Resources

An incompressible hydraulic fluid flows through a cylindrical conduit of radius r1=5.00 cmr_1 = 5.00\text{ cm} at an average speed of v1=2.10 m/sv_1 = 2.10\text{ m/s}. The conduit transitions into a narrower section where the fluid speed reaches v2=8.40 m/sv_2 = 8.40\text{ m/s}. Determine the required radius r2r_2 of the constricted section and the ratio of the cross-sectional area of the constriction to the initial area, A2A1\frac{A_2}{A_1}.

Answer and steps

Final answer

r2=2.50 cmr_2 = 2.50\text{ cm}, A2A1=0.250\frac{A_2}{A_1} = 0.250

Steps

01

Apply the Continuity Equation for Incompressible Fluids

For an incompressible fluid undergoing steady flow through a conduit with no leaks or additions, the volume flow rate QQ remains constant along the pipe:

Q=A1v1=A2v2Q = A_1 v_1 = A_2 v_2

where A1A_1 and A2A_2 are the cross-sectional areas, and v1v_1 and v2v_2 are the average flow speeds at the wide and narrow sections, respectively.


02

Determine the Ratio of the Cross-Sectional Areas

Rearranging the continuity equation gives the ratio of the constricted area to the initial area:

A2A1=v1v2\frac{A_2}{A_1} = \frac{v_1}{v_2}

Substitute the given velocities:

A2A1=2.10 m/s8.40 m/s=0.250\frac{A_2}{A_1} = \frac{2.10\text{ m/s}}{8.40\text{ m/s}} = 0.250


03

Calculate the Radius of the Constriction

For a cylindrical conduit with circular cross-sections, the area is A=πr2A = \pi r^2. Substituting this into the area ratio yields:

A2A1=πr22πr12=(r2r1)2\frac{A_2}{A_1} = \frac{\pi r_2^2}{\pi r_1^2} = \left(\frac{r_2}{r_1}\right)^2

Solve for the radius r2r_2:

r2r1=A2A1=0.250=0.500\frac{r_2}{r_1} = \sqrt{\frac{A_2}{A_1}} = \sqrt{0.250} = 0.500

r2=0.500⋅r1=0.500⋅5.00 cm=2.50 cmr_2 = 0.500 \cdot r_1 = 0.500 \cdot 5.00\text{ cm} = 2.50\text{ cm}

Common Pitfall: A common mistake is setting the ratio of radii equal to the ratio of speeds (r1v1=r2v2r_1 v_1 = r_2 v_2). The continuity equation relates cross-sectional area to speed, so speed is inversely proportional to the square of the radius (v∝1r2v \propto \frac{1}{r^2}), not the radius itself.

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student assumes radius is inversely proportional to speed instead of area, omitting the square root and obtaining r₂ = 1.25 cm.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    r1v1=r2v2  ⟹  r2=r1(v1/v2)  ⟹  r2=(5.00)(2.10/8.40)  ⟹  r2=1.25 cmr_1 v_1 = r_2 v_2 \implies r_2 = r_1(v_1 / v_2) \implies r_2 = (5.00)(2.10 / 8.40) \implies r_2 = 1.25\text{ cm}

    Correct

    A1v1=A2v2  ⟹  πr12v1=πr22v2  ⟹  r2=r1v1v2=5.00⋅2.108.40=2.50 cmA_1 v_1 = A_2 v_2 \implies \pi r_1^2 v_1 = \pi r_2^2 v_2 \implies r_2 = r_1 \sqrt{\frac{v_1}{v_2}} = 5.00 \cdot \sqrt{\frac{2.10}{8.40}} = 2.50\text{ cm}

    You treated the radius as inversely proportional to speed by writing r1v1=r2v2r_1 v_1 = r_2 v_2. The continuity equation applies to the cross-sectional area, A=πr2A = \pi r^2, meaning speed is inversely proportional to r2r^2, so r2r_2 requires taking the square root of the velocity ratio.

  2. Step 2

    A2A1=v1v2  ⟹  A2A1=2.108.40  ⟹  A2A1=0.250\frac{A_2}{A_1} = \frac{v_1}{v_2} \implies \frac{A_2}{A_1} = \frac{2.10}{8.40} \implies \frac{A_2}{A_1} = 0.250

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly stated and calculated the area ratio using the continuity equation A2A1=v1v2\frac{A_2}{A_1} = \frac{v_1}{v_2}.

You substituted the given speed values accurately into the area ratio equation.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Linear radius scaling instead of area scaling

none

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You assumed that the pipe radius scales linearly with fluid speed (r1v1=r2v2r_1 v_1 = r_2 v_2), forgetting that volume flow rate depends on the two-dimensional cross-sectional area (A=πr2A = \pi r^2), which introduces a square-root relationship for the radius.

REASONING PATH
Your ACEpath teacher’s suggested approach
Continuity Equation Involves Area
  • For an incompressible fluid, Q=A1v1=A2v2Q = A_1 v_1 = A_2 v_2, not r1v1=r2v2r_1 v_1 = r_2 v_2.

  • Always write the continuity equation with cross-sectional area AA first, then express AA in terms of radius as A=πr2A = \pi r^2 before solving for radius.

Radius Scales with the Square Root of Area
  • Since A=πr2A = \pi r^2, the ratio of radii is r2r1=A2A1=v1v2\frac{r_2}{r_1} = \sqrt{\frac{A_2}{A_1}} = \sqrt{\frac{v_1}{v_2}}.

  • Remember to take the square root of the velocity ratio when calculating a change in radius or diameter.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Start from the continuity equation: A1v1=A2v2A_1 v_1 = A_2 v_2.

  2. Substitute A=πr2A = \pi r^2: πr12v1=πr22v2\pi r_1^2 v_1 = \pi r_2^2 v_2.

  3. Divide by π\pi and solve for r2r_2: r2=r1v1v2r_2 = r_1 \sqrt{\frac{v_1}{v_2}}.

  4. Substitute the numerical values: r2=(5.00 cm)2.10 m/s8.40 m/s=5.00⋅0.250=5.00⋅0.500=2.50 cmr_2 = (5.00\text{ cm}) \sqrt{\frac{2.10\text{ m/s}}{8.40\text{ m/s}}} = 5.00 \cdot \sqrt{0.250} = 5.00 \cdot 0.500 = 2.50\text{ cm}.

Final answer

r2=2.50 cm,A2A1=0.250r_2 = 2.50\text{ cm},\quad \frac{A_2}{A_1} = 0.250

NEXT STEPS
Final Takeaways from Your Teacher
  • Review how area relates to linear dimensions (rr or dd) in flow problems by writing A=πr2A = \pi r^2 explicitly every time.

  • Practice checking whether your formula gives the correct physical units and dimensions: flow rate is volume per time ([L3/T][L^3/T]), which requires [L2]×[L/T][L^2] \times [L/T].

OverviewACEpath Teacher's Diagnosis

02 The student inverts the speed ratio in the continuity equation, setting r₂ = r₁√(v₂/v₁) and finding an expanded radius of 10.0 cm.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    A1v1=A2v2A_1 v_1 = A_2 v_2

  2. Step 2

    r2=r1v2v1r_2 = r_1 \sqrt{\frac{v_2}{v_1}}

    Correct

    r2=r1v1v2r_2 = r_1 \sqrt{\frac{v_1}{v_2}}

    You inverted the velocity ratio when solving for the radius. Dividing A1v1=A2v2A_1 v_1 = A_2 v_2 by A1v2A_1 v_2 yields A2A1=v1v2\frac{A_2}{A_1} = \frac{v_1}{v_2}, which gives r2=r1v1v2r_2 = r_1 \sqrt{\frac{v_1}{v_2}}.

  3. Step 3

    r2=5.00×8.402.10  ⟹  r2=5.00×4.00  ⟹  r2=10.0 cmr_2 = 5.00 \times \sqrt{\frac{8.40}{2.10}} \implies r_2 = 5.00 \times \sqrt{4.00} \implies r_2 = 10.0\text{ cm}

    Correct

    r2=5.00 cm×2.10 m/s8.40 m/s=5.00 cm×0.250=2.50 cmr_2 = 5.00\text{ cm} \times \sqrt{\frac{2.10\text{ m/s}}{8.40\text{ m/s}}} = 5.00\text{ cm} \times \sqrt{0.250} = 2.50\text{ cm}

    Your arithmetic follows correctly from your inverted equation, but propagating the inverted ratio produced an expanded radius of 10.0 cm10.0\text{ cm} rather than the constricted radius of 2.50 cm2.50\text{ cm}.

  4. Step 4

    A2A1=v2v1=8.402.10=4.00\frac{A_2}{A_1} = \frac{v_2}{v_1} = \frac{8.40}{2.10} = 4.00

    Correct

    A2A1=v1v2=2.10 m/s8.40 m/s=0.250\frac{A_2}{A_1} = \frac{v_1}{v_2} = \frac{2.10\text{ m/s}}{8.40\text{ m/s}} = 0.250

    You set the area ratio proportional to the speed ratio instead of inversely proportional. From A1v1=A2v2A_1 v_1 = A_2 v_2, the area ratio is A2A1=v1v2\frac{A_2}{A_1} = \frac{v_1}{v_2}.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified and wrote down the continuity equation A1v1=A2v2A_1 v_1 = A_2 v_2.

You correctly related circular cross-sectional area to radius using A=πr2A = \pi r^2.

You carried out your arithmetic and square-root calculations accurately.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Inverted ratio in algebraic rearrangement

You swapped the numerator and denominator of the velocity ratio when isolating A2A1\frac{A_2}{A_1}.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated area and velocity as directly proportional rather than inversely proportional when cross-multiplying and dividing terms in A1v1=A2v2A_1 v_1 = A_2 v_2.

REASONING PATH
Your ACEpath teacher’s suggested approach
Isolate Inverse Proportions Carefully
  • When a product is constant (x1y1=x2y2x_1 y_1 = x_2 y_2), dividing both sides by x1y2x_1 y_2 yields y1y2=x2x1\frac{y_1}{y_2} = \frac{x_2}{x_1}. The indices in the ratio must be swapped.

  • Divide step by step rather than writing the ratio from memory: divide both sides by A1A_1, then divide both sides by v2v_2.

Physical Sanity Check on Constrictions
  • In an incompressible flow, a constricted (narrower) pipe must have A2<A1A_2 < A_1 and r2<r1r_2 < r_1 whenever v2>v1v_2 > v_1.

  • Before writing your final answer, verify that higher speed corresponds to a smaller area ratio ( <1\,< 1) and a smaller radius.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. A2A1=v1v2=2.10 m/s8.40 m/s=0.250\frac{A_2}{A_1} = \frac{v_1}{v_2} = \frac{2.10\text{ m/s}}{8.40\text{ m/s}} = 0.250

  2. r2=r1A2A1=5.00 cm×0.250=5.00 cm×0.500=2.50 cmr_2 = r_1 \sqrt{\frac{A_2}{A_1}} = 5.00\text{ cm} \times \sqrt{0.250} = 5.00\text{ cm} \times 0.500 = 2.50\text{ cm}

Final answer

r2=2.50 cmr_2 = 2.50\text{ cm}, A2A1=0.250\frac{A_2}{A_1} = 0.250

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice isolating variables in product-form conservation laws like P1V1=P2V2P_1 V_1 = P_2 V_2 and A1v1=A2v2A_1 v_1 = A_2 v_2 to avoid ratio inversion.

  • Perform a quick qualitative sanity check on every fluid problem: if the fluid speeds up, the pipe must get narrower.

OverviewACEpath Teacher's Diagnosis

03 The student squares the velocity ratio instead of taking its square root when solving for radius from area, yielding r₂ = 0.313 cm.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    πr12v1=πr22v2\pi r_1^2 v_1 = \pi r_2^2 v_2

  2. Step 2

    r2=r1(v1/v2)2  ⟹  r2=5.00×(2.108.40)2  ⟹  r2=5.00×(0.250)2r_2 = r_1 (v_1/v_2)^2 \implies r_2 = 5.00 \times \left(\frac{2.10}{8.40}\right)^2 \implies r_2 = 5.00 \times (0.250)^2

    Correct

    r22=r12(v1v2)  ⟹  r2=r1v1v2=5.00×0.250r_2^2 = r_1^2 \left(\frac{v_1}{v_2}\right) \implies r_2 = r_1 \sqrt{\frac{v_1}{v_2}} = 5.00 \times \sqrt{0.250}

    When solving r12v1=r22v2r_1^2 v_1 = r_2^2 v_2 for r2r_2, dividing by v2v_2 gives r22=r12(v1v2)r_2^2 = r_1^2\left(\frac{v_1}{v_2}\right). Taking the square root of both sides requires r2=r1v1v2r_2 = r_1 \sqrt{\frac{v_1}{v_2}}, but you multiplied by (v1v2)2\left(\frac{v_1}{v_2}\right)^2 instead.

  3. Step 3

    r2=0.313 cmr_2 = 0.313\text{ cm}

    Correct

    r2=5.00×0.500=2.50 cmr_2 = 5.00 \times 0.500 = 2.50\text{ cm}

    This numerical value follows directly from squaring the speed ratio rather than taking its square root.

  4. Step 4

    A2A1=v1v2  ⟹  A2A1=2.108.40  ⟹  A2A1=0.250\frac{A_2}{A_1} = \frac{v_1}{v_2} \implies \frac{A_2}{A_1} = \frac{2.10}{8.40} \implies \frac{A_2}{A_1} = 0.250

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly applied the continuity equation A1v1=A2v2A_1 v_1 = A_2 v_2 for steady incompressible flow.

You accurately calculated the area ratio A2A1=0.250\frac{A_2}{A_1} = 0.250 from the speed ratio.

You preserved proper units and clearly organized your steps for both parts of the problem.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Algebraic rearrangement error (exponent inversion)

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You inverted the power relationship when isolating a variable under a square: instead of taking the square root to undo r22=r12(v1v2)r_2^2 = r_1^2\left(\frac{v_1}{v_2}\right), you squared the velocity ratio.

REASONING PATH
Your ACEpath teacher’s suggested approach
Undoing powers during algebraic isolation
  • If x2=ax^2 = a, then x=a=a1/2x = \sqrt{a} = a^{1/2}, not a2a^2.

  • Write out the intermediate equation r22=r12(v1v2)r_2^2 = r_1^2\left(\frac{v_1}{v_2}\right) explicitly before taking the square root of both sides.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. r22=r12(v1v2)r_2^2 = r_1^2\left(\frac{v_1}{v_2}\right)

  2. Take the square root of both sides: r2=r1v1v2r_2 = r_1\sqrt{\frac{v_1}{v_2}}

  3. Substitute the known values: r2=5.00 cm×2.108.40=5.00 cm×0.250=5.00 cm×0.500r_2 = 5.00\text{ cm} \times \sqrt{\frac{2.10}{8.40}} = 5.00\text{ cm} \times \sqrt{0.250} = 5.00\text{ cm} \times 0.500

Final answer

r2=2.50 cmr_2 = 2.50\text{ cm}, A2A1=0.250\frac{A_2}{A_1} = 0.250

NEXT STEPS
Final Takeaways from Your Teacher
  • Always write out the squared term r22r_2^2 alone on one side before extracting the root.

  • Check your answer with a quick proportionality check: if speed increases by a factor of 4, the area drops by a factor of 4, so the radius drops by 4=2\sqrt{4} = 2, not 42=164^2 = 16.

Lock it in

Similar question

01

Water flows through a garden hose of diameter d1=2.0 cmd_1 = 2.0\text{ cm} at a speed of 1.5 m/s1.5\text{ m/s}. It enters a nozzle with diameter d2=0.50 cmd_2 = 0.50\text{ cm}. Calculate the speed of water exiting the nozzle, v2v_2.

Answer

v2=24 m/sv_2 = 24\text{ m/s}. Using the continuity equation, A1v1=A2v2  ⟹  d12v1=d22v2A_1 v_1 = A_2 v_2 \implies d_1^2 v_1 = d_2^2 v_2. Thus, v2=v1(d1d2)2=(1.5 m/s)(2.00.50)2=1.5×16=24 m/sv_2 = v_1 \left(\frac{d_1}{d_2}\right)^2 = (1.5\text{ m/s}) \left(\frac{2.0}{0.50}\right)^2 = 1.5 \times 16 = 24\text{ m/s}.

02

An oil pipeline with radius r1=12.0 cmr_1 = 12.0\text{ cm} carries fluid at v1=0.80 m/sv_1 = 0.80\text{ m/s}. The pipe expands to a wider section where the fluid speed drops to v2=0.20 m/sv_2 = 0.20\text{ m/s}. Find the radius r2r_2 of the expanded section and the area ratio A2A1\frac{A_2}{A_1}.

Answer

r2=24.0 cmr_2 = 24.0\text{ cm}, A2A1=4.0\frac{A_2}{A_1} = 4.0. By continuity, A2A1=v1v2=0.800.20=4.0\frac{A_2}{A_1} = \frac{v_1}{v_2} = \frac{0.80}{0.20} = 4.0. Since A2A1=(r2r1)2\frac{A_2}{A_1} = \left(\frac{r_2}{r_1}\right)^2, we have r2r1=4.0=2.0\frac{r_2}{r_1} = \sqrt{4.0} = 2.0, yielding r2=2.0×12.0 cm=24.0 cmr_2 = 2.0 \times 12.0\text{ cm} = 24.0\text{ cm}.

03

A horizontal main pipe of radius r0=6.0 cmr_0 = 6.0\text{ cm} carries water at speed v0=1.0 m/sv_0 = 1.0\text{ m/s}. It splits into 4 identical, parallel smaller pipes, each having a radius of r=1.5 cmr = 1.5\text{ cm}. Determine the flow speed vv in each of the smaller pipes.

Answer

v=4.0 m/sv = 4.0\text{ m/s}. Total flow rate is conserved: A0v0=4(Av)  ⟹  πr02v0=4(πr2v)A_0 v_0 = 4 (A v) \implies \pi r_0^2 v_0 = 4 (\pi r^2 v). Solving for vv: v=r02v04r2=(6.0)2(1.0)4(1.5)2=364×2.25=369.0=4.0 m/sv = \frac{r_0^2 v_0}{4 r^2} = \frac{(6.0)^2 (1.0)}{4 (1.5)^2} = \frac{36}{4 \times 2.25} = \frac{36}{9.0} = 4.0\text{ m/s}.

Loading workspace…