Resources

An industrial high-shear mixer operates at a designated rotation speed of 3450 rpm3450\text{ rpm}. (a) Convert this operational speed to rotational frequency ff in millihertz (mHz\text{mHz}). (b) Calculate the period of rotation TT in milliseconds (ms\text{ms}).

Answer and steps

Final answer

(a) f=5.75×104 mHzf = 5.75 \times 10^4\text{ mHz}; (b) T=17.4 msT = 17.4\text{ ms}

Steps

Part (a): Determine the Rotational Frequency in Millihertz (mHz\text{mHz})

  1. Convert revolutions per minute (rpm\text{rpm}) to hertz (Hz\text{Hz}): Frequency ff represents the number of complete revolutions per second. Since 1 minute=60 seconds1\text{ minute} = 60\text{ seconds}: f=3450 revolutions1 minute=3450 rev60 s=57.5 Hzf = \frac{3450\text{ revolutions}}{1\text{ minute}} = \frac{3450\text{ rev}}{60\text{ s}} = 57.5\text{ Hz}
  2. Convert hertz (Hz\text{Hz}) to millihertz (mHz\text{mHz}): The metric prefix milli- (m\text{m}) corresponds to 10−310^{-3}, which means 1 Hz=103 mHz=1000 mHz1\text{ Hz} = 10^3\text{ mHz} = 1000\text{ mHz}. f=57.5 Hz×103 mHz1 Hz=57 500 mHz=5.75×104 mHzf = 57.5\text{ Hz} \times \frac{10^3\text{ mHz}}{1\text{ Hz}} = 57\,500\text{ mHz} = 5.75 \times 10^4\text{ mHz}

    Pitfall: Be careful not to confuse the lowercase prefix m\text{m} (milli-, 10−310^{-3}) with the uppercase prefix M\text{M} (mega-, 10610^6).


Part (b): Calculate the Period of Rotation in Milliseconds (ms\text{ms})

  1. Relate period TT to frequency ff: The period TT is the time required to complete one full revolution, which is the reciprocal of the frequency: T=1fT = \frac{1}{f}
  2. Calculate TT in seconds: Using the frequency in standard SI units (f=57.5 Hzf = 57.5\text{ Hz}): T=157.5 s−1≈0.017391 sT = \frac{1}{57.5\text{ s}^{-1}} \approx 0.017391\text{ s}
  3. Convert seconds (s\text{s}) to milliseconds (ms\text{ms}): Since 1 s=103 ms1\text{ s} = 10^3\text{ ms}: T=0.017391 s×1000mss≈17.4 msT = 0.017391\text{ s} \times 1000\frac{\text{ms}}{\text{s}} \approx 17.4\text{ ms}

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student misinterprets the metric prefix milli as 10⁻⁶ rather than 10⁻³, confusing it with micro and leading to an incorrect frequency.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    f=57.5 Hzf = 57.5\text{ Hz}

  2. Step 2

    f=57.5×106 mHz=57500000 mHzf = 57.5 \times 10^6\text{ mHz} = 57500000\text{ mHz}

    Correct

    f=57.5×103 mHz=5.75×104 mHzf = 57.5 \times 10^3\text{ mHz} = 5.75 \times 10^4\text{ mHz}

    You multiplied by 10610^6 rather than 10310^3. The prefix milli- (m\text{m}) denotes 10−310^{-3}, so 1 Hz=103 mHz=1000 mHz1\text{ Hz} = 10^3\text{ mHz} = 1000\text{ mHz}, whereas 10610^6 corresponds to micro- (μ\mu) or mega- (M\text{M}).

  3. Step 3

    T=157.5 s≈0.01739 s  ⟹  T=0.01739×1000 ms≈17.39 msT = \frac{1}{57.5}\text{ s} \approx 0.01739\text{ s} \implies T = 0.01739 \times 1000\text{ ms} \approx 17.39\text{ ms}

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly converted rotational speed from rpm\text{rpm} to Hz\text{Hz} by dividing by 6060.

You correctly applied the relationship T=1fT = \frac{1}{f} to find the rotational period.

You accurately converted seconds to milliseconds using the factor of 10001000 in part (b).

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Metric Prefix Misidentification

You substituted 10610^6 instead of 10310^3 when converting from base hertz to millihertz.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You confused the prefix milli- (m\text{m}, representing 10−310^{-3}) with micro- (μ\mu, representing 10−610^{-6}) or mega- (M\text{M}, representing 10610^6) during the frequency unit conversion.

REASONING PATH
Your ACEpath teacher’s suggested approach
SI Prefix Scaling
  • The metric prefix milli- (m\text{m}) always represents a factor of 10−310^{-3}, meaning 1 base unit=103 milli-units=1000 milli-units1\text{ base unit} = 10^3\text{ milli-units} = 1000\text{ milli-units}.

  • Whenever you convert a base unit to a milli-unit, multiply by 10310^3 (or 10001000), not 10610^6.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. f=57.5 Hz×103 mHz1 Hz=57 500 mHz=5.75×104 mHzf = 57.5\text{ Hz} \times \frac{10^3\text{ mHz}}{1\text{ Hz}} = 57\,500\text{ mHz} = 5.75 \times 10^4\text{ mHz}

Final answer

(a) f=5.75×104 mHzf = 5.75 \times 10^4\text{ mHz}; (b) T≈17.4 msT \approx 17.4\text{ ms}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the standard metric prefixes from mega- (10610^6) down to micro- (10−610^{-6}) to keep lowercase m\text{m} (milli-) distinct from μ\mu (micro-) and uppercase M\text{M} (mega-).

  • Always perform a quick sanity check: since a millihertz is smaller than a hertz, there must be exactly 10001000 millihertz in one hertz, just as there are 10001000 milliseconds in one second.

OverviewACEpath Teacher's Diagnosis

02 The student multiplies by 60 instead of dividing by 60 when converting revolutions per minute to revolutions per second (Hz).

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    f=3450×60 Hz=207000 Hzf = 3450 \times 60\text{ Hz} = 207000\text{ Hz}

    Correct

    f=3450 rev60 s=57.5 Hzf = \frac{3450\text{ rev}}{60\text{ s}} = 57.5\text{ Hz}

    One minute equals 60 seconds60\text{ seconds}, so a machine completing 3450 revolutions3450\text{ revolutions} in a full minute completes 345060=57.5 revolutions\frac{3450}{60} = 57.5\text{ revolutions} each second. Dividing by 6060, rather than multiplying, gives the frequency in hertz.

  2. Step 2

    f=207000×1000 mHz=207000000 mHzf = 207000 \times 1000\text{ mHz} = 207000000\text{ mHz}

    Correct

    f=57.5×1000 mHz=5.75×104 mHzf = 57.5 \times 1000\text{ mHz} = 5.75 \times 10^4\text{ mHz}

    Your conversion factor (1 Hz=1000 mHz1\text{ Hz} = 1000\text{ mHz}) was set up correctly, but the resulting value is inaccurate due to the earlier frequency error.

  3. Step 3

    T=1207000 s≈4.83×10−6 sT = \frac{1}{207000}\text{ s} \approx 4.83 \times 10^{-6}\text{ s}

    Correct

    T=157.5 Hz≈0.01739 sT = \frac{1}{57.5\text{ Hz}} \approx 0.01739\text{ s}

    You correctly used the reciprocal relationship T=1fT = \frac{1}{f}, but substituting the incorrect frequency value carried the error forward.

  4. Step 4

    T=4.83×10−6×1000 ms≈0.00483 msT = 4.83 \times 10^{-6} \times 1000\text{ ms} \approx 0.00483\text{ ms}

    Correct

    T=0.01739 s×1000mss≈17.4 msT = 0.01739\text{ s} \times 1000\frac{\text{ms}}{\text{s}} \approx 17.4\text{ ms}

    Your conversion from seconds to milliseconds correctly multiplied by 10001000, but the numerical value was affected by the previous steps.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified and applied the reciprocal formula between period and frequency, T=1fT = \frac{1}{f}.

You used the correct metric prefix conversion factor of 10001000 to convert hertz to millihertz and seconds to milliseconds.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Rate unit conversion error

You set up the rate conversion as 3450×603450 \times 60 instead of dividing by 60 s/min60\text{ s/min}.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing how time units convert when time is in the denominator of a rate: while 1 min=60 s1\text{ min} = 60\text{ s}, converting from per-minute to per-second requires dividing by 6060 because each second contains only 160\frac{1}{60} of the minute's total revolutions.

REASONING PATH
Your ACEpath teacher’s suggested approach
Dimensional Analysis Check
  • Write rotational speed with explicit units: rpm=revmin\text{rpm} = \frac{\text{rev}}{\text{min}} and 1 min=60 s1\text{ min} = 60\text{ s}.

  • Multiply by the unit factor 1 min60 s\frac{1\text{ min}}{60\text{ s}} so that the minute units cancel out in the denominator.

Sanity Check on Rates
  • A process completes fewer cycles in a single second than in a full 60-second60\text{-second} minute.

  • Ensure that the numerical value in hertz (rev/s\text{rev/s}) is smaller than the value in rpm\text{rpm} by a factor of 6060.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Divide by 6060 to obtain standard frequency: f=3450 rev/min60 s/min=57.5 Hzf = \frac{3450\text{ rev/min}}{60\text{ s/min}} = 57.5\text{ Hz}.

  2. Multiply by 10310^3 to convert to millihertz: f=57.5 Hz×1000mHzHz=5.75×104 mHzf = 57.5\text{ Hz} \times 1000\frac{\text{mHz}}{\text{Hz}} = 5.75 \times 10^4\text{ mHz}.

  3. Compute period in seconds: T=1f=157.5 s−1≈0.01739 sT = \frac{1}{f} = \frac{1}{57.5\text{ s}^{-1}} \approx 0.01739\text{ s}.

  4. Multiply by 10310^3 to convert to milliseconds: T=0.01739 s×1000mss≈17.4 msT = 0.01739\text{ s} \times 1000\frac{\text{ms}}{\text{s}} \approx 17.4\text{ ms}.

Final answer

(a) f=5.75×104 mHzf = 5.75 \times 10^4\text{ mHz}; (b) T=17.4 msT = 17.4\text{ ms}

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice converting rotational quantities using unit fractions with explicit units (e.g., 1 min60 s\frac{1\text{ min}}{60\text{ s}}) to prevent multiplication/division reversals.

  • Perform a physical intuition check: verify that frequency in hertz is always smaller than rpm, and period TT is reasonably proportional to rotation rate.

OverviewACEpath Teacher's Diagnosis

03 The student divides by 1000 instead of multiplying by 1000 when converting the period from seconds to milliseconds.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    f=345060 Hz=57.5 Hz  ⟹  f=57.5×1000 mHz=57500 mHzf = \frac{3450}{60}\text{ Hz} = 57.5\text{ Hz} \implies f = 57.5 \times 1000\text{ mHz} = 57500\text{ mHz}

  2. Step 2

    T=157.5 s≈0.01739 sT = \frac{1}{57.5}\text{ s} \approx 0.01739\text{ s}

  3. Step 3

    T=0.017391000 ms≈0.00001739 msT = \frac{0.01739}{1000}\text{ ms} \approx 0.00001739\text{ ms}

    Correct

    T=0.01739 s×1000mss≈17.4 msT = 0.01739\text{ s} \times 1000\frac{\text{ms}}{\text{s}} \approx 17.4\text{ ms}

    To convert from seconds to milliseconds, you need to multiply by 10001000 because 1 s=1000 ms1\text{ s} = 1000\text{ ms}. Dividing by 10001000 incorrectly makes the numerical value a thousand times smaller instead of larger.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly divided the speed in rpm by 6060 to obtain the rotational frequency in hertz.

You successfully applied the metric prefix milli- (10−310^{-3}) to convert hertz to millihertz.

You correctly identified that period is the reciprocal of frequency (T=1fT = \frac{1}{f}) and calculated the period in seconds.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Metric prefix unit conversion direction error

You divided by 10001000 instead of multiplying by 10001000 when converting seconds to milliseconds.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusion over whether to multiply or divide when moving from a base SI unit (seconds) to a submultiple metric unit with the milli- prefix (10−310^{-3}). A smaller unit means there must be a larger count of those units for the same physical quantity (1 s=1000 ms1\text{ s} = 1000\text{ ms}).

REASONING PATH
Your ACEpath teacher’s suggested approach
Unit Size vs. Numerical Value Check
  • When converting from a larger unit to a smaller unit, the numerical value must increase.

  • Before writing your final answer, verify that 0.0174 s0.0174\text{ s} contains many milliseconds (17.4 ms17.4\text{ ms}), not a fraction of a microsecond.

Dimensional Analysis Factor Method
  • Multiply by a conversion factor equal to 11, arranging units so the unwanted unit cancels out: value in s×(1000 ms1 s)\text{value in s} \times \left(\frac{1000\text{ ms}}{1\text{ s}}\right).

  • Write out the unit fraction explicitly so the s\text{s} in the numerator cancels with the s\text{s} in the denominator.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Multiply the period in seconds by 1000 ms/s1000\text{ ms/s}: T=0.017391 s×1000mss=17.391 msT = 0.017391\text{ s} \times 1000\frac{\text{ms}}{\text{s}} = 17.391\text{ ms}.

  2. Round to three significant figures to match the given data: T≈17.4 msT \approx 17.4\text{ ms}.

Final answer

(a) f=5.75×104 mHzf = 5.75 \times 10^4\text{ mHz}; (b) T=17.4 msT = 17.4\text{ ms}

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice unit conversions using explicit unit-factor cancellation fractions rather than doing mental division/multiplication.

  • Review standard metric prefixes (milli- =10−3= 10^{-3}, micro- =10−6= 10^{-6}, kilo- =103= 10^3) and remember that smaller units require larger numbers to represent the same amount of time.

Lock it in

Similar question

01

A laboratory centrifuge rotates at a constant speed of 1800 rpm1800\text{ rpm}. (a) Determine its rotational frequency in millihertz (mHz\text{mHz}). (b) Find its period of rotation in milliseconds (ms\text{ms}).

Answer

(a) f=180060 Hz=30 Hz=30×103 mHz=3.0×104 mHzf = \frac{1800}{60}\text{ Hz} = 30\text{ Hz} = 30 \times 10^3\text{ mHz} = 3.0 \times 10^4\text{ mHz}. (b) T=130 s≈0.0333 s=33.3 msT = \frac{1}{30}\text{ s} \approx 0.0333\text{ s} = 33.3\text{ ms}.

02

An optical chopper disc completes one full revolution every 12.5 ms12.5\text{ ms}. Calculate: (a) the rotational frequency in hertz (Hz\text{Hz}); (b) the operational rotation speed in revolutions per minute (rpm\text{rpm}).

Answer

(a) T=12.5×10−3 s=0.0125 sT = 12.5 \times 10^{-3}\text{ s} = 0.0125\text{ s}. Then f=1T=10.0125 s=80 Hzf = \frac{1}{T} = \frac{1}{0.0125\text{ s}} = 80\text{ Hz}. (b) Speed=80 rev/s×60 s/min=4800 rpm\text{Speed} = 80\text{ rev/s} \times 60\text{ s/min} = 4800\text{ rpm}.

03

A high-speed dental turbine spindle operates at 120 krpm120\text{ krpm} (120,000 rpm120{,}000\text{ rpm}). Compute its rotational frequency in kilohertz (kHz\text{kHz}) and its period of rotation in microseconds (μs\mu\text{s}).

Answer
  1. Frequency in hertz: f=120,00060 Hz=2000 Hz=2.0 kHzf = \frac{120\text{,000}}{60}\text{ Hz} = 2000\text{ Hz} = 2.0\text{ kHz}.
  2. Period: T=12000 Hz=0.0005 s=500 μsT = \frac{1}{2000\text{ Hz}} = 0.0005\text{ s} = 500\text{ }\mu\text{s}.
Loading workspace…