Resources

In a resonance tube experiment used to measure the speed of sound in air, a graduated glass cylinder partially filled with water acts as a pipe closed at the bottom by the water surface. A tuning fork vibrating at f=512 Hzf = 512\text{ Hz} is held over the top open rim. As the water level is lowered continuously from the top rim, the first resonance is observed at an air-column length of L1=15.2 cmL_1 = 15.2\text{ cm}, and the second resonance is observed at L2=48.4 cmL_2 = 48.4\text{ cm}. Using the two-resonance end-correction method, calculate the acoustic end-correction factor ΔL=c⋅r\Delta L = c \cdot r of the tube and determine the experimental speed of sound vv in air.

Answer and steps

Final answer

End correction: ΔL=1.40 cm\Delta L = 1.40\text{ cm} (or 0.0140 m0.0140\text{ m}); Speed of sound: v=340 m/sv = 340\text{ m/s}

Steps

01

Relate the Resonant Lengths to Wavelength

Understanding the Standing Wave in a Resonance Tube

A tube closed at one end by water and open at the other end supports standing sound waves with a displacement node at the water surface and a displacement antinode slightly above the open top. Because the antinode forms a small distance ΔL\Delta L outside the rim of the tube, the effective length of the vibrating air column is greater than the measured physical length: Leff=L+ΔLL_{\text{eff}} = L + \Delta L where:

  • LL is the measured length of the air column inside the tube,
  • ΔL\Delta L is the acoustic end correction.

The resonance conditions for the first two modes of a tube closed at one end are:

  1. First resonance (fundamental mode, quarter-wavelength): L1+ΔL=λ4L_1 + \Delta L = \frac{\lambda}{4}
  2. Second resonance (next harmonic, three quarter-wavelengths): L2+ΔL=3λ4L_2 + \Delta L = \frac{3\lambda}{4}

Subtracting the first equation from the second eliminates the unknown end correction ΔL\Delta L:

(L2+ΔL)−(L1+ΔL)=3λ4−λ4(L_2 + \Delta L) - (L_1 + \Delta L) = \frac{3\lambda}{4} - \frac{\lambda}{4}

L2−L1=λ2L_2 - L_1 = \frac{\lambda}{2}


02

Calculate the Wavelength (λ\lambda) and Speed of Sound (vv)

Substitute the given measured lengths L1=15.2 cmL_1 = 15.2\text{ cm} and L2=48.4 cmL_2 = 48.4\text{ cm}:

λ2=48.4 cm−15.2 cm=33.2 cm\frac{\lambda}{2} = 48.4\text{ cm} - 15.2\text{ cm} = 33.2\text{ cm}

λ=2⋅33.2 cm=66.4 cm=0.664 m\lambda = 2 \cdot 33.2\text{ cm} = 66.4\text{ cm} = 0.664\text{ m}

Using the wave speed equation v=fλv = f\lambda with the tuning fork frequency f=512 Hzf = 512\text{ Hz}:

v=512 Hz⋅0.664 m=339.968 m/s≈340 m/sv = 512\text{ Hz} \cdot 0.664\text{ m} = 339.968\text{ m/s} \approx 340\text{ m/s}


03

Determine the End Correction (ΔL\Delta L)

Substitute λ=66.4 cm\lambda = 66.4\text{ cm} into the equation for the first resonance:

ΔL=λ4−L1\Delta L = \frac{\lambda}{4} - L_1

ΔL=66.4 cm4−15.2 cm=16.6 cm−15.2 cm=1.40 cm\Delta L = \frac{66.4\text{ cm}}{4} - 15.2\text{ cm} = 16.6\text{ cm} - 15.2\text{ cm} = 1.40\text{ cm}

In standard SI units:

ΔL=0.0140 m\Delta L = 0.0140\text{ m}

(Pitfall note: A common mistake is calculating the wavelength directly as λ=4L1\lambda = 4L_1, ignoring the end correction. Because ΔL\Delta L is significant, relying on a single length yields an inaccurate wavelength and sound speed.)

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student misremembers the end-correction formula by subtracting the resonance lengths in the numerator without multiplying L₁ by 3, resulting in an overestimated end correction.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    λ2=L2−L1=48.4 cm−15.2 cm=33.2 cm  ⟹  λ=66.4 cm\frac{\lambda}{2} = L_2 - L_1 = 48.4\text{ cm} - 15.2\text{ cm} = 33.2\text{ cm} \implies \lambda = 66.4\text{ cm}

  2. Step 2

    ΔL=L2−L12=48.4 cm−15.2 cm2=16.6 cm\Delta L = \frac{L_2 - L_1}{2} = \frac{48.4\text{ cm} - 15.2\text{ cm}}{2} = 16.6\text{ cm}

    Correct

    ΔL=L2−3L12=48.4 cm−3(15.2 cm)2=1.40 cm\Delta L = \frac{L_2 - 3L_1}{2} = \frac{48.4\text{ cm} - 3(15.2\text{ cm})}{2} = 1.40\text{ cm}

    You calculated L2−L12\frac{L_2 - L_1}{2}, which equals λ4=L1+ΔL\frac{\lambda}{4} = L_1 + \Delta L, rather than the end correction ΔL\Delta L alone. Because L1+ΔL=λ4L_1 + \Delta L = \frac{\lambda}{4} and L2+ΔL=3λ4=3(L1+ΔL)L_2 + \Delta L = \frac{3\lambda}{4} = 3(L_1 + \Delta L), eliminating λ\lambda yields ΔL=L2−3L12\Delta L = \frac{L_2 - 3L_1}{2} (or ΔL=λ4−L1=16.6 cm−15.2 cm=1.40 cm\Delta L = \frac{\lambda}{4} - L_1 = 16.6\text{ cm} - 15.2\text{ cm} = 1.40\text{ cm}).

  3. Step 3

    v=f⋅λ=512 Hz×0.664 m=340 m/sv = f \cdot \lambda = 512\text{ Hz} \times 0.664\text{ m} = 340\text{ m/s}

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly related the difference between consecutive resonant lengths to half a wavelength (L2−L1=λ2L_2 - L_1 = \frac{\lambda}{2}).

You accurately converted the wavelength to meters and calculated the speed of sound using v=fλv = f\lambda.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Formula Misapplication

You evaluated L2−L12\frac{L_2 - L_1}{2}, which is actually the quarter-wavelength λ4\frac{\lambda}{4}, and labeled it as ΔL\Delta L.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You confused the effective quarter-wavelength L1+ΔL=λ4L_1 + \Delta L = \frac{\lambda}{4} with the end correction ΔL\Delta L alone, or misremembered the formula ΔL=L2−3L12\Delta L = \frac{L_2 - 3L_1}{2} by omitting the coefficient of 33 before L1L_1.

REASONING PATH
Your ACEpath teacher’s suggested approach
Fundamental Resonance Boundary Condition
  • For a pipe closed at one end, the effective length of the fundamental mode is L1+ΔL=λ4L_1 + \Delta L = \frac{\lambda}{4}.

  • Always find ΔL\Delta L by subtracting the physical length L1L_1 from the quarter-wavelength: ΔL=λ4−L1\Delta L = \frac{\lambda}{4} - L_1.

Elimination Formula for End Correction
  • Since L2+ΔL=3(L1+ΔL)L_2 + \Delta L = 3(L_1 + \Delta L), subtracting 3L13L_1 from L2L_2 leaves 2ΔL2\Delta L.

  • Verify that your algebraic formula has L2−3L1L_2 - 3L_1 in the numerator, yielding ΔL=L2−3L12\Delta L = \frac{L_2 - 3L_1}{2}.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Use the fundamental resonance relation: L1+ΔL=λ4L_1 + \Delta L = \frac{\lambda}{4}.

  2. Substitute λ=66.4 cm\lambda = 66.4\text{ cm} and L1=15.2 cmL_1 = 15.2\text{ cm}: ΔL=66.4 cm4−15.2 cm=16.6 cm−15.2 cm=1.40 cm\Delta L = \frac{66.4\text{ cm}}{4} - 15.2\text{ cm} = 16.6\text{ cm} - 15.2\text{ cm} = 1.40\text{ cm}.

Final answer

ΔL=1.40 cm\Delta L = 1.40\text{ cm} (or 0.0140 m0.0140\text{ m}), v=340 m/sv = 340\text{ m/s}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review how the standing wave antinode extends slightly past the physical tube opening by distance ΔL\Delta L.

  • Practice deriving ΔL\Delta L directly from the two system equations rather than relying on memorized numerator formulas.

OverviewACEpath Teacher's Diagnosis

02 The student assumes the open pipe condition λ/2 for the fundamental resonance instead of a closed pipe's λ/4, leading to a halved calculated wavelength and sound speed.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    L2−L1=λ  ⟹  λ=48.4 cm−15.2 cm=33.2 cmL_2 - L_1 = \lambda \implies \lambda = 48.4\text{ cm} - 15.2\text{ cm} = 33.2\text{ cm}

    Correct

    L2−L1=λ2  ⟹  λ=2(48.4 cm−15.2 cm)=66.4 cm=0.664 mL_2 - L_1 = \frac{\lambda}{2} \implies \lambda = 2(48.4\text{ cm} - 15.2\text{ cm}) = 66.4\text{ cm} = 0.664\text{ m}

    In a tube closed at one end, consecutive resonant lengths occur at odd quarter-wavelengths (λ4,3λ4,…\frac{\lambda}{4}, \frac{3\lambda}{4}, \dots). The distance between any two adjacent resonances is the node-to-node spacing, which is half a wavelength (λ2\frac{\lambda}{2}), not a full wavelength.

  2. Step 2

    L1+ΔL=λ2  ⟹  ΔL=33.2 cm2−15.2 cm=1.4 cmL_1 + \Delta L = \frac{\lambda}{2} \implies \Delta L = \frac{33.2\text{ cm}}{2} - 15.2\text{ cm} = 1.4\text{ cm}

    Correct

    L1+ΔL=λ4  ⟹  ΔL=66.4 cm4−15.2 cm=1.40 cmL_1 + \Delta L = \frac{\lambda}{4} \implies \Delta L = \frac{66.4\text{ cm}}{4} - 15.2\text{ cm} = 1.40\text{ cm}

    The effective length for the first resonance in a closed pipe corresponds to a quarter-wavelength (λ4\frac{\lambda}{4}), not a half-wavelength. Although you obtained the correct numerical value of 1.4 cm1.4\text{ cm}, this was a coincidental cancellation because both your wavelength and your harmonic fraction were halved.

  3. Step 3

    v=f⋅λ  ⟹  v=512 Hz×0.332 m=170 m/sv = f \cdot \lambda \implies v = 512\text{ Hz} \times 0.332\text{ m} = 170\text{ m/s}

    Correct

    v=f⋅λ  ⟹  v=512 Hz×0.664 m≈340 m/sv = f \cdot \lambda \implies v = 512\text{ Hz} \times 0.664\text{ m} \approx 340\text{ m/s}

    You correctly applied the wave speed equation v=fλv = f\lambda, but the result was halved due to the incorrect wavelength propagated from part (a).

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly recognized that subtracting the two resonance lengths eliminates the unknown end correction ΔL\Delta L.

You correctly applied the wave speed relation v=fλv = f\lambda with consistent unit conversion from centimeters to meters.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Standing wave boundary condition error in closed pipe

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You applied open-pipe or whole-wave spacing rules instead of closed-pipe boundary conditions. A pipe closed at one end supports standing waves with a displacement node at the closed end and an antinode at the open end, meaning the fundamental mode is Leff=λ4L_{\text{eff}} = \frac{\lambda}{4} and successive resonances are separated by λ2\frac{\lambda}{2}.

REASONING PATH
Your ACEpath teacher’s suggested approach
Consecutive Resonance Spacing
  • The distance between consecutive resonances of the same frequency is always half a wavelength: Ln+1−Ln=λ2L_{n+1} - L_n = \frac{\lambda}{2}.

  • Always equate the difference between consecutive resonant positions to λ2\frac{\lambda}{2} and multiply by 22 to find λ\lambda.

Closed-Pipe Mode Conditions
  • For a pipe closed at one end, resonances occur at odd multiples of a quarter-wavelength: L+ΔL=(2n−1)λ4L + \Delta L = (2n - 1)\frac{\lambda}{4}.

  • Set the first resonance condition to L1+ΔL=λ4L_1 + \Delta L = \frac{\lambda}{4} when solving for the end correction.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Calculate the true wavelength from consecutive resonance spacing: λ2=L2−L1=48.4 cm−15.2 cm=33.2 cm  ⟹  λ=66.4 cm=0.664 m\frac{\lambda}{2} = L_2 - L_1 = 48.4\text{ cm} - 15.2\text{ cm} = 33.2\text{ cm} \implies \lambda = 66.4\text{ cm} = 0.664\text{ m}.

  2. Substitute λ\lambda into the first resonance condition: ΔL=λ4−L1=66.4 cm4−15.2 cm=16.6 cm−15.2 cm=1.40 cm=0.0140 m\Delta L = \frac{\lambda}{4} - L_1 = \frac{66.4\text{ cm}}{4} - 15.2\text{ cm} = 16.6\text{ cm} - 15.2\text{ cm} = 1.40\text{ cm} = 0.0140\text{ m}.

  3. Calculate the experimental speed of sound: v=fλ=512 Hz×0.664 m=339.968 m/s≈340 m/sv = f\lambda = 512\text{ Hz} \times 0.664\text{ m} = 339.968\text{ m/s} \approx 340\text{ m/s}.

Final answer

End correction: ΔL=1.40 cm\Delta L = 1.40\text{ cm} (0.0140 m0.0140\text{ m}); Speed of sound: v=340 m/sv = 340\text{ m/s}

NEXT STEPS
Final Takeaways from Your Teacher
  • Sketch the standing wave pattern showing displacement nodes and antinodes whenever working with acoustic resonance problems.

  • Verify whether your final sound speed in air falls within the physically expected range of approximately 330 m/s330\text{ m/s} to 350 m/s350\text{ m/s} at room temperature.

OverviewACEpath Teacher's Diagnosis

03 The student neglects to convert the wavelength from centimeters to meters before multiplying by frequency in hertz, causing the calculated speed of sound to be off by a factor of 100.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    λ2=L2−L1=48.4 cm−15.2 cm=33.2 cm  ⟹  λ=66.4 cm\frac{\lambda}{2} = L_2 - L_1 = 48.4\text{ cm} - 15.2\text{ cm} = 33.2\text{ cm} \implies \lambda = 66.4\text{ cm}

  2. Step 2

    L1+ΔL=λ4=16.6 cm  ⟹  ΔL=16.6 cm−15.2 cm=1.4 cmL_1 + \Delta L = \frac{\lambda}{4} = 16.6\text{ cm} \implies \Delta L = 16.6\text{ cm} - 15.2\text{ cm} = 1.4\text{ cm}

  3. Step 3

    v=f⋅λ  ⟹  v=512 Hz×66.4 cm=33997 m/sv = f \cdot \lambda \implies v = 512\text{ Hz} \times 66.4\text{ cm} = 33997\text{ m/s}

    Correct

    v=f⋅λ=512 Hz×0.664 m≈340 m/sv = f \cdot \lambda = 512\text{ Hz} \times 0.664\text{ m} \approx 340\text{ m/s}

    You multiplied frequency in Hz\text{Hz} (which is s−1\text{s}^{-1}) by wavelength in cm\text{cm}, which yields a speed in cm/s\text{cm/s}, but you labeled the result as m/s\text{m/s} without dividing by 100100.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly used the difference between consecutive resonance positions, L2−L1=λ2L_2 - L_1 = \frac{\lambda}{2}, to eliminate the end correction.

You accurately solved for the acoustic end correction ΔL=1.4 cm\Delta L = 1.4\text{ cm} using the fundamental resonance relation.

You selected the correct wave speed relation v=fλv = f\lambda.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Unit Conversion Error

You calculated 512×66.4512 \times 66.4 using centimeters and directly attached the unit m/s\text{m/s} instead of cm/s\text{cm/s}.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You omitted explicit unit tracking in the wave speed formula, multiplying an SI frequency (s−1\text{s}^{-1}) by a non-SI length (cm\text{cm}) without converting to base SI units (m\text{m}).

REASONING PATH
Your ACEpath teacher’s suggested approach
Convert lengths to base SI units
  • Before calculating wave speed in m/s\text{m/s}, ensure wavelength is expressed in meters: 1 m=100 cm1\text{ m} = 100\text{ cm}.

  • Convert λ=66.4 cm\lambda = 66.4\text{ cm} to 0.664 m0.664\text{ m} before multiplying by f=512 Hzf = 512\text{ Hz}.

Sanity check physical magnitudes
  • The speed of sound in air at room temperature is approximately 340 m/s340\text{ m/s}.

  • Compare your calculated value of roughly 34000 m/s34000\text{ m/s} with the typical speed of sound to catch factor-of-100 unit slips immediately.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Convert the wavelength to meters: λ=66.4 cm=0.664 m\lambda = 66.4\text{ cm} = 0.664\text{ m}.

  2. Calculate the speed of sound using SI units: v=fλ=512 s−1×0.664 m=339.968 m/s≈340 m/sv = f\lambda = 512\text{ s}^{-1} \times 0.664\text{ m} = 339.968\text{ m/s} \approx 340\text{ m/s}.

Final answer

ΔL=1.40 cm\Delta L = 1.40\text{ cm} (or 0.0140 m0.0140\text{ m}); v=340 m/sv = 340\text{ m/s}

NEXT STEPS
Final Takeaways from Your Teacher
  • Always write explicit unit labels inside your scratch multiplication to verify dimensional consistency.

  • Perform a quick order-of-magnitude sanity check whenever calculating fundamental physical constants such as the speed of sound.

Lock it in

Similar question

01

A tuning fork produces consecutive resonances in a resonance tube at air-column lengths L1=24.0 cmL_1 = 24.0\text{ cm} and L2=74.0 cmL_2 = 74.0\text{ cm}. Calculate the end correction ΔL\Delta L and the wavelength λ\lambda.

Answer

λ=2(L2−L1)=2(74.0−24.0)=100.0 cm\lambda = 2(L_2 - L_1) = 2(74.0 - 24.0) = 100.0\text{ cm}. Then ΔL=λ4−L1=25.0 cm−24.0 cm=1.0 cm\Delta L = \frac{\lambda}{4} - L_1 = 25.0\text{ cm} - 24.0\text{ cm} = 1.0\text{ cm}.

02

A tube closed at one end resonates with a 440 Hz440\text{ Hz} sound source at L1=18.0 cmL_1 = 18.0\text{ cm} and L2=57.0 cmL_2 = 57.0\text{ cm}. Determine the speed of sound vv and the end correction ΔL\Delta L.

Answer

λ2=57.0−18.0=39.0 cm  ⟹  λ=78.0 cm=0.780 m\frac{\lambda}{2} = 57.0 - 18.0 = 39.0\text{ cm} \implies \lambda = 78.0\text{ cm} = 0.780\text{ m}. Wave speed: v=fλ=440×0.780=343.2 m/sv = f\lambda = 440 \times 0.780 = 343.2\text{ m/s}. End correction: ΔL=λ4−L1=19.5−18.0=1.5 cm\Delta L = \frac{\lambda}{4} - L_1 = 19.5 - 18.0 = 1.5\text{ cm}.

03

An open cylindrical pipe of inner radius r=2.5 cmr = 2.5\text{ cm} has an end correction given by ΔL≈0.6r\Delta L \approx 0.6r at each open end. If the pipe resonates in its fundamental mode at f=330 Hzf = 330\text{ Hz} with v=343.2 m/sv = 343.2\text{ m/s}, calculate the physical length LL of the pipe.

Answer

For a pipe open at both ends, the effective length is Leff=L+2ΔL=λ2L_{\text{eff}} = L + 2\Delta L = \frac{\lambda}{2}. Wavelength: λ=vf=343.2330=1.04 m=104.0 cm\lambda = \frac{v}{f} = \frac{343.2}{330} = 1.04\text{ m} = 104.0\text{ cm}. Thus Leff=52.0 cmL_{\text{eff}} = 52.0\text{ cm}. Total end correction: 2ΔL=2(0.6×2.5 cm)=3.0 cm2\Delta L = 2(0.6 \times 2.5\text{ cm}) = 3.0\text{ cm}. Physical length: L=52.0 cm−3.0 cm=49.0 cmL = 52.0\text{ cm} - 3.0\text{ cm} = 49.0\text{ cm}.

Loading workspace…