Resources

A standardized micro-tensile test is conducted on an ultra-thin orthodontic wire segment. The specimen has a rectangular cross section with thickness t=380 μmt = 380\text{ }\mu\text{m} and width w=0.650 mmw = 0.650\text{ mm}, and an initial active gauge length of L0=25.0 mmL_0 = 25.0\text{ mm}. When an axial pulling force of F=42.5 NF = 42.5\text{ N} is applied, an optical sensor records an elongation of ΔL=68.0 μm\Delta L = 68.0\text{ }\mu\text{m}. First, convert all geometric dimensions to base SI units (mm and m2m^2). Then calculate: (a) the tensile stress in megapascals (MPa\text{MPa}), (b) the dimensionless tensile strain expressed both as a decimal and in microstrain (με\mu\varepsilon), and (c) the Young's modulus of the wire material in gigapascals (GPa\text{GPa}).

Answer and steps

Final answer

(a) σ=172 MPa\sigma = 172\text{ MPa}; (b) ε=2.72×10−3=2720 με\varepsilon = 2.72 \times 10^{-3} = 2720\text{ }\mu\varepsilon; (c) E=63.3 GPaE = 63.3\text{ GPa}

Steps

01

Convert all geometric values to base SI units

Convert micrometers (μm\mu\text{m}) and millimeters (mm\text{mm}) into meters (m\text{m}):

  • Thickness: t=380 μm=380×10−6 m=3.80×10−4 mt = 380\text{ }\mu\text{m} = 380 \times 10^{-6}\text{ m} = 3.80 \times 10^{-4}\text{ m}
  • Width: w=0.650 mm=0.650×10−3 m=6.50×10−4 mw = 0.650\text{ mm} = 0.650 \times 10^{-3}\text{ m} = 6.50 \times 10^{-4}\text{ m}
  • Gauge length: L0=25.0 mm=25.0×10−3 m=2.50×10−2 mL_0 = 25.0\text{ mm} = 25.0 \times 10^{-3}\text{ m} = 2.50 \times 10^{-2}\text{ m}
  • Elongation: ΔL=68.0 μm=68.0×10−6 m=6.80×10−5 m\Delta L = 68.0\text{ }\mu\text{m} = 68.0 \times 10^{-6}\text{ m} = 6.80 \times 10^{-5}\text{ m}

Calculate the cross-sectional area AA of the rectangular wire: A=t⋅w=(3.80×10−4 m)⋅(6.50×10−4 m)=2.47×10−7 m2A = t \cdot w = (3.80 \times 10^{-4}\text{ m}) \cdot (6.50 \times 10^{-4}\text{ m}) = 2.47 \times 10^{-7}\text{ m}^2


02

Calculate the tensile stress (σ\sigma)

Tensile stress is defined as the applied normal force per unit cross-sectional area: σ=FA\sigma = \frac{F}{A}

Substitute F=42.5 NF = 42.5\text{ N} and A=2.47×10−7 m2A = 2.47 \times 10^{-7}\text{ m}^2: σ=42.5 N2.47×10−7 m2≈1.7206×108 Pa\sigma = \frac{42.5\text{ N}}{2.47 \times 10^{-7}\text{ m}^2} \approx 1.7206 \times 10^8\text{ Pa}

Convert Pascals (Pa\text{Pa}) to megapascals (MPa\text{MPa}), where 1 MPa=106 Pa1\text{ MPa} = 10^6\text{ Pa}: σ=1.7206×108 Pa106 Pa/MPa≈172 MPa\sigma = \frac{1.7206 \times 10^8\text{ Pa}}{10^6\text{ Pa/MPa}} \approx 172\text{ MPa}


03

Calculate the tensile strain (ε\varepsilon)

Tensile strain is the fractional change in length along the axis of loading: ε=ΔLL0\varepsilon = \frac{\Delta L}{L_0}

Substitute ΔL=6.80×10−5 m\Delta L = 6.80 \times 10^{-5}\text{ m} and L0=2.50×10−2 mL_0 = 2.50 \times 10^{-2}\text{ m}: ε=6.80×10−5 m2.50×10−2 m=2.72×10−3\varepsilon = \frac{6.80 \times 10^{-5}\text{ m}}{2.50 \times 10^{-2}\text{ m}} = 2.72 \times 10^{-3}

To express strain in microstrain (με\mu\varepsilon), multiply the dimensionless decimal by 10610^6: ε=2.72×10−3×106 με=2720 με\varepsilon = 2.72 \times 10^{-3} \times 10^6\text{ }\mu\varepsilon = 2720\text{ }\mu\varepsilon

Pitfall: Ensure that both ΔL\Delta L and L0L_0 are in identical units before dividing; otherwise, the resulting dimensionless ratio will be off by orders of magnitude.


04

Calculate Young's modulus (EE)

Young's modulus represents the material's stiffness in the linear elastic regime and is the ratio of tensile stress to tensile strain: E=σεE = \frac{\sigma}{\varepsilon}

Using the unrounded values for accuracy: E=1.7206×108 Pa2.72×10−3≈6.326×1010 PaE = \frac{1.7206 \times 10^8\text{ Pa}}{2.72 \times 10^{-3}} \approx 6.326 \times 10^{10}\text{ Pa}

Convert Pascals (Pa\text{Pa}) to gigapascals (GPa\text{GPa}), where 1 GPa=109 Pa1\text{ GPa} = 10^9\text{ Pa}: E=6.326×1010 Pa109 Pa/GPa≈63.3 GPaE = \frac{6.326 \times 10^{10}\text{ Pa}}{10^9\text{ Pa/GPa}} \approx 63.3\text{ GPa}

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student confuses micro with milli when converting the thickness, using 10⁻³ m instead of 10⁻⁶ m, which overestimates the cross-sectional area and underestimates the resulting stress and Young's modulus.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    t=0.380 m  ⟹  w=0.650×10−3 m  ⟹  L0=25.0×10−3 m  ⟹  ΔL=68.0×10−6 m  ⟹  A=t×w=(380×10−3 m)×(0.650×10−3 m)=2.47×10−4 m2t = 0.380\text{ m} \implies w = 0.650 \times 10^{-3}\text{ m} \implies L_0 = 25.0 \times 10^{-3}\text{ m} \implies \Delta L = 68.0 \times 10^{-6}\text{ m} \implies A = t \times w = (380 \times 10^{-3}\text{ m}) \times (0.650 \times 10^{-3}\text{ m}) = 2.47 \times 10^{-4}\text{ m}^2

    Correct

    t=380×10−6 m=3.80×10−4 m  ⟹  A=(3.80×10−4 m)×(6.50×10−4 m)=2.47×10−7 m2t = 380 \times 10^{-6}\text{ m} = 3.80 \times 10^{-4}\text{ m} \implies A = (3.80 \times 10^{-4}\text{ m}) \times (6.50 \times 10^{-4}\text{ m}) = 2.47 \times 10^{-7}\text{ m}^2

    You correctly converted width ww, initial length L0L_0, and elongation ΔL\Delta L, but you converted the thickness as t=380×10−3 mt = 380 \times 10^{-3}\text{ m} instead of 380×10−6 m380 \times 10^{-6}\text{ m}. Because micro (μ\mu) represents 10−610^{-6}, this made your cross-sectional area 10001000 times too large.

  2. Step 2

    σ=FA=42.5 N2.47×10−4 m2=1.72×105 Pa=0.172 MPa\sigma = \frac{F}{A} = \frac{42.5\text{ N}}{2.47 \times 10^{-4}\text{ m}^2} = 1.72 \times 10^5\text{ Pa} = 0.172\text{ MPa}

    Correct

    σ=FA=42.5 N2.47×10−7 m2≈1.72×108 Pa=172 MPa\sigma = \frac{F}{A} = \frac{42.5\text{ N}}{2.47 \times 10^{-7}\text{ m}^2} \approx 1.72 \times 10^8\text{ Pa} = 172\text{ MPa}

    Your formula and calculation method are completely sound, but the numerical result is 10001000 times too small due to the overstated area from Step 1.

  3. Step 3

    ε=ΔLL0=68.0×10−6 m25.0×10−3 m=0.00272  ⟹  ε=2720 με\varepsilon = \frac{\Delta L}{L_0} = \frac{68.0 \times 10^{-6}\text{ m}}{25.0 \times 10^{-3}\text{ m}} = 0.00272 \implies \varepsilon = 2720\text{ }\mu\varepsilon

  4. Step 4

    E=σε=1.7206×105 Pa0.00272=6.33×107 Pa=0.0633 GPaE = \frac{\sigma}{\varepsilon} = \frac{1.7206 \times 10^5\text{ Pa}}{0.00272} = 6.33 \times 10^7\text{ Pa} = 0.0633\text{ GPa}

    Correct

    E=σε=1.7206×108 Pa2.72×10−3≈6.33×1010 Pa=63.3 GPaE = \frac{\sigma}{\varepsilon} = \frac{1.7206 \times 10^8\text{ Pa}}{2.72 \times 10^{-3}} \approx 6.33 \times 10^{10}\text{ Pa} = 63.3\text{ GPa}

    Your formula definition for Young's modulus is correct, but your final answer inherited the off-by-10001000 error from your stress value.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified and applied the fundamental definitions for tensile stress, tensile strain, and Young's modulus.

You converted millimeters into meters accurately for the width and gauge length.

You calculated the tensile strain and expressed it properly both in decimal form and in microstrain.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
SI Prefix Confusion (micro vs. milli)

You treated 1 μm1\text{ }\mu\text{m} as 10−3 m10^{-3}\text{ m} when converting the thickness tt, even though you correctly converted ΔL=68.0 μm\Delta L = 68.0\text{ }\mu\text{m} as 68.0×10−6 m68.0 \times 10^{-6}\text{ m} later on.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Inconsistent handling of the micro (μ\mu) prefix led to an erroneous substitution of 10−310^{-3} instead of 10−610^{-6} for the thickness, resulting in an area that was inflated by three orders of magnitude.

REASONING PATH
Your ACEpath teacher’s suggested approach
SI Prefix Multipliers
  • milli- (m)=10−3\text{milli- } (\text{m}) = 10^{-3}, while micro- (μ)=10−6\text{micro- } (\mu) = 10^{-6}.

  • Always verify that every parameter with the symbol μ\mu is multiplied by 10−610^{-6} when converting to base SI units.

Sanity Check on Material Modulus
  • Metals typically have Young's moduli on the order of tens to hundreds of gigapascals (1010 to 1011 Pa10^{10}\text{ to } 10^{11}\text{ Pa}).

  • If a metallic specimen yields E≈0.06 GPaE \approx 0.06\text{ GPa}, check your cross-sectional area for an accidental factor of 10310^3 or 10610^6.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Convert the wire thickness using the correct micro prefix: t=380 μm=3.80×10−4 mt = 380\text{ }\mu\text{m} = 3.80 \times 10^{-4}\text{ m}.

  2. Recalculate the cross-sectional area: A=(3.80×10−4 m)×(6.50×10−4 m)=2.47×10−7 m2A = (3.80 \times 10^{-4}\text{ m}) \times (6.50 \times 10^{-4}\text{ m}) = 2.47 \times 10^{-7}\text{ m}^2.

  3. Recalculate the tensile stress: σ=42.5 N2.47×10−7 m2≈1.7206×108 Pa=172 MPa\sigma = \frac{42.5\text{ N}}{2.47 \times 10^{-7}\text{ m}^2} \approx 1.7206 \times 10^8\text{ Pa} = 172\text{ MPa}.

  4. Recalculate Young's modulus: E=1.7206×108 Pa2.72×10−3≈6.33×1010 Pa=63.3 GPaE = \frac{1.7206 \times 10^8\text{ Pa}}{2.72 \times 10^{-3}} \approx 6.33 \times 10^{10}\text{ Pa} = 63.3\text{ GPa}.

Final answer

(a) σ=172 MPa\sigma = 172\text{ MPa}; (b) ε=2.72×10−3=2720 με\varepsilon = 2.72 \times 10^{-3} = 2720\text{ }\mu\varepsilon; (c) E=63.3 GPaE = 63.3\text{ GPa}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the standard metric prefix table from nano (10−910^{-9}) to giga (10910^9) to build instant recognition.

  • Practice writing units explicitly in scientific notation during conversion steps before multiplying them to find areas or volumes.

  • Perform order-of-magnitude checks on intermediate geometric dimensions (e.g., verifying that a 380 μm380\text{ }\mu\text{m} wire cannot be 0.38 m=38 cm0.38\text{ m} = 38\text{ cm} thick).

OverviewACEpath Teacher's Diagnosis

02 The student computes tensile strain using the deformed final length in the denominator rather than the original gauge length, leading to an incorrect strain and subsequent Young's modulus.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    t=3.80×10−4 mt = 3.80 \times 10^{-4}\text{ m}, w=6.50×10−4 mw = 6.50 \times 10^{-4}\text{ m}, L0=2.50×10−2 mL_0 = 2.50 \times 10^{-2}\text{ m}, ΔL=6.80×10−5 m  ⟹  A=(3.80×10−4 m)×(6.50×10−4 m)=2.47×10−7 m2\Delta L = 6.80 \times 10^{-5}\text{ m} \implies A = (3.80 \times 10^{-4}\text{ m}) \times (6.50 \times 10^{-4}\text{ m}) = 2.47 \times 10^{-7}\text{ m}^2

  2. Step 2

    σ=FA=42.5 N2.47×10−7 m2=1.72×108 Pa=172 MPa\sigma = \frac{F}{A} = \frac{42.5\text{ N}}{2.47 \times 10^{-7}\text{ m}^2} = 1.72 \times 10^8\text{ Pa} = 172\text{ MPa}

  3. Step 3

    L=L0+ΔL=0.0250 m+0.000068 m=0.025068 m  ⟹  ε=ΔLL=6.80×10−5 m0.025068 m=0.002713  ⟹  ε=2713 μεL = L_0 + \Delta L = 0.0250\text{ m} + 0.000068\text{ m} = 0.025068\text{ m} \implies \varepsilon = \frac{\Delta L}{L} = \frac{6.80 \times 10^{-5}\text{ m}}{0.025068\text{ m}} = 0.002713 \implies \varepsilon = 2713\text{ }\mu\varepsilon

    Correct

    ε=ΔLL0=6.80×10−5 m2.50×10−2 m=2.72×10−3=2720 με\varepsilon = \frac{\Delta L}{L_0} = \frac{6.80 \times 10^{-5}\text{ m}}{2.50 \times 10^{-2}\text{ m}} = 2.72 \times 10^{-3} = 2720\text{ }\mu\varepsilon

    Engineering strain is defined relative to the undeformed initial gauge length L0L_0, not the deformed final length LL. Dividing by L0=0.0250 mL_0 = 0.0250\text{ m} gives ε=2.72×10−3=2720 με\varepsilon = 2.72 \times 10^{-3} = 2720\text{ }\mu\varepsilon.

  4. Step 4

    E=σε=1.7206×108 Pa0.002713=6.34×1010 Pa=63.4 GPaE = \frac{\sigma}{\varepsilon} = \frac{1.7206 \times 10^8\text{ Pa}}{0.002713} = 6.34 \times 10^{10}\text{ Pa} = 63.4\text{ GPa}

    Correct

    E=σε=1.7206×108 Pa2.72×10−3≈6.33×1010 Pa=63.3 GPaE = \frac{\sigma}{\varepsilon} = \frac{1.7206 \times 10^8\text{ Pa}}{2.72 \times 10^{-3}} \approx 6.33 \times 10^{10}\text{ Pa} = 63.3\text{ GPa}

    Your formula for Young's modulus E=σεE = \frac{\sigma}{\varepsilon} and your unit conversion to gigapascals are completely correct, but the numerical answer was affected by the slightly underestimated strain from Step 3.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly converted all dimensions from micrometers and millimeters into meters.

You calculated the cross-sectional area and normal tensile stress with correct units and precision.

You correctly identified Hooke's law relating Young's modulus to stress and strain.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Denominator confusion in engineering strain

You computed the final length L=L0+ΔLL = L_0 + \Delta L and placed LL in the denominator of the strain formula.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Conflating engineering strain (which compares change in length to the original undeformed length L0L_0) with true strain or fractional length relative to the instantaneous/final state.

REASONING PATH
Your ACEpath teacher’s suggested approach
Engineering Strain Definition
  • Engineering tensile strain ε\varepsilon is always defined as elongation divided by initial gauge length: ε=ΔLL0\varepsilon = \frac{\Delta L}{L_0}.

  • Never add ΔL\Delta L to L0L_0 to form the denominator for engineering strain; keep the original length L0L_0 fixed in the denominator.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Calculate engineering strain using the original gauge length: ε=ΔLL0=6.80×10−5 m2.50×10−2 m=2.72×10−3\varepsilon = \frac{\Delta L}{L_0} = \frac{6.80 \times 10^{-5}\text{ m}}{2.50 \times 10^{-2}\text{ m}} = 2.72 \times 10^{-3}

  2. Convert to microstrain: ε=2.72×10−3×106=2720 με\varepsilon = 2.72 \times 10^{-3} \times 10^6 = 2720\text{ }\mu\varepsilon

  3. Calculate Young's modulus: E=σε=1.7206×108 Pa2.72×10−3=6.326×1010 Pa≈63.3 GPaE = \frac{\sigma}{\varepsilon} = \frac{1.7206 \times 10^8\text{ Pa}}{2.72 \times 10^{-3}} = 6.326 \times 10^{10}\text{ Pa} \approx 63.3\text{ GPa}

Final answer

(a) σ=172 MPa\sigma = 172\text{ MPa}; (b) ε=2.72×10−3=2720 με\varepsilon = 2.72 \times 10^{-3} = 2720\text{ }\mu\varepsilon; (c) E=63.3 GPaE = 63.3\text{ GPa}

NEXT STEPS
Final Takeaways from Your Teacher
  • When calculating strain, verify whether engineering strain or true strain is requested; standard tensile test problems almost universally use engineering strain ΔLL0\frac{\Delta L}{L_0}.

  • Double-check that denominators in deformation formulas always refer to reference (undeformed) state quantities (A0A_0, L0L_0).

OverviewACEpath Teacher's Diagnosis

03 The student misapplies the metric prefix conversion between pascals and gigapascals by using 10⁶ instead of 10⁹, resulting in a Young's modulus that is off by a factor of 1000.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    t=3.80×10−4 mt = 3.80 \times 10^{-4}\text{ m}, w=6.50×10−4 mw = 6.50 \times 10^{-4}\text{ m}, L0=2.50×10−2 mL_0 = 2.50 \times 10^{-2}\text{ m}, ΔL=6.80×10−5 m  ⟹  A=(3.80×10−4 m)×(6.50×10−4 m)=2.47×10−7 m2\Delta L = 6.80 \times 10^{-5}\text{ m} \implies A = (3.80 \times 10^{-4}\text{ m}) \times (6.50 \times 10^{-4}\text{ m}) = 2.47 \times 10^{-7}\text{ m}^2

  2. Step 2

    σ=FA=42.5 N2.47×10−7 m2=1.72×108 Pa=172 MPa\sigma = \frac{F}{A} = \frac{42.5\text{ N}}{2.47 \times 10^{-7}\text{ m}^2} = 1.72 \times 10^8\text{ Pa} = 172\text{ MPa}

  3. Step 3

    ε=ΔLL0=68.0×10−6 m25.0×10−3 m=0.00272  ⟹  ε=2720 με\varepsilon = \frac{\Delta L}{L_0} = \frac{68.0 \times 10^{-6}\text{ m}}{25.0 \times 10^{-3}\text{ m}} = 0.00272 \implies \varepsilon = 2720\text{ }\mu\varepsilon

  4. Step 4

    E=σε=1.7206×108 Pa0.00272=6.33×1010 PaE = \frac{\sigma}{\varepsilon} = \frac{1.7206 \times 10^8\text{ Pa}}{0.00272} = 6.33 \times 10^{10}\text{ Pa}

  5. Step 5

    E=6.33×1010 Pa106=63300 GPaE = \frac{6.33 \times 10^{10}\text{ Pa}}{10^6} = 63300\text{ GPa}

    Correct

    E=6.33×1010 Pa109 Pa/GPa≈63.3 GPaE = \frac{6.33 \times 10^{10}\text{ Pa}}{10^9\text{ Pa/GPa}} \approx 63.3\text{ GPa}

    You used the conversion factor for mega (10610^6) rather than giga (10910^9). Since 1 GPa=109 Pa1\text{ GPa} = 10^9\text{ Pa}, dividing 6.33×1010 Pa6.33 \times 10^{10}\text{ Pa} by 109 Pa/GPa10^9\text{ Pa/GPa} yields 63.3 GPa63.3\text{ GPa}.

WHAT YOU DID WELL
Compliments from Your Teacher

You converted all micro- and millimeter dimensions into base SI units with correct powers of ten.

You calculated the cross-sectional area, tensile stress, and tensile strain with high numerical precision.

You correctly applied Hooke's law, E=σεE = \frac{\sigma}{\varepsilon}, in base units of pascals.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Metric prefix confusion (Mega vs. Giga)

You divided by 10610^6 instead of 10910^9 when converting pascals to gigapascals.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing the SI prefixes 'mega-' (10610^6) and 'giga-' (10910^9) during the final unit conversion of elastic moduli.

REASONING PATH
Your ACEpath teacher’s suggested approach
Recall SI Prefixes for Pressure and Stress
  • 1 MPa=106 Pa1\text{ MPa} = 10^6\text{ Pa} and 1 GPa=109 Pa=103 MPa1\text{ GPa} = 10^9\text{ Pa} = 10^3\text{ MPa}.

  • Always double-check that you divide by 10910^9 when converting from pascals (Pa\text{Pa}) to gigapascals (GPa\text{GPa}).

Sanity Check Material Moduli
  • Typical metal alloys have Young's moduli between 50 GPa50\text{ GPa} and 250 GPa250\text{ GPa}.

  • If your calculated modulus is tens of thousands of GPa\text{GPa}, check whether you accidentally used the mega- prefix conversion.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Apply the metric prefix conversion definition: 1 GPa=109 Pa1\text{ GPa} = 10^9\text{ Pa}.

  2. Convert by dividing by 109 Pa/GPa10^9\text{ Pa/GPa}: E=6.326×1010 Pa109 Pa/GPa≈63.3 GPaE = \frac{6.326 \times 10^{10}\text{ Pa}}{10^9\text{ Pa/GPa}} \approx 63.3\text{ GPa}.

Final answer

(a) σ=172 MPa\sigma = 172\text{ MPa}; (b) ε=2.72×10−3=2720 με\varepsilon = 2.72 \times 10^{-3} = 2720\text{ }\mu\varepsilon; (c) E=63.3 GPaE = 63.3\text{ GPa}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review standard SI multiplier prefixes: kilo- (10310^3), mega- (10610^6), giga- (10910^9), and tera- (101210^{12}).

  • Perform a physical plausibility check on elastic stiffness values to ensure they fall within standard engineering ranges (101–102 GPa10^1\text{--}10^2\text{ GPa} for most metals).

Lock it in

Similar question

01

A circular micro-wire has a diameter of d=120 μmd = 120\text{ }\mu\text{m} and is subjected to an axial tensile force of F=3.40 NF = 3.40\text{ N}. Calculate the tensile stress σ\sigma in megapascals (MPa\text{MPa}).

Answer

σ=301 MPa\sigma = 301\text{ MPa}. First, convert diameter: d=120×10−6 m=1.20×10−4 md = 120 \times 10^{-6}\text{ m} = 1.20 \times 10^{-4}\text{ m}. The cross-sectional area is A=πd24=π(1.20×10−4 m)24≈1.131×10−8 m2A = \frac{\pi d^2}{4} = \frac{\pi (1.20 \times 10^{-4}\text{ m})^2}{4} \approx 1.131 \times 10^{-8}\text{ m}^2. Then σ=FA=3.40 N1.131×10−8 m2≈3.006×108 Pa=301 MPa\sigma = \frac{F}{A} = \frac{3.40\text{ N}}{1.131 \times 10^{-8}\text{ m}^2} \approx 3.006 \times 10^8\text{ Pa} = 301\text{ MPa}.

02

An orthodontic strip with a cross section of width w=0.800 mmw = 0.800\text{ mm} and thickness t=150 μmt = 150\text{ }\mu\text{m} has an initial length of L0=40.0 mmL_0 = 40.0\text{ mm}. Under a load of F=18.0 NF = 18.0\text{ N}, it stretches by ΔL=30.0 μm\Delta L = 30.0\text{ }\mu\text{m}. Find: (a) the cross-sectional area AA in m2\text{m}^2, (b) the tensile strain ε\varepsilon in microstrain (με\mu\varepsilon), and (c) the Young's modulus EE in GPa\text{GPa}.

Answer

(a) A=1.20×10−7 m2A = 1.20 \times 10^{-7}\text{ m}^2; (b) ε=750 με\varepsilon = 750\text{ }\mu\varepsilon; (c) E=200 GPaE = 200\text{ GPa}. Key steps: (a) w=8.00×10−4 mw = 8.00 \times 10^{-4}\text{ m}, t=1.50×10−4 mt = 1.50 \times 10^{-4}\text{ m}, so A=w⋅t=1.20×10−7 m2A = w \cdot t = 1.20 \times 10^{-7}\text{ m}^2. (b) ε=ΔLL0=3.00×10−5 m4.00×10−2 m=7.50×10−4=750 με\varepsilon = \frac{\Delta L}{L_0} = \frac{3.00 \times 10^{-5}\text{ m}}{4.00 \times 10^{-2}\text{ m}} = 7.50 \times 10^{-4} = 750\text{ }\mu\varepsilon. (c) σ=FA=18.0 N1.20×10−7 m2=1.50×108 Pa=150 MPa\sigma = \frac{F}{A} = \frac{18.0\text{ N}}{1.20 \times 10^{-7}\text{ m}^2} = 1.50 \times 10^8\text{ Pa} = 150\text{ MPa}. Thus, E=σε=1.50×108 Pa7.50×10−4=2.00×1011 Pa=200 GPaE = \frac{\sigma}{\varepsilon} = \frac{1.50 \times 10^8\text{ Pa}}{7.50 \times 10^{-4}} = 2.00 \times 10^{11}\text{ Pa} = 200\text{ GPa}.

03

A titanium alloy tie-rod of length L0=1.50 mL_0 = 1.50\text{ m} and rectangular cross section (t=2.50 mmt = 2.50\text{ mm}, w=12.0 mmw = 12.0\text{ mm}) supports a tensile load of F=3.30 kNF = 3.30\text{ kN}. If the material's Young's modulus is E=110 GPaE = 110\text{ GPa}, determine the elongation ΔL\Delta L in micrometers (μm\mu\text{m}).

Answer

ΔL=1500 μm\Delta L = 1500\text{ }\mu\text{m} (1.50 mm1.50\text{ mm}). Key steps: Cross-sectional area A=(2.50×10−3 m)×(12.0×10−3 m)=3.00×10−5 m2A = (2.50 \times 10^{-3}\text{ m}) \times (12.0 \times 10^{-3}\text{ m}) = 3.00 \times 10^{-5}\text{ m}^2. Tensile stress σ=FA=3300 N3.00×10−5 m2=1.10×108 Pa=110 MPa\sigma = \frac{F}{A} = \frac{3300\text{ N}}{3.00 \times 10^{-5}\text{ m}^2} = 1.10 \times 10^8\text{ Pa} = 110\text{ MPa}. Tensile strain ε=σE=1.10×108 Pa1.10×1011 Pa=1.00×10−3\varepsilon = \frac{\sigma}{E} = \frac{1.10 \times 10^8\text{ Pa}}{1.10 \times 10^{11}\text{ Pa}} = 1.00 \times 10^{-3}. Elongation ΔL=ε⋅L0=1.00×10−3×1.50 m=1.50×10−3 m=1500 μm\Delta L = \varepsilon \cdot L_0 = 1.00 \times 10^{-3} \times 1.50\text{ m} = 1.50 \times 10^{-3}\text{ m} = 1500\text{ }\mu\text{m}.

Loading workspace…