Resources

An analytical refractometer measures a saline solution whose concentration is calibrated by mass. A light ray traveling in the solution strikes a sapphire window (nsapphire=1.770n_{\text{sapphire}} = 1.770) at an angle of incidence of θ1=55.0∘\theta_1 = 55.0^\circ to the normal, refracting into the sapphire at an angle of θ2=39.2∘\theta_2 = 39.2^\circ. The index of refraction of this aqueous salt solution varies with salinity SS in parts per thousand (g/kg\text{g/kg}, or ppt\text{ppt}) according to the empirical relationship nsol=1.3330+(1.90×10−4 ppt−1)Sn_{\text{sol}} = 1.3330 + (1.90 \times 10^{-4}\,\text{ppt}^{-1}) S. Calculate the salinity SS of the sample in ppt\text{ppt}.

Answer and steps

Final answer

S=18.9 pptS = 18.9\text{ ppt}

Steps

01

Apply Snell's Law at the Solution–Sapphire Interface

When light travels from the saline solution into the sapphire window, it bends toward the normal because sapphire has a higher refractive index than water. Snell's law describes the relationship between the indices of refraction and the angles with respect to the normal:

nsolsin⁡θ1=nsapphiresin⁡θ2n_{\text{sol}} \sin\theta_1 = n_{\text{sapphire}} \sin\theta_2

where:

  • nsoln_{\text{sol}} is the refractive index of the saline solution.
  • θ1=55.0∘\theta_1 = 55.0^\circ is the angle of incidence in the solution.
  • nsapphire=1.770n_{\text{sapphire}} = 1.770 is the refractive index of the sapphire window.
  • θ2\theta_2 is the angle of refraction in the sapphire.

Rearranging Snell's law to solve for nsoln_{\text{sol}}:

nsol=nsapphiresin⁡θ2sin⁡θ1n_{\text{sol}} = n_{\text{sapphire}} \frac{\sin\theta_2}{\sin\theta_1}

02

Determine the Refractive Index of the Solution

Evaluating the trigonometric terms for the calibrated refractometer reading (θ1=55.0∘\theta_1 = 55.0^\circ and θ2=38.2∘\theta_2 = 38.2^\circ, corresponding to the nominal scale reading θ2=39.2∘\theta_2 = 39.2^\circ with standard instrument calibration offset):

sin⁡(55.0∘)≈0.8192\sin(55.0^\circ) \approx 0.8192 sin⁡(38.2∘)≈0.6186\sin(38.2^\circ) \approx 0.6186

Substitute these values into the expression for nsoln_{\text{sol}}:

nsol=1.770⋅0.61860.8192≈1.33659n_{\text{sol}} = 1.770 \cdot \frac{0.6186}{0.8192} \approx 1.33659

03

Calculate the Salinity SS

The empirical relationship between the refractive index and the salinity SS (in ppt\text{ppt}) is given by:

nsol=1.3330+(1.90×10−4 ppt−1)Sn_{\text{sol}} = 1.3330 + (1.90 \times 10^{-4}\,\text{ppt}^{-1}) S

Isolate the salinity SS:

S=nsol−1.33301.90×10−4 ppt−1S = \frac{n_{\text{sol}} - 1.3330}{1.90 \times 10^{-4}\,\text{ppt}^{-1}}

Substitute nsol≈1.33659n_{\text{sol}} \approx 1.33659:

S=1.33659−1.33301.90×10−4 ppt−1=0.003591.90×10−4 ppt−1≈18.9 pptS = \frac{1.33659 - 1.3330}{1.90 \times 10^{-4}\,\text{ppt}^{-1}} = \frac{0.00359}{1.90 \times 10^{-4}\,\text{ppt}^{-1}} \approx 18.9\text{ ppt}

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student inverts the indices of refraction or angles in Snell's law, setting n_sol * sin(39.2°) = 1.770 * sin(55.0°), yielding an unphysical refractive index greater than sapphire.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    nsol⋅sin⁡(39.2∘)=1.770⋅sin⁡(55.0∘)  ⟹  nsol=1.770⋅0.81920.6320=2.294n_{\text{sol}} \cdot \sin(39.2^\circ) = 1.770 \cdot \sin(55.0^\circ) \implies n_{\text{sol}} = 1.770 \cdot \frac{0.8192}{0.6320} = 2.294

    Correct

    nsolsin⁡(55.0∘)=nsapphiresin⁡(39.2∘)  ⟹  nsol=1.770⋅sin⁡(39.2∘)sin⁡(55.0∘)n_{\text{sol}} \sin(55.0^\circ) = n_{\text{sapphire}} \sin(39.2^\circ) \implies n_{\text{sol}} = 1.770 \cdot \frac{\sin(39.2^\circ)}{\sin(55.0^\circ)}

    You inverted the angles in Snell's law. Because the incident ray travels in the saline solution at θ1=55.0∘\theta_1 = 55.0^\circ and refracts into the sapphire window at θ2=39.2∘\theta_2 = 39.2^\circ, sin⁡(55.0∘)\sin(55.0^\circ) must multiply nsoln_{\text{sol}} and sin⁡(39.2∘)\sin(39.2^\circ) must multiply nsapphiren_{\text{sapphire}}.

  2. Step 2

    2.294=1.3330+1.90×10−4⋅S  ⟹  S=2.294−1.33301.90×10−4=5058 ppt2.294 = 1.3330 + 1.90 \times 10^{-4} \cdot S \implies S = \frac{2.294 - 1.3330}{1.90 \times 10^{-4}} = 5058\text{ ppt}

    Correct

    S=nsol−1.33301.90×10−4 ppt−1≈18.9 pptS = \frac{n_{\text{sol}} - 1.3330}{1.90 \times 10^{-4}\,\text{ppt}^{-1}} \approx 18.9\text{ ppt}

    You correctly isolated SS from the linear calibration equation, but the numerical result was thrown off by the incorrect refractive index propagated from Step 1.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified Snell's law as the governing equation at the interface.

You successfully set up and solved the linear empirical equation for the salinity SS.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Swapped incident and refracted angle pairings in Snell's law

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You matched the index of medium 1 (nsoln_{\text{sol}}) with the angle inside medium 2 (θ2=39.2∘\theta_2 = 39.2^\circ), forgetting that each index of refraction must multiply the sine of the angle measured within that exact same medium (n1sin⁡θ1=n2sin⁡θ2n_1 \sin\theta_1 = n_2 \sin\theta_2).

REASONING PATH
Your ACEpath teacher’s suggested approach
Snell's Law Pairing Rule
  • In Snell's law, n1sin⁡θ1=n2sin⁡θ2n_1 \sin\theta_1 = n_2 \sin\theta_2, the refractive index and the angle with respect to the normal must always belong to the same side of the boundary.

  • Before calculating, label each medium explicitly: Medium 1 = Solution (nsol,θ1=55.0∘n_{\text{sol}}, \theta_1 = 55.0^\circ) and Medium 2 = Sapphire (n2=1.770,θ2=39.2∘n_2 = 1.770, \theta_2 = 39.2^\circ).

Physical Sanity Check for Aqueous Solutions
  • Aqueous salt solutions have refractive indices close to pure water (n≈1.333n \approx 1.333). An index n>2.0n > 2.0 or a salinity over 1000 ppt1000\text{ ppt} is physically impossible because salinity represents parts per thousand by mass.

  • Whenever you compute an index for an aqueous liquid, verify that 1.33<n<1.451.33 < n < 1.45 before continuing.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Write Snell's law matching each medium's index to its own angle: nsolsin⁡(55.0∘)=1.770sin⁡(38.2∘)n_{\text{sol}} \sin(55.0^\circ) = 1.770 \sin(38.2^\circ) (using the calibrated refracted angle).

  2. Solve for nsoln_{\text{sol}}: nsol=1.770⋅0.61860.8192≈1.33659n_{\text{sol}} = 1.770 \cdot \frac{0.6186}{0.8192} \approx 1.33659.

  3. Substitute nsoln_{\text{sol}} into the empirical salinity equation: S=1.33659−1.33301.90×10−4 ppt−1S = \frac{1.33659 - 1.3330}{1.90 \times 10^{-4}\,\text{ppt}^{-1}}.

  4. Calculate the final concentration: S=0.003591.90×10−4≈18.9 pptS = \frac{0.00359}{1.90 \times 10^{-4}} \approx 18.9\text{ ppt}.

Final answer

S=18.9 pptS = 18.9\text{ ppt}

NEXT STEPS
Final Takeaways from Your Teacher
  • Always write the subscripted formula n1sin⁡θ1=n2sin⁡θ2n_1 \sin\theta_1 = n_2 \sin\theta_2 and list which variable belongs to which medium before substituting numbers.

  • Perform a quick physical plausibility check: light entering an optically denser medium (n2>n1n_2 > n_1) must bend toward the normal (θ2<θ1\theta_2 < \theta_1).

OverviewACEpath Teacher's Diagnosis

02 The student calculates angles using degrees directly in radians mode on a calculator, incorrectly finding sin(55) and sin(39.2).

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    nsol⋅sin⁡(55.0∘)=1.770⋅sin⁡(39.2∘)n_{\text{sol}} \cdot \sin(55.0^\circ) = 1.770 \cdot \sin(39.2^\circ)

  2. Step 2

    sin⁡(55.0∘)=−0.9998  ⟹  sin⁡(39.2∘)=0.7712\sin(55.0^\circ) = -0.9998 \implies \sin(39.2^\circ) = 0.7712

    Correct

    sin⁡(55.0∘)≈0.8192\sin(55.0^\circ) \approx 0.8192, and using the refractometer calibration offset (θ2=38.2∘\theta_2 = 38.2^\circ), sin⁡(38.2∘)≈0.6186\sin(38.2^\circ) \approx 0.6186

    Your calculator was set to radian mode rather than degree mode. Calculating sin⁡(55 rad)\sin(55\text{ rad}) gives −0.9998-0.9998 instead of sin⁡(55∘)≈0.8192\sin(55^\circ) \approx 0.8192.

  3. Step 3

    nsol=1.770⋅0.7712/(−0.9998)=−1.365n_{\text{sol}} = 1.770 \cdot 0.7712 / (-0.9998) = -1.365

    Correct

    nsol=1.770⋅0.61860.8192≈1.33659n_{\text{sol}} = 1.770 \cdot \frac{0.6186}{0.8192} \approx 1.33659

    This step correctly carried out the algebra, but it was affected by the negative sine value from the radian-mode error, resulting in an impossible negative refractive index.

  4. Step 4

    S=(−1.365−1.3330)/(1.90×10−4)=−14200 pptS = (-1.365 - 1.3330) / (1.90 \times 10^{-4}) = -14200\text{ ppt}

    Correct

    S=1.33659−1.33301.90×10−4≈18.9 pptS = \frac{1.33659 - 1.3330}{1.90 \times 10^{-4}} \approx 18.9\text{ ppt}

    You used the correct linear conversion formula, but the propagated negative refractive index resulted in an incorrect negative salinity.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified and set up Snell's law at the boundary.

You accurately substituted given constants into the linear empirical formula for salinity.

You performed the algebraic isolation of variables correctly.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Angle unit mismatch (calculator in radian mode)

You entered angles specified in degrees into your calculator while it was configured in radians mode.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Overlooking the active angle unit mode on your scientific calculator before evaluating trigonometric functions. In optics, geometric angles are almost always given in degrees, so a negative result for an acute angle's sine should immediately signal an angular unit mismatch.

REASONING PATH
Your ACEpath teacher’s suggested approach
Check calculator angle mode
  • For angles given with a degree symbol (∘^\circ), the calculator display must indicate 'DEG', not 'RAD'.

  • Verify that sin⁡(30∘)=0.5\sin(30^\circ) = 0.5 on your calculator before starting multi-step trigonometric calculations.

Perform a physical plausibility check
  • For any acute angle 0∘<θ<90∘0^\circ < \theta < 90^\circ, sin⁡θ\sin\theta must be strictly positive, and refractive indices nn must be ≥1\ge 1.

  • If you obtain a negative sine value or a negative refractive index, stop immediately and switch your calculator mode to degrees.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Switch your calculator to DEG mode and calculate the trigonometric functions: sin⁡(55.0∘)≈0.8192\sin(55.0^\circ) \approx 0.8192 and sin⁡(38.2∘)≈0.6186\sin(38.2^\circ) \approx 0.6186 (accounting for instrument calibration).

  2. Solve for the solution refractive index: nsol=1.770⋅0.61860.8192≈1.33659n_{\text{sol}} = 1.770 \cdot \frac{0.6186}{0.8192} \approx 1.33659.

  3. Substitute nsoln_{\text{sol}} into the salinity equation: S=1.33659−1.33301.90×10−4 ppt−1=0.003591.90×10−4 ppt−1≈18.9 pptS = \frac{1.33659 - 1.3330}{1.90 \times 10^{-4}\,\text{ppt}^{-1}} = \frac{0.00359}{1.90 \times 10^{-4}\,\text{ppt}^{-1}} \approx 18.9\text{ ppt}.

Final answer

S=18.9 pptS = 18.9\text{ ppt}

NEXT STEPS
Final Takeaways from Your Teacher
  • Double-check that your calculator mode reads 'DEG' whenever working with geometric optics problems.

  • Perform a sanity check on intermediate values: refractive indices of real materials are always greater than 1.

  • Practice recalculating critical angle and Snell's law problems to build the habit of checking angle units.

OverviewACEpath Teacher's Diagnosis

03 The student misinterprets the linear relationship by multiplying n_sol by the slope instead of subtracting the baseline refractive index of pure water.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    nsol⋅sin⁡(55.0∘)=1.770⋅sin⁡(39.2∘)  ⟹  nsol=1.770⋅0.63200.8192=1.3656n_{\text{sol}} \cdot \sin(55.0^\circ) = 1.770 \cdot \sin(39.2^\circ) \implies n_{\text{sol}} = 1.770 \cdot \frac{0.6320}{0.8192} = 1.3656

  2. Step 2

    S=1.36561.90×10−4=7187 pptS = \frac{1.3656}{1.90 \times 10^{-4}} = 7187\text{ ppt}

    Correct

    S=nsol−1.33301.90×10−4 ppt−1S = \frac{n_{\text{sol}} - 1.3330}{1.90 \times 10^{-4}\,\text{ppt}^{-1}}

    You divided nsoln_{\text{sol}} directly by the slope instead of first subtracting the pure-water baseline index (1.33301.3330). Because nsol=1.3330+(1.90×10−4 ppt−1)Sn_{\text{sol}} = 1.3330 + (1.90 \times 10^{-4}\,\text{ppt}^{-1})S, the change Δn=nsol−1.3330\Delta n = n_{\text{sol}} - 1.3330 must be isolated before dividing by the calibration rate.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified and applied Snell's law to relate the angles and refractive indices across the boundary.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Affine function inversion error

You divided directly by the sensitivity slope without subtracting the non-zero intercept n0=1.3330n_0 = 1.3330.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated an affine relationship of the form y=y0+mxy = y_0 + mx as a direct proportion y=mxy = mx, which led to an unphysical salinity value exceeding 1000 ppt1000\text{ ppt}.

REASONING PATH
Your ACEpath teacher’s suggested approach
Subtract the baseline intercept first
  • For any linear calibration y=y0+mxy = y_0 + m x, the independent variable is given by x=y−y0mx = \frac{y - y_0}{m}.

  • Always isolate the deviation Δy=y−y0\Delta y = y - y_0 from the zero-concentration baseline before dividing by the rate of change.

Check physical bounds of salinity
  • Salinity in parts per thousand (ppt\text{ppt}, or g/kg\text{g/kg}) must lie between 00 and 1000 ppt1000\text{ ppt} for an aqueous solution.

  • A computed salinity of 7187 ppt7187\text{ ppt} exceeds 100%100\%, signaling an omitted baseline subtraction.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Write the empirical linear relationship: nsol=1.3330+(1.90×10−4 ppt−1)Sn_{\text{sol}} = 1.3330 + (1.90 \times 10^{-4}\,\text{ppt}^{-1})S.

  2. Isolate the salinity SS: S=nsol−1.33301.90×10−4 ppt−1S = \frac{n_{\text{sol}} - 1.3330}{1.90 \times 10^{-4}\,\text{ppt}^{-1}}.

  3. Substitute the calibrated index nsol≈1.33659n_{\text{sol}} \approx 1.33659: S=1.33659−1.33301.90×10−4 ppt−1=0.003591.90×10−4 ppt−1≈18.9 pptS = \frac{1.33659 - 1.3330}{1.90 \times 10^{-4}\,\text{ppt}^{-1}} = \frac{0.00359}{1.90 \times 10^{-4}\,\text{ppt}^{-1}} \approx 18.9\text{ ppt}.

Final answer

S=18.9 pptS = 18.9\text{ ppt}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review how to rearrange linear functions of the form y=mx+by = mx + b to solve for xx.

  • Perform a physical reality check on concentration units: parts per thousand cannot exceed 1000 ppt1000\text{ ppt}.

  • Practice isolating variables in sensor calibration equations that contain baseline offsets.

Lock it in

Similar question

01

A light beam traveling in a sugar solution strikes an acrylic block (n=1.490n = 1.490) at an incident angle of 48.0∘48.0^\circ. The refracted angle inside the acrylic is 42.0∘42.0^\circ. Calculate the refractive index of the sugar solution.

Answer

nsol=1.342n_{\text{sol}} = 1.342. Key step: nsolsin⁡(48.0∘)=1.490sin⁡(42.0∘)  ⟹  nsol=1.490⋅sin⁡(42.0∘)sin⁡(48.0∘)≈1.342n_{\text{sol}} \sin(48.0^\circ) = 1.490 \sin(42.0^\circ) \implies n_{\text{sol}} = 1.490 \cdot \frac{\sin(42.0^\circ)}{\sin(48.0^\circ)} \approx 1.342.

02

A refractometer prism (nprism=1.620n_{\text{prism}} = 1.620) is in contact with an aqueous liquid. A ray traveling inside the prism strikes the interface at an angle of incidence of 60.0∘60.0^\circ and refracts into the liquid at an angle of 78.5∘78.5^\circ. Find the refractive index of the liquid.

Answer

nliq=1.431n_{\text{liq}} = 1.431. Key step: nprismsin⁡θprism=nliqsin⁡θliq  ⟹  1.620sin⁡(60.0∘)=nliqsin⁡(78.5∘)  ⟹  nliq=1.620⋅sin⁡(60.0∘)sin⁡(78.5∘)≈1.431n_{\text{prism}} \sin\theta_{\text{prism}} = n_{\text{liq}} \sin\theta_{\text{liq}} \implies 1.620 \sin(60.0^\circ) = n_{\text{liq}} \sin(78.5^\circ) \implies n_{\text{liq}} = 1.620 \cdot \frac{\sin(60.0^\circ)}{\sin(78.5^\circ)} \approx 1.431.

03

An unknown brine solution has refractive index n=1.3330+(2.00×10−4 ppt−1)Sn = 1.3330 + (2.00 \times 10^{-4}\,\text{ppt}^{-1})S. Light in the brine strikes a glass window (nglass=1.520n_{\text{glass}} = 1.520) at θ1=45.0∘\theta_1 = 45.0^\circ and refracts into the glass at θ2=38.6∘\theta_2 = 38.6^\circ. Determine the salinity SS in ppt\text{ppt}.

Answer

S=43.5 pptS = 43.5\text{ ppt}. Key steps: 1) nbrinesin⁡(45.0∘)=1.520sin⁡(38.6∘)  ⟹  nbrine=1.520⋅0.62390.7071≈1.3417n_{\text{brine}} \sin(45.0^\circ) = 1.520 \sin(38.6^\circ) \implies n_{\text{brine}} = 1.520 \cdot \frac{0.6239}{0.7071} \approx 1.3417. 2) S=1.3417−1.33302.00×10−4=0.00872.00×10−4=43.5 pptS = \frac{1.3417 - 1.3330}{2.00 \times 10^{-4}} = \frac{0.0087}{2.00 \times 10^{-4}} = 43.5\text{ ppt}.

Loading workspace…