Resources

A mechanic uses a straight wrench of length r=0.320 mr = 0.320\text{ m} to tighten a bolt located at the pivot. She pulls at the outer tip of the wrench with a force of F=85.0 NF = 85.0\text{ N}. If the bolt requires a torque of magnitude τ=18.5 N⋅m\tau = 18.5\text{ N}\cdot\text{m} to begin turning, determine the acute angle θ\theta (in degrees) that the applied force vector must make with the longitudinal axis of the wrench.

Answer and steps

Final answer

θ=42.9∘\theta = 42.9^\circ

Steps

01

Identify the Torque Formula

The magnitude of torque τ\tau generated by a force F⃗\vec{F} applied at a displacement vector r⃗\vec{r} from a pivot point is given by:

τ=rFsin⁡θ\tau = r F \sin\theta

where:

  • rr is the length of the wrench (distance from the bolt pivot to the point of force application),
  • FF is the magnitude of the applied force,
  • θ\theta is the angle between the longitudinal axis of the wrench (the line of r⃗\vec{r}) and the applied force vector F⃗\vec{F}.

Only the component of force perpendicular to the wrench, F⊥=Fsin⁡θF_\perp = F \sin\theta, produces a torque about the pivot.


02

Solve for the Angle θ\theta

Rearrange the torque equation to solve for sin⁡θ\sin\theta:

sin⁡θ=τrF\sin\theta = \frac{\tau}{r F}

Substitute the given values:

  • r=0.320 mr = 0.320\text{ m}
  • F=85.0 NF = 85.0\text{ N}
  • τ=18.5 N⋅m\tau = 18.5\text{ N}\cdot\text{m}

sin⁡θ=18.5 N⋅m(0.320 m)(85.0 N)=18.527.2≈0.68015\sin\theta = \frac{18.5\text{ N}\cdot\text{m}}{(0.320\text{ m})(85.0\text{ N})} = \frac{18.5}{27.2} \approx 0.68015


03

Calculate the Value of θ\theta

Take the inverse sine to find the acute angle:

θ=arcsin⁡(0.68015)≈42.9∘\theta = \arcsin(0.68015) \approx 42.9^\circ

Pitfall to Avoid: Always verify how the angle is defined. If the angle were measured relative to a line perpendicular to the wrench, the torque would be expressed using cos⁡θ\cos\theta. Since θ\theta is explicitly measured from the longitudinal axis along the wrench, the effective perpendicular lever component uses sin⁡θ\sin\theta.

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student misremembers the torque formula by using cosine instead of sine to resolve the perpendicular component of force along the wrench axis.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    τ=r∗F∗cos⁡(θ)  ⟹  18.5=0.320∗85.0∗cos⁡(θ)\tau = r * F * \cos(\theta) \implies 18.5 = 0.320 * 85.0 * \cos(\theta)

    Correct

    τ=rFsin⁡θ  ⟹  18.5=(0.320)(85.0)sin⁡θ\tau = r F \sin\theta \implies 18.5 = (0.320)(85.0)\sin\theta

    You set up the relationship and substituted the numerical values, but torque depends on the perpendicular component of the force relative to the lever arm: τ=rFsin⁡θ\tau = r F \sin\theta. When θ\theta is measured from the wrench's longitudinal axis, the perpendicular component is Fsin⁡θF\sin\theta, not Fcos⁡θF\cos\theta.

  2. Step 2

    cos⁡(θ)=18.527.2≈0.6801\cos(\theta) = \frac{18.5}{27.2} \approx 0.6801

    Correct

    sin⁡θ=18.527.2≈0.68015\sin\theta = \frac{18.5}{27.2} \approx 0.68015

    You carried out the arithmetic and isolated the trigonometric ratio accurately based on your expression in Step 1.

  3. Step 3

    θ=arccos⁡(0.6801)≈47.1∘\theta = \arccos(0.6801) \approx 47.1^\circ

    Correct

    θ=arcsin⁡(0.68015)≈42.9∘\theta = \arcsin(0.68015) \approx 42.9^\circ

    You correctly took the inverse trigonometric function of your computed value, but evaluating the arcsine of 0.680150.68015 yields θ≈42.9∘\theta \approx 42.9^\circ.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly substituted the given values for torque, force, and wrench length.

You accurately carried out the algebraic isolation of the trigonometric term.

You properly evaluated the inverse trigonometric function in degrees.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Incorrect Trigonometric Component in Torque

Selecting cosine instead of sine when resolving the torque perpendicular to the lever arm.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You associated resolving a vector with cos⁡θ\cos\theta by default, overlooking that the angle θ\theta is measured relative to the line of the lever arm, making the perpendicular (torque-producing) component opposite to θ\theta (F⊥=Fsin⁡θF_\perp = F\sin\theta).

REASONING PATH
Your ACEpath teacher’s suggested approach
Identify the Torque-Producing Component
  • Only the component of force perpendicular to the position vector r⃗\vec{r} creates torque: τ=rF⊥=rFsin⁡θ\tau = r F_\perp = r F \sin\theta, where θ\theta is the angle between r⃗\vec{r} and F⃗\vec{F}.

  • Always draw a small right triangle at the force vector to confirm whether the perpendicular component is opposite (sin⁡θ\sin\theta) or adjacent (cos⁡θ\cos\theta) to the given angle.

Check Extreme Angle Values
  • If pulling directly along the wrench axis (θ=0∘\theta = 0^\circ), torque must be zero because the line of action passes through the pivot.

  • Test θ=0∘\theta = 0^\circ: sin⁡(0∘)=0\sin(0^\circ) = 0 gives zero torque, whereas cos⁡(0∘)=1\cos(0^\circ) = 1 would erroneously predict maximum torque.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Apply the standard torque definition: τ=rFsin⁡θ\tau = r F \sin\theta.

  2. Substitute the given quantities: 18.5=(0.320)(85.0)sin⁡θ=27.2sin⁡θ18.5 = (0.320)(85.0)\sin\theta = 27.2\sin\theta.

  3. Isolate sin⁡θ\sin\theta: sin⁡θ=18.527.2≈0.68015\sin\theta = \frac{18.5}{27.2} \approx 0.68015.

  4. Compute the acute angle: θ=arcsin⁡(0.68015)≈42.9∘\theta = \arcsin(0.68015) \approx 42.9^\circ.

Final answer

θ=42.9∘\theta = 42.9^\circ

NEXT STEPS
Final Takeaways from Your Teacher
  • Review vector cross products to reinforce why τ⃗=r⃗×F⃗\vec{\tau} = \vec{r} \times \vec{F} naturally uses the sine of the included angle.

  • Practice checking physical limits (such as θ=0∘\theta = 0^\circ and θ=90∘\theta = 90^\circ) before finalizing formulas.

  • Complete the follow-up drills to solidify when to use sine versus cosine depending on how the reference angle is defined.

OverviewACEpath Teacher's Diagnosis

02 The student calculates the angle in radians using an inverse trigonometric function but fails to convert the final result to degrees as requested.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    sin⁡(θ)=τr∗F\sin(\theta) = \frac{\tau}{r * F}

  2. Step 2

    sin⁡(θ)=18.50.320∗85.0=0.6801\sin(\theta) = \frac{18.5}{0.320 * 85.0} = 0.6801

  3. Step 3

    θ=arcsin⁡(0.6801)=0.748 rad\theta = \arcsin(0.6801) = 0.748\text{ rad}

    Correct

    θ=arcsin⁡(0.68015)≈42.9∘\theta = \arcsin(0.68015) \approx 42.9^\circ

    Your numeric inverse sine value in radians is correct, but the prompt specifically requested the acute angle in degrees.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified and applied the torque magnitude relation τ=rFsin⁡θ\tau = r F \sin\theta.

You correctly isolated the trigonometric ratio and accurately evaluated arcsin⁡(0.6801)\arcsin(0.6801).

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Angle unit omission (radians instead of degrees)

You evaluated arcsin⁡(0.6801)\arcsin(0.6801) while your calculator was in radian mode (or wrote the result in radians) without converting it to degrees.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Overlooking unit specifications in the prompt and omitting a final conversion factor (×180∘π\times \frac{180^\circ}{\pi}) when calculating angles from inverse trigonometric functions.

REASONING PATH
Your ACEpath teacher’s suggested approach
Verify Required Angle Units
  • Always inspect the problem statement for unit specifications: whether the requested angle is in degrees (∘^\circ) or radians (rad\text{rad}).

  • Check your calculator's angle mode (DEG vs. RAD) before pressing sin⁡−1\sin^{-1}, or multiply a radian result by 180∘π\frac{180^\circ}{\pi}.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. θ=arcsin⁡(0.68015)≈0.7480 rad\theta = \arcsin(0.68015) \approx 0.7480\text{ rad}

  2. θ=0.7480 rad×180∘π≈42.9∘\theta = 0.7480\text{ rad} \times \frac{180^\circ}{\pi} \approx 42.9^\circ

Final answer

θ=42.9∘\theta = 42.9^\circ

NEXT STEPS
Final Takeaways from Your Teacher
  • Always highlight or underline the requested final units in the problem prompt before beginning calculations.

  • Ensure your scientific calculator is set to degree mode whenever a physics problem asks for an angle in degrees.

OverviewACEpath Teacher's Diagnosis

03 The student sets up the ratio upside down when solving for sin(θ), dividing the product of force and radius by torque instead of dividing torque by the product.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    τ=r∗F∗sin⁡(θ)\tau = r * F * \sin(\theta)

  2. Step 2

    sin⁡(θ)=r∗Fτ\sin(\theta) = \frac{r * F}{\tau}

    Correct

    sin⁡θ=τrF\sin\theta = \frac{\tau}{r F}

    When dividing both sides of τ=rFsin⁡θ\tau = r F \sin\theta by the factor rFr F, the product rFr F must be in the denominator, not the numerator.

  3. Step 3

    sin⁡(θ)=0.320∗85.018.5=27.218.5≈1.47\sin(\theta) = \frac{0.320 * 85.0}{18.5} = \frac{27.2}{18.5} \approx 1.47

    Correct

    sin⁡θ=18.50.320×85.0=18.527.2≈0.680\sin\theta = \frac{18.5}{0.320 \times 85.0} = \frac{18.5}{27.2} \approx 0.680

    Your arithmetic evaluation was performed correctly on the inverted ratio, which propagated the earlier algebraic error.

  4. Step 4

    θ cannot be found because sin⁡(θ)>1\theta\text{ cannot be found because }\sin(\theta) > 1

    Correct

    θ=arcsin⁡(0.68015)≈42.9∘\theta = \arcsin(0.68015) \approx 42.9^\circ

    Although you correctly noted that the sine of a real angle cannot exceed 11, this conclusion stemmed directly from the inverted fraction in your rearrangement.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified and applied the fundamental torque equation τ=rFsin⁡θ\tau = r F \sin\theta.

You demonstrated strong mathematical awareness by recognizing that a sine value greater than 11 is invalid for real angles.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Algebraic isolation error (inverted ratio)

You inverted the fraction when solving for sin⁡θ\sin\theta, placing rFr F in the numerator and τ\tau in the denominator.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Misidentifying which term acts as the divisor when dividing both sides of an equation of the form A=B⋅CA = B \cdot C to isolate CC.

REASONING PATH
Your ACEpath teacher’s suggested approach
Isolating Factors in a Product
  • To solve A=B⋅CA = B \cdot C for CC, divide both sides by BB, yielding C=ABC = \frac{A}{B}.

  • Divide both sides of τ=(rF)sin⁡θ\tau = (r F)\sin\theta by (rF)(r F) so that sin⁡θ=τrF\sin\theta = \frac{\tau}{r F}.

Magnitude Sanity Check
  • The maximum possible torque is τmax⁡=rF\tau_{\max} = r F, which occurs when θ=90∘\theta = 90^\circ.

  • Compare the required torque τ\tau to rFr F; since τ≤τmax⁡\tau \le \tau_{\max}, the ratio τrF\frac{\tau}{r F} must always be less than or equal to 11.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. sin⁡θ=τrF\sin\theta = \frac{\tau}{r F}

  2. sin⁡θ=18.5 N⋅m(0.320 m)(85.0 N)=18.527.2≈0.68015\sin\theta = \frac{18.5\text{ N}\cdot\text{m}}{(0.320\text{ m})(85.0\text{ N})} = \frac{18.5}{27.2} \approx 0.68015

  3. θ=arcsin⁡(0.68015)≈42.9∘\theta = \arcsin(0.68015) \approx 42.9^\circ

Final answer

θ≈42.9∘\theta \approx 42.9^\circ

NEXT STEPS
Final Takeaways from Your Teacher
  • Review one-step algebraic division when solving for a factor in a product.

  • Use the physical boundary condition τ≤rF\tau \le r F to verify that your isolated expression for sin⁡θ\sin\theta never exceeds 11.

Lock it in

Similar question

01

A technician applies a force of 120 N120\text{ N} to a 0.250 m0.250\text{ m} long wrench. If the applied force makes an angle of 60.0∘60.0^\circ with the handle of the wrench, what torque is exerted on the bolt?

Answer

τ=26.0 N⋅m\tau = 26.0\text{ N}\cdot\text{m}. Key steps:

  1. τ=rFsin⁡θ\tau = r F \sin\theta
  2. τ=(0.250 m)(120 N)sin⁡(60.0∘)\tau = (0.250\text{ m})(120\text{ N})\sin(60.0^\circ)
  3. τ=30.0×32≈25.98 N⋅m≈26.0 N⋅m\tau = 30.0 \times \frac{\sqrt{3}}{2} \approx 25.98\text{ N}\cdot\text{m} \approx 26.0\text{ N}\cdot\text{m}.
02

A door of width w=0.900 mw = 0.900\text{ m} requires a torque of 15.0 N⋅m15.0\text{ N}\cdot\text{m} about its hinges to open. A person pushes on the edge opposite the hinges with a force of 22.0 N22.0\text{ N}. Find the acute angle θ\theta between the force vector and the face of the door.

Answer

θ=49.3∘\theta = 49.3^\circ. Key steps:

  1. τ=wFsin⁡θ  ⟹  sin⁡θ=τwF\tau = w F \sin\theta \implies \sin\theta = \frac{\tau}{w F}
  2. sin⁡θ=15.0 N⋅m(0.900 m)(22.0 N)=15.019.8≈0.7576\sin\theta = \frac{15.0\text{ N}\cdot\text{m}}{(0.900\text{ m})(22.0\text{ N})} = \frac{15.0}{19.8} \approx 0.7576
  3. θ=arcsin⁡(0.7576)≈49.3∘\theta = \arcsin(0.7576) \approx 49.3^\circ.
03

A uniform beam pivoted at one end is pulled by a cable attached to its far end. The cable tension is T=350 NT = 350\text{ N} directed at an angle ϕ=25.0∘\phi = 25.0^\circ to the normal (perpendicular) of the beam. If the beam is 2.40 m2.40\text{ m} long, calculate the torque produced about the pivot.

Answer

τ=761 N⋅m\tau = 761\text{ N}\cdot\text{m}. Key steps:

  1. Identify the perpendicular force component: because ϕ\phi is measured from the normal to the beam, the component perpendicular to the beam is F⊥=Tcos⁡ϕF_\perp = T \cos\phi.
  2. τ=r(Tcos⁡ϕ)=(2.40 m)(350 N)cos⁡(25.0∘)\tau = r (T \cos\phi) = (2.40\text{ m})(350\text{ N})\cos(25.0^\circ)
  3. τ=840×0.9063≈761 N⋅m\tau = 840 \times 0.9063 \approx 761\text{ N}\cdot\text{m}.
Loading workspace…