Resources
An analytical chemist standardizes a aqueous hydrochloric acid () titrant in a climate-controlled laboratory at . In an unconditioned field laboratory at , a technician fills a calibrated Class A glass burette to deliver a nominal volume of of this titrant to reach the stoichiometric equivalence point of an unknown alkaline solution. The linear expansion coefficient of the burette glass is (so ), and the volumetric expansion coefficient of the dilute aqueous titrant is . (a) Calculate the actual physical volume of solution delivered at . (b) Calculate the thermally corrected molarity of the titrant at and find the true number of moles of delivered.
Answer and steps
Final answer
(a) ; (b) ;
Steps
Part (a): Actual Physical Volume Delivered by the Burette
-
Understand volumetric expansion of the glass container: The burette was calibrated at to read the exact volume enclosed. When heated to , the temperature change is:
A hollow glass vessel expands internally in exactly the same way as a solid block of glass of the same outer dimensions. Therefore, the volume marked by the scale lines expands according to the volumetric thermal expansion coefficient of glass, .
- Calculate the true delivered volume :
Part (b): Corrected Molarity and Moles Delivered
-
Effect of thermal expansion on molarity: As the aqueous solution warms, its volume increases according to its volumetric coefficient of expansion :
Because the amount of solute in a fixed mass of solution does not change, molarity () is inversely proportional to the volume of the solution:
- Calculate the true number of moles delivered (): Multiply the actual concentration at the field temperature by the actual physical volume delivered:
Common Pitfall: Assuming that the expansion of the glass compensates for the expansion of the liquid. Because liquids have significantly higher volumetric expansion coefficients than solids ( in this case), the decrease in solution molarity has a much larger impact than the slight increase in the burette's volume capacity.
Typical errors
01 The student uses the linear expansion coefficient of glass instead of the volumetric expansion coefficient when calculating the burette volume expansion.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1Correct
You calculated the temperature increase correctly, but you substituted the linear expansion coefficient into the volume expansion formula. Because volume expands in three dimensions, a hollow container expands internally with volumetric expansion coefficient .
- Step 2
- Step 3Correct
Your method of multiplying the corrected molarity by the delivered volume was correct, but your numerical answer was slightly off due to the volume error from Step 1.
WHAT YOU DID WELL
Compliments from Your TeacherYou accurately found the temperature difference .
You correctly applied the volumetric expansion formula to adjust the concentration of the liquid solution.
You used the correct relationship to calculate the final number of moles delivered.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou accidentally selected the linear coefficient instead of the volumetric coefficient when computing volume changes.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConfusing linear expansion () with volumetric expansion (), where for isotropic solids such as glass.
REASONING PATH
Your ACEpath teacher’s suggested approach- Match Expansion Dimension to Quantity
Use for 1D length changes, for 2D area changes, and for 3D volume changes.
Always verify that the units and symbols in your formula match volume ( or ) using , not .
- Cavity Expansion Principle
The internal cavity of an isotropic solid container expands at the exact same volumetric rate as a solid object of the same material: .
Treat the volumetric markings of volumetric glassware as expanding with .
CORRECTED PATH
ACEpath Teacher's DemonstrationCalculate true physical volume using volumetric expansion: .
Calculate delivered moles using the correct volume: .
(a) ; (b) ;
02 The student incorrectly assumes that the expansion of the titrant solution directly increases the delivered volume from the burette instead of using the glass expansion.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
You substituted the liquid volumetric expansion coefficient instead of the volumetric expansion coefficient of the glass container . The physical volume defined between graduation marks on calibrated volumetric glassware depends entirely on the thermal expansion of the glass.
- Step 3
- Step 4Correct
Your formula for moles delivered is correct, but using the incorrect delivered volume from Step 2 caused the expansion factors to cancel out and gave an inaccurate mole count.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly calculated the temperature rise of .
You correctly recognized that molarity decreases inversely with the volumetric expansion of the solvent.
You correctly related molarity, delivered volume, and total moles delivered.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeNo, this is a conceptual misunderstanding about what determines the volume delivered by a calibrated container.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisYou assumed that the expansion of the liquid directly dictates the volume delivered between two fixed burette graduation lines. In volumetric glassware, the liquid level is adjusted by eye to match calibrated physical markings on the vessel walls. Consequently, the actual volume contained or dispensed between markings is governed solely by the expansion of the hollow glass cavity (), while the liquid expansion () governs only the concentration change (molarity dilution).
REASONING PATH
Your ACEpath teacher’s suggested approach- Container Volume vs. Liquid Volume
The internal capacity between graduation marks on any rigid vessel expands as .
Always use the container's expansion coefficient when calculating the true volume defined by calibrated glassware markings.
- Solution Molarity Dilution
Molarity is inversely proportional to liquid volume: .
Use the liquid solution's coefficient strictly for adjusting concentration, not for the glassware markings.
CORRECTED PATH
ACEpath Teacher's DemonstrationRecalculate the delivered volume using the volumetric expansion of glass: .
Multiply the corrected delivered volume by the corrected molarity: .
(a) ; (b) ; $n_{} = 3.985 10^{-3}_
03 The student multiplies by the expansion factor rather than dividing when computing the temperature-corrected concentration, incorrectly treating molarity as expanding with temperature.
Sample Student Work
Reviewed by ACEpath TeacherStep-by-Step Review
Walk Through It with Your Teacher- Step 1
- Step 2Correct
Molarity is defined as moles of solute per unit volume (). When the temperature rises, the solution volume expands, so the concentration must decrease rather than increase.
- Step 3Correct
You correctly set up , but the final numerical value was affected by your previous molarity calculation.
WHAT YOU DID WELL
Compliments from Your TeacherYou correctly computed the temperature difference between the calibration and field conditions.
You accurately applied the volumetric expansion formula to determine the expanded capacity of the glass vessel.
You correctly multiplied concentration by volume to calculate the total moles delivered.
THE ERROR
Where Your ACEpath Teacher Spotted the MistakeYou treated concentration as expanding alongside volume by multiplying by instead of dividing by it.
WHY IT HAPPENED
ACEpath Teacher's DiagnosisConflating intensive quantities inversely dependent on volume (such as molarity or density ) with extensive spatial dimensions that expand directly with temperature ().
REASONING PATH
Your ACEpath teacher’s suggested approach- Volume vs. Concentration Relationship
; for a fixed amount of solute, molarity is inversely proportional to volume.
When temperature increases and liquid expands (), verify that your corrected concentration decreases ().
- Thermal Scaling Form
for small .
Place the thermal expansion factor in the denominator when correcting concentration or density.
CORRECTED PATH
ACEpath Teacher's DemonstrationWrite the definition of molarity at the field temperature: .
Substitute the values: .
Calculate true moles delivered: .
(a) ; (b) ;
Lock it in
How are the linear expansion coefficient () and volumetric expansion coefficient () related for an isotropic solid?
, because thermal expansion occurs equally along all three spatial dimensions.
Similar question
A borosilicate volumetric flask is calibrated at . The linear expansion coefficient of the glass is . What is the actual internal capacity of the flask at ?
Answer
. Key steps: ; ; .
An aqueous solution with volumetric expansion coefficient has a concentration of at . Calculate its concentration at .
Answer
. Key steps: ; .
A glass burette () calibrated at delivers of an ethanol solution () at . If the solution was prepared as at , find the actual moles of ethanol delivered at .
Answer
. Key steps: ; ; ; ; (or without intermediate rounding).