Resources

A vertical high-strength structural titanium rod of unstretched length L0=3.00 mL_0 = 3.00\text{ m} and cross-sectional area A=1.75×10−4 m2A = 1.75 \times 10^{-4}\text{ m}^2 has an elastic modulus of E=1.15×1011 PaE = 1.15 \times 10^{11}\text{ Pa} and an elastic proportional limit (yield stress) of σy=8.30×108 Pa\sigma_y = 8.30 \times 10^8\text{ Pa}. A load is gradually suspended from its lower end. Determine: (a) the maximum tensile load FcritF_{\text{crit}} that the rod can sustain before permanently departing from linear elastic behavior, (b) the elongation ΔLcrit\Delta L_{\text{crit}} at this exact threshold, and (c) the total elastic strain energy UelU_{\text{el}} stored within the entire volume of the rod at this critical boundary.

Answer and steps

Final answer

(a) Fcrit=1.45×105 NF_{\text{crit}} = 1.45 \times 10^5\text{ N}; (b) ΔLcrit=2.17 cm\Delta L_{\text{crit}} = 2.17\text{ cm}; (c) Uel=1.57×103 JU_{\text{el}} = 1.57 \times 10^3\text{ J}

Steps

Part (a): Maximum Tensile Load

Normal tensile stress σ\sigma is defined as the internal tensile force per unit cross-sectional area: σ=FA\sigma = \frac{F}{A}

The linear elastic limit represents the boundary beyond which deformation is no longer fully reversible or linear. To stay within this regime, the applied stress must not exceed the proportional limit (yield stress) σy\sigma_y. Therefore, the critical force FcritF_{\text{crit}} is: Fcrit=σy⋅AF_{\text{crit}} = \sigma_y \cdot A

Substitute the given values: Fcrit=(8.30×108 Pa)⋅(1.75×10−4 m2)=1.4525×105 N≈1.45×105 NF_{\text{crit}} = (8.30 \times 10^8\text{ Pa}) \cdot (1.75 \times 10^{-4}\text{ m}^2) = 1.4525 \times 10^5\text{ N} \approx 1.45 \times 10^5\text{ N}


Part (b): Critical Elongation

Hooke's Law for uniaxial stress relates stress to strain ε\varepsilon by Young's modulus EE: σ=E⋅ε=E⋅ΔLL0\sigma = E \cdot \varepsilon = E \cdot \frac{\Delta L}{L_0}

Rearranging to solve for the critical elongation ΔLcrit\Delta L_{\text{crit}} at the yield stress: ΔLcrit=σy⋅L0E\Delta L_{\text{crit}} = \frac{\sigma_y \cdot L_0}{E}

Substitute the values: ΔLcrit=(8.30×108 Pa)⋅(3.00 m)1.15×1011 Pa≈2.165×10−2 m≈2.17 cm\Delta L_{\text{crit}} = \frac{(8.30 \times 10^8\text{ Pa}) \cdot (3.00\text{ m})}{1.15 \times 10^{11}\text{ Pa}} \approx 2.165 \times 10^{-2}\text{ m} \approx 2.17\text{ cm}


Part (c): Total Elastic Strain Energy

The elastic strain energy UelU_{\text{el}} stored in a linearly elastic body equals the work done by the gradually applied load, which corresponds to the triangular area under the force-elongation (FF vs. ΔL\Delta L) curve: Uel=12FcritΔLcritU_{\text{el}} = \frac{1}{2} F_{\text{crit}} \Delta L_{\text{crit}}

Alternatively, using the strain energy density u=σy22Eu = \frac{\sigma_y^2}{2E} multiplied by the total volume V=A⋅L0V = A \cdot L_0: Uel=σy22E⋅(A⋅L0)U_{\text{el}} = \frac{\sigma_y^2}{2E} \cdot (A \cdot L_0)

Using the values obtained: Uel=12⋅(1.4525×105 N)⋅(2.1652×10−2 m)≈1.57×103 JU_{\text{el}} = \frac{1}{2} \cdot (1.4525 \times 10^5\text{ N}) \cdot (2.1652 \times 10^{-2}\text{ m}) \approx 1.57 \times 10^3\text{ J}

(Common Pitfall: Do not calculate work as simply W=F⋅ΔLW = F \cdot \Delta L. Because the load is applied gradually from zero up to FcritF_{\text{crit}}, the average force is 12Fcrit\frac{1}{2}F_{\text{crit}}, yielding the factor of 12\frac{1}{2}.)

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student forgets the factor of 1/2 in the elastic strain energy formula, treating the work as that done by a constant rather than a gradually applied linear load.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    Fcrit=σy⋅A  ⟹  Fcrit=(8.30×108)(1.75×10−4)=1.45×105 NF_{\text{crit}} = \sigma_y \cdot A \implies F_{\text{crit}} = (8.30 \times 10^8)(1.75 \times 10^{-4}) = 1.45 \times 10^5\text{ N}

  2. Step 2

    ΔLcrit=Fcrit⋅L0A⋅E  ⟹  ΔLcrit=(1.4525×105)(3.00)(1.75×10−4)(1.15×1011)=2.17×10−2 m\Delta L_{\text{crit}} = \frac{F_{\text{crit}} \cdot L_0}{A \cdot E} \implies \Delta L_{\text{crit}} = \frac{(1.4525 \times 10^5)(3.00)}{(1.75 \times 10^{-4})(1.15 \times 10^{11})} = 2.17 \times 10^{-2}\text{ m}

  3. Step 3

    Uel=Fcrit⋅ΔLcrit  ⟹  Uel=(1.4525×105 N)(2.1652×10−2 m)=3.14×103 JU_{\text{el}} = F_{\text{crit}} \cdot \Delta L_{\text{crit}} \implies U_{\text{el}} = (1.4525 \times 10^5\text{ N})(2.1652 \times 10^{-2}\text{ m}) = 3.14 \times 10^3\text{ J}

    Correct

    Uel=12FcritΔLcrit=12(1.4525×105 N)(2.1652×10−2 m)≈1.57×103 JU_{\text{el}} = \frac{1}{2} F_{\text{crit}} \Delta L_{\text{crit}} = \frac{1}{2}(1.4525 \times 10^5\text{ N})(2.1652 \times 10^{-2}\text{ m}) \approx 1.57 \times 10^3\text{ J}

    Because the tensile load increases linearly from 00 to FcritF_{\text{crit}} as the rod stretches, the strain energy equals the triangular area under the FF-versus-ΔL\Delta L curve, requiring a factor of 12\frac{1}{2}.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified the proportional yield stress formula to compute the critical tensile force.

You properly applied Hooke's law in uniaxial form to evaluate the critical elongation.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Missing $\frac{1}{2}$ factor in strain energy

You calculated work using W=F⋅ΔLW = F \cdot \Delta L as if the force were constant throughout the stretch, rather than averaging the gradually applied load.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing constant-force work with variable-force elastic potential energy (or the area under a linear force-displacement graph).

REASONING PATH
Your ACEpath teacher’s suggested approach
Gradual Loading vs. Constant Force
  • When an elastic body stretches under a load that increases linearly from 00 to FF, the average force is 12F\frac{1}{2}F, making the total work U=12FΔLU = \frac{1}{2} F \Delta L.

  • Always check whether the applied force is constant or linear with elongation before calculating work or strain energy.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Recall that elastic strain energy is the area under the linear force-displacement graph: Uel=12FcritΔLcritU_{\text{el}} = \frac{1}{2} F_{\text{crit}} \Delta L_{\text{crit}}.

  2. Substitute the previously calculated values: Uel=12(1.4525×105 N)(2.1652×10−2 m)U_{\text{el}} = \frac{1}{2} (1.4525 \times 10^5\text{ N})(2.1652 \times 10^{-2}\text{ m}).

  3. Evaluate the arithmetic: Uel≈1.57×103 JU_{\text{el}} \approx 1.57 \times 10^3\text{ J}.

Final answer

1.57×103 J1.57 \times 10^3\text{ J}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the geometric interpretation of strain energy as the triangular area beneath a stress-strain or force-elongation curve.

  • Practice calculating strain energy density u=12σε=σ22Eu = \frac{1}{2} \sigma \varepsilon = \frac{\sigma^2}{2E} and multiplying by volume VV as an alternative check.

OverviewACEpath Teacher's Diagnosis

02 The student inverts the elastic modulus formula when calculating elongation, multiplying by E rather than dividing by it.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    Fcrit=σy⋅A  ⟹  Fcrit=(8.30×108)(1.75×10−4)=1.45×105 NF_{\text{crit}} = \sigma_y \cdot A \implies F_{\text{crit}} = (8.30 \times 10^8)(1.75 \times 10^{-4}) = 1.45 \times 10^5\text{ N}

  2. Step 2

    ΔLcrit=σy⋅EL0  ⟹  ΔLcrit=(8.30×108)(1.15×1011)3.00=3.18×1019 m\Delta L_{\text{crit}} = \frac{\sigma_y \cdot E}{L_0} \implies \Delta L_{\text{crit}} = \frac{(8.30 \times 10^8)(1.15 \times 10^{11})}{3.00} = 3.18 \times 10^{19}\text{ m}

    Correct

    ΔLcrit=σy⋅L0E=(8.30×108 Pa)(3.00 m)1.15×1011 Pa≈2.17×10−2 m\Delta L_{\text{crit}} = \frac{\sigma_y \cdot L_0}{E} = \frac{(8.30 \times 10^8\text{ Pa})(3.00\text{ m})}{1.15 \times 10^{11}\text{ Pa}} \approx 2.17 \times 10^{-2}\text{ m}

    From Hooke's law, σ=Eε=EΔLL0\sigma = E \varepsilon = E \frac{\Delta L}{L_0}. Solving for elongation requires dividing by Young's modulus EE and multiplying by L0L_0, not multiplying by EE and dividing by L0L_0.

  3. Step 3

    Uel=12⋅Fcrit⋅ΔLcrit  ⟹  Uel=(12)(1.4525×105)(3.1817×1019)=2.31×1024 JU_{\text{el}} = \frac{1}{2} \cdot F_{\text{crit}} \cdot \Delta L_{\text{crit}} \implies U_{\text{el}} = \left(\frac{1}{2}\right)(1.4525 \times 10^5)(3.1817 \times 10^{19}) = 2.31 \times 10^{24}\text{ J}

    Correct

    Uel=12FcritΔLcrit=12(1.4525×105 N)(2.165×10−2 m)≈1.57×103 JU_{\text{el}} = \frac{1}{2} F_{\text{crit}} \Delta L_{\text{crit}} = \frac{1}{2}(1.4525 \times 10^5\text{ N})(2.165 \times 10^{-2}\text{ m}) \approx 1.57 \times 10^3\text{ J}

    Your formula for stored elastic strain energy under a gradually applied load is correct, but your numerical result inherited the incorrect value of ΔLcrit\Delta L_{\text{crit}}.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly applied the definition of normal tensile stress to find the critical load.

You used the correct triangular work formula for elastic strain energy under a gradual load.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Formula inversion in Hooke's law

You swapped the positions of Young's modulus EE and unstretched length L0L_0 when isolating ΔL\Delta L.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Confusing how stiffness relates to elongation: a stiffer material (larger EE) resists stretching and must decrease elongation for a given stress, meaning EE must be in the denominator.

REASONING PATH
Your ACEpath teacher’s suggested approach
Stiffness Intuition Check
  • Higher elastic modulus EE means greater stiffness and smaller elongation for the same applied stress.

  • Always check that EE appears in the denominator when solving for elongation: ΔL=σL0E\Delta L = \frac{\sigma L_0}{E}.

Dimensional & Reality Sanity Check
  • A rod of length 3 m3\text{ m} cannot stretch by astronomical distances like 1019 m10^{19}\text{ m} under elastic deformation.

  • Check units: Pa⋅mPa=m\frac{\text{Pa} \cdot \text{m}}{\text{Pa}} = \text{m}, whereas Pa⋅Pam=Pa2m≠m\frac{\text{Pa} \cdot \text{Pa}}{\text{m}} = \frac{\text{Pa}^2}{\text{m}} \neq \text{m}.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Set up Hooke's law: σy=E(ΔLcritL0)\sigma_y = E \left(\frac{\Delta L_{\text{crit}}}{L_0}\right).

  2. Isolate ΔLcrit\Delta L_{\text{crit}} correctly: ΔLcrit=σyL0E=(8.30×108 Pa)(3.00 m)1.15×1011 Pa≈2.165×10−2 m=2.17 cm\Delta L_{\text{crit}} = \frac{\sigma_y L_0}{E} = \frac{(8.30 \times 10^8\text{ Pa})(3.00\text{ m})}{1.15 \times 10^{11}\text{ Pa}} \approx 2.165 \times 10^{-2}\text{ m} = 2.17\text{ cm}.

  3. Substitute the corrected elongation into the strain energy formula: Uel=12FcritΔLcrit=12(1.4525×105 N)(2.165×10−2 m)≈1.57×103 JU_{\text{el}} = \frac{1}{2} F_{\text{crit}} \Delta L_{\text{crit}} = \frac{1}{2}(1.4525 \times 10^5\text{ N})(2.165 \times 10^{-2}\text{ m}) \approx 1.57 \times 10^3\text{ J}.

Final answer

(a) Fcrit=1.45×105 NF_{\text{crit}} = 1.45 \times 10^5\text{ N}; (b) ΔLcrit=2.17 cm\Delta L_{\text{crit}} = 2.17\text{ cm}; (c) Uel=1.57×103 JU_{\text{el}} = 1.57 \times 10^3\text{ J}

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice isolating variables from σ=E⋅ΔLL0\sigma = E \cdot \frac{\Delta L}{L_0} step by step before substituting numerical values.

  • Perform a quick order-of-magnitude and dimensional check whenever calculating elastic deformations.

OverviewACEpath Teacher's Diagnosis

03 The student calculates strain energy density per unit volume instead of integrating over the entire volume of the rod.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Partially correct
  1. Step 1

    Fcrit=σy⋅A  ⟹  Fcrit=(8.30×108)(1.75×10−4)  ⟹  Fcrit=1.45×105 NF_{\text{crit}} = \sigma_y \cdot A \implies F_{\text{crit}} = (8.30 \times 10^8)(1.75 \times 10^{-4}) \implies F_{\text{crit}} = 1.45 \times 10^5\text{ N}

  2. Step 2

    ΔLcrit=σy⋅L0E  ⟹  ΔLcrit=(8.30×108)(3.00)1.15×1011  ⟹  ΔLcrit=2.17×10−2 m\Delta L_{\text{crit}} = \frac{\sigma_y \cdot L_0}{E} \implies \Delta L_{\text{crit}} = \frac{(8.30 \times 10^8)(3.00)}{1.15 \times 10^{11}} \implies \Delta L_{\text{crit}} = 2.17 \times 10^{-2}\text{ m}

  3. Step 3

    Uel=12⋅σy2E  ⟹  Uel=12⋅((8.30×108)21.15×1011)  ⟹  Uel=2.99×106 JU_{\text{el}} = \frac{1}{2} \cdot \frac{\sigma_y^2}{E} \implies U_{\text{el}} = \frac{1}{2} \cdot \left(\frac{(8.30 \times 10^8)^2}{1.15 \times 10^{11}}\right) \implies U_{\text{el}} = 2.99 \times 10^6\text{ J}

    Correct

    Uel=σy22E⋅V=σy22E(AL0)=(2.995×106 J/m3)(1.75×10−4 m2)(3.00 m)≈1.57×103 JU_{\text{el}} = \frac{\sigma_y^2}{2E} \cdot V = \frac{\sigma_y^2}{2E} (A L_0) = (2.995 \times 10^6\text{ J/m}^3)(1.75 \times 10^{-4}\text{ m}^2)(3.00\text{ m}) \approx 1.57 \times 10^3\text{ J}

    You evaluated u=σy22Eu = \frac{\sigma_y^2}{2E}, which is the strain energy density (energy per unit volume in J/m3\text{J/m}^3), but you omitted multiplying by the rod's volume V=AL0V = A L_0 (or using Uel=12FcritΔLcritU_{\text{el}} = \frac{1}{2} F_{\text{crit}} \Delta L_{\text{crit}}) to find the total stored energy.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly used the definition of stress to calculate the critical tensile force.

You rearranged Hooke's law accurately to find the elongation at the yield point.

You correctly recalled the quadratic stress formula for elastic strain energy density.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Energy density vs. total energy confusion

none

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You conflated strain energy density u=UV=σ22Eu = \frac{U}{V} = \frac{\sigma^2}{2E} with the total elastic strain energy Uel=u⋅VU_{\text{el}} = u \cdot V.

REASONING PATH
Your ACEpath teacher’s suggested approach
Check physical units of energy versus energy density
  • Total strain energy UelU_{\text{el}} has units of Joules (J\text{J}), whereas strain energy density uu has units of J/m3\text{J/m}^3 (or Pa\text{Pa}).

  • Always multiply the energy density uu by the total material volume V=AL0V = A L_0, or alternatively compute work directly as Uel=12FΔLU_{\text{el}} = \frac{1}{2} F \Delta L.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Multiply your computed energy density u=σy22E=2.995×106 J/m3u = \frac{\sigma_y^2}{2E} = 2.995 \times 10^6\text{ J/m}^3 by the volume V=A⋅L0V = A \cdot L_0.

  2. Calculate volume: V=(1.75×10−4 m2)(3.00 m)=5.25×10−4 m3V = (1.75 \times 10^{-4}\text{ m}^2)(3.00\text{ m}) = 5.25 \times 10^{-4}\text{ m}^3.

  3. Compute total energy: Uel=(2.995×106 J/m3)(5.25×10−4 m3)≈1.57×103 JU_{\text{el}} = (2.995 \times 10^6\text{ J/m}^3)(5.25 \times 10^{-4}\text{ m}^3) \approx 1.57 \times 10^3\text{ J}.

Final answer

Uel≈1.57×103 JU_{\text{el}} \approx 1.57 \times 10^3\text{ J}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the distinction between intensive properties (energy density uu) and extensive properties (total energy UU).

  • Verify your formula units by dimensional analysis before substituting values: Pa2Pa=Pa=J/m3\frac{\text{Pa}^2}{\text{Pa}} = \text{Pa} = \text{J/m}^3, which indicates energy per volume rather than total energy.

  • Practice using both the force-displacement formulation (U=12FΔLU = \frac{1}{2} F \Delta L) and the stress-strain formulation (U=uVU = u V) to double-check your answers.

Lock it in

Similar question

01

A steel wire is stretched elastically by a gradually applied load until the force reaches 4.00×103 N4.00 \times 10^3\text{ N}, causing an elongation of 1.50 mm1.50\text{ mm}. Calculate the elastic strain energy stored in the wire.

Answer

U=12FΔL=12(4.00×103 N)(1.50×10−3 m)=3.00 JU = \frac{1}{2} F \Delta L = \frac{1}{2}(4.00 \times 10^3\text{ N})(1.50 \times 10^{-3}\text{ m}) = 3.00\text{ J}.

02

A cylindrical copper rod of volume V=2.50×10−4 m3V = 2.50 \times 10^{-4}\text{ m}^3 and Young's modulus E=1.10×1011 PaE = 1.10 \times 10^{11}\text{ Pa} is subjected to a uniform tensile stress of σ=2.20×108 Pa\sigma = 2.20 \times 10^8\text{ Pa} within its elastic limit. Find the total elastic strain energy stored in the rod.

Answer

Using energy density u=σ22Eu = \frac{\sigma^2}{2E}, U=u⋅V=(2.20×108 Pa)22(1.10×1011 Pa)×(2.50×10−4 m3)=(2.20×105 J/m3)(2.50×10−4 m3)=55.0 JU = u \cdot V = \frac{(2.20 \times 10^8\text{ Pa})^2}{2(1.10 \times 10^{11}\text{ Pa})} \times (2.50 \times 10^{-4}\text{ m}^3) = (2.20 \times 10^5\text{ J/m}^3)(2.50 \times 10^{-4}\text{ m}^3) = 55.0\text{ J}.

03

Two identical elastic rods, Rod A and Rod B, have identical cross-sections and lengths. Rod A is stretched by ΔL\Delta L under a gradually increasing tension FF. Rod B is stretched twice as far (2ΔL2\Delta L) within the linear elastic regime. How many times more elastic strain energy is stored in Rod B than in Rod A?

Answer

Since U=12k(ΔL)2U = \frac{1}{2} k (\Delta L)^2, strain energy scales quadratically with elongation: UB/UA=(2ΔL/ΔL)2=4U_B / U_A = (2\Delta L / \Delta L)^2 = 4. Rod B stores 44 times as much energy.

Loading workspace…