Resources

A metal toolbox of mass m=12.0 kgm = 12.0\text{ kg} sits on a level concrete surface with coefficients of friction μs=0.520\mu_s = 0.520 and μk=0.380\mu_k = 0.380. A technician pulls on an attached rope with a tension of T=65.0 NT = 65.0\text{ N} directed at an angle θ\theta above the horizontal. If the magnitude of the applied horizontal pulling component exactly equals the maximum static friction threshold, causing impending motion, determine the required pulling angle θ\theta. Take g=9.80 m/s2g = 9.80\text{ m/s}^2.

Answer and steps

Final answer

θ=23.6∘\theta = 23.6^\circ (or 0.412 rad0.412\text{ rad})

Steps

01

Identify the relevant forces and the role of friction

Before the toolbox begins to move, it is in static equilibrium up to the verge of slipping (impending motion).

  • Static vs. kinetic friction: Because the toolbox has not yet started sliding, the threshold of motion is governed exclusively by the coefficient of static friction, μs=0.520\mu_s = 0.520. The kinetic coefficient μk=0.380\mu_k = 0.380 only applies once continuous sliding is underway and is not used here.
  • Forces acting on the toolbox:
    1. Gravity acting vertically downward: W=mgW = mg
    2. Normal force exerted upward by the floor: NN
    3. Tension force pulling at an angle θ\theta above the horizontal: TT
    4. Static friction opposing the impending forward motion: fsf_s

02

Resolve forces along the vertical and horizontal axes

Resolve the tension TT into its rectangular components:

  • Horizontal pulling component: Tx=Tcos⁡θT_x = T \cos\theta
  • Vertical lifting component: Ty=Tsin⁡θT_y = T \sin\theta

Vertical Equilibrium (∑Fy=0\sum F_y = 0):

Since there is no vertical acceleration, the upward forces balance the downward forces: N+Tsin⁡θ−mg=0N + T \sin\theta - mg = 0 N=mg−Tsin⁡θN = mg - T \sin\theta

Key Pitfall: A common error is assuming N=mgN = mg. Because the rope pulls upward at an angle θ\theta, it partially relieves the contact pressure between the toolbox and the floor, reducing the normal force to N=mg−Tsin⁡θN = mg - T \sin\theta.


03

Apply the condition for impending motion

At the threshold of motion, the horizontal pulling force balances the maximum possible static friction force fs,maxf_{s,\text{max}}: Tx=fs,max=μsNT_x = f_{s,\text{max}} = \mu_s N

Substitute the expression for the normal force NN: Tcos⁡θ=μs(mg−Tsin⁡θ)T \cos\theta = \mu_s (mg - T \sin\theta)

Expand and group terms containing the unknown angle θ\theta on one side: Tcos⁡θ+μsTsin⁡θ=μsmgT \cos\theta + \mu_s T \sin\theta = \mu_s mg T(cos⁡θ+μssin⁡θ)=μsmgT(\cos\theta + \mu_s \sin\theta) = \mu_s mg


04

Substitute the given values and solve for θ\theta

Substitute the given numerical values:

  • m=12.0 kgm = 12.0\text{ kg}
  • g=9.80 m/s2  ⟹  mg=(12.0)(9.80)=117.6 Ng = 9.80\text{ m/s}^2 \implies mg = (12.0)(9.80) = 117.6\text{ N}
  • μs=0.520\mu_s = 0.520
  • T=65.0 NT = 65.0\text{ N}

This yields the trigonometric relation: cos⁡θ+μssin⁡θ=μsmgT\cos\theta + \mu_s \sin\theta = \frac{\mu_s mg}{T}

Solving this relation for the required angle θ\theta produces: θ≈23.6∘(or 0.412 rad)\theta \approx 23.6^\circ \quad (\text{or } 0.412\text{ rad})

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student forgets that the vertical component of tension reduces the normal force and incorrectly sets N = m g.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    N=mg=12.0×9.80=117.6 NN = mg = 12.0 \times 9.80 = 117.6\text{ N}

    Correct

    N=mg−Tsin⁡θN = mg - T\sin\theta

    Because the rope pulls at an angle θ\theta above the horizontal, the upward vertical component Tsin⁡θT\sin\theta partially supports the toolbox, reducing the normal force to N=mg−Tsin⁡θN = mg - T\sin\theta.

  2. Step 2

    fs,max⁡=μsN=0.520×117.6=61.15 Nf_{s,\max} = \mu_s N = 0.520 \times 117.6 = 61.15\text{ N}

    Correct

    fs,max⁡=μs(mg−Tsin⁡θ)f_{s,\max} = \mu_s (mg - T\sin\theta)

    You correctly used the static friction formula fs,max⁡=μsNf_{s,\max} = \mu_s N, but this step inherits the incorrect normal force from Step 1.

  3. Step 3

    Tcos⁡θ=fs,max⁡  ⟹  65.0cos⁡θ=61.15  ⟹  cos⁡θ=61.1565.0≈0.9408T\cos\theta = f_{s,\max} \implies 65.0\cos\theta = 61.15 \implies \cos\theta = \frac{61.15}{65.0} \approx 0.9408

    Correct

    Tcos⁡θ+μsTsin⁡θ=μsmgT\cos\theta + \mu_s T\sin\theta = \mu_s mg

    You correctly balanced the horizontal pulling component with the maximum static friction force, but the resulting algebraic equation carries forward the constant normal force assumption.

  4. Step 4

    θ=arccos⁡(0.9408)≈19.8∘\theta = \arccos(0.9408) \approx 19.8^\circ

    Correct

    θ≈23.6∘\theta \approx 23.6^\circ

    Your angle calculation follows directly from your previous numerical value, but it is incorrect because the vertical relief of the normal force was omitted.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly selected the coefficient of static friction μs\mu_s instead of the kinetic coefficient to model impending motion.

You correctly identified that the horizontal component of the tension is Tcos⁡θT\cos\theta and set it equal to the threshold friction force.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Omission of vertical force component in normal force

You equated normal force directly to mgmg out of habit, overlooking that angled forces alter contact pressure with the floor.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Treating N=mgN = mg as a universal identity rather than deriving NN from Newton's second law along the vertical axis (∑Fy=0\sum F_y = 0).

REASONING PATH
Your ACEpath teacher’s suggested approach
Vertical Equilibrium Check
  • Whenever an external force acts at an angle, the normal force on a horizontal surface is N=mg±FyN = mg \pm F_y, never automatically mgmg.

  • Always draw a free-body diagram and explicitly write ∑Fy=0\sum F_y = 0 before writing an expression for friction.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Apply vertical equilibrium: ∑Fy=N+Tsin⁡θ−mg=0  ⟹  N=mg−Tsin⁡θ\sum F_y = N + T\sin\theta - mg = 0 \implies N = mg - T\sin\theta.

  2. Substitute NN into the impending motion equation: Tcos⁡θ=μs(mg−Tsin⁡θ)T\cos\theta = \mu_s (mg - T\sin\theta).

  3. Rearrange terms involving θ\theta: T(cos⁡θ+μssin⁡θ)=μsmgT(\cos\theta + \mu_s \sin\theta) = \mu_s mg.

  4. Substitute the given numbers: 65.0(cos⁡θ+0.520sin⁡θ)=0.520×12.0×9.80=61.15265.0(\cos\theta + 0.520\sin\theta) = 0.520 \times 12.0 \times 9.80 = 61.152, giving cos⁡θ+0.520sin⁡θ=0.9408\cos\theta + 0.520\sin\theta = 0.9408.

  5. Solve the trigonometric equation to find θ≈23.6∘\theta \approx 23.6^\circ.

Final answer

θ≈23.6∘\theta \approx 23.6^\circ (or 0.412 rad0.412\text{ rad})

NEXT STEPS
Final Takeaways from Your Teacher
  • Before setting up friction equations, always write out ∑Fy=0\sum F_y = 0 to express the normal force in terms of all vertical components.

  • Practice solving transcendental linear combinations of sine and cosine of the form Acos⁡θ+Bsin⁡θ=CA\cos\theta + B\sin\theta = C using the auxiliary angle method.

OverviewACEpath Teacher's Diagnosis

02 The student uses the coefficient of kinetic friction μk instead of the coefficient of static friction μs for impending motion.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    N=mg−Tsin⁡θ=117.6−65.0sin⁡θN = mg - T\sin\theta = 117.6 - 65.0\sin\theta

  2. Step 2

    Tcos⁡θ=μkN  ⟹  65.0cos⁡θ=0.380×(117.6−65.0sin⁡θ)T\cos\theta = \mu_k N \implies 65.0\cos\theta = 0.380 \times (117.6 - 65.0\sin\theta)

    Correct

    Tcos⁡θ=μsN  ⟹  65.0cos⁡θ=0.520×(117.6−65.0sin⁡θ)T\cos\theta = \mu_s N \implies 65.0\cos\theta = 0.520 \times (117.6 - 65.0\sin\theta)

    The condition of impending motion means the object is on the verge of slipping but still static. Therefore, the maximum opposing friction is static friction, fs,max=μsNf_{s,\text{max}} = \mu_s N, so you need to use μs=0.520\mu_s = 0.520 instead of μk=0.380\mu_k = 0.380.

  3. Step 3

    65.0cos⁡θ+24.7sin⁡θ=44.688  ⟹  R=65.02+24.72≈69.53,ϕ=arctan⁡(0.380)≈20.81∘  ⟹  cos⁡(θ−ϕ)≈0.6427  ⟹  θ−ϕ≈50.01∘65.0\cos\theta + 24.7\sin\theta = 44.688 \implies R = \sqrt{65.0^2 + 24.7^2} \approx 69.53, \phi = \arctan(0.380) \approx 20.81^\circ \implies \cos(\theta - \phi) \approx 0.6427 \implies \theta - \phi \approx 50.01^\circ

    Correct

    65.0cos⁡θ+33.8sin⁡θ=61.152  ⟹  cos⁡θ+0.520sin⁡θ=0.940865.0\cos\theta + 33.8\sin\theta = 61.152 \implies \cos\theta + 0.520\sin\theta = 0.9408

    Your mathematical technique for solving Acos⁡θ+Bsin⁡θ=CA\cos\theta + B\sin\theta = C using an auxiliary angle was well executed, but the numerical coefficients were affected by using μk\mu_k.

  4. Step 4

    θ=20.81∘+50.01∘≈70.8∘\theta = 20.81^\circ + 50.01^\circ \approx 70.8^\circ

    Correct

    θ≈23.6∘\theta \approx 23.6^\circ

    Because μk\mu_k was substituted in the equilibrium equation, the calculated angle does not match the threshold angle required for impending motion.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly accounted for the upward component of tension reducing the normal force to N=mg−Tsin⁡θN = mg - T\sin\theta.

You skillfully applied the auxiliary angle method to solve a linear combination of sine and cosine.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Kinetic vs. Static Friction Confusion

You substituted the coefficient of kinetic friction μk\mu_k instead of the static friction coefficient μs\mu_s into the impending motion equilibrium.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Impending motion describes the boundary state of static equilibrium immediately before relative motion begins. At this threshold, contact surfaces remain stationary relative to each other, so the threshold force is determined strictly by the maximum static friction force fs,max=μsNf_{s,\text{max}} = \mu_s N. The kinetic coefficient μk\mu_k only applies after relative sliding has actually begun.

REASONING PATH
Your ACEpath teacher’s suggested approach
State of Relative Motion
  • Use μs\mu_s whenever an object is stationary, held in place, or at impending motion (the threshold of slipping). Use μk\mu_k only when the surfaces are actively sliding past one another.

  • Check the problem wording: 'impending motion', 'verge of slipping', or 'minimum force to start motion' all require μs\mu_s.

Friction Magnitude Condition
  • At impending motion, fs=fs,max=μsNf_s = f_{s,\text{max}} = \mu_s N.

  • Equate the driving force component directly to μsN\mu_s N, never μkN\mu_k N.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Set up the horizontal equilibrium at impending slip: Tcos⁡θ=μsN=μs(mg−Tsin⁡θ)T\cos\theta = \mu_s N = \mu_s(mg - T\sin\theta).

  2. Substitute the given parameters: 65.0cos⁡θ=0.520(117.6−65.0sin⁡θ)=61.152−33.8sin⁡θ65.0\cos\theta = 0.520(117.6 - 65.0\sin\theta) = 61.152 - 33.8\sin\theta.

  3. Rearrange into standard form: 65.0cos⁡θ+33.8sin⁡θ=61.15265.0\cos\theta + 33.8\sin\theta = 61.152, or cos⁡θ+0.520sin⁡θ=0.9408\cos\theta + 0.520\sin\theta = 0.9408.

  4. Solve for the required angle θ\theta to obtain θ≈23.6∘\theta \approx 23.6^\circ (or 0.412 rad0.412\text{ rad}).

Final answer

θ≈23.6∘\theta \approx 23.6^\circ

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the distinction between impending motion (fs=μsNf_s = \mu_s N) and steady sliding (fk=μkNf_k = \mu_k N).

  • Practice identifying trigger words in problem statements that indicate static threshold conditions.

  • Re-solve similar problems where pulling angles alter both the driving force and the normal force.

OverviewACEpath Teacher's Diagnosis

03 The student swaps the trigonometric functions for the horizontal and vertical force components.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    N=mg−65.0cos⁡θ=117.6−65.0cos⁡θ  ⟹  Tsin⁡θ=μsN=0.520×(117.6−65.0cos⁡θ)N = mg - 65.0\cos\theta = 117.6 - 65.0\cos\theta \implies T\sin\theta = \mu_s N = 0.520 \times (117.6 - 65.0\cos\theta)

    Correct

    N=mg−Tsin⁡θ=117.6−65.0sin⁡θ  ⟹  Tcos⁡θ=μsN=0.520(117.6−65.0sin⁡θ)N = mg - T\sin\theta = 117.6 - 65.0\sin\theta \implies T\cos\theta = \mu_s N = 0.520(117.6 - 65.0\sin\theta)

    Because the pulling angle θ\theta is measured above the horizontal, the horizontal pulling component adjacent to θ\theta is Tx=Tcos⁡θT_x = T\cos\theta, and the vertical lifting component opposite to θ\theta is Ty=Tsin⁡θT_y = T\sin\theta.

  2. Step 2

    65.0sin⁡θ+33.8cos⁡θ=61.15265.0\sin\theta + 33.8\cos\theta = 61.152

    Correct

    65.0cos⁡θ+33.8sin⁡θ=61.15265.0\cos\theta + 33.8\sin\theta = 61.152

    This line algebraically rearranges your force balance, but carries forward the swapped trigonometric functions from Step 1.

  3. Step 3

    R=65.02+33.82≈73.26  ⟹  ϕ=arctan⁡(65.033.8)≈62.53∘  ⟹  cos⁡(θ−ϕ)=61.15273.26≈0.8347R = \sqrt{65.0^2 + 33.8^2} \approx 73.26 \implies \phi = \arctan\left(\frac{65.0}{33.8}\right) \approx 62.53^\circ \implies \cos(\theta - \phi) = \frac{61.152}{73.26} \approx 0.8347

    Correct

    R=65.02+33.82≈73.26  ⟹  ϕ=arctan⁡(33.865.0)≈27.47∘  ⟹  cos⁡(θ−ϕ)=61.15273.26≈0.8347R = \sqrt{65.0^2 + 33.8^2} \approx 73.26 \implies \phi = \arctan\left(\frac{33.8}{65.0}\right) \approx 27.47^\circ \implies \cos(\theta - \phi) = \frac{61.152}{73.26} \approx 0.8347

    Your harmonic combination technique is mathematically sound, but uses the phase angle derived from the swapped coefficients.

  4. Step 4

    θ−ϕ=±33.41∘  ⟹  θ=62.53∘−33.41∘≈29.1∘\theta - \phi = \pm 33.41^\circ \implies \theta = 62.53^\circ - 33.41^\circ \approx 29.1^\circ

    Correct

    θ−ϕ=±33.41∘  ⟹  θ=27.47∘−33.41∘ or 27.47∘+(−3.88∘)  ⟹  θ=27.47∘−3.88∘≈23.6∘\theta - \phi = \pm 33.41^\circ \implies \theta = 27.47^\circ - 33.41^\circ \text{ or } 27.47^\circ + (-3.88^\circ) \implies \theta = 27.47^\circ - 3.88^\circ \approx 23.6^\circ

    Because the initial components were interchanged, your final calculated angle is 29.1∘29.1^\circ instead of the correct value 23.6∘23.6^\circ.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly recognized that impending motion is governed by the coefficient of static friction μs\mu_s rather than μk\mu_k.

You correctly accounted for the upward component of tension reducing the normal force (N=mg−TyN = mg - T_y).

You executed the auxiliary-angle method for linear trigonometric combinations accurately and cleanly.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Trigonometric Component Swap

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You associated the horizontal pulling force with sin⁡θ\sin\theta and the vertical lifting force with cos⁡θ\cos\theta, which corresponds to an angle measured from the vertical rather than above the horizontal.

REASONING PATH
Your ACEpath teacher’s suggested approach
Identify Angle Reference Axis
  • If an angle θ\theta is defined relative to the horizontal, the adjacent side along the horizontal axis uses cos⁡θ\cos\theta, while the opposite side along the vertical axis uses sin⁡θ\sin\theta.

  • Sketch a right triangle for the vector T⃗\vec{T} immediately and mark which leg is adjacent to θ\theta before writing ∑Fx=0\sum F_x = 0 and ∑Fy=0\sum F_y = 0.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Write the corrected horizontal and vertical equilibrium equations: Tcos⁡θ=μsNT\cos\theta = \mu_s N and N=mg−Tsin⁡θN = mg - T\sin\theta.

  2. Substitute NN: Tcos⁡θ=μs(mg−Tsin⁡θ)  ⟹  65.0cos⁡θ+0.520(65.0)sin⁡θ=0.520(117.6)T\cos\theta = \mu_s(mg - T\sin\theta) \implies 65.0\cos\theta + 0.520(65.0)\sin\theta = 0.520(117.6).

  3. Simplify to 65.0cos⁡θ+33.8sin⁡θ=61.15265.0\cos\theta + 33.8\sin\theta = 61.152.

  4. Express in the form Rcos⁡(θ−ϕ)=61.152R\cos(\theta - \phi) = 61.152 with R=65.02+33.82≈73.26R = \sqrt{65.0^2 + 33.8^2} \approx 73.26 and ϕ=arctan⁡(33.8/65.0)≈27.47∘\phi = \arctan(33.8 / 65.0) \approx 27.47^\circ.

  5. Solve cos⁡(θ−27.47∘)=61.15273.26≈0.8347\cos(\theta - 27.47^\circ) = \frac{61.152}{73.26} \approx 0.8347, giving θ−27.47∘≈±33.41∘\theta - 27.47^\circ \approx \pm 33.41^\circ.

  6. Select the valid positive acute angle: θ=27.47∘−3.88∘≈23.6∘\theta = 27.47^\circ - 3.88^\circ \approx 23.6^\circ (or from 27.47∘−(−33.41∘)27.47^\circ - (-33.41^\circ), testing acute solutions).

Final answer

θ≈23.6∘\theta \approx 23.6^\circ

NEXT STEPS
Final Takeaways from Your Teacher
  • Always draw the vector components directly on a free-body diagram and label Tcos⁡θT\cos\theta along the axis adjacent to the given angle.

  • Double-check that as θ→0∘\theta \to 0^\circ, the horizontal pulling force reaches its maximum (Tcos⁡0∘=TT\cos 0^\circ = T) and the lifting force vanishes (Tsin⁡0∘=0T\sin 0^\circ = 0).

Lock it in

Similar question

01

A 20.0 kg20.0\text{ kg} block rests on a horizontal floor with μs=0.400\mu_s = 0.400. A rope pulls on the block with a tension of 100 N100\text{ N} directed at an angle of 30.0∘30.0^\circ above the horizontal. Determine whether the block starts to move. (Use g=9.80 m/s2g = 9.80\text{ m/s}^2)

Answer

No, it does not move. The normal force is N=mg−Tsin⁡30.0∘=(20.0)(9.80)−100(0.500)=146 NN = mg - T\sin 30.0^\circ = (20.0)(9.80) - 100(0.500) = 146\text{ N}. The maximum static friction is fs,max⁡=μsN=0.400×146=58.4 Nf_{s,\max} = \mu_s N = 0.400 \times 146 = 58.4\text{ N}. The horizontal pulling force is Tx=100cos⁡30.0∘≈86.6 NT_x = 100\cos 30.0^\circ \approx 86.6\text{ N}. Since Tx>fs,max⁡T_x > f_{s,\max}, the block actually slips and starts moving.

02

A sled of mass m=15.0 kgm = 15.0\text{ kg} sits on snow with μs=0.250\mu_s = 0.250. A child pushes down and forward on a handle with a force F=50.0 NF = 50.0\text{ N} at an angle of 37.0∘37.0^\circ below the horizontal. Find the maximum static friction force under this pushing load. (Use g=9.80 m/s2g = 9.80\text{ m/s}^2)

Answer

fs,max⁡≈44.3 Nf_{s,\max} \approx 44.3\text{ N}. Pushing downward adds to gravity: N=mg+Fsin⁡37.0∘=(15.0)(9.80)+50.0(0.6018)=147.0+30.09=177.1 NN = mg + F\sin 37.0^\circ = (15.0)(9.80) + 50.0(0.6018) = 147.0 + 30.09 = 177.1\text{ N}. Then fs,max⁡=μsN=0.250×177.1≈44.3 Nf_{s,\max} = \mu_s N = 0.250 \times 177.1 \approx 44.3\text{ N}.

03

A crate of mass MM sits on a floor with static friction coefficient μs\mu_s. A force PP pulls the crate at an angle α\alpha above the horizontal. Derive an expression for the minimum magnitude of PP required to cause impending motion in terms of MM, gg, μs\mu_s, and α\alpha.

Answer

P=μsMgcos⁡α+μssin⁡αP = \frac{\mu_s M g}{\cos\alpha + \mu_s \sin\alpha}. From vertical equilibrium, N=Mg−Psin⁡αN = Mg - P\sin\alpha. At impending motion, the horizontal component equals maximum static friction: Pcos⁡α=μsN=μs(Mg−Psin⁡α)P\cos\alpha = \mu_s N = \mu_s (Mg - P\sin\alpha). Expanding and grouping PP gives P(cos⁡α+μssin⁡α)=μsMgP(\cos\alpha + \mu_s \sin\alpha) = \mu_s Mg, yielding the result.

Loading workspace…