m_w c_w + C_{\text{cal}})\Delta T in joules, and (c) the percentage heat loss to the ambient surroundings relative to EinE_{\text{in}} to three significant figures.

Answer and steps

Final answer

(a) Ein=8640 JE_{\text{in}} = 8640\text{ J}; (b) Qabsorbed=8080 JQ_{\text{absorbed}} = 8080\text{ J}; (c) Percentage heat loss =6.48%= 6.48\%

Steps

01

Calculate the Electrical Energy Input (EinE_{\text{in}})

Electrical energy supplied by a direct current source is given by the product of potential difference, current, and time:

Ein=V⋅I⋅ΔtE_{\text{in}} = V \cdot I \cdot \Delta t

Substitute the given central values:

Ein=(12.0 V)⋅(2.40 A)⋅(300.0 s)=8640 JE_{\text{in}} = (12.0\text{ V}) \cdot (2.40\text{ A}) \cdot (300.0\text{ s}) = 8640\text{ J}


02

Calculate the Thermal Energy Absorbed (QabsorbedQ_{\text{absorbed}})

The thermal energy absorbed by the system includes both the energy required to raise the temperature of the water and the energy absorbed by the calorimeter container:

Qabsorbed=(mwcw+Ccal)ΔTQ_{\text{absorbed}} = (m_w c_w + C_{\text{cal}})\Delta T

  1. Determine the heat capacity of the water: Cw=mwcw=(0.250 kg)⋅(4186 J/(kg⋅∘C))=1046.5 J/∘CC_w = m_w c_w = (0.250\text{ kg}) \cdot (4186\text{ J}/(\text{kg}\cdot{^\circ}\text{C})) = 1046.5\text{ J}/{^\circ}\text{C}
  2. Determine the total heat capacity of the calorimeter assembly: Ctotal=Cw+Ccal=1046.5 J/∘C+45.0 J/∘C=1091.5 J/∘CC_{\text{total}} = C_w + C_{\text{cal}} = 1046.5\text{ J}/{^\circ}\text{C} + 45.0\text{ J}/{^\circ}\text{C} = 1091.5\text{ J}/{^\circ}\text{C}
  3. Multiply by the measured temperature change ΔT\Delta T: Qabsorbed=(1091.5 J/∘C)⋅(7.40∘C)=8077.1 JQ_{\text{absorbed}} = (1091.5\text{ J}/{^\circ}\text{C}) \cdot (7.40{^\circ}\text{C}) = 8077.1\text{ J}

Rounding to three significant figures, consistent with the measurements:

Qabsorbed=8080 JQ_{\text{absorbed}} = 8080\text{ J}


03

Calculate the Percentage Heat Loss

By conservation of energy, the thermal energy lost to the surroundings is the difference between the electrical energy supplied and the energy captured inside the calorimeter:

Qlost=Ein−Qabsorbed=8640 J−8080 J=560 JQ_{\text{lost}} = E_{\text{in}} - Q_{\text{absorbed}} = 8640\text{ J} - 8080\text{ J} = 560\text{ J}

The percentage heat loss relative to the total electrical energy input is:

Percentage heat loss=QlostEin⋅100%=560 J8640 J⋅100%≈6.4815%\text{Percentage heat loss} = \frac{Q_{\text{lost}}}{E_{\text{in}}} \cdot 100\% = \frac{560\text{ J}}{8640\text{ J}} \cdot 100\% \approx 6.4815\%

Expressed to three significant figures:

Percentage heat loss=6.48%\text{Percentage heat loss} = 6.48\%

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student neglects the heat capacity of the calorimeter vessel and only accounts for the water when calculating the absorbed thermal energy, resulting in an overestimated percentage heat loss.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    Ein=VIΔt=(12.0)(2.40)(300.0)=8640 JE_{\text{in}} = V I \Delta t = (12.0)(2.40)(300.0) = 8640\text{ J}

  2. Step 2

    Qabsorbed=mwcwΔT  ⟹  Qabsorbed=(0.250)(4186)(7.40)=7744.1 JQ_{\text{absorbed}} = m_w c_w \Delta T \implies Q_{\text{absorbed}} = (0.250)(4186)(7.40) = 7744.1\text{ J}

    Correct

    Qabsorbed=(mwcw+Ccal)ΔT=((0.250)(4186)+45.0)(7.40)≈8080 JQ_{\text{absorbed}} = (m_w c_w + C_{\text{cal}})\Delta T = ((0.250)(4186) + 45.0)(7.40) \approx 8080\text{ J}

    You only accounted for the thermal energy absorbed by the water and left out the heat absorbed by the calorimeter container (CcalΔTC_{\text{cal}}\Delta T).

  3. Step 3

    Percentage heat loss=(8640−7744.18640)×100%  ⟹  Percentage heat loss=(895.98640)×100%=10.4%\text{Percentage heat loss} = \left(\frac{8640 - 7744.1}{8640}\right) \times 100\% \implies \text{Percentage heat loss} = \left(\frac{895.9}{8640}\right) \times 100\% = 10.4\%

    Correct

    Percentage heat loss=(8640−8077.18640)×100%=6.48%\text{Percentage heat loss} = \left(\frac{8640 - 8077.1}{8640}\right) \times 100\% = 6.48\%

    Your formula for heat loss percentage was applied correctly, but the result was skewed by the incorrect value of QabsorbedQ_{\text{absorbed}} from the previous step.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly set up and evaluated the electrical energy delivered by the DC supply.

You set up the percentage heat loss formula properly using the difference between input and absorbed energy.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Omission of Calorimeter Heat Capacity

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You modeled the absorbing system as containing only water, neglecting the thermal capacity of the calorimeter container itself (CcalC_{\text{cal}}) that is also in thermal contact and warms up by ΔT\Delta T.

REASONING PATH
Your ACEpath teacher’s suggested approach
Total System Heat Capacity
  • In a calorimetry experiment, all components undergoing the temperature change absorb heat: Ctotal=mwcw+CcalC_{\text{total}} = m_w c_w + C_{\text{cal}}.

  • Check whether the calorimeter vessel, stirrer, or probe heat capacity is provided in the problem statement before calculating absorbed heat.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Add the calorimeter heat capacity to the water heat capacity: Ctotal=(0.250 kg)(4186 J/(kg⋅∘C))+45.0 J/∘C=1046.5+45.0=1091.5 J/∘CC_{\text{total}} = (0.250\text{ kg})(4186\text{ J}/(\text{kg}\cdot{^\circ}\text{C})) + 45.0\text{ J}/{^\circ}\text{C} = 1046.5 + 45.0 = 1091.5\text{ J}/{^\circ}\text{C}.

  2. Multiply by the temperature change: Qabsorbed=(1091.5 J/∘C)(7.40∘C)=8077.1 J≈8080 JQ_{\text{absorbed}} = (1091.5\text{ J}/{^\circ}\text{C})(7.40{^\circ}\text{C}) = 8077.1\text{ J} \approx 8080\text{ J}.

  3. Recalculate the percentage heat loss: Percentage heat loss=8640−8077.18640×100%=562.98640×100%≈6.48%\text{Percentage heat loss} = \frac{8640 - 8077.1}{8640} \times 100\% = \frac{562.9}{8640} \times 100\% \approx 6.48\%.

Final answer

(a) Ein=8640 JE_{\text{in}} = 8640\text{ J}; (b) Qabsorbed=8080 JQ_{\text{absorbed}} = 8080\text{ J}; (c) Percentage heat loss =6.48%= 6.48\%

NEXT STEPS
Final Takeaways from Your Teacher
  • Always write down the full system boundary in calorimetry problems (Qtotal=Qwater+QcalorimeterQ_{\text{total}} = Q_{\text{water}} + Q_{\text{calorimeter}}) before plugging in numbers.

  • Double-check given data to make sure every provided parameter, such as CcalC_{\text{cal}}, has been actively used or explicitly verified as unnecessary.

OverviewACEpath Teacher's Diagnosis

02 The student calculates the percentage efficiency or heat retained rather than the percentage heat loss.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    Ein=VIΔt=(12.0)(2.40)(300.0)=8640 JE_{\text{in}} = V I \Delta t = (12.0)(2.40)(300.0) = 8640\text{ J}

  2. Step 2

    Qabsorbed=(0.250×4186+45.0)(7.40)  ⟹  Qabsorbed=(1046.5+45.0)(7.40)=8077.1 JQ_{\text{absorbed}} = (0.250 \times 4186 + 45.0)(7.40) \implies Q_{\text{absorbed}} = (1046.5 + 45.0)(7.40) = 8077.1\text{ J}

  3. Step 3

    Percentage heat loss=(QabsorbedEin)×100%  ⟹  (8077.18640)×100%=93.5%\text{Percentage heat loss} = \left(\frac{Q_{\text{absorbed}}}{E_{\text{in}}}\right) \times 100\% \implies \left(\frac{8077.1}{8640}\right) \times 100\% = 93.5\%

    Correct

    Percentage heat loss=Ein−QabsorbedEin×100%=8640 J−8080 J8640 J×100%≈6.48%\text{Percentage heat loss} = \frac{E_{\text{in}} - Q_{\text{absorbed}}}{E_{\text{in}}} \times 100\% = \frac{8640\text{ J} - 8080\text{ J}}{8640\text{ J}} \times 100\% \approx 6.48\%

    You computed the ratio of absorbed energy to input energy, which represents the efficiency or fraction retained (93.5%93.5\%), instead of the fraction of energy dissipated to the surroundings.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly applied the formula for electrical energy delivered over time.

You accounted for both the water and the calorimeter vessel when calculating total heat capacity.

You performed accurate arithmetic through the intermediate steps.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Quantity Substitution Error

Confused energy absorbed (retained) with energy lost to surroundings

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You defined percentage loss directly using QabsorbedQ_{\text{absorbed}} in the numerator instead of the lost thermal energy Qlost=Ein−QabsorbedQ_{\text{lost}} = E_{\text{in}} - Q_{\text{absorbed}}.

REASONING PATH
Your ACEpath teacher’s suggested approach
Distinguishing Retained vs. Lost Energy
  • In an open or imperfectly insulated thermal system, Ein=Qabsorbed+QlostE_{\text{in}} = Q_{\text{absorbed}} + Q_{\text{lost}}, so Qlost=Ein−QabsorbedQ_{\text{lost}} = E_{\text{in}} - Q_{\text{absorbed}}.

  • Always find the difference Qlost=Ein−QabsorbedQ_{\text{lost}} = E_{\text{in}} - Q_{\text{absorbed}} before dividing by EinE_{\text{in}}, or subtract the percentage retained from 100%100\%.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Find the energy lost to the surroundings: Qlost=Ein−Qabsorbed=8640 J−8077.1 J=562.9 JQ_{\text{lost}} = E_{\text{in}} - Q_{\text{absorbed}} = 8640\text{ J} - 8077.1\text{ J} = 562.9\text{ J} (or 8640 J−8080 J=560 J8640\text{ J} - 8080\text{ J} = 560\text{ J}).

  2. Calculate the percentage relative to the input energy: Percentage heat loss=QlostEin×100%=560 J8640 J×100%≈6.48%\text{Percentage heat loss} = \frac{Q_{\text{lost}}}{E_{\text{in}}} \times 100\% = \frac{560\text{ J}}{8640\text{ J}} \times 100\% \approx 6.48\%.

Final answer

(a) Ein=8640 JE_{\text{in}} = 8640\text{ J}; (b) Qabsorbed=8080 JQ_{\text{absorbed}} = 8080\text{ J}; (c) Percentage heat loss=6.48%\text{Percentage heat loss} = 6.48\%

NEXT STEPS
Final Takeaways from Your Teacher
  • Before calculating a percentage, explicitly define the numerator quantity (here, QlostQ_{\text{lost}}) rather than inserting an already calculated intermediate variable (QabsorbedQ_{\text{absorbed}}).

  • Perform a sanity check on your result: an insulated calorimeter should lose a small percentage of heat, not over 90%90\%.

OverviewACEpath Teacher's Diagnosis

03 The student divides the heat loss by the thermal energy absorbed instead of the energy input when computing the percentage heat loss.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    Ein=VIΔt=(12.0)(2.40)(300.0)=8640 JE_{\text{in}} = V I \Delta t = (12.0)(2.40)(300.0) = 8640\text{ J}

  2. Step 2

    Qabsorbed=((0.250)(4186)+45.0)(7.40)=8077.1 JQ_{\text{absorbed}} = ((0.250)(4186) + 45.0)(7.40) = 8077.1\text{ J}

  3. Step 3

    Heat loss=8640−8077.1=562.9 J\text{Heat loss} = 8640 - 8077.1 = 562.9\text{ J}

  4. Step 4

    Percentage heat loss=(562.98077.1)×100%=6.97%\text{Percentage heat loss} = \left(\frac{562.9}{8077.1}\right) \times 100\% = 6.97\%

    Correct

    Percentage heat loss=(QlostEin)×100%=(562.9 J8640 J)×100%=6.51%\text{Percentage heat loss} = \left(\frac{Q_{\text{lost}}}{E_{\text{in}}}\right) \times 100\% = \left(\frac{562.9\text{ J}}{8640\text{ J}}\right) \times 100\% = 6.51\% (or 560 J8640 J×100%=6.48%\frac{560\text{ J}}{8640\text{ J}} \times 100\% = 6.48\%)

    You divided the energy lost by the thermal energy absorbed (Qabsorbed=8077.1 JQ_{\text{absorbed}} = 8077.1\text{ J}) instead of the total energy input (Ein=8640 JE_{\text{in}} = 8640\text{ J}). The problem specifies finding the percentage loss relative to EinE_{\text{in}}.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly used the formula Ein=VIΔtE_{\text{in}} = V I \Delta t to compute the electrical input energy.

You properly accounted for both the water and the calorimeter vessel heat capacities when determining QabsorbedQ_{\text{absorbed}}.

You correctly found the energy difference representing the heat lost to the surroundings.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Incorrect Reference Base in Percentage Ratio

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You selected the final absorbed thermal energy (QabsorbedQ_{\text{absorbed}}) as the denominator instead of the initial reference energy supplied to the system (EinE_{\text{in}}). In efficiency and loss calculations, fractional loss is defined relative to the total input energy.

REASONING PATH
Your ACEpath teacher’s suggested approach
Identifying the Reference Base in Percentage Calculations
  • When calculating percentage loss or fractional efficiency relative to an input quantity EinE_{\text{in}}, the input quantity must always be the denominator: Percentage loss=LossEin×100%\text{Percentage loss} = \frac{\text{Loss}}{E_{\text{in}}} \times 100\%.

  • Always verify whether the denominator represents the total initial input or an intermediate/output quantity before computing a percentage.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Identify the reference base requested by the problem: relative to Ein=8640 JE_{\text{in}} = 8640\text{ J}.

  2. Set up the ratio of heat lost to total energy supplied: QlostEin=560 J8640 J\frac{Q_{\text{lost}}}{E_{\text{in}}} = \frac{560\text{ J}}{8640\text{ J}} (or 562.9 J8640 J\frac{562.9\text{ J}}{8640\text{ J}}).

  3. Multiply by 100%100\% and round to three significant figures: 5608640×100%=6.48%\frac{560}{8640} \times 100\% = 6.48\%.

Final answer

(a) Ein=8640 JE_{\text{in}} = 8640\text{ J}; (b) Qabsorbed=8080 JQ_{\text{absorbed}} = 8080\text{ J}; (c) Percentage heat loss =6.48%= 6.48\% (or 6.51%6.51\% using unrounded intermediate values)

NEXT STEPS
Final Takeaways from Your Teacher
  • Read the question phrasing carefully to pinpoint the stated reference base (e.g., 'relative to EinE_{\text{in}}').

  • Check whether your ratio corresponds to (loss)/(input) rather than (loss)/(output).

  • Practice expressing physical losses and efficiencies as fractions of total source energy.

Lock it in

Similar question

01

An electrical heater supplies 5000 J5000\text{ J} of energy to a calorimeter containing 0.200 kg0.200\text{ kg} of liquid (c=2500 J/(kg⋅∘C)c = 2500\text{ J}/(\text{kg}\cdot{^\circ}\text{C})). The calorimeter cup has a heat capacity of 50.0 J/∘C50.0\text{ J}/{^\circ}\text{C}. The temperature rises by 8.00∘C8.00{^\circ}\text{C}. Determine the heat absorbed by the system and the percentage heat loss relative to input energy.

Answer

Qabsorbed=(mc+Ccal)ΔT=((0.200)(2500)+50.0)(8.00)=(500+50)(8.00)=4400 JQ_{\text{absorbed}} = (m c + C_{\text{cal}})\Delta T = ((0.200)(2500) + 50.0)(8.00) = (500 + 50)(8.00) = 4400\text{ J}. Percentage heat loss =5000−44005000×100%=12.0%= \frac{5000 - 4400}{5000} \times 100\% = 12.0\%.

02

In an experiment, an electrical input of Ein=12,000 JE_{\text{in}} = 12{,}000\text{ J} heats 0.400 kg0.400\text{ kg} of water (cw=4186 J/(kg⋅∘C)c_w = 4186\text{ J}/(\text{kg}\cdot{^\circ}\text{C})) inside an aluminum calorimeter cup of mass 0.150 kg0.150\text{ kg} (cAl=900 J/(kg⋅∘C)c_{\text{Al}} = 900\text{ J}/(\text{kg}\cdot{^\circ}\text{C})). The measured temperature rise is ΔT=6.20∘C\Delta T = 6.20{^\circ}\text{C}. Calculate: (a) the total heat capacity CtotalC_{\text{total}}, (b) the thermal energy absorbed, and (c) the energy lost to the surroundings in joules.

Answer

(a) Ctotal=mwcw+mAlcAl=(0.400)(4186)+(0.150)(900)=1674.4+135=1809.4 J/∘CC_{\text{total}} = m_w c_w + m_{\text{Al}} c_{\text{Al}} = (0.400)(4186) + (0.150)(900) = 1674.4 + 135 = 1809.4\text{ J}/{^\circ}\text{C}. (b) Qabsorbed=1809.4×6.20≈11,218 JQ_{\text{absorbed}} = 1809.4 \times 6.20 \approx 11{,}218\text{ J} (or 11,200 J11{,}200\text{ J} to 3 sig figs). (c) Qlost=12,000−11,218=782 JQ_{\text{lost}} = 12{,}000 - 11{,}218 = 782\text{ J}.

03

A student supplies Ein=6000 JE_{\text{in}} = 6000\text{ J} of electrical energy to a calorimeter with mw=0.150 kgm_w = 0.150\text{ kg} of water (cw=4186 J/(kg⋅∘C)c_w = 4186\text{ J}/(\text{kg}\cdot{^\circ}\text{C})) and vessel heat capacity Ccal=60.0 J/∘CC_{\text{cal}} = 60.0\text{ J}/{^\circ}\text{C}, measuring ΔT=8.00∘C\Delta T = 8.00{^\circ}\text{C}. (a) Calculate the correct percentage heat loss. (b) Calculate the erroneous percentage heat loss if CcalC_{\text{cal}} is neglected. (c) State by how many percentage points the error overestimates the heat loss.

Answer

(a) Ctotal=(0.150)(4186)+60.0=627.9+60.0=687.9 J/∘CC_{\text{total}} = (0.150)(4186) + 60.0 = 627.9 + 60.0 = 687.9\text{ J}/{^\circ}\text{C}. Qabsorbed=687.9×8.00=5503.2 JQ_{\text{absorbed}} = 687.9 \times 8.00 = 5503.2\text{ J}. Percentage loss =6000−5503.26000×100%=8.28%= \frac{6000 - 5503.2}{6000} \times 100\% = 8.28\%. (b) Erroneous Q=627.9×8.00=5023.2 JQ = 627.9 \times 8.00 = 5023.2\text{ J}. Erroneous loss =6000−5023.26000×100%=16.28%= \frac{6000 - 5023.2}{6000} \times 100\% = 16.28\%. (c) Difference =16.28%−8.28%=8.00= 16.28\% - 8.28\% = 8.00 percentage points.

Loading workspace…