Resources
A regional commuter train departs a terminal at along a straight railway. The onboard velocity telemetry is plotted in non-standard engineering units where time is measured in minutes () and velocity is recorded in kilometers per hour (). The graph exhibits three phases: (1) a linear rise from at to at ; (2) a constant cruising speed of from to ; (3) a uniform linear reduction from at down to at . Converting all quantities into standard SI units (, , and ): (a) calculate the acceleration during phase 1 in , and (b) determine the train's total displacement in meters from to .
Answer and steps
Final answer
(a) ; (b)
Steps
Convert Given Values to SI Units
Before calculating kinematic quantities, convert all velocities from kilometers per hour () to meters per second (), and all time intervals from minutes () to seconds ().
- Conversion factors:
- Velocities:
-
Time intervals:
- Phase 1:
- Phase 2:
- Phase 3:
Common Pitfall: Calculating slope () or displacement directly using the mixed units and without unit conversion leads to incompatible units such as instead of and .
(a) Acceleration During Phase 1
Acceleration is defined as the rate of change of velocity, which corresponds to the slope of the velocity-time graph:
For Phase 1:
(b) Total Displacement from to
On a velocity-time graph, displacement equals the area under the curve. We can compute the displacement for each of the three phases separately:
- Phase 1 (Triangle):
- Phase 2 (Rectangle):
- Phase 3 (Trapezoid):
Summing the displacements from each phase gives the total displacement:
Typical errors
01 The student forgets to convert the time intervals from minutes to seconds, calculating acceleration and displacement using minutes.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
You correctly converted to and recognized acceleration as the slope . However, you divided by directly instead of converting the interval into seconds ().
- Step 2Correct
You correctly selected the geometric area formulas (triangle, rectangle, trapezoid) and converted to . However, you used in minutes (, , ) rather than seconds (, , ).
- Step 3Correct
You correctly added the displacements from each phase, but your sum is off by a factor of because the phase displacements were computed using minutes.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly converted both non-zero speeds from to using the conversion factor of .
You correctly identified acceleration as the slope on a velocity-time graph.
You correctly partitioned the velocity-time graph into triangular, rectangular, and trapezoidal regions to evaluate displacement.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou used time values expressed in minutes directly in kinematic formulas that require seconds.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou treated the numerical time values on the graph axes as standard SI units without converting minutes to seconds, causing inconsistent unit combinations such as dividing by .
REASONING PATH
Your ACEpath teacher’s suggested approach- Check Base SI Units
Standard acceleration is measured in and displacement in , requiring time to be in seconds ().
Multiply time values given in minutes by before substituting them into kinematic equations or computing areas.
- Dimensional Analysis of Graph Area
.
Verify that multiplying the units of the vertical axis by the units of the horizontal axis yields meters.
CORRECTED PATH
ACEpath Teacher's DemonstrationConvert all time intervals to seconds: , , and .
Calculate Phase 1 acceleration: .
Calculate each phase displacement in meters: , , and .
Sum the phase displacements: .
(a) ; (b)
02 The student treats phase 3 as coming to a complete stop at 0 m/s instead of 36.0 km/h, resulting in an underestimated displacement in phase 3.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3
- Step 4Correct
The problem states that the train decelerates to (), not to rest (). The area under this phase is a trapezoid with parallel bases and , giving .
- Step 5Correct
Your method of summing the phase displacements was correct, but your final answer reflects the incorrect value propagated from phase 3.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly converted engineering units ( and ) to standard SI units ( and ).
You accurately used the slope of the velocity-time graph to compute acceleration for phase 1.
You correctly recognized that displacement corresponds to the geometric area under each segment of the velocity-time graph.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou treated the final velocity of phase 3 as instead of converting and substituting the given final velocity of .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisMisreading the ending condition of a deceleration phase as 'coming to rest' rather than decelerating to a non-zero intermediate speed.
REASONING PATH
Your ACEpath teacher’s suggested approach- Verify Boundary Conditions
A deceleration phase does not necessarily end at unless explicitly stated that the object 'comes to a stop' or 'comes to rest'.
Always underline or circle the given target speed at the end of each phase and convert it to SI units before setting up the area formula.
CORRECTED PATH
ACEpath Teacher's DemonstrationConvert the final velocity of phase 3 to SI units: .
Calculate the displacement for phase 3 using the trapezoid formula: .
Sum the displacements of all three phases: .
(a) ; (b)
03 The student omits the factor of 1/2 for the triangular area in phase 1, treating the phase as if it were traversed at constant maximum speed.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
Because the train uniformly accelerates from rest to , the region under the graph is a triangle, requiring a factor of (or the average velocity ). Omitting treats phase 1 as if the train traveled at top speed the entire time.
- Step 3
- Step 4
- Step 5Correct
Your summation method was correct, but your total value inherited the error from .
WHAT YOU DID WELL
Compliments from Your TeacherYou performed all unit conversions between , , and SI units flawlessly.
You correctly calculated the slope to find the acceleration in phase 1.
You recognized and applied the trapezoid formula correctly in phase 3.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou used instead of during the linear acceleration phase.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou temporarily conflated the displacement formula for constant speed () with the displacement formula for uniform acceleration from rest ( or ).
REASONING PATH
Your ACEpath teacher’s suggested approach- Geometry of Area Under v-t Graphs
For uniform linear acceleration starting from rest, the shape under the velocity-time graph is a triangle, so .
Always sketch or visualize each geometric partition of the graph before multiplying numbers to confirm whether it is a rectangle, triangle, or trapezoid.
CORRECTED PATH
ACEpath Teacher's DemonstrationRecalculate the phase 1 area using the triangle area formula: .
Sum the three segment displacements: .
(a) ; (b)
Lock it in
Why must time given in minutes be converted to seconds before calculating acceleration in ?
Because acceleration is defined as . Dividing by minutes yields , not the standard SI unit ().
Similar question
A subway train accelerates uniformly from rest to over a duration of . Determine its acceleration in .
Answer
(or ). Key steps: ; ; .
A high-speed train travels along a straight track at a constant velocity of for . Calculate the train's total displacement in meters.
Answer
. Key steps: ; ; .
A locomotive slows down uniformly from to over an interval of . Determine: (a) the acceleration in , and (b) the distance covered during this braking phase in meters.
Answer
(a) (or ); (b) . Key steps: , , ; ; .