Resources

Two identical parallel-plate capacitors, Capacitor 1 and Capacitor 2, each initially have capacitance C0=150 pFC_0 = 150\text{ pF} and are charged to an identical potential difference ΔV0=80.0 V\Delta V_0 = 80.0\text{ V}. Both capacitors then have their charging supplies removed, leaving them electrically isolated. Next, a dielectric slab of dielectric constant κ=4.00\kappa = 4.00 is completely inserted into Capacitor 1. In contrast, for Capacitor 2, the plate separation is doubled from d0d_0 to 2d02d_0 without inserting any dielectric. Counter to naive intuition that modifying capacitor geometry or filling always affects stored energy in the same direction, compare the energetic outcomes: calculate the factor by which the stored electrostatic energy changes, UfUi\frac{U_f}{U_i}, for (a) Capacitor 1, and (b) Capacitor 2; then (c) state the final stored energy Uf,1U_{f,1} in microjoules (μJ\mu\text{J}) and Uf,2U_{f,2} in microjoules (μJ\mu\text{J}).

Answer and steps

Final answer

(a) Uf,1Ui,1=0.250\frac{U_{f,1}}{U_{i,1}} = 0.250; (b) Uf,2Ui,2=2.00\frac{U_{f,2}}{U_{i,2}} = 2.00; (c) Uf,1=0.120 μJU_{f,1} = 0.120\text{ }\mu\text{J} and Uf,2=0.960 μJU_{f,2} = 0.960\text{ }\mu\text{J}

Steps

01

Key Principle for Isolated Capacitors

When a capacitor is charged to a potential difference ΔV0\Delta V_0 and then disconnected from its voltage source, it becomes electrically isolated. Because there is no closed conductive path for electrons to flow to or from the plates, the net charge Q0Q_0 on the plates remains constant:

Q0=C0ΔV0Q_0 = C_0 \Delta V_0

The initial electrostatic energy stored in each capacitor is:

Ui=12C0(ΔV0)2=Q022C0U_i = \frac{1}{2} C_0 (\Delta V_0)^2 = \frac{Q_0^2}{2C_0}

Substituting the given values:

Ui=12(150×10−12 F)(80.0 V)2=12(150×10−12 F)(6400 V2)=4.80×10−7 J=0.480 μJU_i = \frac{1}{2} (150 \times 10^{-12}\text{ F}) (80.0\text{ V})^2 = \frac{1}{2} (150 \times 10^{-12}\text{ F}) (6400\text{ V}^2) = 4.80 \times 10^{-7}\text{ J} = 0.480\text{ }\mu\text{J}

Common Pitfall: Do not use U=12C(ΔV)2U = \frac{1}{2}C(\Delta V)^2 assuming ΔV\Delta V stays constant. Because the voltage source is disconnected, the potential difference ΔV=Q0C\Delta V = \frac{Q_0}{C} varies inversely with capacitance. Using U=Q022CU = \frac{Q_0^2}{2C} directly captures the constant-charge condition:

UfUi=Q02/(2Cf)Q02/(2Ci)=CiCf\frac{U_f}{U_i} = \frac{Q_0^2 / (2C_f)}{Q_0^2 / (2C_i)} = \frac{C_i}{C_f}


02

Part (a): Energy Change for Capacitor 1 (Dielectric Insertion)

The capacitance of a parallel-plate capacitor filled with a dielectric of constant κ\kappa is:

Cf,1=κC0C_{f,1} = \kappa C_0

With κ=4.00\kappa = 4.00:

Cf,1=4.00C0C_{f,1} = 4.00 C_0

The energy ratio is therefore:

Uf,1Ui,1=C0Cf,1=C04.00C0=14.00=0.250\frac{U_{f,1}}{U_{i,1}} = \frac{C_0}{C_{f,1}} = \frac{C_0}{4.00 C_0} = \frac{1}{4.00} = 0.250


03

Part (b): Energy Change for Capacitor 2 (Plate Separation Doubled)

The capacitance of an air-filled parallel-plate capacitor of plate area AA and separation dd is given by C=ε0AdC = \frac{\varepsilon_0 A}{d}. Doubling the plate separation from d0d_0 to 2d02d_0 halves the capacitance:

Cf,2=ε0A2d0=C02=0.500C0C_{f,2} = \frac{\varepsilon_0 A}{2d_0} = \frac{C_0}{2} = 0.500 C_0

The energy ratio is:

Uf,2Ui,2=C0Cf,2=C00.500C0=2.00\frac{U_{f,2}}{U_{i,2}} = \frac{C_0}{C_{f,2}} = \frac{C_0}{0.500 C_0} = 2.00

(Physically, external mechanical work is performed to pull the oppositely charged plates apart against their mutual electrostatic attraction, increasing the stored energy.)


04

Part (c): Final Stored Energies

Using the ratios found above and the initial energy Ui=0.480 μJU_i = 0.480\text{ }\mu\text{J}:

  • For Capacitor 1: Uf,1=0.250×0.480 μJ=0.120 μJU_{f,1} = 0.250 \times 0.480\text{ }\mu\text{J} = 0.120\text{ }\mu\text{J}
  • For Capacitor 2: Uf,2=2.00×0.480 μJ=0.960 μJU_{f,2} = 2.00 \times 0.480\text{ }\mu\text{J} = 0.960\text{ }\mu\text{J}

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student mistakenly assumes potential difference remains constant instead of charge being conserved on an isolated capacitor, using U = (1/2)C(ΔV)² to find energy ratios directly proportional to capacitance.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    C1=κC0=4.00C0C_1 = \kappa C_0 = 4.00 C_0

  2. Step 2

    U=12C(ΔV)2 with constant ΔV  ⟹  UfUi=C1C0=4.00U = \frac{1}{2} C (\Delta V)^2 \text{ with constant } \Delta V \implies \frac{U_f}{U_i} = \frac{C_1}{C_0} = 4.00

    Correct

    Uf,1Ui,1=Q02/(2Cf,1)Q02/(2C0)=C0Cf,1=14.00=0.250\frac{U_{f,1}}{U_{i,1}} = \frac{Q_0^2 / (2C_{f,1})}{Q_0^2 / (2C_0)} = \frac{C_0}{C_{f,1}} = \frac{1}{4.00} = 0.250

    Because the battery is disconnected, charge QQ is trapped on the plates and remains constant while ΔV\Delta V changes. Expressing energy as U=Q22CU = \frac{Q^2}{2C} reveals that stored energy is inversely proportional to capacitance.

  3. Step 3

    C2=ε0A2d0=C02=0.500C0C_2 = \frac{\varepsilon_0 A}{2d_0} = \frac{C_0}{2} = 0.500 C_0

  4. Step 4

    UfUi=C2C0=0.500\frac{U_f}{U_i} = \frac{C_2}{C_0} = 0.500

    Correct

    Uf,2Ui,2=C0Cf,2=C00.500C0=2.00\frac{U_{f,2}}{U_{i,2}} = \frac{C_0}{C_{f,2}} = \frac{C_0}{0.500 C_0} = 2.00

    Following the constant-charge condition, the energy ratio is C0Cf,2=10.500=2.00\frac{C_0}{C_{f,2}} = \frac{1}{0.500} = 2.00 rather than being directly proportional to CC.

  5. Step 5

    Ui=12C0(ΔV0)2=0.5×(150×10−12 F)×(80.0 V)2=0.480 μJU_i = \frac{1}{2} C_0 (\Delta V_0)^2 = 0.5 \times (150 \times 10^{-12}\text{ F}) \times (80.0\text{ V})^2 = 0.480\text{ }\mu\text{J}

  6. Step 6

    U(f,1)=4.00×0.480 μJ=1.92 μJ  ⟹  U(f,2)=0.500×0.480 μJ=0.240 μJU_{(f,1)} = 4.00 \times 0.480\text{ }\mu\text{J} = 1.92\text{ }\mu\text{J} \implies U_{(f,2)} = 0.500 \times 0.480\text{ }\mu\text{J} = 0.240\text{ }\mu\text{J}

    Correct

    Uf,1=0.250×0.480 μJ=0.120 μJ  ⟹  Uf,2=2.00×0.480 μJ=0.960 μJU_{f,1} = 0.250 \times 0.480\text{ }\mu\text{J} = 0.120\text{ }\mu\text{J} \implies U_{f,2} = 2.00 \times 0.480\text{ }\mu\text{J} = 0.960\text{ }\mu\text{J}

    Your arithmetic was accurate, but multiplying by the inverted energy ratios led to incorrect final energy values.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly calculated the modified capacitance for both the dielectric insertion and the doubled plate spacing.

You correctly determined the initial electrostatic energy Ui=0.480 μJU_i = 0.480\text{ }\mu\text{J} from the given initial parameters.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Constant Voltage vs. Constant Charge Confusion

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You assumed potential difference ΔV\Delta V remains fixed during geometric or dielectric modifications, even though the capacitors were electrically isolated from their voltage source. Disconnection removes any path for charge transfer, making plate charge QQ the invariant quantity, which implies U=Q22CU = \frac{Q^2}{2C} and U∝1CU \propto \frac{1}{C}.

REASONING PATH
Your ACEpath teacher’s suggested approach
Circuit Connectivity Status
  • Connected to battery   ⟹  ΔV=constant\implies \Delta V = \text{constant}; Disconnected / isolated   ⟹  Q=constant\implies Q = \text{constant}.

  • Always check whether a battery remains connected before choosing between U=12C(ΔV)2U = \frac{1}{2}C(\Delta V)^2 and U=Q22CU = \frac{Q^2}{2C}.

Energy Ratio for Isolated Capacitors
  • For constant QQ, U=Q22C  ⟹  UfUi=CiCfU = \frac{Q^2}{2C} \implies \frac{U_f}{U_i} = \frac{C_i}{C_f}.

  • Invert the capacitance ratio when finding the energy ratio of an isolated capacitor.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. For an isolated capacitor, QQ is constant, so UfUi=C0Cf\frac{U_f}{U_i} = \frac{C_0}{C_f}.

  2. For Capacitor 1: Uf,1Ui,1=C04.00C0=0.250\frac{U_{f,1}}{U_{i,1}} = \frac{C_0}{4.00 C_0} = 0.250.

  3. For Capacitor 2: Uf,2Ui,2=C00.500C0=2.00\frac{U_{f,2}}{U_{i,2}} = \frac{C_0}{0.500 C_0} = 2.00.

  4. Calculate final energies: Uf,1=0.250×0.480 μJ=0.120 μJU_{f,1} = 0.250 \times 0.480\text{ }\mu\text{J} = 0.120\text{ }\mu\text{J} and Uf,2=2.00×0.480 μJ=0.960 μJU_{f,2} = 2.00 \times 0.480\text{ }\mu\text{J} = 0.960\text{ }\mu\text{J}.

Final answer

(a) Uf,1Ui,1=0.250\frac{U_{f,1}}{U_{i,1}} = 0.250; (b) Uf,2Ui,2=2.00\frac{U_{f,2}}{U_{i,2}} = 2.00; (c) Uf,1=0.120 μJU_{f,1} = 0.120\text{ }\mu\text{J} and Uf,2=0.960 μJU_{f,2} = 0.960\text{ }\mu\text{J}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the distinction between constant-voltage systems (battery connected) and constant-charge systems (battery disconnected).

  • Practice matching the energy formula variant (U=12C(ΔV)2U = \frac{1}{2}C(\Delta V)^2, U=Q22CU = \frac{Q^2}{2C}, or U=12QΔVU = \frac{1}{2}Q\Delta V) to the physical quantity held fixed in the scenario.

OverviewACEpath Teacher's Diagnosis

02 The student misremembers the capacitance formula as directly proportional to plate separation d, concluding that doubling the separation doubles the capacitance.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    Q is constant since the capacitor is isolated  ⟹  C1=κC0=4.00C0  ⟹  U=Q22C  ⟹  UfUi=C0C1=14.00=0.250Q\text{ is constant since the capacitor is isolated} \implies C_1 = \kappa C_0 = 4.00 C_0 \implies U = \frac{Q^2}{2C} \implies \frac{U_f}{U_i} = \frac{C_0}{C_1} = \frac{1}{4.00} = 0.250

  2. Step 2

    C is proportional to d, so C2=2C0  ⟹  Q is constant  ⟹  UfUi=C0C2=12=0.500C\text{ is proportional to }d\text{, so }C_2 = 2C_0 \implies Q\text{ is constant} \implies \frac{U_f}{U_i} = \frac{C_0}{C_2} = \frac{1}{2} = 0.500

    Correct

    C=ε0Ad∝1d  ⟹  Cf,2=C02=0.500C0  ⟹  Uf,2Ui,2=C0Cf,2=C00.500C0=2.00C = \frac{\varepsilon_0 A}{d} \propto \frac{1}{d} \implies C_{f,2} = \frac{C_0}{2} = 0.500 C_0 \implies \frac{U_{f,2}}{U_{i,2}} = \frac{C_0}{C_{f,2}} = \frac{C_0}{0.500 C_0} = 2.00

    For a parallel-plate capacitor, capacitance is inversely proportional to plate separation (C=ε0AdC = \frac{\varepsilon_0 A}{d}). Doubling the distance dd halves the capacitance to Cf,2=0.500C0C_{f,2} = 0.500 C_0, so the energy ratio is C0Cf,2=2.00\frac{C_0}{C_{f,2}} = 2.00.

  3. Step 3

    Ui=12C0(ΔV0)2=0.5×(150×10−12 F)×(80.0 V)2=0.480 μJ  ⟹  U(f,1)=0.250×0.480 μJ=0.120 μJ  ⟹  U(f,2)=0.500×0.480 μJ=0.240 μJU_i = \frac{1}{2} C_0 (\Delta V_0)^2 = 0.5 \times (150 \times 10^{-12}\text{ F}) \times (80.0\text{ V})^2 = 0.480\text{ }\mu\text{J} \implies U_{(f,1)} = 0.250 \times 0.480\text{ }\mu\text{J} = 0.120\text{ }\mu\text{J} \implies U_{(f,2)} = 0.500 \times 0.480\text{ }\mu\text{J} = 0.240\text{ }\mu\text{J}

    Correct

    Ui=0.480 μJ  ⟹  Uf,1=0.250×0.480 μJ=0.120 μJ  ⟹  Uf,2=2.00×0.480 μJ=0.960 μJU_i = 0.480\text{ }\mu\text{J} \implies U_{f,1} = 0.250 \times 0.480\text{ }\mu\text{J} = 0.120\text{ }\mu\text{J} \implies U_{f,2} = 2.00 \times 0.480\text{ }\mu\text{J} = 0.960\text{ }\mu\text{J}

    You calculated the initial energy UiU_i and Uf,1U_{f,1} correctly. Your calculation for Uf,2U_{f,2} executed the arithmetic accurately, but it inherited the incorrect ratio of 0.5000.500 from part (b).

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified that disconnecting the battery keeps the charge QQ fixed on both capacitors.

You correctly selected the energy expression U=Q22CU = \frac{Q^2}{2C} for isolated systems.

You accurately determined the dielectric scaling C1=κC0C_1 = \kappa C_0 and the resulting energy ratio for Capacitor 1.

You computed the initial stored energy Ui=0.480 μJU_i = 0.480\text{ }\mu\text{J} with correct unit conversions.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Capacitance Geometry Relation Inversion

You wrote that capacitance CC is proportional to plate separation dd instead of being inversely proportional to dd.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You confused the geometric dependence of parallel-plate capacitance C=ε0AdC = \frac{\varepsilon_0 A}{d} with direct proportionality, forgetting that bringing plates closer together increases charge storage capacity at a given potential difference, while pulling them farther apart decreases it.

REASONING PATH
Your ACEpath teacher’s suggested approach
Parallel-Plate Capacitance Formula
  • C=κε0AdC = \frac{\kappa \varepsilon_0 A}{d}, where AA is plate area and dd is plate separation.

  • Always verify that separation dd is in the denominator: increasing distance decreases capacitance.

Physical Work Check for Isolated Plates
  • Oppositely charged plates attract each other, so pulling them apart requires positive external mechanical work (Wext>0W_{\text{ext}} > 0).

  • Check the sign of energy change: pulling isolated plates apart must increase stored electrostatic energy (Uf>UiU_f > U_i).

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Use the geometric relation C=ε0AdC = \frac{\varepsilon_0 A}{d} to find the new capacitance when d→2d0d \to 2d_0: Cf,2=ε0A2d0=C02=0.500C0C_{f,2} = \frac{\varepsilon_0 A}{2d_0} = \frac{C_0}{2} = 0.500 C_0.

  2. For constant charge QQ, express the energy ratio as Uf,2Ui,2=C0Cf,2=C00.500C0=2.00\frac{U_{f,2}}{U_{i,2}} = \frac{C_0}{C_{f,2}} = \frac{C_0}{0.500 C_0} = 2.00.

  3. Multiply this ratio by Ui=0.480 μJU_i = 0.480\text{ }\mu\text{J} to find the final stored energy: Uf,2=2.00×0.480 μJ=0.960 μJU_{f,2} = 2.00 \times 0.480\text{ }\mu\text{J} = 0.960\text{ }\mu\text{J}.

Final answer

(a) Uf,1Ui,1=0.250\frac{U_{f,1}}{U_{i,1}} = 0.250; (b) Uf,2Ui,2=2.00\frac{U_{f,2}}{U_{i,2}} = 2.00; (c) Uf,1=0.120 μJU_{f,1} = 0.120\text{ }\mu\text{J} and Uf,2=0.960 μJU_{f,2} = 0.960\text{ }\mu\text{J}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the geometric formula C=ε0AdC = \frac{\varepsilon_0 A}{d} and practice associating smaller plate separation with greater charge concentration and higher capacitance.

  • Use physical intuition (work done against attractive electric forces) to sanity-check whether stored energy should increase or decrease when manipulating isolated capacitor plates.

OverviewACEpath Teacher's Diagnosis

03 The student assumes that inserting a dielectric decreases capacitance by dividing by κ instead of multiplying, leading to an inverted capacitance and energy ratio for Capacitor 1.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    C1=C0κ=C04.00=0.250 C0  ⟹  UfUi=C0C1=4.00C_1 = \frac{C_0}{\kappa} = \frac{C_0}{4.00} = 0.250\,C_0 \implies \frac{U_f}{U_i} = \frac{C_0}{C_1} = 4.00

    Correct

    Cf,1=κC0=4.00 C0  ⟹  Uf,1Ui,1=C0Cf,1=14.00=0.250C_{f,1} = \kappa C_0 = 4.00\,C_0 \implies \frac{U_{f,1}}{U_{i,1}} = \frac{C_0}{C_{f,1}} = \frac{1}{4.00} = 0.250

    Inserting a dielectric always increases the capacitance by a factor of κ\kappa (C=κC0C = \kappa C_0, where κ≥1\kappa \ge 1). You divided by κ\kappa instead of multiplying, resulting in an inverted capacitance and an incorrect energy ratio.

  2. Step 2

    C2=ε0A2d0=0.500 C0  ⟹  UfUi=C0C2=2.00C_2 = \frac{\varepsilon_0 A}{2d_0} = 0.500\,C_0 \implies \frac{U_f}{U_i} = \frac{C_0}{C_2} = 2.00

  3. Step 3

    Ui=12C0(ΔV0)2=0.5×(150×10−12 F)×(80.0 V)2=0.480 μJU_i = \frac{1}{2} C_0 (\Delta V_0)^2 = 0.5 \times (150 \times 10^{-12}\text{ F}) \times (80.0\text{ V})^2 = 0.480\text{ }\mu\text{J}

  4. Step 4

    U(f,1)=4.00×0.480 μJ=1.92 μJ  ⟹  U(f,2)=2.00×0.480 μJ=0.960 μJU_{(f,1)} = 4.00 \times 0.480\text{ }\mu\text{J} = 1.92\text{ }\mu\text{J} \implies U_{(f,2)} = 2.00 \times 0.480\text{ }\mu\text{J} = 0.960\text{ }\mu\text{J}

    Correct

    Uf,1=0.250×0.480 μJ=0.120 μJ  ⟹  Uf,2=2.00×0.480 μJ=0.960 μJU_{f,1} = 0.250 \times 0.480\text{ }\mu\text{J} = 0.120\text{ }\mu\text{J} \implies U_{f,2} = 2.00 \times 0.480\text{ }\mu\text{J} = 0.960\text{ }\mu\text{J}

    Your calculation for Uf,2U_{f,2} is completely correct. Your value for Uf,1U_{f,1} is numerically consistent with your ratio from Step 1, but it inherited the earlier error where C1C_1 was divided by κ\kappa.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly recognized that disconnecting the voltage supply isolates the plates, keeping the charge QQ constant.

You selected the ideal energy formula U=Q22CU = \frac{Q^2}{2C} for isolated systems.

You accurately determined the effect of doubling the plate separation on both capacitance and stored energy in Capacitor 2.

You computed the initial stored energy Ui=0.480 μJU_i = 0.480\text{ }\mu\text{J} without any algebraic or unit conversion mistakes.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Dielectric Constant Multiplier Inversion

Dividing capacitance by κ\kappa rather than multiplying by κ\kappa when adding a dielectric.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You likely conflated the electric field reduction (E=E0κE = \frac{E_0}{\kappa}) and potential difference reduction (ΔV=ΔV0κ\Delta V = \frac{\Delta V_0}{\kappa}) inside an isolated capacitor with the definition of capacitance itself. While electric field and potential decrease upon inserting a dielectric, the capacitance always increases because C=κC0C = \kappa C_0.

REASONING PATH
Your ACEpath teacher’s suggested approach
Capacitance with a Dielectric
  • Inserting a dielectric slab with dielectric constant κ>1\kappa > 1 into a capacitor always increases its capacitance: C=κC0C = \kappa C_0.

  • Check whether your resulting capacitance is larger than the vacuum value; it must never decrease when adding a dielectric material.

Energy of an Isolated System
  • For an isolated capacitor (Q=constantQ = \text{constant}), U=Q22CU = \frac{Q^2}{2C}, meaning stored energy is inversely proportional to capacitance: UfUi=CiCf\frac{U_f}{U_i} = \frac{C_i}{C_f}.

  • Because inserting a dielectric increases capacitance (Cf>CiC_f > C_i), the stored electrostatic energy must decrease (UfUi=1κ<1\frac{U_f}{U_i} = \frac{1}{\kappa} < 1).

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Apply the correct dielectric relationship: Cf,1=κC0=4.00C0C_{f,1} = \kappa C_0 = 4.00 C_0.

  2. Evaluate the energy ratio under constant charge: Uf,1Ui,1=C0Cf,1=14.00=0.250\frac{U_{f,1}}{U_{i,1}} = \frac{C_0}{C_{f,1}} = \frac{1}{4.00} = 0.250.

  3. Calculate the final stored energy: Uf,1=0.250×0.480 μJ=0.120 μJU_{f,1} = 0.250 \times 0.480\text{ }\mu\text{J} = 0.120\text{ }\mu\text{J}.

Final answer

(a) Uf,1Ui,1=0.250\frac{U_{f,1}}{U_{i,1}} = 0.250; (b) Uf,2Ui,2=2.00\frac{U_{f,2}}{U_{i,2}} = 2.00; (c) Uf,1=0.120 μJU_{f,1} = 0.120\text{ }\mu\text{J} and Uf,2=0.960 μJU_{f,2} = 0.960\text{ }\mu\text{J}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the microscopic mechanism of dielectrics: induced dipole alignment weakens the internal electric field and allows the capacitor to store more charge per volt (C=κC0C = \kappa C_0).

  • Practice distinguishing which quantities decrease (electric field EE, voltage ΔV\Delta V, stored energy UU) versus which quantity increases (capacitance CC) when a dielectric enters an isolated capacitor.

Lock it in

Similar question

01

A parallel-plate capacitor is charged to 50.0 V50.0\text{ V} and then disconnected from the power supply. A dielectric sheet with κ=2.50\kappa = 2.50 is subsequently inserted between the plates. If the initial stored energy was 200 μJ200\text{ }\mu\text{J}, determine the factor UfUi\frac{U_f}{U_i} and the final stored energy UfU_f.

Answer

Since the capacitor is isolated, QQ is constant. The new capacitance is Cf=κCi=2.50CiC_f = \kappa C_i = 2.50 C_i. The energy ratio is UfUi=CiCf=12.50=0.400\frac{U_f}{U_i} = \frac{C_i}{C_f} = \frac{1}{2.50} = 0.400. The final energy is Uf=0.400×200 μJ=80.0 μJU_f = 0.400 \times 200\text{ }\mu\text{J} = 80.0\text{ }\mu\text{J}.

02

An air-filled parallel-plate capacitor with capacitance 80.0 pF80.0\text{ pF} is charged to 120 V120\text{ V} and disconnected. The plates are initially separated by 1.20 mm1.20\text{ mm}. If an external agent pulls the plates apart to a new separation of 3.60 mm3.60\text{ mm}, how much mechanical work WextW_{\text{ext}} was performed on the system?

Answer

Initial energy: Ui=12C0(ΔV0)2=12(80.0×10−12 F)(120 V)2=5.76 μJU_i = \frac{1}{2} C_0 (\Delta V_0)^2 = \frac{1}{2} (80.0 \times 10^{-12}\text{ F}) (120\text{ V})^2 = 5.76\text{ }\mu\text{J}. With separation tripled, capacitance becomes Cf=C03C_f = \frac{C_0}{3}. For constant QQ, Uf=3Ui=17.28 μJU_f = 3 U_i = 17.28\text{ }\mu\text{J}. By conservation of energy, Wext=Uf−Ui=17.28 μJ−5.76 μJ=11.52 μJW_{\text{ext}} = U_f - U_i = 17.28\text{ }\mu\text{J} - 5.76\text{ }\mu\text{J} = 11.52\text{ }\mu\text{J}.

03

Contrast two identical capacitors, A and B, each with initial capacitance C0C_0 and stored energy U0U_0. Both have a dielectric slab of κ=3.0\kappa = 3.0 inserted, but Capacitor A remains connected to a constant voltage battery, while Capacitor B is disconnected before insertion. Find the final energy ratio UfU0\frac{U_f}{U_0} for each capacitor, and explain the physical reason for the difference.

Answer

For Capacitor A (battery connected, ΔV\Delta V constant): U=12C(ΔV)2U = \frac{1}{2} C (\Delta V)^2, so Uf,AU0=CfC0=κ=3.00\frac{U_{f,A}}{U_0} = \frac{C_f}{C_0} = \kappa = 3.00 (the battery supplies additional charge and energy). For Capacitor B (isolated, QQ constant): U=Q22CU = \frac{Q^2}{2C}, so Uf,BU0=C0Cf=1κ=13.00≈0.333\frac{U_{f,B}}{U_0} = \frac{C_0}{C_f} = \frac{1}{\kappa} = \frac{1}{3.00} \approx 0.333 (the dielectric is attracted into the plates, doing work and reducing stored electrostatic field energy).

Loading workspace…