Resources

In an analytical physics laboratory experiment, a student determines the electrical conductivity σ\sigma of an unknown cylindrical electrolyte column. The column has an internal diameter D=1.20 cmD = 1.20\text{ cm} and an electrode separation length L=25.0 cmL = 25.0\text{ cm}. A digital multimeter measures a resistance of R=850 ΩR = 850\text{ }\Omega. Resistance is related to conductivity by R=LσAR = \frac{L}{\sigma A}, where AA is the cross-sectional area. (a) Derive the expression for the SI derived unit of electrical conductivity, the siemens per meter (S/m\text{S}/\text{m}), expressed strictly in SI base units. (b) Compute the conductivity σ\sigma of the electrolyte solution in S/m\text{S}/\text{m} using the student's experimental data.

Answer and steps

Final answer

(a) 1 S/m=kg−1⋅m−3⋅s3⋅A21\text{ S}/\text{m} = \text{kg}^{-1}\cdot\text{m}^{-3}\cdot\text{s}^3\cdot\text{A}^2 (or s3⋅A2kg⋅m3\frac{\text{s}^3\cdot\text{A}^2}{\text{kg}\cdot\text{m}^3}); (b) σ=2.60 S/m\sigma = 2.60\text{ S}/\text{m}

Steps

Part (a): Expressing Siemens per Meter in SI Base Units

  1. Relate electrical quantities to fundamental mechanical and electrical units:

    • Current (II): The base unit is the ampere (A\text{A}).
    • Electric charge (qq): q=I⋅t  ⟹  [q]=A⋅sq = I \cdot t \implies [q] = \text{A}\cdot\text{s}.
    • Potential difference (VV): Potential difference is the work done per unit charge, V=WqV = \frac{W}{q}. Work (W)=Force⋅distance=(m⋅a)⋅d  ⟹  [W]=kg⋅m2⋅s−2\text{Work } (W) = \text{Force} \cdot \text{distance} = (m\cdot a)\cdot d \implies [W] = \text{kg}\cdot\text{m}^2\cdot\text{s}^{-2} Substituting this into the definition of potential: [V]=kg⋅m2⋅s−2A⋅s=kg⋅m2⋅s−3⋅A−1[V] = \frac{\text{kg}\cdot\text{m}^2\cdot\text{s}^{-2}}{\text{A}\cdot\text{s}} = \text{kg}\cdot\text{m}^2\cdot\text{s}^{-3}\cdot\text{A}^{-1}
  2. Find the base units of resistance (RR): Using Ohm's law, R=VIR = \frac{V}{I}: [R]=kg⋅m2⋅s−3⋅A−1A=kg⋅m2⋅s−3⋅A−2=1 Ω[R] = \frac{\text{kg}\cdot\text{m}^2\cdot\text{s}^{-3}\cdot\text{A}^{-1}}{\text{A}} = \text{kg}\cdot\text{m}^2\cdot\text{s}^{-3}\cdot\text{A}^{-2} = 1\text{ }\Omega
  3. Find the base units of conductance (GG) and conductivity (σ\sigma):

    • Conductance GG in siemens (S\text{S}) is the reciprocal of resistance: [S]=[Ω]−1=kg−1⋅m−2⋅s3⋅A2[\text{S}] = [\Omega]^{-1} = \text{kg}^{-1}\cdot\text{m}^{-2}\cdot\text{s}^3\cdot\text{A}^2
    • Conductivity has units of siemens per meter (S/m\text{S}/\text{m}): [σ]=[S]m=kg−1⋅m−2⋅s3⋅A2m=kg−1⋅m−3⋅s3⋅A2(or s3⋅A2kg⋅m3)[\sigma] = \frac{[\text{S}]}{\text{m}} = \frac{\text{kg}^{-1}\cdot\text{m}^{-2}\cdot\text{s}^3\cdot\text{A}^2}{\text{m}} = \text{kg}^{-1}\cdot\text{m}^{-3}\cdot\text{s}^3\cdot\text{A}^2 \quad \left(\text{or } \frac{\text{s}^3\cdot\text{A}^2}{\text{kg}\cdot\text{m}^3}\right)

Part (b): Calculating Conductivity σ\sigma

  1. Convert given values to SI units:

    • Length: L=25.0 cm=0.250 mL = 25.0\text{ cm} = 0.250\text{ m}
    • Diameter: D=1.20 cm=0.0120 mD = 1.20\text{ cm} = 0.0120\text{ m}
    • Resistance: R=850 ΩR = 850\text{ }\Omega
  2. Calculate the cross-sectional area AA: A=πD24=π(0.0120 m)24≈1.1310×10−4 m2A = \frac{\pi D^2}{4} = \frac{\pi (0.0120\text{ m})^2}{4} \approx 1.1310 \times 10^{-4}\text{ m}^2

    Pitfall: A common error is squaring the diameter without dividing by 44 (or forgetting to convert centimeters to meters before squaring).

  3. Rearrange the resistance formula and solve for σ\sigma: R=LσA  ⟹  σ=LR⋅AR = \frac{L}{\sigma A} \implies \sigma = \frac{L}{R \cdot A} Substitute the numerical values: σ=0.250 m850 Ω⋅1.1310×10−4 m2≈0.2500.096135≈2.60 S/m\sigma = \frac{0.250\text{ m}}{850\text{ }\Omega \cdot 1.1310 \times 10^{-4}\text{ m}^2} \approx \frac{0.250}{0.096135} \approx 2.60\text{ S/m}

To three significant figures, the conductivity is σ=2.60 S/m\sigma = 2.60\text{ S/m}.

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student uses diameter instead of radius when calculating the cross-sectional area, resulting in an area that is four times too large and an underestimated conductivity.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    σ=LRA  ⟹  [σ]=mΩ⋅m2=1Ω⋅m\sigma = \frac{L}{RA} \implies [\sigma] = \frac{\text{m}}{\Omega\cdot\text{m}^2} = \frac{1}{\Omega\cdot\text{m}} Ω=VA=kg⋅m2⋅s−3⋅A−2  ⟹  [σ]=s3⋅A2⋅kg−1⋅m−3\Omega = \frac{\text{V}}{\text{A}} = \text{kg}\cdot\text{m}^2\cdot\text{s}^{-3}\cdot\text{A}^{-2} \implies [\sigma] = \text{s}^3\cdot\text{A}^2\cdot\text{kg}^{-1}\cdot\text{m}^{-3}

  2. Step 2

    D=1.20 cm=0.0120 m  ⟹  A=πD2=π(0.0120 m)2=4.524×10−4 m2D = 1.20\text{ cm} = 0.0120\text{ m} \implies A = \pi D^2 = \pi (0.0120\text{ m})^2 = 4.524 \times 10^{-4}\text{ m}^2

    Correct

    A=πD24=π(0.0120 m)24≈1.131×10−4 m2A = \frac{\pi D^2}{4} = \frac{\pi (0.0120\text{ m})^2}{4} \approx 1.131 \times 10^{-4}\text{ m}^2

    You used A=πD2A = \pi D^2 instead of A=πr2=πD24A = \pi r^2 = \frac{\pi D^2}{4}. When given diameter DD, you must either divide DD by 22 first to get radius r=0.0060 mr = 0.0060\text{ m} or divide D2D^2 by 44.

  3. Step 3

    L=25.0 cm=0.250 m  ⟹  σ=0.250850×4.524×10−4=0.650 S/mL = 25.0\text{ cm} = 0.250\text{ m} \implies \sigma = \frac{0.250}{850 \times 4.524 \times 10^{-4}} = 0.650\text{ S/m}

    Correct

    σ=0.250 m850 Ω×1.131×10−4 m2≈2.60 S/m\sigma = \frac{0.250\text{ m}}{850\text{ }\Omega \times 1.131 \times 10^{-4}\text{ m}^2} \approx 2.60\text{ S/m}

    Your calculation correctly followed your rearranged formula σ=LRA\sigma = \frac{L}{RA}, but the numerical value was divided by an area that was four times too large.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly rearranged the resistance formula for conductivity as σ=LRA\sigma = \frac{L}{RA}.

You accurately tracked and derived the base SI units for potential, resistance, and conductivity.

You correctly converted centimeters to meters for both length and diameter.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Circle Area Diameter vs Radius Confusion

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You substituted diameter DD directly into the area formula πr2\pi r^2 as πD2\pi D^2, omitting the factor of 14\frac{1}{4} (or failing to divide the diameter by 22 to obtain radius).

REASONING PATH
Your ACEpath teacher’s suggested approach
Area from Diameter
  • A circle's area is A=πr2=πD24A = \pi r^2 = \frac{\pi D^2}{4}.

  • Whenever a problem provides a diameter DD, immediately write r=D2r = \frac{D}{2} before calculating area, or explicitly write A=πD24A = \frac{\pi D^2}{4}.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Recalculate cross-sectional area with the correct formula: A=π(0.0120 m)24≈1.1310×10−4 m2A = \frac{\pi (0.0120\text{ m})^2}{4} \approx 1.1310 \times 10^{-4}\text{ m}^2.

  2. Substitute into σ=LRA\sigma = \frac{L}{RA}: σ=0.250 m850 Ω×1.1310×10−4 m2\sigma = \frac{0.250\text{ m}}{850\text{ }\Omega \times 1.1310 \times 10^{-4}\text{ m}^2}.

  3. Compute the final numerical quotient: σ≈2.60 S/m\sigma \approx 2.60\text{ S/m}.

Final answer

(a) [σ]=kg−1⋅m−3⋅s3⋅A2[\sigma] = \text{kg}^{-1}\cdot\text{m}^{-3}\cdot\text{s}^3\cdot\text{A}^2; (b) σ=2.60 S/m\sigma = 2.60\text{ S/m}

NEXT STEPS
Final Takeaways from Your Teacher
  • Always write down whether a given dimension is radius or diameter before choosing your area formula.

  • Check if your computed area matches an order-of-magnitude estimate: for D≈1 cmD \approx 1\text{ cm}, r≈0.5 cmr \approx 0.5\text{ cm}, so A≈3×0.25 cm2≈0.75 cm2=0.75×10−4 m2A \approx 3 \times 0.25\text{ cm}^2 \approx 0.75\text{ cm}^2 = 0.75 \times 10^{-4}\text{ m}^2.

OverviewACEpath Teacher's Diagnosis

02 The student forgets to convert centimeters to meters, resulting in area and length values that are off by powers of ten.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    σ=LRA  ⟹  [σ]=mΩ⋅m2=Ω−1⋅m−1  ⟹  1 Ω=VA=1 J/CA=kg⋅m2⋅s−2A2⋅s=kg⋅m2⋅s−3⋅A−2  ⟹  [σ]=s3⋅A2⋅kg−1⋅m−3\sigma = \frac{L}{RA} \implies [\sigma] = \frac{\text{m}}{\Omega\cdot\text{m}^2} = \Omega^{-1}\cdot\text{m}^{-1} \implies 1\text{ }\Omega = \frac{\text{V}}{\text{A}} = \frac{1\text{ J/C}}{\text{A}} = \frac{\text{kg}\cdot\text{m}^2\cdot\text{s}^{-2}}{\text{A}^2\cdot\text{s}} = \text{kg}\cdot\text{m}^2\cdot\text{s}^{-3}\cdot\text{A}^{-2} \implies [\sigma] = \text{s}^3\cdot\text{A}^2\cdot\text{kg}^{-1}\cdot\text{m}^{-3}

  2. Step 2

    r=D2=0.600 cm  ⟹  A=πr2=π(0.600)2=1.131 cm2  ⟹  σ=LRA=25.0850×1.131r = \frac{D}{2} = 0.600\text{ cm} \implies A = \pi r^2 = \pi (0.600)^2 = 1.131\text{ cm}^2 \implies \sigma = \frac{L}{RA} = \frac{25.0}{850 \times 1.131}

    Correct

    r=0.00600 m  ⟹  A=π(0.00600 m)2=1.131×10−4 m2  ⟹  σ=0.250 m850 Ω×1.131×10−4 m2r = 0.00600\text{ m} \implies A = \pi (0.00600\text{ m})^2 = 1.131 \times 10^{-4}\text{ m}^2 \implies \sigma = \frac{0.250\text{ m}}{850\text{ }\Omega \times 1.131 \times 10^{-4}\text{ m}^2}

    You substituted L=25.0 cmL = 25.0\text{ cm} and A=1.131 cm2A = 1.131\text{ cm}^2 without converting them into standard SI units (meters and square meters). Evaluating cmΩ⋅cm2\frac{\text{cm}}{\Omega\cdot\text{cm}^2} yields conductivity in S/cm\text{S/cm}, not the requested S/m\text{S/m}.

  3. Step 3

    σ=0.0260 S/m\sigma = 0.0260\text{ S/m}

    Correct

    σ=2.60 S/m\sigma = 2.60\text{ S/m}

    Your arithmetic on the substituted numbers was carried out properly, but because the input dimensions were in centimeters, your result represents 0.0260 S/cm0.0260\text{ S/cm}, which equals 2.60 S/m2.60\text{ S/m}.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly related electrical resistance to potential difference, current, work, and charge to derive the SI base units.

You correctly identified and applied the formula relating conductivity, length, cross-sectional area, and resistance.

You correctly computed the cylinder radius from the diameter and calculated the cross-sectional area with proper geometry.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Missing Unit Conversion to SI Base Units

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You substituted dimensioned geometric measurements in centimeters and square centimeters directly into an equation expecting SI base units (meters), leading to an unscaled conductivity in S/cm\text{S/cm} labeled as S/m\text{S/m}.

REASONING PATH
Your ACEpath teacher’s suggested approach
Convert Inputs to Standard SI Units First
  • Derived physical formulas with SI outputs require base SI inputs: length must be in m\text{m} and area in m2\text{m}^2.

  • Always convert all geometric quantities to meters before computing area and substituting into physical formulas.

Area Unit Scaling Factor
  • 1 cm2=(10−2 m)2=10−4 m21\text{ cm}^2 = (10^{-2}\text{ m})^2 = 10^{-4}\text{ m}^2, not 10−2 m210^{-2}\text{ m}^2.

  • When converting areas or volumes, square or cube the linear conversion factor explicitly.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Convert diameter and length to meters: D=0.0120 mD = 0.0120\text{ m} (so r=0.00600 mr = 0.00600\text{ m}) and L=0.250 mL = 0.250\text{ m}.

  2. Compute cross-sectional area in SI units: A=πr2=π(0.00600 m)2≈1.1310×10−4 m2A = \pi r^2 = \pi (0.00600\text{ m})^2 \approx 1.1310 \times 10^{-4}\text{ m}^2.

  3. Substitute into σ=LRA\sigma = \frac{L}{RA}: σ=0.250 m850 Ω×1.1310×10−4 m2≈2.60 S/m\sigma = \frac{0.250\text{ m}}{850\text{ }\Omega \times 1.1310 \times 10^{-4}\text{ m}^2} \approx 2.60\text{ S/m}.

Final answer

(a) [σ]=kg−1⋅m−3⋅s3⋅A2[\sigma] = \text{kg}^{-1}\cdot\text{m}^{-3}\cdot\text{s}^3\cdot\text{A}^2; (b) σ=2.60 S/m\sigma = 2.60\text{ S/m}

NEXT STEPS
Final Takeaways from Your Teacher
  • Write explicit unit labels next to every number as you substitute it into an equation to catch mixed-unit mismatches before evaluating.

  • Practice converting derived area units: remember that converting cm2\text{cm}^2 to m2\text{m}^2 requires multiplying by 10−410^{-4}.

  • Check your final units by dimensional consistency: ensure that cmΩ⋅cm2=S/cm\frac{\text{cm}}{\Omega\cdot\text{cm}^2} = \text{S/cm}, and multiply by 100 cm/m100\text{ cm/m} to reach S/m\text{S/m}.

OverviewACEpath Teacher's Diagnosis

03 The student misinverts the definition formula and solves for conductivity as σ = R A / L instead of σ = L / (R A).

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    R=LσA  ⟹  σ=LRA  ⟹  Ω=kg⋅m2⋅s−3⋅A−2  ⟹  [σ]=1Ω⋅m=s3⋅A2⋅kg−1⋅m−3R = \frac{L}{\sigma A} \implies \sigma = \frac{L}{RA} \implies \Omega = \text{kg}\cdot\text{m}^2\cdot\text{s}^{-3}\cdot\text{A}^{-2} \implies [\sigma] = \frac{1}{\Omega\cdot\text{m}} = \text{s}^3\cdot\text{A}^2\cdot\text{kg}^{-1}\cdot\text{m}^{-3}

  2. Step 2

    r=1.20 cm2=0.00600 m  ⟹  A=π(0.00600 m)2=1.131×10−4 m2  ⟹  L=0.250 mr = \frac{1.20\text{ cm}}{2} = 0.00600\text{ m} \implies A = \pi (0.00600\text{ m})^2 = 1.131\times 10^{-4}\text{ m}^2 \implies L = 0.250\text{ m}

  3. Step 3

    σ=RAL=850×1.131×10−40.250\sigma = \frac{RA}{L} = \frac{850 \times 1.131\times 10^{-4}}{0.250}

    Correct

    σ=LRA=0.250 m850 Ω×1.131×10−4 m2\sigma = \frac{L}{RA} = \frac{0.250\text{ m}}{850\text{ }\Omega \times 1.131\times 10^{-4}\text{ m}^2}

    You wrote σ=RAL\sigma = \frac{RA}{L} instead of σ=LRA\sigma = \frac{L}{RA}. Although you rearranged R=LσAR = \frac{L}{\sigma A} correctly in part (a), you accidentally inverted the formula in part (b) (which corresponds to resistivity ρ=RAL\rho = \frac{RA}{L}, rather than conductivity σ\sigma).

  4. Step 4

    σ=0.385 S/m\sigma = 0.385\text{ S/m}

    Correct

    σ≈2.60 S/m\sigma \approx 2.60\text{ S/m}

    Your numerical computation followed directly from your inverted formula in Step 3, yielding 12.60≈0.385 S/m\frac{1}{2.60} \approx 0.385\text{ S/m}.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly derived the SI base units of conductivity as kg−1⋅m−3⋅s3⋅A2\text{kg}^{-1}\cdot\text{m}^{-3}\cdot\text{s}^3\cdot\text{A}^2.

You converted all given values into standard SI units before calculating.

You correctly calculated the cross-sectional area from the column's diameter.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Formula inversion / reciprocal confusion

You correctly isolated σ=LRA\sigma = \frac{L}{RA} in part (a), but inadvertently switched it to σ=RAL\sigma = \frac{RA}{L} when plugging in numbers for part (b).

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing conductivity σ\sigma with resistivity ρ=RAL\rho = \frac{RA}{L}, or making an algebraic transposition error when setting up the substitution step.

REASONING PATH
Your ACEpath teacher’s suggested approach
Conductivity vs. Resistivity
  • Conductivity is the reciprocal of resistivity: σ=1ρ\sigma = \frac{1}{\rho}. Since R=ρLA=LσAR = \rho \frac{L}{A} = \frac{L}{\sigma A}, solving for σ\sigma gives σ=LRA\sigma = \frac{L}{RA}.

  • Check that the length LL stays in the numerator and resistance RR stays in the denominator whenever you solve for conductivity σ\sigma.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Substitute the values into the correct formula: σ=LRA\sigma = \frac{L}{RA}

  2. σ=0.250 m850 Ω×1.131×10−4 m2=0.2500.096135\sigma = \frac{0.250\text{ m}}{850\text{ }\Omega \times 1.131\times 10^{-4}\text{ m}^2} = \frac{0.250}{0.096135}

  3. σ≈2.60 S/m\sigma \approx 2.60\text{ S/m}

Final answer

σ=2.60 S/m\sigma = 2.60\text{ S/m}

NEXT STEPS
Final Takeaways from Your Teacher
  • Be careful to carry your exact algebraic derivation from part (a) directly into part (b).

  • Perform a quick units and sanity check: higher resistance RR must decrease conductivity σ\sigma, so RR must be in the denominator.

Lock it in

Similar question

01

A cylindrical copper wire has diameter D=0.400 mmD = 0.400\text{ mm} and length L=2.00 mL = 2.00\text{ m}. The measured resistance is R=0.272 ΩR = 0.272\text{ }\Omega. Calculate the electrical conductivity σ\sigma of the copper in S/m\text{S}/\text{m}.

Answer

r=D2=0.200 mm=2.00×10−4 mr = \frac{D}{2} = 0.200\text{ mm} = 2.00 \times 10^{-4}\text{ m}. Cross-sectional area A=πr2=π(2.00×10−4 m)2≈1.2566×10−7 m2A = \pi r^2 = \pi (2.00 \times 10^{-4}\text{ m})^2 \approx 1.2566 \times 10^{-7}\text{ m}^2. Conductivity σ=LRA=2.00 m0.272 Ω×1.2566×10−7 m2≈5.85×107 S/m\sigma = \frac{L}{RA} = \frac{2.00\text{ m}}{0.272\text{ }\Omega \times 1.2566 \times 10^{-7}\text{ m}^2} \approx 5.85 \times 10^7\text{ S/m}.

02

An electrolyte tube of length L=15.0 cmL = 15.0\text{ cm} has an inner circular cross-section with diameter D=8.00 mmD = 8.00\text{ mm}. If the solution has conductivity σ=1.50 S/m\sigma = 1.50\text{ S/m}, what resistance RR will be measured across the ends?

Answer

Convert to SI units: L=0.150 mL = 0.150\text{ m}, D=0.00800 m  ⟹  r=0.00400 mD = 0.00800\text{ m} \implies r = 0.00400\text{ m}. Cross-sectional area A=π(0.00400 m)2≈5.027×10−5 m2A = \pi (0.00400\text{ m})^2 \approx 5.027 \times 10^{-5}\text{ m}^2. Resistance R=LσA=0.150 m(1.50 S/m)(5.027×10−5 m2)≈1.99×103 ΩR = \frac{L}{\sigma A} = \frac{0.150\text{ m}}{(1.50\text{ S/m})(5.027 \times 10^{-5}\text{ m}^2)} \approx 1.99 \times 10^3\text{ }\Omega (1.99 kΩ1.99\text{ k}\Omega).

03

Derive the SI base unit expression for electrical resistivity ρ\rho and verify its dimensional consistency with the resistance relation R=ρLAR = \frac{\rho L}{A}.

Answer

Resistivity is the reciprocal of conductivity: [ρ]=[σ]−1=1kg−1⋅m−3⋅s3⋅A2=kg⋅m3⋅s−3⋅A−2[\rho] = [\sigma]^{-1} = \frac{1}{\text{kg}^{-1}\cdot\text{m}^{-3}\cdot\text{s}^3\cdot\text{A}^2} = \text{kg}\cdot\text{m}^3\cdot\text{s}^{-3}\cdot\text{A}^{-2} (or Ω⋅m\Omega\cdot\text{m}). Checking with R=ρLAR = \frac{\rho L}{A}: [R]=(Ω⋅m)⋅mm2=Ω[R] = \frac{(\Omega\cdot\text{m})\cdot\text{m}}{\text{m}^2} = \Omega, which equals kg⋅m2⋅s−3⋅A−2\text{kg}\cdot\text{m}^2\cdot\text{s}^{-3}\cdot\text{A}^{-2}.

Loading workspace…