Resources

A Pitot-static tube is aligned parallel to the uniform airflow over a scaled aerodynamic model in an atmospheric wind tunnel where the ambient air density is ρair=1.20 kg/m3\rho_{\text{air}} = 1.20\text{ kg/m}^3. The stagnation (impact) port at the nose of the probe detects total pressure P0P_0, while the flush circumferential side holes measure ambient static pressure PsP_s. The pressure difference is coupled to a vertical U-tube manometer filled with dyed water of density ρwater=1000 kg/m3\rho_{\text{water}} = 1000\text{ kg/m}^3. If the observed vertical column height difference in the manometer is h=3.60 cmh = 3.60\text{ cm}, determine the flow velocity vv of the oncoming airstream. (Use g=9.80 m/s2g = 9.80\text{ m/s}^2.)

Answer and steps

Final answer

v=24.2 m/sv = 24.2\text{ m/s}

Steps

1. Apply Bernoulli's Principle to the Airflow

Consider a streamline in the undisturbed oncoming airflow traveling at speed vv with static pressure PsP_s and air density ρair\rho_{\text{air}}.

When the air encounters the front opening (impact port) of the Pitot tube, it is brought to rest adiabatically and isentropically at a stagnation point where the velocity is zero and the pressure rises to the total (stagnation) pressure P0P_0.

Applying Bernoulli's equation along this horizontal streamline:

Ps+12ρairv2=P0P_s + \frac{1}{2}\rho_{\text{air}}v^2 = P_0

The difference between the total pressure and the static pressure is the dynamic pressure:

P0−Ps=12ρairv2P_0 - P_s = \frac{1}{2}\rho_{\text{air}}v^2


2. Relate the Pressure Difference to the Manometer Reading

The impact port measures P0P_0 and the side circumferential ports measure the undisturbed static pressure PsP_s. These two ports are connected to opposite legs of the U-tube manometer.

The hydrostatic pressure difference balanced by the liquid column of height hh in the manometer is given by:

P0−Ps=ρwaterghP_0 - P_s = \rho_{\text{water}} g h

(Note: Because ρair≪ρwater\rho_{\text{air}} \ll \rho_{\text{water}}, the hydrostatic column of air inside the manometer lines is negligible.)


3. Solve for the Flow Velocity vv

Equating the dynamic pressure of the airflow to the hydrostatic pressure head of the manometer:

12ρairv2=ρwatergh\frac{1}{2}\rho_{\text{air}}v^2 = \rho_{\text{water}} g h

Rearranging for the flow velocity vv:

v=2ρwaterghρairv = \sqrt{\frac{2\rho_{\text{water}} g h}{\rho_{\text{air}}}}


4. Substitute the Numerical Values

Convert the manometer column height to standard SI units: h=3.60 cm=0.0360 mh = 3.60\text{ cm} = 0.0360\text{ m}

Substitute the given values into the expression:

v=2⋅(1000 kg/m3)⋅(9.80 m/s2)⋅(0.0360 m)1.20 kg/m3v = \sqrt{\frac{2 \cdot (1000\text{ kg/m}^3) \cdot (9.80\text{ m/s}^2) \cdot (0.0360\text{ m})}{1.20\text{ kg/m}^3}}

v=705.61.20=588≈24.2 m/sv = \sqrt{\frac{705.6}{1.20}} = \sqrt{588} \approx 24.2\text{ m/s}


Common Pitfall to Avoid

  • Density Confusion: Always ensure the dynamic pressure term 12ρv2\frac{1}{2}\rho v^2 uses the density of the flowing fluid (ρair\rho_{\text{air}}), while the hydrostatic head ρgh\rho g h uses the density of the manometer fluid (ρwater\rho_{\text{water}}). Inverting these densities is a frequent source of error.

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student uses the air density instead of the manometer fluid (water) density in the hydrostatic equation ΔP = ρ g h, resulting in an incorrectly small pressure difference and a velocity of 0.840 m/s.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    P0−Ps=12ρairv2P_0 - P_s = \frac{1}{2}\rho_{\text{air}}v^2

  2. Step 2

    ΔP=ρairgh\Delta P = \rho_{\text{air}} g h

    Correct

    ΔP=ρwatergh\Delta P = \rho_{\text{water}} g h

    The height column hh is supported by the liquid inside the manometer (dyed water), so the hydrostatic equation must use ρwater=1000 kg/m3\rho_{\text{water}} = 1000\text{ kg/m}^3, not ρair\rho_{\text{air}}.

  3. Step 3

    12ρairv2=ρairgh  ⟹  v2=2gh=2⋅9.80⋅0.0360=0.7056  ⟹  v=0.7056=0.840 m/s\frac{1}{2}\rho_{\text{air}}v^2 = \rho_{\text{air}}gh \implies v^2 = 2gh = 2 \cdot 9.80 \cdot 0.0360 = 0.7056 \implies v = \sqrt{0.7056} = 0.840\text{ m/s}

    Correct

    12ρairv2=ρwatergh  ⟹  v=2ρwaterghρair≈24.2 m/s\frac{1}{2}\rho_{\text{air}}v^2 = \rho_{\text{water}}gh \implies v = \sqrt{\frac{2\rho_{\text{water}}gh}{\rho_{\text{air}}}} \approx 24.2\text{ m/s}

    Canceling ρair\rho_{\text{air}} followed from the incorrect density in the previous step, which led to an underestimated speed.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly related the difference between stagnation and static pressure to the kinetic energy per unit volume of the oncoming airstream using Bernoulli's equation.

You correctly converted the manometer height to meters and executed your algebraic steps accurately.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Fluid Density Confusion

Using ρair\rho_{\text{air}} instead of ρwater\rho_{\text{water}} in ΔP=ρgh\Delta P = \rho g h.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Conflating the flowing fluid that generates dynamic pressure with the manometer fluid that balances the pressure difference via hydrostatic equilibrium.

REASONING PATH
Your ACEpath teacher’s suggested approach
Identify Fluid Roles
  • Dynamic pressure 12ρv2\frac{1}{2}\rho v^2 belongs to the moving fluid; hydrostatic column difference ρgh\rho g h belongs to the liquid inside the U-tube manometer.

  • Label the two densities distinctly as ρflow\rho_{\text{flow}} and ρgage\rho_{\text{gage}} before writing equations to avoid canceling them out.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Express the hydrostatic pressure difference balanced by the water column: ΔP=ρwatergh\Delta P = \rho_{\text{water}} g h.

  2. Equate the dynamic pressure to the manometer pressure head: 12ρairv2=ρwatergh\frac{1}{2}\rho_{\text{air}}v^2 = \rho_{\text{water}}gh.

  3. Solve symbolically for velocity: v=2ρwaterghρairv = \sqrt{\frac{2\rho_{\text{water}}gh}{\rho_{\text{air}}}}.

  4. Substitute values: v=2⋅(1000 kg/m3)⋅(9.80 m/s2)⋅(0.0360 m)1.20 kg/m3=588≈24.2 m/sv = \sqrt{\frac{2 \cdot (1000\text{ kg/m}^3) \cdot (9.80\text{ m/s}^2) \cdot (0.0360\text{ m})}{1.20\text{ kg/m}^3}} = \sqrt{588} \approx 24.2\text{ m/s}.

Final answer

v≈24.2 m/sv \approx 24.2\text{ m/s}

NEXT STEPS
Final Takeaways from Your Teacher
  • Always write distinct descriptive subscripts for densities (e.g., ρair\rho_{\text{air}} and ρwater\rho_{\text{water}}) rather than a generic ρ\rho.

  • Perform a physical reality check on the answer: 0.84 m/s0.84\text{ m/s} is a gentle walking pace, which is unusually slow for an aerodynamic wind tunnel testing model airflow.

OverviewACEpath Teacher's Diagnosis

02 The student forgets to convert the manometer fluid column height from centimeters to meters, substituting h = 3.60 and obtaining an answer of 242 m/s that is too large by a factor of 10.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    P0−Ps=12ρairv2  ⟹  P0−Ps=ρwatergh  ⟹  12ρairv2=ρwaterghP_0 - P_s = \frac{1}{2}\rho_{\text{air}} v^2 \implies P_0 - P_s = \rho_{\text{water}} g h \implies \frac{1}{2}\rho_{\text{air}} v^2 = \rho_{\text{water}} g h

  2. Step 2

    v=2ρwaterghρairv = \sqrt{\frac{2\rho_{\text{water}} g h}{\rho_{\text{air}}}}

  3. Step 3

    v=2⋅1000⋅9.80⋅3.601.20=58800=242 m/sv = \sqrt{\frac{2 \cdot 1000 \cdot 9.80 \cdot 3.60}{1.20}} = \sqrt{58800} = 242\text{ m/s}

    Correct

    v=2⋅1000⋅9.80⋅0.03601.20=588≈24.2 m/sv = \sqrt{\frac{2 \cdot 1000 \cdot 9.80 \cdot 0.0360}{1.20}} = \sqrt{588} \approx 24.2\text{ m/s}

    You substituted h=3.60 cmh = 3.60\text{ cm} directly without converting it to meters (0.0360 m0.0360\text{ m}). Because the other quantities use SI base units, leaving hh in centimeters made the value inside the radical 100100 times too large, resulting in a speed 1010 times higher than the true value.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly matched the dynamic pressure from Bernoulli's principle with the hydrostatic pressure head of the manometer.

You isolated the flow velocity vv symbolically with flawless algebraic steps.

You correctly assigned the densities to their corresponding fluids without mixing up air and water.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Unit conversion omission (cm to m)

You forgot to convert the manometer column height h=3.60 cmh = 3.60\text{ cm} into meters before computing the numerical value.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Overlooking unit consistency across SI base units during the final numerical evaluation.

REASONING PATH
Your ACEpath teacher’s suggested approach
Check SI base units before numerical substitution
  • Equations combining derived SI units (such as Pa\text{Pa}, kg/m3\text{kg/m}^3, and m/s2\text{m/s}^2) require all length parameters to be expressed in meters (m\text{m}).

  • Write down each given value with its unit converted to base SI units (e.g., h=3.60 cm=0.0360 mh = 3.60\text{ cm} = 0.0360\text{ m}) before plugging numbers into the formula.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Convert the manometer column height to meters: h=3.60 cm=0.0360 mh = 3.60\text{ cm} = 0.0360\text{ m}.

  2. Substitute SI values into the derived formula: v=2⋅(1000 kg/m3)⋅(9.80 m/s2)⋅(0.0360 m)1.20 kg/m3v = \sqrt{\frac{2 \cdot (1000\text{ kg/m}^3) \cdot (9.80\text{ m/s}^2) \cdot (0.0360\text{ m})}{1.20\text{ kg/m}^3}}.

  3. Evaluate the radicand: v=705.61.20=588v = \sqrt{\frac{705.6}{1.20}} = \sqrt{588}.

  4. Calculate the square root: v≈24.2 m/sv \approx 24.2\text{ m/s}.

Final answer

v≈24.2 m/sv \approx 24.2\text{ m/s}

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice converting non-standard units (such as cm\text{cm}, mm\text{mm}, or g/cm3\text{g/cm}^3) to base SI units in a dedicated preliminary step before entering numbers into your calculator.

  • Perform a sanity check on the magnitude of the final result: a wind tunnel speed of 242 m/s242\text{ m/s} is roughly Mach 0.70.7, which is unrealistically high for a mere 3.6 cm3.6\text{ cm} water column.

OverviewACEpath Teacher's Diagnosis

03 The student forgets to take the square root when solving for the flow velocity from kinetic dynamic pressure, writing v = 2 ρ_water g h / ρ_air = 588 m/s.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    P0−Ps=12ρairv2  ⟹  ΔP=ρwatergh=1000⋅9.80⋅0.0360=352.8 PaP_0 - P_s = \frac{1}{2}\rho_{\text{air}}v^2 \implies \Delta P = \rho_{\text{water}}gh = 1000 \cdot 9.80 \cdot 0.0360 = 352.8\text{ Pa}

  2. Step 2

    12⋅1.20⋅v=352.8  ⟹  v=2⋅352.81.20\frac{1}{2} \cdot 1.20 \cdot v = 352.8 \implies v = \frac{2 \cdot 352.8}{1.20}

    Correct

    12⋅1.20⋅v2=352.8  ⟹  v2=2⋅352.81.20=588\frac{1}{2} \cdot 1.20 \cdot v^2 = 352.8 \implies v^2 = \frac{2 \cdot 352.8}{1.20} = 588

    You omitted the square on vv when substituting the values into the dynamic pressure formula 12ρairv2\frac{1}{2}\rho_{\text{air}}v^2, writing vv instead of v2v^2.

  3. Step 3

    v=588 m/sv = 588\text{ m/s}

    Correct

    v=588≈24.2 m/sv = \sqrt{588} \approx 24.2\text{ m/s}

    Because the velocity term was not squared in the previous step, your final result represents v2v^2 rather than vv.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified that the total and static pressure difference equals the dynamic pressure of the oncoming airstream.

You correctly matched the densities to their proper fluids, using ρwater\rho_{\text{water}} for the manometer column and ρair\rho_{\text{air}} for the airflow.

You correctly converted the column height from centimeters to meters before evaluating the hydrostatic pressure.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Omitted Exponent in Formula

Dropping the exponent 22 on velocity when rewriting 12ρv2\frac{1}{2}\rho v^2 into numbers.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You lost track of the quadratic power v2v^2 in the kinetic energy / dynamic pressure term during algebraic substitution, leading to solving for vv linearly instead of taking the square root.

REASONING PATH
Your ACEpath teacher’s suggested approach
Dynamic Pressure Exponent Check
  • Dynamic pressure is quadratic in flow velocity: q=12ρv2q = \frac{1}{2}\rho v^2, so velocity must be obtained via a square root: v=2ΔPρv = \sqrt{\frac{2\Delta P}{\rho}}.

  • Always write the variable with its exponent v2v^2 when substituting numbers, and check that your final velocity expression includes a square root radical.

Dimensional / Magnitude Sanity Check
  • A speed of 588 m/s588\text{ m/s} is Mach 1.71.7 (supersonic), which is physically inconsistent with an atmospheric wind tunnel experiencing only 3.6 cm3.6\text{ cm} of water deflection.

  • Check whether the resulting velocity is reasonable for the given deflection before finalizing your answer.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Solve for v2v^2: v2=2⋅352.81.20=588 m2/s2v^2 = \frac{2 \cdot 352.8}{1.20} = 588\text{ m}^2/\text{s}^2

  2. Take the square root of both sides: v=588 m/s≈24.2 m/sv = \sqrt{588}\text{ m/s} \approx 24.2\text{ m/s}

Final answer

v≈24.2 m/sv \approx 24.2\text{ m/s}

NEXT STEPS
Final Takeaways from Your Teacher
  • Double-check that all squared variables in energy-like terms (such as 12mv2\frac{1}{2}mv^2 and 12ρv2\frac{1}{2}\rho v^2) retain their exponent after numerical substitution.

  • Perform a quick physical reality check on calculated speeds to catch missing roots (e.g., 588 m/s588\text{ m/s} vs. 24.2 m/s24.2\text{ m/s}).

Lock it in

Similar question

01

An airplane flies at an altitude where air density is ρair=0.90 kg/m3\rho_{\text{air}} = 0.90\text{ kg/m}^3. A differential pressure sensor connected to a Pitot-static probe registers ΔP=1620 Pa\Delta P = 1620\text{ Pa}. What is the true airspeed vv of the aircraft?

Answer

Using ΔP=12ρairv2\Delta P = \frac{1}{2}\rho_{\text{air}}v^2, we solve for speed: v=2ΔPρair=2⋅16200.90=3600=60 m/sv = \sqrt{\frac{2\Delta P}{\rho_{\text{air}}}} = \sqrt{\frac{2 \cdot 1620}{0.90}} = \sqrt{3600} = 60\text{ m/s}.

02

A Pitot-static tube in a wind tunnel (ρair=1.25 kg/m3\rho_{\text{air}} = 1.25\text{ kg/m}^3) is connected to an oil manometer (ρoil=800 kg/m3\rho_{\text{oil}} = 800\text{ kg/m}^3). If the measured column height difference is h=2.50 cmh = 2.50\text{ cm} and g=9.80 m/s2g = 9.80\text{ m/s}^2, find the airstream velocity vv.

Answer

First find the pressure difference: ΔP=ρoilgh=800⋅9.80⋅0.025=196 Pa\Delta P = \rho_{\text{oil}}gh = 800 \cdot 9.80 \cdot 0.025 = 196\text{ Pa}. Then equate to dynamic pressure: 12ρairv2=ΔP  ⟹  v=2⋅1961.25=313.6≈17.7 m/s\frac{1}{2}\rho_{\text{air}}v^2 = \Delta P \implies v = \sqrt{\frac{2 \cdot 196}{1.25}} = \sqrt{313.6} \approx 17.7\text{ m/s}.

03

Water (ρwater=1000 kg/m3\rho_{\text{water}} = 1000\text{ kg/m}^3) flows through a horizontal pipe. A Pitot-static tube inserted into the flow is connected to a mercury manometer (ρHg=13600 kg/m3\rho_{\text{Hg}} = 13600\text{ kg/m}^3). The height difference between the mercury columns is h=1.50 cmh = 1.50\text{ cm}. Calculate the flow speed vv of the water, accounting for the displaced water column in the manometer lines. (Use g=9.80 m/s2g = 9.80\text{ m/s}^2.)

Answer

Because the flowing fluid is also dense, the net hydrostatic pressure difference is ΔP=(ρHg−ρwater)gh=(13600−1000)(9.80)(0.0150)=12600⋅9.80⋅0.0150=1852.2 Pa\Delta P = (\rho_{\text{Hg}} - \rho_{\text{water}})gh = (13600 - 1000)(9.80)(0.0150) = 12600 \cdot 9.80 \cdot 0.0150 = 1852.2\text{ Pa}. Equating to the dynamic pressure of water: 12ρwaterv2=ΔP  ⟹  v=2⋅1852.21000=3.7044≈1.92 m/s\frac{1}{2}\rho_{\text{water}}v^2 = \Delta P \implies v = \sqrt{\frac{2 \cdot 1852.2}{1000}} = \sqrt{3.7044} \approx 1.92\text{ m/s}.

Loading workspace…