Resources

A worker uses an adjustable ramp to unload a heavy metallic component of mass m=40.0 kgm = 40.0\text{ kg}. The coefficient of static friction between the component and the ramp surface is μs=0.550\mu_s = 0.550, and the coefficient of kinetic friction is μk=0.420\mu_k = 0.420. The ramp is slowly tilted upward from the horizontal until the component is on the verge of slipping. Taking g=9.80 m/s2g = 9.80\text{ m/s}^2, determine: (a) the critical threshold angle θc\theta_c (in degrees) at which impending slip occurs, and (b) the magnitude of the static frictional force acting on the component when the incline is set to an angle of θ=20.0∘\theta = 20.0^\circ, safely below this threshold.

Answer and steps

Final answer

(a) θc=28.8∘\theta_c = 28.8^\circ; (b) fs=134 Nf_s = 134\text{ N}.

Steps

Part (a): Finding the Critical Incline Angle θc\theta_c

When a block rests on an inclined plane of angle θ\theta, gravity exerts a downward force of magnitude W=mgW = mg. Decomposing this weight into directions perpendicular and parallel to the incline gives:

  • Perpendicular component: W⊥=mgcos⁡θW_\perp = mg \cos\theta
  • Parallel (downhill) component: W∥=mgsin⁡θW_\parallel = mg \sin\theta

Because there is no motion perpendicular to the ramp surface, the normal force NN balances W⊥W_\perp: N=mgcos⁡θN = mg \cos\theta

To prevent the block from sliding down the ramp, the static frictional force fsf_s acts uphill, balancing W∥W_\parallel: fs=mgsin⁡θf_s = mg \sin\theta

As the incline angle increases, mgsin⁡θmg \sin\theta grows larger, requiring a larger static frictional force to maintain equilibrium. Slip is impending when static friction reaches its maximum possible value: fs,max⁡=μsN=μsmgcos⁡θcf_{s,\max} = \mu_s N = \mu_s mg \cos\theta_c

Setting the downhill force equal to this maximum static friction: mgsin⁡θc=μsmgcos⁡θcmg \sin\theta_c = \mu_s mg \cos\theta_c

Dividing both sides by mgcos⁡θcmg \cos\theta_c: tan⁡θc=μs\tan\theta_c = \mu_s

Substitute μs=0.550\mu_s = 0.550: θc=arctan⁡(0.550)≈28.81∘≈28.8∘\theta_c = \arctan(0.550) \approx 28.81^\circ \approx 28.8^\circ


Part (b): Calculating Static Friction at θ=20.0∘\theta = 20.0^\circ

At an angle of θ=20.0∘\theta = 20.0^\circ, the angle is less than the critical threshold (θ<θc\theta < \theta_c), meaning the component remains stationary and does not slip.

Key Pitfall: The formula fs=μsNf_s = \mu_s N applies only at the verge of slipping (fs,max⁡f_{s,\max}). When an object is securely at rest, static friction is a self-adjusting reaction force that balances the net applied force along the surface, satisfying fs≤μsNf_s \le \mu_s N.

Applying Newton's first law along the plane (ΣF∥=0\Sigma F_\parallel = 0): fs=mgsin⁡θf_s = mg \sin\theta

Substitute the given values: fs=(40.0 kg)(9.80 m/s2)sin⁡(20.0∘)f_s = (40.0\text{ kg})(9.80\text{ m/s}^2) \sin(20.0^\circ) fs=(392 N)(0.3420)≈134 Nf_s = (392\text{ N})(0.3420) \approx 134\text{ N}

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student calculates the static friction force using the maximum static friction formula fs = μs * N rather than recognizing that actual static friction adjusts to balance the parallel component of gravity when the object is at rest below the threshold angle.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    tan⁡(θc)=μs=0.550  ⟹  θc=arctan⁡(0.550)=28.8∘\tan(\theta_c) = \mu_s = 0.550 \implies \theta_c = \arctan(0.550) = 28.8^\circ

  2. Step 2

    N=m⋅g⋅cos⁡(20.0∘)  ⟹  N=40.0⋅9.80⋅cos⁡(20.0∘)=368.35 NN = m \cdot g \cdot \cos(20.0^\circ) \implies N = 40.0 \cdot 9.80 \cdot \cos(20.0^\circ) = 368.35\text{ N}

  3. Step 3

    fs=μs⋅N  ⟹  fs=0.550⋅368.35=203 Nf_s = \mu_s \cdot N \implies f_s = 0.550 \cdot 368.35 = 203\text{ N}

    Correct

    fs=mgsin⁡(20.0∘)=(40.0 kg)(9.80 m/s2)sin⁡(20.0∘)≈134 Nf_s = mg\sin(20.0^\circ) = (40.0\text{ kg})(9.80\text{ m/s}^2)\sin(20.0^\circ) \approx 134\text{ N}

    Because θ=20.0∘<θc=28.8∘\theta = 20.0^\circ < \theta_c = 28.8^\circ, the component is stationary and not on the verge of slipping. Static friction acts as an equilibrium reaction force balancing gravity parallel to the incline (fs=mgsin⁡θf_s = mg\sin\theta), satisfying the inequality fs≤μsNf_s \le \mu_s N rather than equaling μsN\mu_s N.

WHAT YOU DID WELL
Compliments from Your Teacher

You used the correct trigonometric relation tan⁡θc=μs\tan\theta_c = \mu_s to find the critical tipping angle.

You set up and evaluated the perpendicular normal force component correctly.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Equating static friction directly to its maximum limit

You treated static friction as a fixed value calculated from μsN\mu_s N rather than an adjustable balancing force.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing the upper bound for static friction (fs,max⁡=μsNf_{s,\max} = \mu_s N) with the actual static friction (fsf_s) when an object is in static equilibrium below the slip threshold.

REASONING PATH
Your ACEpath teacher’s suggested approach
Check slip status first
  • If the angle is strictly less than the critical angle (θ<θc\theta < \theta_c), slip is not impending and fs<fs,max⁡f_s < f_{s,\max}.

  • Always compare the angle or applied force to the slip threshold before picking an equation.

Equilibrium along the surface
  • For an object at rest, static friction satisfies Newton's first law: ΣF∥=0\Sigma F_\parallel = 0.

  • Set fs=F∥,appliedf_s = F_{\parallel,\text{applied}} (here mgsin⁡θmg\sin\theta) and only use μsN\mu_s N to verify that fs≤fs,max⁡f_s \le f_{s,\max}.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Apply Newton's first law parallel to the ramp: ΣF∥=mgsin⁡(20.0∘)−fs=0\Sigma F_\parallel = mg\sin(20.0^\circ) - f_s = 0.

  2. Solve for the actual static friction: fs=mgsin⁡(20.0∘)f_s = mg\sin(20.0^\circ).

  3. Substitute the numerical values: fs=(40.0 kg)(9.80 m/s2)sin⁡(20.0∘)=392sin⁡(20.0∘)≈134 Nf_s = (40.0\text{ kg})(9.80\text{ m/s}^2)\sin(20.0^\circ) = 392\sin(20.0^\circ) \approx 134\text{ N}.

Final answer

(a) θc=28.8∘\theta_c = 28.8^\circ; (b) fs=134 Nf_s = 134\text{ N}

NEXT STEPS
Final Takeaways from Your Teacher
  • Remember that the formula f=μNf = \mu N only represents an equality for kinetic friction (fk=μkNf_k = \mu_k N) or at the absolute threshold of slipping (fs,max⁡=μsNf_{s,\max} = \mu_s N).

  • Whenever a body is stationary, find static friction directly by setting up force balance ΣF=0\Sigma F = 0 along the surface.

OverviewACEpath Teacher's Diagnosis

02 The student uses the kinetic friction coefficient instead of the static friction coefficient when determining the threshold angle for impending slip.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    tan⁡(θc)=μk=0.420  ⟹  θc=arctan⁡(0.420)=22.8∘\tan(\theta_c) = \mu_k = 0.420 \implies \theta_c = \arctan(0.420) = 22.8^\circ

    Correct

    tan⁡(θc)=μs=0.550  ⟹  θc=arctan⁡(0.550)≈28.8∘\tan(\theta_c) = \mu_s = 0.550 \implies \theta_c = \arctan(0.550) \approx 28.8^\circ

    Impending slip occurs at the boundary where the object is still stationary and static friction reaches its maximum possible value (fs,max⁡=μsNf_{s,\max} = \mu_s N). Therefore, you must use the coefficient of static friction μs\mu_s, not the kinetic coefficient μk\mu_k.

  2. Step 2

    fs=m⋅g⋅sin⁡(20.0∘)  ⟹  fs=40.0⋅9.80⋅sin⁡(20.0∘)=134 Nf_s = m \cdot g \cdot \sin(20.0^\circ) \implies f_s = 40.0 \cdot 9.80 \cdot \sin(20.0^\circ) = 134\text{ N}

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly used static equilibrium along the incline to calculate the frictional force when the object is resting below the critical angle.

You accurately substituted values and evaluated trigonometric functions with correct units.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Kinetic vs. static friction confusion

You selected μk=0.420\mu_k = 0.420 rather than μs=0.550\mu_s = 0.550 when setting up the impending slip condition tan⁡θc=μ\tan\theta_c = \mu.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing the condition for the verge of motion (impending slip) with ongoing motion. Impending slip is the uppermost boundary of static friction, governed by μs\mu_s, whereas kinetic friction (μk\mu_k) only acts once surfaces are already sliding relative to each other.

REASONING PATH
Your ACEpath teacher’s suggested approach
State of motion check
  • Before choosing a friction coefficient, ask: Are the contact surfaces sliding, or are they stationary?

  • If stationary (including at the very verge of sliding), use μs\mu_s. If actively sliding, use μk\mu_k.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Set the downhill force equal to maximum static friction: mgsin⁡θc=fs,max⁡=μsN=μsmgcos⁡θcmg\sin\theta_c = f_{s,\max} = \mu_s N = \mu_s mg\cos\theta_c.

  2. Divide by mgcos⁡θcmg\cos\theta_c to obtain tan⁡θc=μs\tan\theta_c = \mu_s.

  3. Substitute μs=0.550\mu_s = 0.550: θc=arctan⁡(0.550)≈28.8∘\theta_c = \arctan(0.550) \approx 28.8^\circ.

Final answer

(a) θc=28.8∘\theta_c = 28.8^\circ; (b) fs=134 Nf_s = 134\text{ N}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the physical distinction between static friction (fs≤μsNf_s \le \mu_s N) and kinetic friction (fk=μkNf_k = \mu_k N).

  • Practice identifying whether a system is stationary, on the verge of sliding, or in continuous relative motion.

OverviewACEpath Teacher's Diagnosis

03 The student swaps the trigonometric functions for the parallel and perpendicular force components, using cosine instead of sine for the parallel component of gravity.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    tan⁡(θc)=μs=0.550  ⟹  θc=arctan⁡(0.550)=28.8∘\tan(\theta_c) = \mu_s = 0.550 \implies \theta_c = \arctan(0.550) = 28.8^\circ

  2. Step 2

    fs=m⋅g⋅cos⁡(20.0∘)=40.0⋅9.80⋅cos⁡(20.0∘)=368 Nf_s = m \cdot g \cdot \cos(20.0^\circ) = 40.0 \cdot 9.80 \cdot \cos(20.0^\circ) = 368\text{ N}

    Correct

    fs=mgsin⁡(20.0∘)=(40.0)(9.80)sin⁡(20.0∘)≈134 Nf_s = mg\sin(20.0^\circ) = (40.0)(9.80)\sin(20.0^\circ) \approx 134\text{ N}

    Along the incline, the downhill component of gravity is opposite to the angle θ\theta from the normal, so it is given by mgsin⁡θmg\sin\theta, not mgcos⁡θmg\cos\theta. Because the block is stationary, static friction must balance this downhill force: fs=mgsin⁡θf_s = mg\sin\theta.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly related the critical angle of repose to the coefficient of static friction using tan⁡θc=μs\tan\theta_c = \mu_s.

You accurately computed the numerical angle θc=28.8∘\theta_c = 28.8^\circ from the given static friction coefficient.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Trigonometric component swap on inclined plane

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You swapped the trigonometric functions for resolving gravity along and perpendicular to the incline, taking mgcos⁡θmg\cos\theta rather than mgsin⁡θmg\sin\theta as the downhill component parallel to the ramp.

REASONING PATH
Your ACEpath teacher’s suggested approach
Resolve Weight Along the Ramp
  • When an incline is angled at θ\theta above the horizontal, the component of gravity pulling parallel (downhill) is W∥=mgsin⁡θW_\parallel = mg\sin\theta, and the perpendicular component pressing into the ramp is W⊥=mgcos⁡θW_\perp = mg\cos\theta.

  • Always draw the right triangle formed by the weight vector and the ramp surface; note that θ\theta lies between the vertical weight vector and the normal axis.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Write Newton's first law along the incline: ΣF∥=mgsin⁡θ−fs=0\Sigma F_\parallel = mg\sin\theta - f_s = 0.

  2. Isolate static friction: fs=mgsin⁡θf_s = mg\sin\theta.

  3. Substitute the values: fs=(40.0 kg)(9.80 m/s2)sin⁡(20.0∘)≈134 Nf_s = (40.0\text{ kg})(9.80\text{ m/s}^2)\sin(20.0^\circ) \approx 134\text{ N}.

Final answer

(a) θc=28.8∘\theta_c = 28.8^\circ; (b) fs=134 Nf_s = 134\text{ N}

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice sketching free-body diagrams on ramps and verifying components with limit checks: as θ→0∘\theta \to 0^\circ, parallel force should vanish (mgsin⁡0∘=0mg\sin 0^\circ = 0).

  • Review the distinction between the normal force (N=mgcos⁡θN = mg\cos\theta) and the downhill gravity component (W∥=mgsin⁡θW_\parallel = mg\sin\theta).

Lock it in

Similar question

01

A 25.0 kg25.0\text{ kg} crate rests on a horizontal floor where μs=0.400\mu_s = 0.400. A worker pulls horizontally with a force of 60.0 N60.0\text{ N}. Taking g=9.80 m/s2g = 9.80\text{ m/s}^2, determine the magnitude of the static friction force.

Answer

fs=60.0 Nf_s = 60.0\text{ N}. The maximum static friction is fs,max⁡=μsmg=(0.400)(25.0)(9.80)=98.0 Nf_{s,\max} = \mu_s mg = (0.400)(25.0)(9.80) = 98.0\text{ N}. Since the applied force 60.0 N<98.0 N60.0\text{ N} < 98.0\text{ N}, the crate remains stationary, so fs=Fpull=60.0 Nf_s = F_{\text{pull}} = 60.0\text{ N}.

02

A 15.0 kg15.0\text{ kg} block sits on an incline tilted at θ=15.0∘\theta = 15.0^\circ. The coefficients of friction are μs=0.450\mu_s = 0.450 and μk=0.350\mu_k = 0.350. Taking g=9.80 m/s2g = 9.80\text{ m/s}^2, find the magnitude of the friction force acting on the block.

Answer

fs=38.0 Nf_s = 38.0\text{ N}. The critical angle is θc=arctan⁡(0.450)≈24.2∘\theta_c = \arctan(0.450) \approx 24.2^\circ. Since 15.0∘<24.2∘15.0^\circ < 24.2^\circ, the block is securely at rest. Static friction balances the downhill component of gravity: fs=mgsin⁡(15.0∘)=(15.0)(9.80)sin⁡(15.0∘)≈38.0 Nf_s = mg\sin(15.0^\circ) = (15.0)(9.80)\sin(15.0^\circ) \approx 38.0\text{ N}.

03

A 12.0 kg12.0\text{ kg} block on a 25.0∘25.0^\circ incline is held at rest by friction alone (μs=0.600\mu_s = 0.600, μk=0.450\mu_k = 0.450). A worker pushes horizontally into the ramp face with an extra perpendicular force of Fpush=50.0 NF_{\text{push}} = 50.0\text{ N} (normal to the slope). Taking g=9.80 m/s2g = 9.80\text{ m/s}^2, what is the friction force acting on the block?

Answer

fs=49.7 Nf_s = 49.7\text{ N}. Increasing the normal force increases the available maximum static friction capacity (fs,max⁡=μs(mgcos⁡θ+Fpush)f_{s,\max} = \mu_s(mg\cos\theta + F_{\text{push}})), but the parallel downhill force remains unchanged at mgsin⁡(25.0∘)=(12.0)(9.80)sin⁡(25.0∘)≈49.7 Nmg\sin(25.0^\circ) = (12.0)(9.80)\sin(25.0^\circ) \approx 49.7\text{ N}. Since the block remains at rest, fs=49.7 Nf_s = 49.7\text{ N}.

Loading workspace…