Resources

In a university thermodynamics laboratory, students evaluate the operational efficiency of an experimental miniature stirling-cycle heat engine coupled to a water-bath calorimeter. The engine draws heat from an electric heating element delivering a steady thermal power of Q˙H=120 W\dot{Q}_H = 120\text{ W} at a hot-end temperature of TH=425 KT_H = 425\text{ K}. The cold end is clamped to an aluminum block submerged in a well-insulated calorimeter filled with mw=0.850 kgm_w = 0.850\text{ kg} of liquid water (cw=4184 J/(kg⋅K)c_w = 4184\text{ J}/(\text{kg}\cdot\text{K})) initially at T0=293.15 KT_0 = 293.15\text{ K}. During an experimental run lasting Δt=600 s\Delta t = 600\text{ s}, a prony friction brake measures a constant brake torque of τ=0.140 N⋅m\tau = 0.140\text{ N}\cdot\text{m} at an engine shaft angular speed of ω=180 rad/s\omega = 180\text{ rad/s}. Assuming heat loss to the ambient surroundings is negligible: (a) calculate the mechanical shaft power output Pmech\mathcal{P}_{\text{mech}} and the net mechanical work output WoutW_{\text{out}} over the 600 s600\text{ s} run, (b) calculate the actual experimental thermal efficiency ηexp\eta_{\text{exp}} and compare it with the theoretical Carnot limit ηCarnot\eta_{\text{Carnot}} (using TC=T0T_C = T_0), and (c) calculate the final temperature of the calorimeter water TfT_f at the conclusion of the test.

Answer and steps

Final answer

(a) Pmech=25.2 W\mathcal{P}_{\text{mech}} = 25.2\text{ W} and Wout=1.51×104 JW_{\text{out}} = 1.51 \times 10^4\text{ J}; (b) ηexp=0.210\eta_{\text{exp}} = 0.210 (or 21.0%21.0\%) compared to ηCarnot=0.310\eta_{\text{Carnot}} = 0.310 (or 31.0%31.0\%); (c) Tf=309.2 KT_f = 309.2\text{ K} (or 36.0∘C36.0^\circ\text{C}).

Steps

Part (a): Mechanical Power and Work Output

The mechanical power output Pmech\mathcal{P}_{\text{mech}} delivered by a rotating shaft subject to a braking torque τ\tau at an angular velocity ω\omega is given by:

Pmech=τω\mathcal{P}_{\text{mech}} = \tau \omega

Substitute the given values:

Pmech=(0.140 N⋅m)⋅(180 rad/s)=25.2 W\mathcal{P}_{\text{mech}} = (0.140\text{ N}\cdot\text{m}) \cdot (180\text{ rad/s}) = 25.2\text{ W}

The total net mechanical work WoutW_{\text{out}} produced over the time interval Δt=600 s\Delta t = 600\text{ s} is:

Wout=PmechΔt=25.2 W⋅600 s=15120 J≈1.51×104 JW_{\text{out}} = \mathcal{P}_{\text{mech}} \Delta t = 25.2\text{ W} \cdot 600\text{ s} = 15120\text{ J} \approx 1.51 \times 10^4\text{ J}


Part (b): Experimental and Carnot Thermal Efficiencies

The total heat input QHQ_H supplied to the engine at the hot reservoir over the duration Δt\Delta t is:

QH=Q˙HΔt=120 W⋅600 s=72000 JQ_H = \dot{Q}_H \Delta t = 120\text{ W} \cdot 600\text{ s} = 72000\text{ J}

The experimental thermal efficiency ηexp\eta_{\text{exp}} is the ratio of useful work output to heat input (or mechanical power to heat input rate):

ηexp=WoutQH=PmechQ˙H=25.2 W120 W=0.210(21.0%)\eta_{\text{exp}} = \frac{W_{\text{out}}}{Q_H} = \frac{\mathcal{P}_{\text{mech}}}{\dot{Q}_H} = \frac{25.2\text{ W}}{120\text{ W}} = 0.210\quad (21.0\%)

The theoretical maximum efficiency between the two thermal reservoirs is defined by the Carnot efficiency:

ηCarnot=1−TCTH\eta_{\text{Carnot}} = 1 - \frac{T_C}{T_H}

Using the initial cold reservoir temperature TC=T0=293.15 KT_C = T_0 = 293.15\text{ K} and hot reservoir temperature TH=425 KT_H = 425\text{ K}:

ηCarnot=1−293.15 K425 K=1−0.6898=0.3102≈0.310(31.0%)\eta_{\text{Carnot}} = 1 - \frac{293.15\text{ K}}{425\text{ K}} = 1 - 0.6898 = 0.3102 \approx 0.310\quad (31.0\%)

As expected by the Second Law of Thermodynamics for real engines with internal irreversibilities and friction, ηexp<ηCarnot\eta_{\text{exp}} < \eta_{\text{Carnot}} (21.0%<31.0%21.0\% < 31.0\%).


Part (c): Final Temperature of the Calorimeter Water

By conservation of energy (First Law of Thermodynamics applied to the steady engine cycle), the heat rejected to the cold reservoir QCQ_C equals the total heat supplied minus the mechanical work produced:

QC=QH−Wout=72000 J−15120 J=56880 JQ_C = Q_H - W_{\text{out}} = 72000\text{ J} - 15120\text{ J} = 56880\text{ J}

Assuming negligible losses to the surroundings, all rejected heat QCQ_C is absorbed by the water in the calorimeter:

QC=mwcw(Tf−T0)Q_C = m_w c_w (T_f - T_0)

Solve for the temperature increase ΔT=Tf−T0\Delta T = T_f - T_0:

ΔT=QCmwcw=56880 J0.850 kg⋅4184 J/(kg⋅K)=56880 J3556.4 J/K≈15.99 K\Delta T = \frac{Q_C}{m_w c_w} = \frac{56880\text{ J}}{0.850\text{ kg} \cdot 4184\text{ J}/(\text{kg}\cdot\text{K})} = \frac{56880\text{ J}}{3556.4\text{ J/K}} \approx 15.99\text{ K}

Calculate the final water temperature TfT_f:

Tf=T0+ΔT=293.15 K+15.99 K=309.14 K≈309.2 KT_f = T_0 + \Delta T = 293.15\text{ K} + 15.99\text{ K} = 309.14\text{ K} \approx 309.2\text{ K}

Expressed in degrees Celsius:

Tf=309.2 K−273.15=36.0∘CT_f = 309.2\text{ K} - 273.15 = 36.0^\circ\text{C}

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student forgets that the engine converts part of the input heat into mechanical work and assumes all input heat is dumped into the calorimeter water.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    Pmech=τ⋅ω=0.140⋅180=25.2 W  ⟹  Wout=Pmech⋅Δt=25.2⋅600=15120 JP_{\text{mech}} = \tau \cdot \omega = 0.140 \cdot 180 = 25.2\text{ W} \implies W_{\text{out}} = P_{\text{mech}} \cdot \Delta t = 25.2 \cdot 600 = 15120\text{ J}

  2. Step 2

    ηexp=PmechQ˙H=25.2120=0.210=21.0%  ⟹  ηCarnot=1−293.15425=0.310=31.0%  ⟹  ηexp<ηCarnot\eta_{\text{exp}} = \frac{P_{\text{mech}}}{\dot{Q}_H} = \frac{25.2}{120} = 0.210 = 21.0\% \implies \eta_{\text{Carnot}} = 1 - \frac{293.15}{425} = 0.310 = 31.0\% \implies \eta_{\text{exp}} < \eta_{\text{Carnot}}

  3. Step 3

    Qin=Q˙H⋅Δt=120⋅600=72000 J  ⟹  ΔT=Qinmw⋅cw=720000.850⋅4184=20.24 KQ_{\text{in}} = \dot{Q}_H \cdot \Delta t = 120 \cdot 600 = 72000\text{ J} \implies \Delta T = \frac{Q_{\text{in}}}{m_w \cdot c_w} = \frac{72000}{0.850 \cdot 4184} = 20.24\text{ K}

    Correct

    QC=QH−Wout=72000 J−15120 J=56880 J  ⟹  ΔT=QCmwcw=56880 J0.850 kg⋅4184 J/(kg⋅K)≈15.99 KQ_C = Q_H - W_{\text{out}} = 72000\text{ J} - 15120\text{ J} = 56880\text{ J} \implies \Delta T = \frac{Q_C}{m_w c_w} = \frac{56880\text{ J}}{0.850\text{ kg} \cdot 4184\text{ J}/(\text{kg}\cdot\text{K})} \approx 15.99\text{ K}

    A heat engine converts part of the input heat into mechanical work (Wout=15120 JW_{\text{out}} = 15120\text{ J}). Only the remaining rejected heat, QC=QH−WoutQ_C = Q_H - W_{\text{out}}, enters the calorimeter water.

  4. Step 4

    Tf=293.15+20.24=313.39 KT_f = 293.15 + 20.24 = 313.39\text{ K}

    Correct

    Tf=T0+ΔT=293.15 K+15.99 K≈309.2 KT_f = T_0 + \Delta T = 293.15\text{ K} + 15.99\text{ K} \approx 309.2\text{ K}

    Your final temperature evaluation followed correctly from your calculated ΔT\Delta T, but carries over the error from omitting WoutW_{\text{out}}.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly calculated the mechanical power output and net work from the brake torque and angular speed.

You evaluated both the actual experimental efficiency and the theoretical Carnot efficiency accurately.

You correctly calculated the total heat supplied by the electric heater over the test duration.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Heat engine energy balance omission

You equated the heat deposited into the cold reservoir to the total heat input QHQ_H, overlooking that the engine converts a fraction of QHQ_H into work.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Treating heat engine heat rejection as simple thermal conduction rather than applying the First Law of Thermodynamics cycle balance QH=Wout+QCQ_H = W_{\text{out}} + Q_C.

REASONING PATH
Your ACEpath teacher’s suggested approach
First Law for Cyclic Heat Engines
  • QH=Wout+QCQ_H = W_{\text{out}} + Q_C

  • Always subtract the net work output from the heat input to determine the heat dumped into the cold reservoir (QC=QH−WoutQ_C = Q_H - W_{\text{out}}).

Calorimeter Energy Balance
  • Qabsorbed=QCQ_{\text{absorbed}} = Q_C

  • Ensure the heat source warming the cold bath is solely the waste heat QCQ_C, never the gross heat input QHQ_H.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Apply energy conservation to the engine: QC=QH−Wout=72000 J−15120 J=56880 JQ_C = Q_H - W_{\text{out}} = 72000\text{ J} - 15120\text{ J} = 56880\text{ J}.

  2. Set the rejected heat equal to the heat gained by water: QC=mwcwΔTQ_C = m_w c_w \Delta T.

  3. Solve for the temperature change: ΔT=56880 J0.850 kg⋅4184 J/(kg⋅K)≈15.99 K\Delta T = \frac{56880\text{ J}}{0.850\text{ kg} \cdot 4184\text{ J}/(\text{kg}\cdot\text{K})} \approx 15.99\text{ K}.

  4. Compute the final temperature: Tf=T0+ΔT=293.15 K+15.99 K=309.14 K≈309.2 KT_f = T_0 + \Delta T = 293.15\text{ K} + 15.99\text{ K} = 309.14\text{ K} \approx 309.2\text{ K} (36.0∘C36.0^\circ\text{C}).

Final answer

Tf≈309.2 KT_f \approx 309.2\text{ K} (or 36.0∘C36.0^\circ\text{C})

NEXT STEPS
Final Takeaways from Your Teacher
  • Draw an energy flow (Sankey) diagram for cyclic heat engines with QHQ_H splitting into WoutW_{\text{out}} and QCQ_C.

  • Practice identifying which thermal reservoir absorbs which heat quantity in combined engine-calorimeter problems.

OverviewACEpath Teacher's Diagnosis

02 The student calculates thermal efficiency as the ratio of rejected heat to input heat rather than work to input heat.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    Pmech=τ⋅ω=0.140⋅180=25.2 W  ⟹  Wout=25.2⋅600=15120 J\mathcal{P}_{\text{mech}} = \tau \cdot \omega = 0.140 \cdot 180 = 25.2\text{ W} \implies W_{\text{out}} = 25.2 \cdot 600 = 15120\text{ J}

  2. Step 2

    Q˙C=120−25.2=94.8 W  ⟹  ηexp=Q˙CQ˙H=94.8120=0.790=79.0%\dot{Q}_C = 120 - 25.2 = 94.8\text{ W} \implies \eta_{\text{exp}} = \frac{\dot{Q}_C}{\dot{Q}_H} = \frac{94.8}{120} = 0.790 = 79.0\%

    Correct

    ηexp=PmechQ˙H=WoutQH=25.2 W120 W=0.210=21.0%\eta_{\text{exp}} = \frac{\mathcal{P}_{\text{mech}}}{\dot{Q}_H} = \frac{W_{\text{out}}}{Q_H} = \frac{25.2\text{ W}}{120\text{ W}} = 0.210 = 21.0\%

    You calculated thermal efficiency using rejected heat rate Q˙C\dot{Q}_C in the numerator instead of useful mechanical power output Pmech\mathcal{P}_{\text{mech}} (or useful work WoutW_{\text{out}}). Thermal efficiency represents what you get divided by what you pay for: η=PmechQ˙H=1−Q˙CQ˙H\eta = \frac{\mathcal{P}_{\text{mech}}}{\dot{Q}_H} = 1 - \frac{\dot{Q}_C}{\dot{Q}_H}.

  3. Step 3

    ηCarnot=1−293.15425=0.310=31.0%  ⟹  ηexp>ηCarnot\eta_{\text{Carnot}} = 1 - \frac{293.15}{425} = 0.310 = 31.0\% \implies \eta_{\text{exp}} > \eta_{\text{Carnot}}, which exceeds the Carnot limit

    Correct

    ηCarnot=1−TCTH=1−293.15 K425 K=0.310=31.0%  ⟹  ηexp<ηCarnot\eta_{\text{Carnot}} = 1 - \frac{T_C}{T_H} = 1 - \frac{293.15\text{ K}}{425\text{ K}} = 0.310 = 31.0\% \implies \eta_{\text{exp}} < \eta_{\text{Carnot}} (21.0%<31.0%21.0\% < 31.0\%)

    You calculated the Carnot efficiency accurately, but your conclusion that the engine exceeds the Carnot limit was caused by the incorrect efficiency formula used in Step 2.

  4. Step 4

    QC=94.8⋅600=56880 J  ⟹  ΔT=568800.850⋅4184=16.00 K  ⟹  Tf=293.15+16.00=309.15 KQ_C = 94.8 \cdot 600 = 56880\text{ J} \implies \Delta T = \frac{56880}{0.850 \cdot 4184} = 16.00\text{ K} \implies T_f = 293.15 + 16.00 = 309.15\text{ K}

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly computed mechanical power and work output from torque, angular speed, and time.

You applied the first law of thermodynamics correctly to determine the rejected thermal power Q˙C\dot{Q}_C.

You correctly calculated the Carnot maximum theoretical efficiency using absolute temperatures.

You set up and solved the calorimetry heat transfer equation accurately to obtain the final water temperature.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Inverted heat engine efficiency definition

none

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You confused the fraction of input heat converted into work (efficiency η=W/QH\eta = W/Q_H) with the fraction of input heat rejected to the cold reservoir (QC/QH=1−ηQ_C/Q_H = 1 - \eta).

REASONING PATH
Your ACEpath teacher’s suggested approach
Core Definition of Heat Engine Efficiency
  • For any heat engine, thermal efficiency is defined as η=useful work outputtotal heat input=WoutQH=PmechQ˙H\eta = \frac{\text{useful work output}}{\text{total heat input}} = \frac{W_{\text{out}}}{Q_H} = \frac{\mathcal{P}_{\text{mech}}}{\dot{Q}_H}.

  • Always place the net mechanical output in the numerator and the heat supplied by the hot source in the denominator.

Sanity Check with the Second Law of Thermodynamics
  • A real heat engine must always satisfy ηexp<ηCarnot<1\eta_{\text{exp}} < \eta_{\text{Carnot}} < 1.

  • If your calculated real engine efficiency exceeds the Carnot limit, pause and check whether you inverted terms or used rejected heat instead of work.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Identify the useful energy rate delivered: Pmech=25.2 W\mathcal{P}_{\text{mech}} = 25.2\text{ W}.

  2. Divide by the rate of heat supplied by the hot reservoir: ηexp=PmechQ˙H=25.2 W120 W=0.210=21.0%\eta_{\text{exp}} = \frac{\mathcal{P}_{\text{mech}}}{\dot{Q}_H} = \frac{25.2\text{ W}}{120\text{ W}} = 0.210 = 21.0\%.

  3. Compare with the theoretical Carnot limit: ηexp=21.0%<ηCarnot=31.0%\eta_{\text{exp}} = 21.0\% < \eta_{\text{Carnot}} = 31.0\%, which satisfies the Second Law of Thermodynamics for real engines.

Final answer

(a) Pmech=25.2 W\mathcal{P}_{\text{mech}} = 25.2\text{ W}, Wout=1.51×104 JW_{\text{out}} = 1.51 \times 10^4\text{ J}; (b) ηexp=0.210\eta_{\text{exp}} = 0.210 (21.0%21.0\%) compared to ηCarnot=0.310\eta_{\text{Carnot}} = 0.310 (31.0%31.0\%); (c) Tf=309.2 KT_f = 309.2\text{ K} (36.0∘C36.0^\circ\text{C})

NEXT STEPS
Final Takeaways from Your Teacher
  • Memorize the general efficiency definition: efficiency is always 'what you want' (WW) over 'what you pay for' (QHQ_H).

  • Practice rewriting the energy conservation relation η=QH−QCQH=1−QCQH\eta = \frac{Q_H - Q_C}{Q_H} = 1 - \frac{Q_C}{Q_H} so you avoid equating η\eta directly with QC/QHQ_C/Q_H.

  • Use the Carnot limit as an automatic validation check whenever solving real heat engine problems.

OverviewACEpath Teacher's Diagnosis

03 The student uses Celsius temperatures instead of absolute temperatures in Kelvin when calculating the Carnot efficiency.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    P_{mech\text{mech}} = 0.140 ⋅\cdot 180 = 25.2 W\text{ W}   ⟹  \implies W_{out\text{out}} = 25.2 ⋅\cdot 600 = 15120 J\text{ J}

  2. Step 2

    \eta_{exp\text{exp}} = 25.2120\frac{25.2}{120} = 0.210 = 21.0%_

  3. Step 3

    T_{C,C} = 293.15 - 273.15 = 20.0^\circ$$\text{C}   ⟹  \implies T_{H,C} = 425 - 273.15 = 151.85^\circ$$\text{C}   ⟹  \implies \eta_{Carnot\text{Carnot}} = 1 - 20.0151.85\frac{20.0}{151.85} = 0.868 = 86.8%_

    Correct

    \eta_{Carnot\text{Carnot}} = 1 - TCTH\frac{T_C}{T_H} = 1 - 293.15 K425 K\frac{293.15\text{ K}}{425\text{ K}} = 0.310\ (31.0%)_

    Thermodynamic efficiency formulas derived from the Second Law of Thermodynamics require absolute temperatures in Kelvin. Substituting temperatures in degrees Celsius distorts the temperature ratio TCTH\frac{T_C}{T_H} because Celsius is an offset scale rather than an absolute scale.

  4. Step 4

    \dot{Q}C = 120 - 25.2 = 94.8 W\text{ W}   ⟹  \implies Q_C = 94.8 ⋅\cdot 600 = 56880 J\text{ J}   ⟹  \implies Δ\Delta T = 568800.850⋅4184\frac{56880}{0.850 \cdot 4184} = 16.00 K\text{ K}   ⟹  \implies T_f = 293.15 + 16.00 = 309.15 K\text{ K}

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly calculated the rotational power output and total mechanical work.

You evaluated the experimental thermal efficiency accurately.

You correctly determined the heat rejected to the cold reservoir using energy conservation and solved for the final water temperature.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Temperature Scale Error in Thermodynamic Efficiency

You deliberately converted the given Kelvin temperatures to degrees Celsius before evaluating the Carnot efficiency ratio.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Treating the Carnot efficiency formula as if it accepts any temperature unit, overlooking that the ratio QCQH=TCTH\frac{Q_C}{Q_H} = \frac{T_C}{T_H} is established on the absolute thermodynamic Kelvin scale where zero corresponds to absolute zero.

REASONING PATH
Your ACEpath teacher’s suggested approach
Absolute Temperature Requirement
  • Whenever temperatures appear in ratios (such as TCTH\frac{T_C}{T_H} or the ideal gas law PV=nRTPV = nRT), absolute temperatures in Kelvin must be used.

  • Keep reservoir temperatures in Kelvin (TC=293.15 KT_C = 293.15\text{ K}, TH=425 KT_H = 425\text{ K}) and evaluate ηCarnot=1−293.15425\eta_{\text{Carnot}} = 1 - \frac{293.15}{425}.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Identify the hot and cold reservoir temperatures directly in Kelvin: TH=425 KT_H = 425\text{ K} and TC=293.15 KT_C = 293.15\text{ K}.

  2. Substitute into the Carnot efficiency formula: ηCarnot=1−TCTH=1−293.15 K425 K\eta_{\text{Carnot}} = 1 - \frac{T_C}{T_H} = 1 - \frac{293.15\text{ K}}{425\text{ K}}.

  3. Compute the ratio: 293.15425≈0.6898\frac{293.15}{425} \approx 0.6898, yielding ηCarnot=1−0.6898=0.3102\eta_{\text{Carnot}} = 1 - 0.6898 = 0.3102 (31.0%31.0\%).

Final answer

(a) Pmech=25.2 W\mathcal{P}_{\text{mech}} = 25.2\text{ W} and Wout=1.51×104 JW_{\text{out}} = 1.51 \times 10^4\text{ J}; (b) ηexp=0.210\eta_{\text{exp}} = 0.210 (21.0%21.0\%) compared to ηCarnot=0.310\eta_{\text{Carnot}} = 0.310 (31.0%31.0\%); (c) Tf=309.2 KT_f = 309.2\text{ K} (36.0∘C36.0^\circ\text{C})

NEXT STEPS
Final Takeaways from Your Teacher
  • Remember that temperature differences (ΔT\Delta T) have the same numerical value in Celsius and Kelvin, but ratios of temperatures (T1T2\frac{T_1}{T_2}) are only physically meaningful in Kelvin.

  • Review the Carnot cycle derivation to see why entropy definition dS=δQrevTdS = \frac{\delta Q_{\text{rev}}}{T} requires absolute temperature.

Lock it in

Similar question

01

A small heat engine draws 200 W200\text{ W} of heat from a thermal reservoir while producing 40 W40\text{ W} of mechanical shaft power. Its cold sink is a 0.500 kg0.500\text{ kg} block of copper (c=385 J/(kg⋅K)c = 385\text{ J}/(\text{kg}\cdot\text{K})). Calculate the rate of temperature rise dTdt\frac{dT}{dt} of the copper block assuming no heat escapes to the environment.

Answer

dTdt≈0.831 K/s\frac{dT}{dt} \approx 0.831\text{ K/s}. By conservation of energy, the rate of heat rejection is Q˙C=Q˙H−P=200 W−40 W=160 W\dot{Q}_C = \dot{Q}_H - \mathcal{P} = 200\text{ W} - 40\text{ W} = 160\text{ W}. Then dTdt=Q˙Cmc=160 W0.500 kg⋅385 J/(kg⋅K)≈0.831 K/s\frac{dT}{dt} = \frac{\dot{Q}_C}{m c} = \frac{160\text{ W}}{0.500\text{ kg} \cdot 385\text{ J}/(\text{kg}\cdot\text{K})} \approx 0.831\text{ K/s}.

02

An experimental Carnot engine operates between TH=500 KT_H = 500\text{ K} and TC=300 KT_C = 300\text{ K}. It consumes 45.0 kJ45.0\text{ kJ} of heat from the hot source. If the rejected heat is directed into an insulated container holding 2.00 kg2.00\text{ kg} of water (cw=4184 J/(kg⋅K)c_w = 4184\text{ J}/(\text{kg}\cdot\text{K})) initially at 20.0∘C20.0^\circ\text{C}, find the final water temperature TfT_f.

Answer

Tf≈23.2∘CT_f \approx 23.2^\circ\text{C} (296.4 K296.4\text{ K}). Carnot efficiency is η=1−300500=0.400\eta = 1 - \frac{300}{500} = 0.400. Work done is W=0.400×45.0 kJ=18.0 kJW = 0.400 \times 45.0\text{ kJ} = 18.0\text{ kJ}. Rejected heat is QC=QH−W=27.0 kJ=27000 JQ_C = Q_H - W = 27.0\text{ kJ} = 27000\text{ J}. Temperature rise is ΔT=27000 J2.00 kg⋅4184 J/(kg⋅K)≈3.23 K\Delta T = \frac{27000\text{ J}}{2.00\text{ kg} \cdot 4184\text{ J}/(\text{kg}\cdot\text{K})} \approx 3.23\text{ K}, giving Tf=20.0∘C+3.23∘C≈23.2∘CT_f = 20.0^\circ\text{C} + 3.23^\circ\text{C} \approx 23.2^\circ\text{C}.

03

A Stirling engine with an efficiency of η=0.25\eta = 0.25 drives a generator with electrical efficiency ηgen=0.80\eta_{\text{gen}} = 0.80, delivering 120 W120\text{ W} of electric power. The waste heat from the engine's cold side is cooled by circulating water flowing through an absorber at a mass flow rate of m˙=0.025 kg/s\dot{m} = 0.025\text{ kg/s} (cw=4184 J/(kg⋅K)c_w = 4184\text{ J}/(\text{kg}\cdot\text{K})). Find the steady-state temperature increase ΔT\Delta T of the cooling water.

Answer

ΔT≈4.30 K\Delta T \approx 4.30\text{ K}. Mechanical power required is Pmech=120 W0.80=150 W\mathcal{P}_{\text{mech}} = \frac{120\text{ W}}{0.80} = 150\text{ W}. Total thermal input rate is Q˙H=Pmechη=150 W0.25=600 W\dot{Q}_H = \frac{\mathcal{P}_{\text{mech}}}{\eta} = \frac{150\text{ W}}{0.25} = 600\text{ W}. Rate of waste heat rejected is Q˙C=Q˙H−Pmech=600 W−150 W=450 W\dot{Q}_C = \dot{Q}_H - \mathcal{P}_{\text{mech}} = 600\text{ W} - 150\text{ W} = 450\text{ W}. Temperature rise is ΔT=Q˙Cm˙cw=450 W0.025 kg/s⋅4184 J/(kg⋅K)≈4.30 K\Delta T = \frac{\dot{Q}_C}{\dot{m} c_w} = \frac{450\text{ W}}{0.025\text{ kg/s} \cdot 4184\text{ J}/(\text{kg}\cdot\text{K})} \approx 4.30\text{ K}.

Loading workspace…