Resources

A structural steel cable of original unstretched length L0=4.50 mL_0 = 4.50\text{ m} and uniform circular cross-sectional radius r=3.20 mmr = 3.20\text{ mm} supports a suspended load of mass m=850 kgm = 850\text{ kg}. The Young's modulus of this steel alloy is E=2.00×1011 PaE = 2.00 \times 10^{11}\text{ Pa}, and the acceleration due to gravity is g=9.80 m/s2g = 9.80\text{ m/s}^2. Assuming the cable deforms elastically and neglecting the mass of the cable itself, calculate: (a) the tensile stress σ\sigma developed in the cable, (b) the tensile strain ε\varepsilon, and (c) the total elongation ΔL\Delta L of the cable in millimeters.

Answer and steps

Final answer

(a) σ=2.59×108 Pa\sigma = 2.59 \times 10^8\text{ Pa}; (b) ε=1.29×10−3\varepsilon = 1.29 \times 10^{-3}; (c) ΔL=5.82 mm\Delta L = 5.82\text{ mm}

Steps

Part (a): Tensile Stress (σ\sigma)

  1. Calculate the tension force (FF) acting on the cable: The tension in the cable is equal to the gravitational weight of the suspended load: F=m⋅g=850 kg⋅9.80 m/s2=8330 NF = m \cdot g = 850\text{ kg} \cdot 9.80\text{ m/s}^2 = 8330\text{ N}
  2. Calculate the cross-sectional area (AA) of the cable: Convert the radius to meters: r=3.20 mm=3.20×10−3 mr = 3.20\text{ mm} = 3.20 \times 10^{-3}\text{ m}. A=πr2=π(3.20×10−3 m)2≈3.217×10−5 m2A = \pi r^2 = \pi (3.20 \times 10^{-3}\text{ m})^2 \approx 3.217 \times 10^{-5}\text{ m}^2
  3. Compute the tensile stress (σ\sigma): Tensile stress is defined as the force applied per unit cross-sectional area: σ=FA=8330 N3.217×10−5 m2≈2.589×108 Pa\sigma = \frac{F}{A} = \frac{8330\text{ N}}{3.217 \times 10^{-5}\text{ m}^2} \approx 2.589 \times 10^8\text{ Pa} Rounded to three significant figures: σ=2.59×108 Pa\sigma = 2.59 \times 10^8\text{ Pa}

Part (b): Tensile Strain (ε\varepsilon)

  1. Relate stress and strain using Hooke's Law: For elastic deformation, stress is proportional to strain via Young's modulus (EE): σ=E⋅ε  ⟹  ε=σE\sigma = E \cdot \varepsilon \implies \varepsilon = \frac{\sigma}{E}
  2. Calculate the tensile strain (ε\varepsilon): ε=2.589×108 Pa2.00×1011 Pa≈1.294×10−3\varepsilon = \frac{2.589 \times 10^8\text{ Pa}}{2.00 \times 10^{11}\text{ Pa}} \approx 1.294 \times 10^{-3} Rounded to three significant figures: ε=1.29×10−3\varepsilon = 1.29 \times 10^{-3} (Note: Strain is a dimensionless quantity representing relative deformation.)

Part (c): Total Elongation (ΔL\Delta L)

  1. Relate strain to change in length: By definition, tensile strain is the ratio of elongation (ΔL\Delta L) to the original unstretched length (L0L_0): ε=ΔLL0  ⟹  ΔL=ε⋅L0\varepsilon = \frac{\Delta L}{L_0} \implies \Delta L = \varepsilon \cdot L_0
  2. Compute the elongation (ΔL\Delta L): Using the strain value: ΔL=(1.294×10−3)⋅4.50 m≈5.823×10−3 m\Delta L = (1.294 \times 10^{-3}) \cdot 4.50\text{ m} \approx 5.823 \times 10^{-3}\text{ m}
  3. Convert to millimeters: ΔL=5.823×10−3 m⋅1000 mm1 m≈5.82 mm\Delta L = 5.823 \times 10^{-3}\text{ m} \cdot \frac{1000\text{ mm}}{1\text{ m}} \approx 5.82\text{ mm}

Common Pitfall to Avoid:

  • Unit conversions: Forgetting to convert the radius from millimeters to meters before calculating the area AA leads to an error of several orders of magnitude in both stress and strain.

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student treats the given mass as the tension force instead of multiplying by gravitational acceleration, underestimating the tensile stress.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    F=850 NF = 850\text{ N}

    Correct

    F=mg=(850 kg)(9.80 m/s2)=8330 NF = mg = (850\text{ kg})(9.80\text{ m/s}^2) = 8330\text{ N}

    You treated the given mass of 850 kg850\text{ kg} directly as a force of 850 N850\text{ N}. To find the tension supporting a suspended static load, you need to calculate the weight by multiplying mass by gravity: F=mgF = mg.

  2. Step 2

    A=π⋅(0.00320 m)2=3.217⋅10−5 m2A = \pi \cdot (0.00320\text{ m})^2 = 3.217 \cdot 10^{-5}\text{ m}^2

  3. Step 3

    σ=850 N3.217⋅10−5 m2=2.64⋅107 Pa\sigma = \frac{850\text{ N}}{3.217 \cdot 10^{-5}\text{ m}^2} = 2.64 \cdot 10^7\text{ Pa}

    Correct

    σ=FA=8330 N3.217×10−5 m2≈2.59×108 Pa\sigma = \frac{F}{A} = \frac{8330\text{ N}}{3.217 \times 10^{-5}\text{ m}^2} \approx 2.59 \times 10^8\text{ Pa}

    Your formula for tensile stress σ=FA\sigma = \frac{F}{A} is correct, but your numerical result is smaller by a factor of 9.809.80 because it uses your incorrect force from Step 1.

  4. Step 4

    ε=σE=2.642⋅107 Pa2.00⋅1011 Pa=1.32⋅10−4\varepsilon = \frac{\sigma}{E} = \frac{2.642 \cdot 10^7\text{ Pa}}{2.00 \cdot 10^{11}\text{ Pa}} = 1.32 \cdot 10^{-4}

    Correct

    ε=σE=2.589×108 Pa2.00×1011 Pa≈1.29×10−3\varepsilon = \frac{\sigma}{E} = \frac{2.589 \times 10^8\text{ Pa}}{2.00 \times 10^{11}\text{ Pa}} \approx 1.29 \times 10^{-3}

    You correctly applied Hooke's law in the form ε=σE\varepsilon = \frac{\sigma}{E}, but the value is affected by the understated stress.

  5. Step 5

    ΔL=ε⋅L0=1.321⋅10−4⋅4.50 m=5.94⋅10−4 m=0.594 mm\Delta L = \varepsilon \cdot L_0 = 1.321 \cdot 10^{-4} \cdot 4.50\text{ m} = 5.94 \cdot 10^{-4}\text{ m} = 0.594\text{ mm}

    Correct

    ΔL=εL0=(1.294×10−3)(4.50 m)≈5.82×10−3 m=5.82 mm\Delta L = \varepsilon L_0 = (1.294 \times 10^{-3})(4.50\text{ m}) \approx 5.82 \times 10^{-3}\text{ m} = 5.82\text{ mm}

    Your definition for elongation ΔL=εL0\Delta L = \varepsilon L_0 and conversion to millimeters are correct, but your final answer is an order of magnitude too small due to the initial force error.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly converted the radius from millimeters to meters before squaring it in the area formula.

You applied the correct definition for tensile stress σ=FA\sigma = \frac{F}{A}.

You related stress and strain properly through Young's modulus using ε=σE\varepsilon = \frac{\sigma}{E}.

You correctly converted the calculated elongation from meters to millimeters.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Mass vs. Weight Confusion

You wrote F=850 NF = 850\text{ N} instead of calculating the weight force W=mg=(850 kg)(9.80 m/s2)W = mg = (850\text{ kg})(9.80\text{ m/s}^2).

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You conflated mass (mm, measured in kg\text{kg}) with gravitational weight force (FgF_g, measured in N\text{N}). When a load is suspended at rest, the upward tension in the cable must balance the downward gravitational force F=mgF = mg, not simply equal the numerical mass value.

REASONING PATH
Your ACEpath teacher’s suggested approach
Mass to Force Conversion
  • A suspended static mass mm exerts a downward weight force of F=mgF = mg, where g≈9.80 m/s2g \approx 9.80\text{ m/s}^2.

  • Always verify units: if a quantity is given in kilograms, multiply by gg to find the force in newtons before calculating stress.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Calculate the gravitational tension force: F=mg=(850 kg)(9.80 m/s2)=8330 NF = mg = (850\text{ kg})(9.80\text{ m/s}^2) = 8330\text{ N}.

  2. Compute tensile stress: σ=FA=8330 N3.217×10−5 m2≈2.589×108 Pa=2.59×108 Pa\sigma = \frac{F}{A} = \frac{8330\text{ N}}{3.217 \times 10^{-5}\text{ m}^2} \approx 2.589 \times 10^8\text{ Pa} = 2.59 \times 10^8\text{ Pa}.

  3. Compute tensile strain: ε=σE=2.589×108 Pa2.00×1011 Pa≈1.294×10−3=1.29×10−3\varepsilon = \frac{\sigma}{E} = \frac{2.589 \times 10^8\text{ Pa}}{2.00 \times 10^{11}\text{ Pa}} \approx 1.294 \times 10^{-3} = 1.29 \times 10^{-3}.

  4. Compute total elongation: ΔL=εL0=(1.294×10−3)(4.50 m)≈5.823×10−3 m=5.82 mm\Delta L = \varepsilon L_0 = (1.294 \times 10^{-3})(4.50\text{ m}) \approx 5.823 \times 10^{-3}\text{ m} = 5.82\text{ mm}.

Final answer

(a) σ=2.59×108 Pa\sigma = 2.59 \times 10^8\text{ Pa}; (b) ε=1.29×10−3\varepsilon = 1.29 \times 10^{-3}; (c) ΔL=5.82 mm\Delta L = 5.82\text{ mm}

NEXT STEPS
Final Takeaways from Your Teacher
  • When you read a physics problem, circle the given units: if you see kilograms (kg\text{kg}), immediately remind yourself to multiply by gg to obtain newtons (N\text{N}) whenever a force is required.

  • Practice drawing a quick free-body diagram of suspended objects to explicitly write T=mgT = mg before substituting numbers.

OverviewACEpath Teacher's Diagnosis

02 The student forgets to convert the radius from millimeters to meters when finding the cross-sectional area, yielding an incorrect area and stress by a factor of 10⁶.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    F=850 kg⋅9.80 m/s2=8330 NF = 850\text{ kg} \cdot 9.80\text{ m/s}^2 = 8330\text{ N}

  2. Step 2

    A=π⋅(3.20)2=32.17 m2A = \pi \cdot (3.20)^2 = 32.17\text{ m}^2

    Correct

    A=πr2=π(3.20×10−3 m)2≈3.22×10−5 m2A = \pi r^2 = \pi (3.20 \times 10^{-3}\text{ m})^2 \approx 3.22 \times 10^{-5}\text{ m}^2

    You used the radius value directly as 3.203.20 without converting millimeters to meters (1 mm=10−3 m1\text{ mm} = 10^{-3}\text{ m}). As a result, the cross-sectional area was overestimated by a factor of 10610^6.

  3. Step 3

    σ=8330 N32.17 m2=259 Pa\sigma = \frac{8330\text{ N}}{32.17\text{ m}^2} = 259\text{ Pa}

    Correct

    σ=FA=8330 N3.217×10−5 m2≈2.59×108 Pa\sigma = \frac{F}{A} = \frac{8330\text{ N}}{3.217 \times 10^{-5}\text{ m}^2} \approx 2.59 \times 10^8\text{ Pa}

    Your formula σ=FA\sigma = \frac{F}{A} and division were carried out properly, but the numerical result is too small because it used the incorrect area from step 2.

  4. Step 4

    ε=σE=258.9 Pa2.00⋅1011 Pa=1.29⋅10−9\varepsilon = \frac{\sigma}{E} = \frac{258.9\text{ Pa}}{2.00 \cdot 10^{11}\text{ Pa}} = 1.29 \cdot 10^{-9}

    Correct

    ε=σE=2.589×108 Pa2.00×1011 Pa≈1.29×10−3\varepsilon = \frac{\sigma}{E} = \frac{2.589 \times 10^8\text{ Pa}}{2.00 \times 10^{11}\text{ Pa}} \approx 1.29 \times 10^{-3}

    You applied Hooke's law correctly to find strain, but the value inherits the error from your stress calculation.

  5. Step 5

    ΔL=ε⋅L0=1.2947⋅10−9⋅4.50 m=5.83⋅10−9 m=5.83⋅10−6 mm\Delta L = \varepsilon \cdot L_0 = 1.2947 \cdot 10^{-9} \cdot 4.50\text{ m} = 5.83 \cdot 10^{-9}\text{ m} = 5.83 \cdot 10^{-6}\text{ mm}

    Correct

    ΔL=ε⋅L0=(1.294×10−3)⋅4.50 m≈5.82×10−3 m=5.82 mm\Delta L = \varepsilon \cdot L_0 = (1.294 \times 10^{-3}) \cdot 4.50\text{ m} \approx 5.82 \times 10^{-3}\text{ m} = 5.82\text{ mm}

    Your formula and unit conversion at the end were completely correct, but the final elongation is off because of the earlier radius conversion error.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly calculated the tension force as the gravitational weight of the load.

You used the correct definition of tensile stress as force per unit area.

You correctly applied Hooke's law to relate stress, strain, and Young's modulus.

You correctly related tensile strain to the total elongation and original length.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Missing SI unit conversion for length before squaring

You substituted the radius in millimeters directly into the area formula without converting it to meters first.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Overlooking that geometric parameters with prefixes (like mm\text{mm}) must be converted to base SI units (m\text{m}) before calculating derived quantities (like m2\text{m}^2), leading to an area error proportional to (10−3)2=10−6(10^{-3})^2 = 10^{-6}.

REASONING PATH
Your ACEpath teacher’s suggested approach
Check SI unit compatibility
  • Pascal is defined as N/m2\text{N/m}^2, so all linear dimensions used for cross-sectional area must be in meters (m\text{m}).

  • Always convert millimeters to meters (r=3.20 mm=3.20×10−3 mr = 3.20\text{ mm} = 3.20 \times 10^{-3}\text{ m}) before squaring.

Sanity check physical plausibility
  • A thin structural steel cable (radius 3.2 mm3.2\text{ mm}) carrying nearly 1 metric ton1\text{ metric ton} experiences significant stress (typically on the order of 108 Pa10^8\text{ Pa}) and elongates by a few millimeters.

  • Compare your calculated stress to ambient pressure or material limits: 259 Pa259\text{ Pa} is unrealistically small for supporting 850 kg850\text{ kg}.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. r=3.20 mm=3.20×10−3 mr = 3.20\text{ mm} = 3.20 \times 10^{-3}\text{ m}

  2. A=πr2=π(3.20×10−3 m)2≈3.217×10−5 m2A = \pi r^2 = \pi (3.20 \times 10^{-3}\text{ m})^2 \approx 3.217 \times 10^{-5}\text{ m}^2

  3. σ=FA=8330 N3.217×10−5 m2≈2.589×108 Pa=2.59×108 Pa\sigma = \frac{F}{A} = \frac{8330\text{ N}}{3.217 \times 10^{-5}\text{ m}^2} \approx 2.589 \times 10^8\text{ Pa} = 2.59 \times 10^8\text{ Pa}

  4. ε=σE=2.589×108 Pa2.00×1011 Pa≈1.294×10−3=1.29×10−3\varepsilon = \frac{\sigma}{E} = \frac{2.589 \times 10^8\text{ Pa}}{2.00 \times 10^{11}\text{ Pa}} \approx 1.294 \times 10^{-3} = 1.29 \times 10^{-3}

  5. ΔL=ε⋅L0=(1.294×10−3)⋅4.50 m=5.823×10−3 m=5.82 mm\Delta L = \varepsilon \cdot L_0 = (1.294 \times 10^{-3}) \cdot 4.50\text{ m} = 5.823 \times 10^{-3}\text{ m} = 5.82\text{ mm}

Final answer

(a) σ=2.59×108 Pa\sigma = 2.59 \times 10^8\text{ Pa}; (b) ε=1.29×10−3\varepsilon = 1.29 \times 10^{-3}; (c) ΔL=5.82 mm\Delta L = 5.82\text{ mm}

NEXT STEPS
Final Takeaways from Your Teacher
  • Form the habit of converting all given quantities with metric prefixes (such as mm\text{mm}, cm\text{cm}, or kN\text{kN}) into standard SI base units at the very beginning of the problem.

  • Practice checking whether squaring an area dimension magnifies prefix conversions, noting that (10−3 m)2=10−6 m2(10^{-3}\text{ m})^2 = 10^{-6}\text{ m}^2.

OverviewACEpath Teacher's Diagnosis

03 The student uses the circumference formula 2·π·r instead of the area formula π·r² to compute the cross-sectional area, underestimating the area and overestimating stress.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    F=850 kg⋅9.80 m/s2=8330 NF = 850\text{ kg} \cdot 9.80\text{ m/s}^2 = 8330\text{ N}

  2. Step 2

    A=2⋅π⋅(3.20⋅10−3 m)=2.011⋅10−2 m2A = 2 \cdot \pi \cdot (3.20 \cdot 10^{-3}\text{ m}) = 2.011 \cdot 10^{-2}\text{ m}^2

    Correct

    A=πr2=π(3.20×10−3 m)2≈3.217×10−5 m2A = \pi r^2 = \pi (3.20 \times 10^{-3}\text{ m})^2 \approx 3.217 \times 10^{-5}\text{ m}^2

    You applied the circumference formula C=2πrC = 2\pi r rather than the circular cross-sectional area formula A=πr2A = \pi r^2.

  3. Step 3

    σ=8330 N/(2.011⋅10−2 m2)=4.14⋅105 Pa\sigma = 8330\text{ N} / (2.011 \cdot 10^{-2}\text{ m}^2) = 4.14 \cdot 10^5\text{ Pa}

    Correct

    σ=FA=8330 N3.217×10−5 m2≈2.59×108 Pa\sigma = \frac{F}{A} = \frac{8330\text{ N}}{3.217 \times 10^{-5}\text{ m}^2} \approx 2.59 \times 10^8\text{ Pa}

    Your definition of tensile stress σ=FA\sigma = \frac{F}{A} was correct, but the result is numerically incorrect due to the area calculation error in Step 2.

  4. Step 4

    ε=σE=4.142⋅105 Pa2.00⋅1011 Pa=2.07⋅10−6\varepsilon = \frac{\sigma}{E} = \frac{4.142 \cdot 10^5\text{ Pa}}{2.00 \cdot 10^{11}\text{ Pa}} = 2.07 \cdot 10^{-6}

    Correct

    ε=σE=2.589×108 Pa2.00×1011 Pa≈1.29×10−3\varepsilon = \frac{\sigma}{E} = \frac{2.589 \times 10^8\text{ Pa}}{2.00 \times 10^{11}\text{ Pa}} \approx 1.29 \times 10^{-3}

    You correctly applied Hooke's law in the form ε=σE\varepsilon = \frac{\sigma}{E}, but your input stress was carried over from Step 3.

  5. Step 5

    ΔL=ε⋅L0=2.071⋅10−6⋅4.50 m=9.32⋅10−6 m=9.32⋅10−3 mm\Delta L = \varepsilon \cdot L_0 = 2.071 \cdot 10^{-6} \cdot 4.50\text{ m} = 9.32 \cdot 10^{-6}\text{ m} = 9.32 \cdot 10^{-3}\text{ mm}

    Correct

    ΔL=ε⋅L0=(1.294×10−3)(4.50 m)≈5.82 mm\Delta L = \varepsilon \cdot L_0 = (1.294 \times 10^{-3})(4.50\text{ m}) \approx 5.82\text{ mm}

    Your elongation formula ΔL=ε⋅L0\Delta L = \varepsilon \cdot L_0 and your unit conversion to millimeters were executed properly, but the numerical answer inherits the earlier error.

WHAT YOU DID WELL
Compliments from Your Teacher

You calculated the gravitational load F=mgF = mg accurately.

You properly identified the governing formulas for tensile stress σ=FA\sigma = \frac{F}{A}, tensile strain ε=σE\varepsilon = \frac{\sigma}{E}, and elongation ΔL=εL0\Delta L = \varepsilon L_0.

You converted radius millimeters to meters and final elongation meters to millimeters correctly.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Formula confusion between circumference and area

You wrote 2πr2\pi r instead of squaring the radius in πr2\pi r^2.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You conflated the one-dimensional boundary perimeter (circumference 2πr2\pi r) of a circle with its two-dimensional internal surface area (A=πr2A = \pi r^2).

REASONING PATH
Your ACEpath teacher’s suggested approach
Cross-Sectional Area vs. Circumference
  • Area has units of length squared ([L]2[\text{L}]^2). For a solid circular rod or cable, A=πr2=πd24A = \pi r^2 = \frac{\pi d^2}{4}, whereas 2πr2\pi r is the circumference.

  • Check the power of the radius before computing: an area formula must always contain a squared length term (r2r^2).

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Compute the correct circular area: A=πr2=π(3.20×10−3 m)2≈3.217×10−5 m2A = \pi r^2 = \pi (3.20 \times 10^{-3}\text{ m})^2 \approx 3.217 \times 10^{-5}\text{ m}^2.

  2. Calculate tensile stress: σ=8330 N3.217×10−5 m2≈2.59×108 Pa\sigma = \frac{8330\text{ N}}{3.217 \times 10^{-5}\text{ m}^2} \approx 2.59 \times 10^8\text{ Pa}.

  3. Calculate tensile strain: ε=σE=2.589×108 Pa2.00×1011 Pa≈1.29×10−3\varepsilon = \frac{\sigma}{E} = \frac{2.589 \times 10^8\text{ Pa}}{2.00 \times 10^{11}\text{ Pa}} \approx 1.29 \times 10^{-3}.

  4. Calculate elongation: ΔL=ε⋅L0=(1.294×10−3)(4.50 m)≈5.82×10−3 m=5.82 mm\Delta L = \varepsilon \cdot L_0 = (1.294 \times 10^{-3})(4.50\text{ m}) \approx 5.82 \times 10^{-3}\text{ m} = 5.82\text{ mm}.

Final answer

(a) σ=2.59×108 Pa\sigma = 2.59 \times 10^8\text{ Pa}, (b) ε=1.29×10−3\varepsilon = 1.29 \times 10^{-3}, (c) ΔL=5.82 mm\Delta L = 5.82\text{ mm}

NEXT STEPS
Final Takeaways from Your Teacher
  • Double-check dimensional units whenever you write geometric formulas: area must always involve meters squared (m2\text{m}^2).

  • Review circular cross sections in elasticity problems, keeping A=πr2A = \pi r^2 and C=2πrC = 2\pi r clearly distinguished.

Lock it in

Similar question

01

A brass rod with a circular cross-sectional area of A=2.50×10−5 m2A = 2.50 \times 10^{-5}\text{ m}^2 supports a suspended load of mass m=400 kgm = 400\text{ kg}. Taking g=9.80 m/s2g = 9.80\text{ m/s}^2, calculate the tensile stress σ\sigma in the rod.

Answer

σ=1.57×108 Pa\sigma = 1.57 \times 10^8\text{ Pa}. Key steps: F=mg=(400 kg)(9.80 m/s2)=3920 NF = mg = (400\text{ kg})(9.80\text{ m/s}^2) = 3920\text{ N}; σ=FA=3920 N2.50×10−5 m2=1.568×108 Pa≈1.57×108 Pa\sigma = \frac{F}{A} = \frac{3920\text{ N}}{2.50 \times 10^{-5}\text{ m}^2} = 1.568 \times 10^8\text{ Pa} \approx 1.57 \times 10^8\text{ Pa}.

02

An aluminum wire of original length L0=3.00 mL_0 = 3.00\text{ m} and radius r=1.50 mmr = 1.50\text{ mm} hangs vertically. A mass of m=150 kgm = 150\text{ kg} is attached to its lower end. If Young's modulus for aluminum is E=7.00×1010 PaE = 7.00 \times 10^{10}\text{ Pa} and g=9.80 m/s2g = 9.80\text{ m/s}^2, determine: (a) the tensile strain ε\varepsilon, and (b) the elongation ΔL\Delta L in millimeters.

Answer

(a) ε=2.97×10−3\varepsilon = 2.97 \times 10^{-3}; (b) ΔL=8.91 mm\Delta L = 8.91\text{ mm}. Key steps: F=mg=1470 NF = mg = 1470\text{ N}; A=π(1.50×10−3 m)2≈7.069×10−6 m2A = \pi (1.50 \times 10^{-3}\text{ m})^2 \approx 7.069 \times 10^{-6}\text{ m}^2; σ=14707.069×10−6≈2.080×108 Pa\sigma = \frac{1470}{7.069 \times 10^{-6}} \approx 2.080 \times 10^8\text{ Pa}; ε=σE=2.080×1087.00×1010≈2.971×10−3\varepsilon = \frac{\sigma}{E} = \frac{2.080 \times 10^8}{7.00 \times 10^{10}} \approx 2.971 \times 10^{-3}; ΔL=εL0=(2.971×10−3)(3.00 m)≈8.91×10−3 m=8.91 mm\Delta L = \varepsilon L_0 = (2.971 \times 10^{-3})(3.00\text{ m}) \approx 8.91 \times 10^{-3}\text{ m} = 8.91\text{ mm}.

03

A steel elevator cable (E=2.00×1011 PaE = 2.00 \times 10^{11}\text{ Pa}) of length L0=25.0 mL_0 = 25.0\text{ m} must support a total suspended mass of m=1800 kgm = 1800\text{ kg}. If the maximum allowable tensile strain is εmax⁡=8.00×10−4\varepsilon_{\max} = 8.00 \times 10^{-4} and g=9.80 m/s2g = 9.80\text{ m/s}^2, find: (a) the minimum required cross-sectional radius rr of the cable in millimeters, and (b) the corresponding total elongation ΔL\Delta L in millimeters under this maximum strain.

Answer

(a) r=5.92 mmr = 5.92\text{ mm}; (b) ΔL=20.0 mm\Delta L = 20.0\text{ mm}. Key steps: F=mg=(1800 kg)(9.80 m/s2)=17640 NF = mg = (1800\text{ kg})(9.80\text{ m/s}^2) = 17640\text{ N}; maximum allowable stress σmax⁡=Eεmax⁡=(2.00×1011 Pa)(8.00×10−4)=1.60×108 Pa\sigma_{\max} = E \varepsilon_{\max} = (2.00 \times 10^{11}\text{ Pa})(8.00 \times 10^{-4}) = 1.60 \times 10^8\text{ Pa}; minimum area A=Fσmax⁡=176401.60×108=1.1025×10−4 m2A = \frac{F}{\sigma_{\max}} = \frac{17640}{1.60 \times 10^8} = 1.1025 \times 10^{-4}\text{ m}^2; r=Aπ=1.1025×10−4π≈5.924×10−3 m=5.92 mmr = \sqrt{\frac{A}{\pi}} = \sqrt{\frac{1.1025 \times 10^{-4}}{\pi}} \approx 5.924 \times 10^{-3}\text{ m} = 5.92\text{ mm}; elongation ΔL=εmax⁡L0=(8.00×10−4)(25.0 m)=0.0200 m=20.0 mm\Delta L = \varepsilon_{\max} L_0 = (8.00 \times 10^{-4})(25.0\text{ m}) = 0.0200\text{ m} = 20.0\text{ mm}.

Loading workspace…