Resources

A hydraulic system filled with oil of density ρ=860 kg/m3\rho = 860\text{ kg/m}^3 consists of a narrow piston of cross-sectional area A1=8.00 cm2A_1 = 8.00\text{ cm}^2 and a wider load piston of cross-sectional area A2=200 cm2A_2 = 200\text{ cm}^2. When an input force of F1=110 NF_1 = 110\text{ N} is applied downward on the narrow piston, the load piston rises until the system reaches a static threshold where the top surface of the load piston platform rests at an elevation of h=1.45 mh = 1.45\text{ m} higher than the top surface of the input piston. Taking g=9.80 m/s2g = 9.80\text{ m/s}^2, determine the maximum total load force F2F_2 that can be supported on the output piston at this exact height threshold.

Answer and steps

Final answer

F2=2500 NF_2 = 2500\text{ N}

Steps

01

Identify the Pressure at the Reference Level

To find the load force F2F_2, we apply the principle of hydrostatic equilibrium connecting the pressure at the two pistons.

In a continuous, static fluid, points at the same vertical height experience the same total pressure. Choose the horizontal plane passing through the base of the lower input piston (piston 1) as our reference level.

  • Pressure at the input piston:
    The pressure exerted just below piston 1 is the atmospheric pressure plus the pressure from the applied downward force F1F_1: P1=Patm+F1A1P_1 = P_{\text{atm}} + \frac{F_1}{A_1}
  • Pressure at the same elevation below the load piston:
    Piston 2 rests at an elevation hh above the reference level. Therefore, the pressure at the reference level in the wider column is the pressure directly beneath piston 2 plus the hydrostatic pressure of the oil column of height hh: Pref=P2+ρgh=(Patm+F2A2)+ρghP_{\text{ref}} = P_2 + \rho g h = \left(P_{\text{atm}} + \frac{F_2}{A_2}\right) + \rho g h
02

Equate the Pressures at the Reference Level

Since the fluid is in static equilibrium: P1=PrefP_1 = P_{\text{ref}}

Patm+F1A1=Patm+F2A2+ρghP_{\text{atm}} + \frac{F_1}{A_1} = P_{\text{atm}} + \frac{F_2}{A_2} + \rho g h

Subtracting PatmP_{\text{atm}} from both sides yields: F1A1=F2A2+ρgh\frac{F_1}{A_1} = \frac{F_2}{A_2} + \rho g h

Solving for the load force F2F_2: F2=A2(F1A1−ρgh)F_2 = A_2 \left(\frac{F_1}{A_1} - \rho g h\right)

Common Pitfall: Forgetting the hydrostatic column ρgh\rho g h assumes the pistons are at the exact same elevation (F2=F1A2A1F_2 = F_1 \frac{A_2}{A_1}). When the output piston is elevated, part of the pressure generated by the input piston must support the weight of the elevated liquid column, reducing the net force available to support the external load.

03

Convert Units and Calculate

  • Input area: A1=8.00 cm2=8.00×10−4 m2A_1 = 8.00\text{ cm}^2 = 8.00 \times 10^{-4}\text{ m}^2
  • Output area: A2=200 cm2=2.00×10−2 m2A_2 = 200\text{ cm}^2 = 2.00 \times 10^{-2}\text{ m}^2

Calculate the input pressure: F1A1=110 N8.00×10−4 m2=137500 Pa\frac{F_1}{A_1} = \frac{110\text{ N}}{8.00 \times 10^{-4}\text{ m}^2} = 137500\text{ Pa}

Calculate the hydrostatic pressure of the oil column: ρgh=(860 kg/m3)(9.80 m/s2)(1.45 m)≈12221 Pa\rho g h = (860\text{ kg/m}^3)(9.80\text{ m/s}^2)(1.45\text{ m}) \approx 12221\text{ Pa}

Substitute these values to find F2F_2: F2=(2.00×10−2 m2)(137500 Pa−12221 Pa)F_2 = (2.00 \times 10^{-2}\text{ m}^2)(137500\text{ Pa} - 12221\text{ Pa}) F2=(2.00×10−2 m2)(125279 Pa)≈2505.6 NF_2 = (2.00 \times 10^{-2}\text{ m}^2)(125279\text{ Pa}) \approx 2505.6\text{ N}

Rounding to two significant figures consistent with the given precision: F2=2500 NF_2 = 2500\text{ N}

Typical errors

OverviewACEpath Teacher's Diagnosis

01 A student might add the hydrostatic head ρgh instead of subtracting it, incorrectly believing that the higher elevation increases pressure under the load piston.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    A1=8.00×10−4 m2,  A2=0.0200 m2  ⟹  P1=1108.00×10−4=137500 Pa  ⟹  ρgh=860×9.80×1.45=12219.6 PaA_1 = 8.00 \times 10^{-4}\text{ m}^2,\; A_2 = 0.0200\text{ m}^2 \implies P_1 = \frac{110}{8.00 \times 10^{-4}} = 137500\text{ Pa} \implies \rho g h = 860 \times 9.80 \times 1.45 = 12219.6\text{ Pa}

  2. Step 2

    P2=P1+ρgh=137500+12219.6=149719.6 PaP_2 = P_1 + \rho g h = 137500 + 12219.6 = 149719.6\text{ Pa}

    Correct

    P2=P1−ρgh=137500 Pa−12220 Pa=125280 PaP_2 = P_1 - \rho g h = 137500\text{ Pa} - 12220\text{ Pa} = 125280\text{ Pa}

    Because the load piston is elevated at a height hh above the input piston, the fluid pressure decreases as elevation increases (Pbottom=Ptop+ρghP_{\text{bottom}} = P_{\text{top}} + \rho g h). Consequently, the pressure directly under the elevated load piston is P2=P1−ρghP_2 = P_1 - \rho g h, not P1+ρghP_1 + \rho g h.

  3. Step 3

    F2=P2×A2=149719.6×0.0200=2994.4 NF_2 = P_2 \times A_2 = 149719.6 \times 0.0200 = 2994.4\text{ N}

    Correct

    F2=P2×A2=(125280 Pa)(0.0200 m2)≈2500 NF_2 = P_2 \times A_2 = (125280\text{ Pa})(0.0200\text{ m}^2) \approx 2500\text{ N}

    You correctly applied the relationship F2=P2A2F_2 = P_2 A_2, but your numerical result was affected by the incorrect value of P2P_2 from the previous step.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly converted the cross-sectional areas from square centimeters to square meters.

You calculated the input gauge pressure and the hydrostatic pressure component accurately.

You used the correct relation between pressure, force, and area at the output piston.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Incorrect hydrostatic pressure sign with elevation change

You treated the pressure at the higher elevation as greater than the pressure at the lower elevation.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing the direction of hydrostatic pressure variation with elevation. In a static fluid, pressure is highest at lower depths and decreases as vertical elevation increases (P2=P1−ρghP_2 = P_1 - \rho g h). Part of the pressure provided by the input piston must support the elevated column of liquid, leaving less available pressure to support the external load.

REASONING PATH
Your ACEpath teacher’s suggested approach
Pressure vs. Elevation Rule
  • In static fluids, pressure decreases with height: Phigh=Plow−ρghP_{\text{high}} = P_{\text{low}} - \rho g h, or Plow=Phigh+ρghP_{\text{low}} = P_{\text{high}} + \rho g h.

  • Always establish a reference horizontal plane at the lowest fluid surface where pressures are equal across interconnected columns.

Physical Sanity Check for Hydraulics
  • Lifting liquid to an elevated platform requires pressure, which diminishes the net lifting capacity at that elevated piston.

  • Verify that raising the output piston above the input piston reduces F2F_2 compared to the ideal level-piston case (F2<F1A2A1F_2 < F_1 \frac{A_2}{A_1}).

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Write the pressure equilibrium equation at the elevation of piston 1: P1=P2+ρghP_1 = P_2 + \rho g h.

  2. Solve for the pressure under the load piston: P2=P1−ρgh=137500 Pa−12220 Pa=125280 PaP_2 = P_1 - \rho g h = 137500\text{ Pa} - 12220\text{ Pa} = 125280\text{ Pa}.

  3. Compute the supported load force: F2=P2A2=(125280 Pa)(0.0200 m2)=2505.6 NF_2 = P_2 A_2 = (125280\text{ Pa})(0.0200\text{ m}^2) = 2505.6\text{ N}.

Final answer

F2=2500 NF_2 = 2500\text{ N} (or 2510 N2510\text{ N} to three significant figures)

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the hydrostatic pressure variation formula P=P0+ρgdP = P_0 + \rho g d vs. P=P0−ρghP = P_0 - \rho g h, keeping track of whether depth increases or elevation increases.

  • Practice sketching a single reference horizontal datum at the lower piston to visually balance column pressures before writing algebraic equations.

OverviewACEpath Teacher's Diagnosis

02 A student might neglect the hydrostatic pressure difference entirely and apply Pascal's principle directly as F2 = F1 × (A2 / A1).

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    F2/A2=F1/A1  ⟹  F2=F1×(A2/A1)F_2 / A_2 = F_1 / A_1 \implies F_2 = F_1 \times (A_2 / A_1)

    Correct

    F1A1=F2A2+ρgh  ⟹  F2=A2(F1A1−ρgh)\frac{F_1}{A_1} = \frac{F_2}{A_2} + \rho g h \implies F_2 = A_2\left(\frac{F_1}{A_1} - \rho g h\right)

    You assumed that the fluid pressures directly below both pistons are equal. Because the load piston rests at a vertical height h=1.45 mh = 1.45\text{ m} above the input piston, the pressure at the input level must balance both the load piston pressure and the hydrostatic pressure ρgh\rho g h of the elevated liquid column.

  2. Step 2

    F2=110×(200/8.00)F_2 = 110 \times (200 / 8.00)

    Correct

    F2=(2.00×10−2 m2)(110 N8.00×10−4 m2−(860 kg/m3)(9.80 m/s2)(1.45 m))F_2 = (2.00 \times 10^{-2}\text{ m}^2)\left(\frac{110\text{ N}}{8.00 \times 10^{-4}\text{ m}^2} - (860\text{ kg/m}^3)(9.80\text{ m/s}^2)(1.45\text{ m})\right)

    You substituted the given values correctly into your uncorrected formula, but the calculation is missing the subtraction of the hydrostatic pressure term ρgh\rho g h.

  3. Step 3

    F2=110×25=2750 NF_2 = 110 \times 25 = 2750\text{ N}

    Correct

    F2≈2500 NF_2 \approx 2500\text{ N}

    Your arithmetic evaluation was carried out cleanly, but the resulting force is overestimated because the hydrostatic fluid column was not accounted for.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified the mechanical advantage concept relating the input force to the ratio of piston areas.

You performed the algebraic manipulation and arithmetic steps accurately without calculation errors.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Neglected hydrostatic elevation head

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You applied standard Pascal's principle (P1=P2P_1 = P_2) without checking whether the fluid surfaces are at the same horizontal reference level. When fluid columns have an elevation difference hh, static equilibrium requires equating pressures at the same horizontal datum: P1=P2+ρghP_1 = P_2 + \rho g h.

REASONING PATH
Your ACEpath teacher’s suggested approach
Establish a Common Horizontal Datum
  • In a continuous static liquid, pressures are equal only at the same vertical level: Pleft, datum=Pright, datumP_{\text{left, datum}} = P_{\text{right, datum}}.

  • Always draw a horizontal reference line at the lower piston surface and sum the hydrostatic column ρgh\rho g h under the higher piston.

Account for Fluid Column Weight
  • An elevated piston requires part of the input pressure simply to support the weight of the fluid column of height hh.

  • Subtract ρgh\rho g h from the available input pressure before multiplying by the output piston area A2A_2.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Choose the horizontal level of the lower input piston as the reference datum: P1=P2+ρghP_1 = P_2 + \rho g h.

  2. Express the pressures in terms of forces and areas: F1A1=F2A2+ρgh\frac{F_1}{A_1} = \frac{F_2}{A_2} + \rho g h.

  3. Convert areas to standard SI units: A1=8.00×10−4 m2A_1 = 8.00 \times 10^{-4}\text{ m}^2 and A2=2.00×10−2 m2A_2 = 2.00 \times 10^{-2}\text{ m}^2.

  4. Compute the input pressure: F1A1=110 N8.00×10−4 m2=137500 Pa\frac{F_1}{A_1} = \frac{110\text{ N}}{8.00 \times 10^{-4}\text{ m}^2} = 137500\text{ Pa}.

  5. Compute the hydrostatic pressure of the oil column: ρgh=860 kg/m3×9.80 m/s2×1.45 m≈12221 Pa\rho g h = 860\text{ kg/m}^3 \times 9.80\text{ m/s}^2 \times 1.45\text{ m} \approx 12221\text{ Pa}.

  6. Calculate the net pressure available for the load: Pnet=137500 Pa−12221 Pa=125279 PaP_{\text{net}} = 137500\text{ Pa} - 12221\text{ Pa} = 125279\text{ Pa}.

  7. Multiply by the output area: F2=(2.00×10−2 m2)(125279 Pa)≈2505.6 N≈2500 NF_2 = (2.00 \times 10^{-2}\text{ m}^2)(125279\text{ Pa}) \approx 2505.6\text{ N} \approx 2500\text{ N}.

Final answer

F2=2500 NF_2 = 2500\text{ N}

NEXT STEPS
Final Takeaways from Your Teacher
  • Sketch the U-tube hydraulic system and mark the lower piston as your horizontal reference line.

  • Practice identifying whether the output piston is higher or lower than the input piston to decide whether to add or subtract ρgh\rho g h.

OverviewACEpath Teacher's Diagnosis

03 A student might incorrectly convert the areas by dividing by 100 rather than 10000 when converting cm² to m².

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    A1=8.00100=0.0800 m2,  A2=200100=2.00 m2A_1 = \frac{8.00}{100} = 0.0800\text{ m}^2,\; A_2 = \frac{200}{100} = 2.00\text{ m}^2

    Correct

    A1=8.0010,000=8.00×10−4 m2,  A2=20010,000=2.00×10−2 m2A_1 = \frac{8.00}{10\text{,}000} = 8.00 \times 10^{-4}\text{ m}^2,\; A_2 = \frac{200}{10\text{,}000} = 2.00 \times 10^{-2}\text{ m}^2

    You divided by 100100 as if converting linear centimeters to meters. Because area scales with the square of length, 1 m2=(100 cm)2=10,000 cm21\text{ m}^2 = (100\text{ cm})^2 = 10{,}000\text{ cm}^2, so you must divide by 10,00010{,}000.

  2. Step 2

    P1=1100.0800=1375 PaP_1 = \frac{110}{0.0800} = 1375\text{ Pa}

    Correct

    P1=F1A1=110 N8.00×10−4 m2=137,500 PaP_1 = \frac{F_1}{A_1} = \frac{110\text{ N}}{8.00 \times 10^{-4}\text{ m}^2} = 137\text{,}500\text{ Pa}

    Your formula for pressure is correct, but substituting your incorrectly converted area A1A_1 produced an input pressure that is 100100 times too small.

  3. Step 3

    ρgh=860×9.80×1.45=12219.6 Pa\rho g h = 860 \times 9.80 \times 1.45 = 12219.6\text{ Pa}

  4. Step 4

    P2=1375−12219.6=−10844.6 PaP_2 = 1375 - 12219.6 = -10844.6\text{ Pa}

    Correct

    P2=P1−ρgh=137,500 Pa−12,221 Pa=125,279 PaP_2 = P_1 - \rho g h = 137\text{,}500\text{ Pa} - 12\text{,}221\text{ Pa} = 125\text{,}279\text{ Pa}

    You applied the correct hydrostatic equilibrium condition (P2=P1−ρghP_2 = P_1 - \rho g h), but the underestimated P1P_1 caused this difference to turn negative.

  5. Step 5

    F2=−10844.6×2.00=−21689.2 NF_2 = -10844.6 \times 2.00 = -21689.2\text{ N}

    Correct

    F2=P2A2=(125,279 Pa)(2.00×10−2 m2)≈2500 NF_2 = P_2 A_2 = (125\text{,}279\text{ Pa})(2.00 \times 10^{-2}\text{ m}^2) \approx 2500\text{ N}

    Your method of multiplying gauge pressure by area was correct, but the carried-over errors in P2P_2 and A2A_2 affected your final result.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified that the elevated oil column creates a hydrostatic pressure difference between the two pistons.

You accurately calculated the hydrostatic pressure term ρgh\rho g h using the correct density, gravity, and height values.

You correctly subtracted the column pressure ρgh\rho g h from the input pressure to find the net gauge pressure at the output piston.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Unit Conversion Error (Area Scaling)

You divided by 100100 instead of 1002=10,000100^2 = 10{,}000 when converting cm2\text{cm}^2 to m2\text{m}^2.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Treating two-dimensional units (area) as one-dimensional (linear) units during metric conversion. When converting square centimeters to square meters, the linear scale factor of 10−2 m/cm10^{-2}\text{ m/cm} must also be squared: (10−2 m)2=10−4 m2(10^{-2}\text{ m})^2 = 10^{-4}\text{ m}^2.

REASONING PATH
Your ACEpath teacher’s suggested approach
Area Conversion Check
  • 1 m=100 cm  ⟹  1 m2=(100 cm)2=10,000 cm2=104 cm21\text{ m} = 100\text{ cm} \implies 1\text{ m}^2 = (100\text{ cm})^2 = 10{,}000\text{ cm}^2 = 10^4\text{ cm}^2

  • Always write out (1 m/100 cm)2=1 m2/10,000 cm2(1\text{ m} / 100\text{ cm})^2 = 1\text{ m}^2 / 10{,}000\text{ cm}^2 before converting any area.

Physical Reality Check
  • An applied downward force on a hydraulic lift should support a positive upward load force.

  • If your calculated output pressure or force turns out negative, immediately re-check your area conversions and pressure magnitudes.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Convert areas using 1 cm2=10−4 m21\text{ cm}^2 = 10^{-4}\text{ m}^2: A1=8.00×10−4 m2A_1 = 8.00 \times 10^{-4}\text{ m}^2 and A2=2.00×10−2 m2A_2 = 2.00 \times 10^{-2}\text{ m}^2.

  2. Recalculate input pressure: P1=110 N8.00×10−4 m2=137,500 PaP_1 = \frac{110\text{ N}}{8.00 \times 10^{-4}\text{ m}^2} = 137\text{,}500\text{ Pa}.

  3. Subtract the hydrostatic column pressure: P2=137,500 Pa−12,221 Pa=125,279 PaP_2 = 137\text{,}500\text{ Pa} - 12\text{,}221\text{ Pa} = 125\text{,}279\text{ Pa}.

  4. Compute the load force: F2=P2A2=(125,279 Pa)(2.00×10−2 m2)≈2505.6 NF_2 = P_2 A_2 = (125\text{,}279\text{ Pa})(2.00 \times 10^{-2}\text{ m}^2) \approx 2505.6\text{ N}.

Final answer

F2=2500 NF_2 = 2500\text{ N} (or 2.5×103 N2.5 \times 10^3\text{ N} to two significant figures)

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice converting compound metric units (1 cm2=10−4 m21\text{ cm}^2 = 10^{-4}\text{ m}^2, 1 cm3=10−6 m31\text{ cm}^3 = 10^{-6}\text{ m}^3) using dimensional analysis brackets.

  • Perform a quick order-of-magnitude check on pressure values: atmospheric pressure is ≈105 Pa\approx 10^5\text{ Pa}, so a modest force on a small piston typically produces 104 to 105 Pa10^4\text{ to }10^5\text{ Pa}, not 103 Pa10^3\text{ Pa}.

Lock it in

Similar question

01

A hydraulic jack filled with oil (ρ=900 kg/m3\rho = 900\text{ kg/m}^3) has an input piston of area A1=5.0 cm2A_1 = 5.0\text{ cm}^2 and an output piston of area A2=100 cm2A_2 = 100\text{ cm}^2. A force of F1=200 NF_1 = 200\text{ N} is applied downward on the input piston. If the output piston rests at an elevation h=2.0 mh = 2.0\text{ m} above the input piston, find the pressure P2P_2 directly under the output piston. Take g=9.80 m/s2g = 9.80\text{ m/s}^2.

Answer

P1=200 N5.0×10−4 m2=4.00×105 PaP_1 = \frac{200\text{ N}}{5.0 \times 10^{-4}\text{ m}^2} = 4.00 \times 10^5\text{ Pa}. The hydrostatic head is ρgh=(900)(9.80)(2.0)=17640 Pa\rho g h = (900)(9.80)(2.0) = 17640\text{ Pa}. Subtracting because the output piston is higher: P2=P1−ρgh=400000−17640=382360 Pa≈3.82×105 PaP_2 = P_1 - \rho g h = 400000 - 17640 = 382360\text{ Pa} \approx 3.82 \times 10^5\text{ Pa}.

02

A hydraulic lift filled with water (ρ=1000 kg/m3\rho = 1000\text{ kg/m}^3) supports a car of mass m=1200 kgm = 1200\text{ kg} on a platform of area A2=0.080 m2A_2 = 0.080\text{ m}^2. The narrow piston has area A1=1.0×10−3 m2A_1 = 1.0 \times 10^{-3}\text{ m}^2. What downward force F1F_1 must be applied on the narrow piston when the car is held in static equilibrium at a height h=1.5 mh = 1.5\text{ m} above the narrow piston? Take g=9.80 m/s2g = 9.80\text{ m/s}^2.

Answer

Load force is F2=mg=(1200)(9.80)=11760 NF_2 = mg = (1200)(9.80) = 11760\text{ N}. Pressure under load piston is P2=11760 N0.080 m2=147000 PaP_2 = \frac{11760\text{ N}}{0.080\text{ m}^2} = 147000\text{ Pa}. Because the narrow piston is at the lower level, P1=P2+ρgh=147000+(1000)(9.80)(1.5)=147000+14700=161700 PaP_1 = P_2 + \rho g h = 147000 + (1000)(9.80)(1.5) = 147000 + 14700 = 161700\text{ Pa}. Thus F1=P1A1=(161700 Pa)(1.0×10−3 m2)≈162 NF_1 = P_1 A_1 = (161700\text{ Pa})(1.0 \times 10^{-3}\text{ m}^2) \approx 162\text{ N}.

03

In a U-tube hydraulic apparatus, piston 1 has area A1=4.0 cm2A_1 = 4.0\text{ cm}^2 and piston 2 has area A2=50 cm2A_2 = 50\text{ cm}^2. The fluid has density ρ=800 kg/m3\rho = 800\text{ kg/m}^3. If piston 1 is positioned at an elevation h=2.5 mh = 2.5\text{ m} higher than piston 2, determine the load force F2F_2 supported on piston 2 when a downward force of F1=80 NF_1 = 80\text{ N} is exerted on piston 1. Take g=9.80 m/s2g = 9.80\text{ m/s}^2.

Answer

Pressure under piston 1 is P1=804.0×10−4=2.00×105 PaP_1 = \frac{80}{4.0 \times 10^{-4}} = 2.00 \times 10^5\text{ Pa}. Here, piston 2 is lower by hh, so fluid pressure increases toward piston 2: P2=P1+ρgh=200000+(800)(9.80)(2.5)=200000+19600=219600 PaP_2 = P_1 + \rho g h = 200000 + (800)(9.80)(2.5) = 200000 + 19600 = 219600\text{ Pa}. The load force is F2=P2A2=(219600 Pa)(5.0×10−3 m2)=1098 N≈1.1×103 NF_2 = P_2 A_2 = (219600\text{ Pa})(5.0 \times 10^{-3}\text{ m}^2) = 1098\text{ N} \approx 1.1 \times 10^3\text{ N}.

Loading workspace…