Resources

A cylindrical metal-film resistor is rated for a maximum continuous power dissipation of Pmax⁡=0.500 WP_{\max} = 0.500\ \text{W} and has an electrical resistance of R=820 ΩR = 820\ \Omega. Any operational state exceeding this threshold leads to thermal failure. (a) Calculate the critical threshold voltage VcritV_{\text{crit}} that can be applied across the resistor before exceeding its rated power limit. (b) Determine the maximum electrical energy Emax⁡E_{\max} that can be safely dissipated by this resistor in Δt=5.00 min\Delta t = 5.00\ \text{min} without exceeding its rated continuous power.

Answer and steps

Final answer

(a) Vcrit=20.2 VV_{\text{crit}} = 20.2\ \text{V}; (b) Emax⁡=150 JE_{\max} = 150\ \text{J}

Steps

Part (a): Critical Threshold Voltage VcritV_{\text{crit}}

  1. Relate electrical power to voltage and resistance: The electrical power PP dissipated across an ohmic resistor of resistance RR under an applied potential difference VV is given by Joule's law: P=V2RP = \frac{V^2}{R}
  2. Express the critical voltage: To remain within safe operating conditions, the dissipated power must not exceed the maximum rated power limit Pmax⁡P_{\max}. The critical voltage VcritV_{\text{crit}} corresponds to this maximum power threshold: Pmax⁡=Vcrit2R  ⟹  Vcrit=Pmax⁡⋅RP_{\max} = \frac{V_{\text{crit}}^2}{R} \implies V_{\text{crit}} = \sqrt{P_{\max} \cdot R}
  3. Substitute the given values: Vcrit=0.500 W⋅820 Ω=410 V2≈20.248 VV_{\text{crit}} = \sqrt{0.500\ \text{W} \cdot 820\ \Omega} = \sqrt{410\ \text{V}^2} \approx 20.248\ \text{V} Rounding to three significant figures gives: Vcrit≈20.2 VV_{\text{crit}} \approx 20.2\ \text{V}

Part (b): Maximum Safe Dissipated Energy Emax⁡E_{\max}

  1. Convert the time interval into SI units: Electrical energy is defined as power multiplied by time when power is continuous and constant. The given time duration must be converted from minutes to seconds: Δt=5.00 min=5.00⋅60 s=300 s\Delta t = 5.00\ \text{min} = 5.00 \cdot 60\ \text{s} = 300\ \text{s}
  2. Calculate the total energy: The maximum rate of energy dissipation is Pmax⁡P_{\max}. The total energy Emax⁡E_{\max} dissipated over duration Δt\Delta t at this continuous rating is: Emax⁡=Pmax⁡⋅ΔtE_{\max} = P_{\max} \cdot \Delta t Emax⁡=0.500 W⋅300 s=150 JE_{\max} = 0.500\ \text{W} \cdot 300\ \text{s} = 150\ \text{J}

Pitfall Note: Remember to convert the operating time into seconds before multiplying by power in watts (W=J/s\text{W} = \text{J/s}), as using minutes directly would yield incorrect units.

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student forgets to take the square root when solving for voltage from P = V²/R, equating V directly to P · R.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    P=V2R  ⟹  V2=0.500⋅820P = \frac{V^2}{R} \implies V^2 = 0.500 \cdot 820

  2. Step 2

    V=410 VV = 410\text{ V}

    Correct

    Vcrit=410 V2≈20.2 VV_{\text{crit}} = \sqrt{410\text{ V}^2} \approx 20.2\text{ V}

    You equated VV directly to the product P⋅RP \cdot R instead of taking the square root of V2=410V^2 = 410.

  3. Step 3

    Δt=5.00⋅60=300 s\Delta t = 5.00 \cdot 60 = 300\text{ s}

  4. Step 4

    Emax⁡=P⋅Δt=0.500⋅300  ⟹  Emax⁡=150 JE_{\max} = P \cdot \Delta t = 0.500 \cdot 300 \implies E_{\max} = 150\text{ J}

WHAT YOU DID WELL
Compliments from Your Teacher

You selected the exact formula P=V2RP = \frac{V^2}{R} that relates power directly to voltage and resistance.

You performed the unit conversion from minutes to seconds accurately for part (b).

You calculated the energy dissipation Emax⁡=150 JE_{\max} = 150\text{ J} correctly.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Omitted Square Root in Algebraic Inversion

You calculated V2=410V^2 = 410 correctly, but recorded the final voltage as 410 V410\text{ V} without executing the final square root operation.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Treating an intermediate evaluation of an isolated squared variable (V2V^2) as the linear variable itself (VV) when transitioning from substitution to the final numerical value.

REASONING PATH
Your ACEpath teacher’s suggested approach
Variable Exponent Tracking
  • When solving y=x2/ky = x^2 / k for xx, isolating the term gives x2=y⋅kx^2 = y \cdot k, which requires x=y⋅kx = \sqrt{y \cdot k}.

  • Circle or highlight the exponent on the unknown variable before writing the next line so you do not omit the radical step.

Sanity Check via Reverse Substitution
  • Plugging your result back into the original formula must reproduce the original given value.

  • Check: (410 V)2820 Ω=205 W≠0.500 W\frac{(410\text{ V})^2}{820\ \Omega} = 205\text{ W} \neq 0.500\text{ W}. This immediately reveals that the voltage is much too large.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Take the principal square root of both sides: Vcrit=410 V2V_{\text{crit}} = \sqrt{410\text{ V}^2}

  2. Evaluate the numerical value: Vcrit≈20.248 VV_{\text{crit}} \approx 20.248\text{ V}

  3. Round to three significant figures: Vcrit≈20.2 VV_{\text{crit}} \approx 20.2\text{ V}

Final answer

(a) Vcrit=20.2 VV_{\text{crit}} = 20.2\text{ V}; (b) Emax⁡=150 JE_{\max} = 150\text{ J}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the relation between power, voltage, and current to ensure fluent algebraic rearrangements of P=V2/RP = V^2 / R and P=I2RP = I^2 R.

  • Practice checking whether your calculated answer has the correct physical order of magnitude before moving on.

OverviewACEpath Teacher's Diagnosis

02 The student fails to convert the time interval from minutes to seconds, substituting 5.00 directly into E = P · Δt.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    P=V2R  ⟹  Vcrit=P⋅R=0.500⋅820  ⟹  Vcrit=410≈20.2 VP = \frac{V^2}{R} \implies V_{\text{crit}} = \sqrt{P \cdot R} = \sqrt{0.500 \cdot 820} \implies V_{\text{crit}} = \sqrt{410} \approx 20.2\text{ V}

  2. Step 2

    Emax⁡=Pmax⁡⋅Δt  ⟹  Emax⁡=0.500⋅5.00=2.50 JE_{\max} = P_{\max} \cdot \Delta t \implies E_{\max} = 0.500 \cdot 5.00 = 2.50\text{ J}

    Correct

    Δt=5.00 min=300 s  ⟹  Emax⁡=0.500 W⋅300 s=150 J\Delta t = 5.00\text{ min} = 300\text{ s} \implies E_{\max} = 0.500\text{ W} \cdot 300\text{ s} = 150\text{ J}

    Because one watt is defined as one joule per second (1 W=1 J/s1\text{ W} = 1\text{ J/s}), the operating time must be converted from minutes into seconds (Δt=5.00 min×60 s/min=300 s\Delta t = 5.00\text{ min} \times 60\text{ s/min} = 300\text{ s}) before computing the energy.

WHAT YOU DID WELL
Compliments from Your Teacher

You selected the correct power equation P=V2RP = \frac{V^2}{R} and solved for the critical voltage accurately.

You identified the relationship between energy, power, and elapsed time E=P⋅ΔtE = P \cdot \Delta t.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Unit conversion omitted

You substituted the elapsed time directly in minutes rather than converting it to SI base units (seconds).

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Overlooking the definition of the watt as J/s\text{J/s}, which requires time to be in seconds for the resulting energy to be in joules.

REASONING PATH
Your ACEpath teacher’s suggested approach
Match units to standard definitions
  • Electrical power in watts corresponds to energy per unit time in seconds: 1 W=1 J/s1\text{ W} = 1\text{ J/s}.

  • Always convert minutes or hours into seconds before calculating energy in joules via E=PΔtE = P \Delta t.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Convert elapsed time to seconds: Δt=5.00 min×60 s/min=300 s\Delta t = 5.00\text{ min} \times 60\text{ s/min} = 300\text{ s}.

  2. Multiply rated continuous power by the converted time: Emax⁡=0.500 W×300 s=150 JE_{\max} = 0.500\text{ W} \times 300\text{ s} = 150\text{ J}.

Final answer

Emax⁡=150 JE_{\max} = 150\text{ J}

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice checking whether time units match the denominator of the rate quantity before performing any multiplication.

  • Write out explicit unit labels alongside numbers in your intermediate steps to catch unit mismatches early.

OverviewACEpath Teacher's Diagnosis

03 The student misremembers the electric power relation as P = V/R instead of P = V²/R, leading to an incorrect voltage threshold.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    P=VR  ⟹  Vcrit=P⋅RP = \frac{V}{R} \implies V_{\text{crit}} = P \cdot R

    Correct

    P=V2R  ⟹  Vcrit=Pmax⁡⋅RP = \frac{V^2}{R} \implies V_{\text{crit}} = \sqrt{P_{\max} \cdot R}

    You set the power equal to VR\frac{V}{R}, which confuses Ohm's law (I=VRI = \frac{V}{R}) with Joule's law. Because power is P=VI=V2RP = V I = \frac{V^2}{R}, the voltage depends on the square root of the power-resistance product.

  2. Step 2

    Vcrit=0.500⋅820=410 VV_{\text{crit}} = 0.500 \cdot 820 = 410\text{ V}

    Correct

    Vcrit=0.500 W⋅820 Ω≈20.2 VV_{\text{crit}} = \sqrt{0.500\text{ W} \cdot 820\ \Omega} \approx 20.2\text{ V}

    You multiplied the values correctly based on your equation, but the numerical result is affected by the missing square root from the power formula.

  3. Step 3

    Δt=5.00⋅60 s=300 s\Delta t = 5.00 \cdot 60\text{ s} = 300\text{ s}

  4. Step 4

    Emax⁡=P⋅Δt=0.500⋅300=150 JE_{\max} = P \cdot \Delta t = 0.500 \cdot 300 = 150\text{ J}

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly converted the operational time interval from minutes to seconds.

You accurately applied the relationship between power, time, and total energy in Part (b).

You showed clean, orderly algebraic steps throughout your work.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Formula confusion (Ohm's law vs. Joule's power law)

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You recalled P=VRP = \frac{V}{R} instead of combining Joule's law P=VIP = V I with Ohm's law I=VRI = \frac{V}{R}, which yields P=V2RP = \frac{V^2}{R}. Without the square term, the formula represents current rather than power.

REASONING PATH
Your ACEpath teacher’s suggested approach
Recall the fundamental definitions
  • Ohm's law is V=IRV = I R (or I=VRI = \frac{V}{R}), whereas electric power is always P=VIP = V I.

  • Derive the power formula in terms of VV and RR by substituting I=VRI = \frac{V}{R} into P=VIP = V I to get P=V(VR)=V2RP = V\left(\frac{V}{R}\right) = \frac{V^2}{R}.

Check physical units
  • The ratio VΩ\frac{\text{V}}{\Omega} equals amperes (current), not watts (power).

  • Always verify that the units of your target expression match: V2Ω=W\frac{\text{V}^2}{\Omega} = \text{W}.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Start from Joule's dissipation law: P=V2RP = \frac{V^2}{R}.

  2. Isolate the critical threshold voltage: V2=Pmax⁡⋅R  ⟹  Vcrit=Pmax⁡⋅RV^2 = P_{\max} \cdot R \implies V_{\text{crit}} = \sqrt{P_{\max} \cdot R}.

  3. Substitute the given ratings: Vcrit=0.500 W⋅820 Ω=410≈20.248 VV_{\text{crit}} = \sqrt{0.500\text{ W} \cdot 820\ \Omega} = \sqrt{410} \approx 20.248\text{ V}.

  4. Round to three significant figures: Vcrit≈20.2 VV_{\text{crit}} \approx 20.2\text{ V}.

Final answer

(a) Vcrit=20.2 VV_{\text{crit}} = 20.2\text{ V}; (b) Emax⁡=150 JE_{\max} = 150\text{ J}

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice deriving the three forms of electric power (P=VI=I2R=V2RP = VI = I^2 R = \frac{V^2}{R}) before each problem.

  • Check your formulas dimensionally to ensure you never confuse current (I=VRI = \frac{V}{R}) with power (P=V2RP = \frac{V^2}{R}).

Lock it in

Similar question

01

A 2.00 kΩ2.00\ \text{k}\Omega resistor has a maximum continuous power rating of 0.250 W0.250\text{ W}. Calculate the maximum voltage that can be applied across it without damage.

Answer

Vmax⁡=22.4 VV_{\max} = 22.4\text{ V}. Key step: Vmax⁡=Pmax⁡⋅R=0.250 W⋅2000 Ω=500≈22.36 V≈22.4 VV_{\max} = \sqrt{P_{\max} \cdot R} = \sqrt{0.250\text{ W} \cdot 2000\ \Omega} = \sqrt{500} \approx 22.36\text{ V} \approx 22.4\text{ V}.

02

A circuit component with resistance R=50.0 ΩR = 50.0\ \Omega operates at its rated voltage limit of V=15.0 VV = 15.0\text{ V}. (a) Find its operating power PP. (b) Determine how much energy it dissipates in 2.00 minutes2.00\text{ minutes}.

Answer

(a) P=4.50 WP = 4.50\text{ W}; (b) E=540 JE = 540\text{ J}. Key steps: (a) P=V2R=15.0250.0=4.50 WP = \frac{V^2}{R} = \frac{15.0^2}{50.0} = 4.50\text{ W}. (b) Δt=2.00⋅60=120 s\Delta t = 2.00 \cdot 60 = 120\text{ s}, so E=P⋅Δt=4.50⋅120=540 JE = P \cdot \Delta t = 4.50 \cdot 120 = 540\text{ J}.

03

A heating element is rated for Prated=1200 WP_{\text{rated}} = 1200\text{ W} at Vrated=120 VV_{\text{rated}} = 120\text{ V}. If the available supply voltage drops to 108 V108\text{ V} (a 10%10\% drop), assuming resistance remains constant, find the new power output and the energy delivered in 10.0 minutes10.0\text{ minutes}.

Answer

Pnew=972 WP_{\text{new}} = 972\text{ W}; E=5.83×105 JE = 5.83 \times 10^5\text{ J} (or 583 kJ583\text{ kJ}). Key steps: Resistance R=Vrated2Prated=12021200=12.0 ΩR = \frac{V_{\text{rated}}^2}{P_{\text{rated}}} = \frac{120^2}{1200} = 12.0\ \Omega. New power Pnew=108212.0=972 WP_{\text{new}} = \frac{108^2}{12.0} = 972\text{ W}. Energy E=972 W⋅(10.0×60 s)=583,200 J≈5.83×105 JE = 972\text{ W} \cdot (10.0 \times 60\text{ s}) = 583{,}200\text{ J} \approx 5.83 \times 10^5\text{ J}.

Loading workspace…