Resources

A cylindrical storage tank of radius R=1.20 mR = 1.20\text{ m} is filled with an industrial fluid of density ρ=1.15×103 kg/m3\rho = 1.15 \times 10^3\text{ kg/m}^3 open to the atmosphere where Patm=1.013×105 PaP_{\text{atm}} = 1.013 \times 10^5\text{ Pa}. Rather than calculating the resulting pressure at the bottom, determine the required liquid depth hh (in meters) such that the absolute pressure measured at the tank floor is exactly 1.450×105 Pa1.450 \times 10^5\text{ Pa}. Take g=9.80 m/s2g = 9.80\text{ m/s}^2.

Answer and steps

Final answer

h=3.88 mh = 3.88\text{ m}

Steps

01

Relate Absolute Pressure to Fluid Depth

Hydrostatic pressure in a fluid at rest depends on the depth below the surface, the density of the fluid, and the acceleration due to gravity. Because the tank is open to the atmosphere, the total (absolute) pressure PP at the bottom is the sum of the atmospheric pressure PatmP_{\text{atm}} acting on the surface and the hydrostatic pressure ρgh\rho g h exerted by the column of liquid:

P=Patm+ρghP = P_{\text{atm}} + \rho g h

Pitfall Note: The radius of the cylinder (R=1.20 mR = 1.20\text{ m}) is extra information. By Pascal's principle and the hydrostatic equation, pressure depends strictly on depth, not on the container's surface area or geometry.


02

Isolate the Required Depth hh

Subtract the atmospheric pressure from both sides to find the gauge pressure at the bottom, then solve for depth hh:

P−Patm=ρghP - P_{\text{atm}} = \rho g h

h=P−Patmρgh = \frac{P - P_{\text{atm}}}{\rho g}


03

Calculate the Numerical Value

Substitute the given parameters:

  • P=1.450×105 PaP = 1.450 \times 10^5\text{ Pa}
  • Patm=1.013×105 PaP_{\text{atm}} = 1.013 \times 10^5\text{ Pa}
  • ρ=1.15×103 kg/m3\rho = 1.15 \times 10^3\text{ kg/m}^3
  • g=9.80 m/s2g = 9.80\text{ m/s}^2

First, compute the gauge pressure:

P−Patm=1.450×105 Pa−1.013×105 Pa=0.437×105 Pa=43 700 PaP - P_{\text{atm}} = 1.450 \times 10^5\text{ Pa} - 1.013 \times 10^5\text{ Pa} = 0.437 \times 10^5\text{ Pa} = 43\,700\text{ Pa}

Next, calculate the denominator ρg\rho g:

ρg=(1.15×103 kg/m3)(9.80 m/s2)=11 270 N/m3\rho g = (1.15 \times 10^3\text{ kg/m}^3)(9.80\text{ m/s}^2) = 11\,270\text{ N/m}^3

Finally, divide to determine hh:

h=43 70011 270≈3.87755 mh = \frac{43\,700}{11\,270} \approx 3.87755\text{ m}

Rounding to three significant figures gives:

h=3.88 mh = 3.88\text{ m}

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student confuses absolute pressure with gauge pressure and equates total pressure directly to ρgh without subtracting atmospheric pressure, resulting in an overestimated depth.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    P=ρgh  ⟹  h=PρgP = \rho g h \implies h = \frac{P}{\rho g}

    Correct

    P=Patm+ρgh  ⟹  h=P−PatmρgP = P_{\text{atm}} + \rho g h \implies h = \frac{P - P_{\text{atm}}}{\rho g}

    Because the tank is open to the atmosphere, the absolute pressure at the bottom is the sum of atmospheric pressure and the fluid column pressure: P=Patm+ρghP = P_{\text{atm}} + \rho g h. Equating the absolute pressure directly to ρgh\rho g h treats the given total pressure as gauge pressure.

  2. Step 2

    h=1.450×1051.15×103×9.80  ⟹  h=14500011270h = \frac{1.450 \times 10^5}{1.15 \times 10^3 \times 9.80} \implies h = \frac{145000}{11270}

    Correct

    h=1.450×105−1.013×105(1.15×103)(9.80)=4370011270h = \frac{1.450 \times 10^5 - 1.013 \times 10^5}{(1.15 \times 10^3)(9.80)} = \frac{43700}{11270}

    Your numerical substitution and arithmetic are accurate according to your formula, but the numerator should be the net gauge pressure P−Patm=43 700 PaP - P_{\text{atm}} = 43\,700\text{ Pa} rather than the absolute pressure 145 000 Pa145\,000\text{ Pa}.

  3. Step 3

    h≈12.87 mh \approx 12.87\text{ m}

    Correct

    h≈3.88 mh \approx 3.88\text{ m}

    Due to the missing atmospheric pressure subtraction in Step 1, your final calculated depth is significantly overestimated.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly recognized that pressure in a static fluid depends on depth rather than the tank radius.

You manipulated your chosen algebraic formula cleanly to solve for hh.

You performed the numerical division accurately.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Omission of atmospheric pressure in absolute pressure calculation

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You conflated absolute pressure with gauge pressure. The expression ρgh\rho g h represents only the hydrostatic pressure contributed by the liquid column itself (the gauge pressure). When an open container is subjected to atmospheric pressure PatmP_{\text{atm}} at its free surface, that atmospheric pressure is transmitted uniformly throughout the fluid, making the total (absolute) pressure at depth hh equal to Patm+ρghP_{\text{atm}} + \rho g h.

REASONING PATH
Your ACEpath teacher’s suggested approach
Open Surface vs. Closed Vacuum
  • For any container open to the ambient air, total pressure equals Patm+ρghP_{\text{atm}} + \rho g h.

  • Always check whether the problem specifies an open container or gives PatmP_{\text{atm}}, and include PatmP_{\text{atm}} when working with absolute pressure.

Absolute vs. Gauge Pressure
  • Pgauge=Pabs−Patm=ρghP_{\text{gauge}} = P_{\text{abs}} - P_{\text{atm}} = \rho g h.

  • Before setting up ρgh\rho g h, ask yourself whether the target pressure is gauge pressure or absolute pressure.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Start with the complete absolute hydrostatic pressure formula: P=Patm+ρghP = P_{\text{atm}} + \rho g h.

  2. Isolate the fluid depth hh: h=P−Patmρgh = \frac{P - P_{\text{atm}}}{\rho g}.

  3. Substitute the given parameters: h=1.450×105 Pa−1.013×105 Pa(1.15×103 kg/m3)(9.80 m/s2)h = \frac{1.450 \times 10^5\text{ Pa} - 1.013 \times 10^5\text{ Pa}}{(1.15 \times 10^3\text{ kg/m}^3)(9.80\text{ m/s}^2)}.

  4. Evaluate the gauge pressure in the numerator: P−Patm=4.37×104 Pa=43 700 PaP - P_{\text{atm}} = 4.37 \times 10^4\text{ Pa} = 43\,700\text{ Pa}.

  5. Divide by ρg=11 270 N/m3\rho g = 11\,270\text{ N/m}^3: h=43 70011 270≈3.87755 mh = \frac{43\,700}{11\,270} \approx 3.87755\text{ m}.

Final answer

h=3.88 mh = 3.88\text{ m}

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice distinguishing between problems that ask for or provide absolute pressure versus gauge pressure.

  • Review the hydrostatic equation for open vessels to make sure PatmP_{\text{atm}} is included whenever total pressure is referenced.

OverviewACEpath Teacher's Diagnosis

02 The student adds atmospheric pressure instead of subtracting it when rearranging the hydrostatic equation for depth, leading to an incorrect pressure difference.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    P=Patm+ρghP = P_{\text{atm}} + \rho g h

  2. Step 2

    ρgh=P+Patm\rho g h = P + P_{\text{atm}}

    Correct

    ρgh=P−Patm\rho g h = P - P_{\text{atm}}

    To isolate the gauge pressure term ρgh\rho g h, you must subtract PatmP_{\text{atm}} from both sides of the equation, giving ρgh=P−Patm\rho g h = P - P_{\text{atm}}.

  3. Step 3

    h=1.450×105+1.013×1051.15×103×9.80  ⟹  h=24630011270≈21.85 mh = \frac{1.450 \times 10^5 + 1.013 \times 10^5}{1.15 \times 10^3 \times 9.80} \implies h = \frac{246300}{11270} \approx 21.85\text{ m}

    Correct

    h=1.450×105−1.013×1051.15×103×9.80=4370011270≈3.88 mh = \frac{1.450 \times 10^5 - 1.013 \times 10^5}{1.15 \times 10^3 \times 9.80} = \frac{43700}{11270} \approx 3.88\text{ m}

    Because you added atmospheric pressure in Step 2, the numerator computed the sum of the pressures rather than the gauge pressure difference, leading to an oversized depth.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified the hydrostatic pressure formula for an open tank.

You recognized that the tank radius is irrelevant to calculating pressure at depth.

You carried out the arithmetic and unit division accurately based on your rearranged formula.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Algebraic Rearrangement Error

You accidentally added atmospheric pressure instead of subtracting it when transposing it to the other side.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing the total (absolute) pressure with the hydrostatic pressure contribution of the fluid column alone. The fluid column only accounts for the pressure above atmospheric pressure (Pgauge=P−PatmP_{\text{gauge}} = P - P_{\text{atm}}).

REASONING PATH
Your ACEpath teacher’s suggested approach
Gauge vs. Absolute Pressure
  • The liquid column exerts gauge pressure: Pgauge=ρgh=Pabsolute−PatmP_{\text{gauge}} = \rho g h = P_{\text{absolute}} - P_{\text{atm}}.

  • Whenever you solve for depth from absolute pressure, always subtract PatmP_{\text{atm}} to find the pressure contribution of the fluid.

Physical Reality Check
  • The fluid contribution must be less than the total bottom pressure.

  • Notice that P−Patm=0.437×105 PaP - P_{\text{atm}} = 0.437 \times 10^5\text{ Pa}, whereas adding them gave 2.463×105 Pa2.463 \times 10^5\text{ Pa}, which would require a fluid column almost six times deeper.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Pgauge=1.450×105 Pa−1.013×105 Pa=4.37×104 PaP_{\text{gauge}} = 1.450 \times 10^5\text{ Pa} - 1.013 \times 10^5\text{ Pa} = 4.37 \times 10^4\text{ Pa}

  2. h=P−Patmρg=43700 Pa(1.15×103 kg/m3)(9.80 m/s2)h = \frac{P - P_{\text{atm}}}{\rho g} = \frac{43700\text{ Pa}}{(1.15 \times 10^3\text{ kg/m}^3)(9.80\text{ m/s}^2)}

  3. h=4370011270≈3.88 mh = \frac{43700}{11270} \approx 3.88\text{ m}

Final answer

h=3.88 mh = 3.88\text{ m}

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice isolating variables in additive equations (A=B+C  ⟹  C=A−BA = B + C \implies C = A - B).

  • Verify that gauge pressure is always the difference between absolute pressure and ambient atmospheric pressure.

OverviewACEpath Teacher's Diagnosis

03 The student unnecessarily multiplies pressure by the tank cross-sectional area to find force but forgets to convert force back, dividing force by ρg to solve for depth.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    Pgauge=P−Patm=1.450×105−1.013×105=43700 PaP_{\text{gauge}} = P - P_{\text{atm}} = 1.450 \times 10^5 - 1.013 \times 10^5 = 43700\text{ Pa}

  2. Step 2

    A=πR2=3.1416×(1.20)2≈4.524 m2  ⟹  F=Pgauge×A=43700×4.524=197699 NA = \pi R^2 = 3.1416 \times (1.20)^2 \approx 4.524\text{ m}^2 \implies F = P_{\text{gauge}} \times A = 43700 \times 4.524 = 197699\text{ N}

  3. Step 3

    h=Fρg=1976991.15×103×9.80≈17.54 mh = \frac{F}{\rho g} = \frac{197699}{1.15 \times 10^3 \times 9.80} \approx 17.54\text{ m}

    Correct

    h=Pgaugeρg=43 700 Pa(1.15×103 kg/m3)(9.80 m/s2)≈3.88 mh = \frac{P_{\text{gauge}}}{\rho g} = \frac{43\,700\text{ Pa}}{(1.15 \times 10^3\text{ kg/m}^3)(9.80\text{ m/s}^2)} \approx 3.88\text{ m}

    You divided force FF by ρg\rho g instead of pressure PgaugeP_{\text{gauge}} by ρg\rho g. Because F=mg=ρVgF = m g = \rho V g, the quantity Fρg\frac{F}{\rho g} yields the fluid volume VV in m3\text{m}^3, not the liquid depth hh in m\text{m}.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified that the fluid column only needs to support the gauge pressure P−PatmP - P_{\text{atm}}.

You accurately computed the gauge pressure as 43 700 Pa43\,700\text{ Pa}.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Dimensional Inconsistency (Force vs. Pressure)

You substituted the total force FF into the hydrostatic depth equation where gauge pressure PgaugeP_{\text{gauge}} was required.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated pressure and force interchangeably when solving for depth. Dividing force by ρg\rho g yields volume (V=FρgV = \frac{F}{\rho g}) rather than height (h=Pρg=FρgAh = \frac{P}{\rho g} = \frac{F}{\rho g A}).

REASONING PATH
Your ACEpath teacher’s suggested approach
Dimensional Check
  • Always verify that both sides of an isolated equation have matching physical units: [Pρg]=N/m2N/m3=m[\frac{P}{\rho g}] = \frac{\text{N/m}^2}{\text{N/m}^3} = \text{m}, whereas [Fρg]=NN/m3=m3[\frac{F}{\rho g}] = \frac{\text{N}}{\text{N/m}^3} = \text{m}^3.

  • Check that the numerator has units of pressure (pascals), not force (newtons), before dividing by specific weight ρg\rho g.

Geometry Independence in Hydrostatics
  • Hydrostatic pressure at depth hh in a static, uniform fluid depends solely on density, gravity, and depth (P=ρghP = \rho g h), completely independent of tank radius, cross-sectional area, or container shape.

  • Solve directly for depth using h=Pgaugeρgh = \frac{P_{\text{gauge}}}{\rho g} without calculating area or force.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Relate gauge pressure directly to fluid column depth using Pgauge=ρghP_{\text{gauge}} = \rho g h.

  2. Isolate depth: h=Pgaugeρgh = \frac{P_{\text{gauge}}}{\rho g}.

  3. Substitute the given values: h=43 700 Pa(1.15×103 kg/m3)(9.80 m/s2)=43 70011 270 m≈3.878 mh = \frac{43\,700\text{ Pa}}{(1.15 \times 10^3\text{ kg/m}^3)(9.80\text{ m/s}^2)} = \frac{43\,700}{11\,270}\text{ m} \approx 3.878\text{ m}.

Final answer

h=3.88 mh = 3.88\text{ m}

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice identifying extraneous geometric parameters (such as diameter or radius) in hydrostatic pressure problems.

  • Perform a quick dimensional sanity check whenever isolating geometric dimensions from fluid equations.

Lock it in

Similar question

01

A swimming pool open to the air (Patm=1.01×105 PaP_{\text{atm}} = 1.01 \times 10^5\text{ Pa}) contains fresh water of density ρ=1.00×103 kg/m3\rho = 1.00 \times 10^3\text{ kg/m}^3. At what depth hh is the absolute pressure equal to 1.30×105 Pa1.30 \times 10^5\text{ Pa}? Use g=9.80 m/s2g = 9.80\text{ m/s}^2.

Answer

h≈2.96 mh \approx 2.96\text{ m}. Calculate gauge pressure Pgauge=P−Patm=1.30×105−1.01×105=2.90×104 PaP_{\text{gauge}} = P - P_{\text{atm}} = 1.30 \times 10^5 - 1.01 \times 10^5 = 2.90 \times 10^4\text{ Pa}. Then h=Pgaugeρg=29000(1000)(9.80)≈2.96 mh = \frac{P_{\text{gauge}}}{\rho g} = \frac{29000}{(1000)(9.80)} \approx 2.96\text{ m}.

02

An open vat filled with oil (ρ=880 kg/m3\rho = 880\text{ kg/m}^3) is located in a high-altitude lab where atmospheric pressure is Patm=8.50×104 PaP_{\text{atm}} = 8.50 \times 10^4\text{ Pa}. A pressure gauge at the bottom measures an absolute pressure of 1.25×105 Pa1.25 \times 10^5\text{ Pa}. Determine the height of the oil column. Take g=9.80 m/s2g = 9.80\text{ m/s}^2.

Answer

h≈4.64 mh \approx 4.64\text{ m}. First find the gauge pressure exerted by the oil: P−Patm=1.25×105−8.50×104=4.00×104 PaP - P_{\text{atm}} = 1.25 \times 10^5 - 8.50 \times 10^4 = 4.00 \times 10^4\text{ Pa}. Then calculate depth: h=40000(880)(9.80)=400008624≈4.64 mh = \frac{40000}{(880)(9.80)} = \frac{40000}{8624} \approx 4.64\text{ m}.

03

A vertical cylindrical tank open to the atmosphere (Patm=1.00×105 PaP_{\text{atm}} = 1.00 \times 10^5\text{ Pa}) has radius r=0.75 mr = 0.75\text{ m}. The maximum total force the circular base can withstand before failing is 3.00×105 N3.00 \times 10^5\text{ N}. If the tank is filled with a solvent of density ρ=920 kg/m3\rho = 920\text{ kg/m}^3 (g=9.80 m/s2g = 9.80\text{ m/s}^2), what is the maximum permissible liquid depth hh?

Answer

h≈7.74 mh \approx 7.74\text{ m}. Area of base A=πr2=π(0.75)2≈1.7671 m2A = \pi r^2 = \pi (0.75)^2 \approx 1.7671\text{ m}^2. Maximum allowable absolute pressure is Pmax⁡=FA=3.00×1051.7671≈1.6976×105 PaP_{\max} = \frac{F}{A} = \frac{3.00 \times 10^5}{1.7671} \approx 1.6976 \times 10^5\text{ Pa}. The maximum gauge pressure is Pgauge=Pmax⁡−Patm=6.976×104 PaP_{\text{gauge}} = P_{\max} - P_{\text{atm}} = 6.976 \times 10^4\text{ Pa}. Solving for depth: h=69760(920)(9.80)=697609016≈7.74 mh = \frac{69760}{(920)(9.80)} = \frac{69760}{9016} \approx 7.74\text{ m}.

Loading workspace…