Resources
A heavy flywheel storage system of rotational inertia is accelerated from rest to an angular speed by an electric drive requiring . The system then discharges stored energy to drive an external mechanical load while being subjected to a retarding frictional torque modeled as , where . (a) Calculate the charging mechanical efficiency of the flywheel. (b) If the system delivers mechanical work to an external load over an extended asymptotic deceleration period where angular speed decays exponentially from toward according to , determine the theoretical maximum work that can be extracted if an external resistive torque absorbs a constant fraction of the total dissipated power at all times.
Answer and steps
Final answer
(a) ; (b)
Steps
Part (a): Charging Mechanical Efficiency
-
Calculate the rotational kinetic energy stored in the flywheel:
The kinetic energy of a rotating body with moment of inertia at angular velocity is given by:Substituting the given values:
-
Compute the charging efficiency:
The mechanical charging efficiency is the ratio of stored kinetic energy to the electrical energy input :Expressed as a percentage to three significant figures:
Part (b): Theoretical Maximum Work Extracted by the External Load
- Relate power dissipation to total energy loss:
As the flywheel decelerates from to , the total mechanical energy released by the flywheel is entirely converted into work and thermal dissipation: - Apply the power fraction:
At any instant , the rate at which energy is delivered to the external load (power ) is a constant fraction of the total instantaneous dissipated power : -
Integrate over the entire deceleration period:
Integrating the power over the entire deceleration interval from to :Substituting the known values:
Common Pitfall: There is no need to perform explicit time integration of . Because the instantaneous external fraction is strictly constant across the entire discharge, the total extracted energy is simply times the total stored kinetic energy.
Typical errors
01 The student forgets the factor of 1/2 in the rotational kinetic energy formula, leading to an impossible efficiency greater than 1.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
You forgot the factor of in the rotational kinetic energy expression, doubling the actual stored energy.
- Step 2Correct
Your ratio setup for efficiency was correct, but substituting the doubled energy yielded an impossible efficiency greater than ().
- Step 3
- Step 4
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly recognized that the efficiency is the ratio of stored rotational energy to input energy.
You correctly identified and applied the factor of in part (b) when calculating the energy released by the flywheel.
You recognized that with a constant instantaneous fraction , total extracted work is simply times total stored energy.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeMissing the coefficient in .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou temporarily confused rotational kinetic energy with instead of maintaining its exact analogy to translational kinetic energy , and you missed the sanity check that real-world mechanical efficiency must be less than ().
REASONING PATH
Your ACEpath teacher’s suggested approach- Kinetic Energy Pre-factor Check
in translation, and in rotation.
Always verify the factor of whenever calculating kinetic energy from mass/inertia and speed.
- Efficiency Sanity Check
For passive mechanical systems without an internal energy source, efficiency must satisfy ().
If an efficiency calculation yields a value greater than , immediately recheck your numerator for an omitted factor or unit error.
CORRECTED PATH
ACEpath Teacher's DemonstrationWrite the complete rotational kinetic energy formula: .
Substitute the values: .
Compute the charging efficiency: .
(a) ; (b) $W_{,\max} = 7.83 10^5_
02 The student omits squaring the angular velocity when computing the stored rotational kinetic energy, vastly underestimating the energy stored.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
You forgot to square the angular velocity in the rotational kinetic energy formula. Rotational kinetic energy depends on , giving rather than .
- Step 2Correct
Your efficiency definition and substitution step were set up correctly, but the numerical result was affected by the underestimated value of from Step 1.
- Step 3
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly set up the efficiency equation as useful stored energy divided by input energy.
You recognized in part (b) that total extracted work equals the constant fraction multiplied by the total released rotational energy.
You used the correct rotational kinetic energy formula in part (b).
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou wrote instead of in part (a), even though you knew the correct formula in part (b).
WHY IT HAPPENED
ACEpath Teacher's DiagnosisIn linear mechanics, momentum is while kinetic energy is . Similarly, angular momentum is while kinetic energy is . Mixing up rotational momentum and energy expressions can lead to omitting the square on .
REASONING PATH
Your ACEpath teacher’s suggested approach- Dimensional and Formula Check for Kinetic Energy
Kinetic energy always involves the square of speed: and .
Before calculating, verify units: . A single power of yields units of angular momentum (), not energy.
CORRECTED PATH
ACEpath Teacher's DemonstrationCompute the stored rotational kinetic energy with the squared angular speed: .
Divide by the input electrical energy to find efficiency: or .
(a) ; (b)
03 The student misinterprets the external fraction k_ext as being applied to the input electrical energy rather than the stored mechanical kinetic energy of the flywheel.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
During discharge, the flywheel only has of mechanical energy available. The external extraction fraction partitions the mechanical power dissipated as the wheel decelerates, so it must multiply , not the initial electrical input .
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly computed the rotational kinetic energy of the flywheel at maximum angular speed.
You set up and evaluated the mechanical charging efficiency ratio correctly.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou multiplied the extraction fraction by the electrical input instead of the stored kinetic energy .
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConflating two distinct operating phases (charge vs. discharge). The input energy was supplied from the electrical grid during the charging cycle, with part of it already lost as heat. During discharge, the only energy pool present in the system is the stored mechanical energy .
REASONING PATH
Your ACEpath teacher’s suggested approach- Identify the Active Energy Pool
Energy extracted during discharge cannot exceed or draw directly from pre-conversion inputs of an earlier cycle.
Check that work extracted during discharge is partitioned from the stored energy , not the total electrical input .
- Sanity Check via Conservation of Energy
Extracted mechanical work must satisfy .
Compare against ; notice that outputting more work than stored kinetic energy violates the first law of thermodynamics.
CORRECTED PATH
ACEpath Teacher's DemonstrationIdentify the total energy available during discharge as .
Integrate external power over time: .
Multiply: .
(a) ; (b)
Lock it in
What is the formula for the rotational kinetic energy of a rigid body rotating about a fixed axis with moment of inertia and angular speed ?
. Remember the factor, directly analogous to linear kinetic energy .
Similar question
A solid cylindrical rotor has rotational inertia . It is spun up from rest to an angular speed using an electrical input of . Calculate the charging efficiency .
Answer
. The charging efficiency is .
A flywheel system with stored rotational kinetic energy is coupled to a generator that extracts useful electrical work while bearing friction dissipates energy as heat. If the instantaneous generator load power is always three times the instantaneous frictional power dissipation (), how much total electrical energy can be generated as the flywheel comes completely to rest?
Answer
The fraction of total power converted to electricity is . Integrating over the entire deceleration period gives .
An electric motor with electrical-to-mechanical conversion efficiency accelerates a flywheel of inertia from rest to . The flywheel subsequently discharges all its stored energy into a mechanical winch with discharge efficiency . (a) Determine the initial electrical energy required. (b) Determine the net round-trip efficiency of the entire storage cycle.
Answer
(a) Stored energy is . Electrical input needed is . (b) Extracted mechanical work is . Net round-trip efficiency is .