Resources
In a laboratory physics experiment using an inclined air track, a glider of mass is held at rest against a release latch. The air track is inclined at an angle above horizontal. Two photogates, Gate 1 and Gate 2, are positioned along the track separated by a distance . A flag of length mounted on the glider interrupts each photogate. Gate 1 records a transit time , and Gate 2 records a transit time . Setting Gate 1 as the reference level (): (a) Calculate the vertical drop between Gate 1 and Gate 2 and the corresponding change in gravitational potential energy . (b) Using the photogate data, calculate the kinetic energy of the glider at Gate 1 () and at Gate 2 (). (c) Calculate the net change in mechanical energy and express the energy dissipated due to residual air resistance as a percentage of the initial mechanical energy at Gate 1. Use .
Answer and steps
Final answer
(a) , ; (b) , ; (c) , representing an energy dissipation of relative to the potential energy released ( relative to ).
Steps
Part (a): Vertical Drop and Change in Gravitational Potential Energy
The glider travels down an air track inclined at an angle over a distance between Gate 1 and Gate 2.
- Calculate the vertical drop (): Since the glider moves downward, its vertical displacement is negative:
- Calculate the change in gravitational potential energy (): Using :
(Pitfall: Ensure the track angle is used with the sine function, as the vertical leg is opposite the incline angle, and remember that dropping in elevation corresponds to a negative change in potential energy.)
Part (b): Kinetic Energy at Each Photogate
The instantaneous speed at each gate is approximated by the average speed of the flag of length during its transit time .
- At Gate 1:
- At Gate 2:
Part (c): Net Change in Mechanical Energy and Dissipation
- Calculate the change in mechanical energy (): The gain in kinetic energy is: The net change in mechanical energy is: The negative value indicates that of mechanical energy was dissipated, primarily due to residual air resistance.
-
Express energy dissipation as a percentage:
- Relative to total mechanical energy available at Gate 1 (taking Gate 2 as the reference height where ):
- Relative to initial kinetic energy :
Typical errors
01 The student misapplies trigonometry by using cos θ instead of sin θ when determining the vertical height drop along the incline.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
The track is inclined at an angle relative to the horizontal. In the right triangle formed by the track length and the ground, the vertical displacement is opposite to the angle , so you must use , not . Multiplying by yields the horizontal displacement.
- Step 2
- Step 3Correct
Your formula structure was conceptually sound, but the numerical result was thrown off by the incorrect value of propagated from part (a).
WHAT YOU DID WELL
Compliments from Your TeacherYou converted the photogate flag length from centimeters to meters accurately.
You correctly used the photogate transit times to find the linear velocities at both stations.
You correctly calculated the kinetic energy values using .
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou set the vertical drop as rather than .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou confused the adjacent and opposite sides of an incline triangle. When an incline angle is measured relative to the horizontal ground, the vertical height corresponds to the opposite side (requiring ), while the horizontal distance along the ground corresponds to the adjacent side (requiring ).
REASONING PATH
Your ACEpath teacher’s suggested approach- Check Angle Reference
If the angle is given above the horizontal, the vertical height is opposite to : .
Always sketch the right triangle and label the hypotenuse , opposite side , and adjacent base before choosing a trigonometric ratio.
- Sanity Check Extreme Angles
As the incline angle approaches (flat ground), the vertical drop must approach zero: , whereas .
Mentally test . A nearly horizontal track () cannot have a vertical drop nearly equal to its full length ().
CORRECTED PATH
ACEpath Teacher's DemonstrationCalculate the vertical drop using the sine function: .
Compute the change in gravitational potential energy: .
Calculate the net change in mechanical energy: .
Compute the percentage dissipated relative to total initial energy: .
(a) , ; (b) , ; (c) , representing of available energy dissipated ( relative to ).
02 The student forgets to square the velocity when evaluating the kinetic energy formula, computing K = (1/2)mv.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
You calculated the transit speed correctly, but you forgot to square the speed when evaluating the kinetic energy formula .
- Step 3Correct
You determined the speed at Gate 2 accurately, but you omitted the exponent on again, calculating instead of .
- Step 4Correct
Your setup for mechanical energy change followed your calculated kinetic energy values, but the numerical result was thrown off by the unsquared velocities from part (b).
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly resolved the incline geometry to determine the vertical displacement.
You properly applied the formula for change in gravitational potential energy.
You accurately found the instantaneous velocities from the photogate transit times.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou wrote instead of squaring the speed, which caused kinetic energy to have units of momentum rather than energy.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisIncomplete execution of the kinetic energy definition , leading to a linear velocity substitution rather than a quadratic one.
REASONING PATH
Your ACEpath teacher’s suggested approach- Formula Recall
Kinetic energy is quadratic with speed: .
Always write down the algebraic formula with the exponent before plugging in numerical values.
- Dimensional Verification
Energy must have units of Joules: .
Check your units during substitution: is momentum (), whereas gives energy ().
CORRECTED PATH
ACEpath Teacher's DemonstrationCalculate .
Calculate .
Compute .
Find .
Calculate percentage dissipated relative to total available energy: .
(a) , ; (b) , ; (c) , dissipated
03 The student neglects the unit conversion of the flag length from centimeters to meters, using d = 2.50 instead of 0.0250 m.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
,
Correct;
You forgot to convert the flag length into SI units of meters (). Using centimeters directly resulted in unrealistically high speeds and kinetic energies.
- Step 3Correct
Your formula structure for mechanical energy change is appropriate, but the numerical result is heavily distorted by the unscaled kinetic energy values from step 2.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly used trigonometry to relate the travel distance along the incline to the vertical drop.
You recognized that moving downhill results in a negative change in gravitational potential energy.
You correctly set up the relationship between flag transit time and instantaneous speed.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou substituted the flag length as instead of .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisOverlooking standard base SI unit consistency () before computing quantities that involve derived units like Joules ().
REASONING PATH
Your ACEpath teacher’s suggested approach- Unit Consistency in Energy Calculations
The Joule is defined in base SI units as . All lengths must be in meters.
Always convert centimeters to meters () before calculating velocity or energy.
- Physical Reality Check
A laboratory glider on an air track typically moves at speeds between and .
Inspect calculated speeds: (over ) is an immediate clue that a centimeter-to-meter conversion was missed.
CORRECTED PATH
ACEpath Teacher's DemonstrationConvert flag length to meters: .
Calculate speeds: and .
Calculate kinetic energies: , .
Calculate mechanical energy change: .
Compute percentage dissipated relative to total initial energy: .
(a) , ; (b) , ; (c) , dissipation (or relative to )
Lock it in
For an object moving a distance along an incline angled at above the horizontal, which trigonometric expression gives the vertical height change ?
. The vertical side is opposite the angle measured from the horizontal ground.
Similar question
A block slides down a frictionless ramp inclined at above the horizontal. Calculate the change in gravitational potential energy of the block. (Use )
Answer
. Thus, .
A glider starts from rest at the top of an air track inclined at to the horizontal. After traveling down the track, a photogate with flag length records a transit time of . Determine the mechanical energy lost to friction and air drag over this distance. (Use )
Answer
Vertical drop: . Potential energy lost: . Speed at photogate: . Final kinetic energy: . Energy lost: .
A toy car of mass is launched up an incline of angle with an initial speed of . It travels a distance along the track before coming momentarily to rest. If of mechanical energy is dissipated by friction during the climb, find the distance traveled along the track. (Use )
Answer
Initial kinetic energy: . At the stopping point, mechanical energy conservation with friction gives . Since , we have . The distance along the incline is .