Resources
A solid uniform circular disk of radius and mass has a moment of inertia of . A concentric circular hole of radius is bored out of the center, leaving a flat annular ring of the same total mass and outer radius . The moment of inertia of the annular ring about its central perpendicular axis is given by . Determine the threshold inner radius such that the moment of inertia increases by exactly compared to the solid disk of equal mass.
Answer and steps
Final answer
Steps
Express the condition relating the two moments of inertia
The moment of inertia of the solid disk about its central axis is:
The moment of inertia of the annular ring with the same total mass () is:
We are given that increases by relative to :
Set up and simplify the algebraic equation
Substitute the formulas for and into the condition:
Divide both sides by :
Subtract from both sides:
Solve for the inner radius
Take the square root of both sides (since a radius must be positive):
Substitute the given value :
Common Pitfall: Do not confuse keeping the total mass constant with keeping the density constant. If material were simply removed from the original disk without replacing it, the mass would decrease. Here, the annular ring has the same total mass , meaning mass has been redistributed farther away from the axis of rotation, which increases the rotational inertia.
Typical errors
01 The student forgets to take the square root of 0.250 when solving for r from r² = 0.250 R₀², resulting in r_crit = 0.100 m.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2
- Step 3Correct
You equated directly to the value of rather than taking the square root of .
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly identified and applied the moment of inertia formulas for both the solid disk and the annular ring.
You translated the percentage increase into the correct factor of .
You executed all algebraic steps leading up to without error.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou stopped at and assigned its numeric value directly to , missing the final square root operation.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisCognitive overload at the final step caused you to treat the squared variable as the linear variable , conflating with .
REASONING PATH
Your ACEpath teacher’s suggested approach- Check variable power and units
If the expression on the left-hand side is , its unit is , which cannot directly equal a linear radius in meters.
Before writing down your final answer, verify that you have isolated , not , by taking the square root: .
CORRECTED PATH
ACEpath Teacher's DemonstrationTake the principal square root of both sides:
Evaluate the numerical square root:
02 The student misinterprets the 25.0% increase as meaning the inner radius r is 25.0% of the outer radius R₀, rather than relating the moments of inertia.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
The problem states that the moment of inertia increases by , not that the inner radius is of the outer radius. You need to write the condition as using the provided rotational inertia formulas.
- Step 2Correct
You correctly substituted into your assumed linear relation, but the value is incorrect due to the conceptual error in Step 1.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly identified that the percentage increase given in the problem statement is .
You substituted the given outer radius into your formula accurately.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou equated a percentage change in moment of inertia directly to a linear fraction of the geometric radius, bypassing the defining rotational inertia formulas and where mass distribution depends on .
REASONING PATH
Your ACEpath teacher’s suggested approach- Relate percentage changes to physical quantities
A percentage change in a physical quantity means , not that a length dimension scales by that percentage.
Write before expressing in terms of geometric dimensions.
- Account for quadratic radius dependence
Because , the fractional increase equals .
Take the square root of the fractional change to find the ratio .
CORRECTED PATH
ACEpath Teacher's DemonstrationSet up the fractional increase condition: .
Substitute the expressions: .
Solve for : .
Compute numerical value: .
03 The student incorrectly uses a difference formula (R₀² - r²) for the annular ring's moment of inertia instead of the given sum formula (R₀² + r²), leading to an impossible condition.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
You used a difference of squares rather than the sum of squares given in the problem statement. When mass is held constant while boring out the center, mass is shifted farther from the rotational axis, which increases the moment of inertia.
- Step 2Correct
Your algebraic simplification was carried out correctly from your equation, but it inherited the sign error from Step 1, resulting in .
- Step 3Correct
You arrived at by dropping the negative sign in . In real numbers, has no real solution, which signals that the initial equation had an error.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly interpreted that a increase corresponds to .
You correctly recognized that both objects share the same total mass and outer radius .
You carried out the algebraic cancellation of cleanly.
THE ERROR
Where Your ACEpath Teacher Spotted the Mistakeno
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou confused the formula for the area of an annulus or the subtraction of removed mass with the moment of inertia of a fixed-mass annular ring. In moment of inertia formulas expressed in terms of fixed total mass, the inner and outer radii add () because removing inner mass and redistributing it outward moves mass farther from the rotation axis.
REASONING PATH
Your ACEpath teacher’s suggested approach- Fixed Mass vs. Fixed Density
When a hollow cylinder or annular ring has a fixed total mass , its moment of inertia is , not .
Check whether the problem specifies constant total mass or constant density before writing down the moment of inertia formula.
- Real-Value Feasibility Check
A squared physical dimension such as must always be non-negative in classical mechanics.
If an algebraic step yields , immediately pause and inspect earlier steps for a sign error rather than discarding the minus sign.
CORRECTED PATH
ACEpath Teacher's DemonstrationWrite the given moment of inertia for the annular ring of fixed mass : .
Set up the ratio: .
Cancel common factors: .
Take the square root: .
Lock it in
When an algebraic equation simplifies to , what final operation is required to obtain the radius ?
Take the positive square root: . Remember that represents an area-like dimension, not a linear radius.
Similar question
A solid cylinder of mass and radius has moment of inertia . A concentric core of radius is hollowed out, maintaining the same total mass , such that . Find the inner radius .
Answer
. Setting yields . Taking the square root gives .
A thin spherical shell of mass and radius has . A thick spherical shell of the same mass and outer radius has moment of inertia . If an annular flat disk of equal mass and outer radius satisfies , calculate its inner radius .
Answer
. Taking the square root of both sides gives . Substituting yields .
A flywheel is modeled as an annular disk of outer radius and inner radius . To achieve a moment of inertia that is times that of a solid disk of identical mass and outer radius, what must be the ratio , and what is the value of ?
Answer
, . From , we get . Taking the square root yields , so .