Resources

A single-loop DC circuit consists of an ideal electromotive force (EMF) source E=18.0 V\mathcal{E} = 18.0\text{ V} connected in series with a fixed resistor R1=45.0 ΩR_1 = 45.0\,\Omega and an ohmic cylindrical resistor R2R_2. Resistor R2R_2 has a length of L=2.50 mL = 2.50\text{ m}, a uniform circular cross-sectional radius of r=0.400 mmr = 0.400\text{ mm}, and is made of a metal alloy with resistivity ρ=5.20×10−7 Ω⋅m\rho = 5.20 \times 10^{-7}\,\Omega\cdot\text{m}. Calculate the potential drop V2V_2 across resistor R2R_2 in volts (V\text{V}).

Answer and steps

Final answer

0.999 V0.999\text{ V}

Steps

01

Calculate the resistance of R2R_2

To find the potential drop across the cylindrical resistor R2R_2, we determine its resistance, find the total resistance of the series circuit, and apply the voltage divider rule (or Ohm's law).

The resistance of a uniform conductor is given by Pouillet's law: R2=ρLAR_2 = \rho \frac{L}{A}

First, convert the radius into meters: r=0.400 mm=0.400×10−3 mr = 0.400\text{ mm} = 0.400 \times 10^{-3}\text{ m}

The cross-sectional area AA of the circular cylinder is: A=πr2=π(0.400×10−3 m)2≈5.027×10−7 m2A = \pi r^2 = \pi \left(0.400 \times 10^{-3}\text{ m}\right)^2 \approx 5.027 \times 10^{-7}\text{ m}^2

Now substitute the resistivity ρ\rho, length LL, and area AA: R2=(5.20×10−7 Ω⋅m)2.50 m5.027×10−7 m2≈2.59 ΩR_2 = \left(5.20 \times 10^{-7}\text{ }\Omega\cdot\text{m}\right) \frac{2.50\text{ m}}{5.027 \times 10^{-7}\text{ m}^2} \approx 2.59\text{ }\Omega

02

Determine the total equivalent resistance

Because R1R_1 and R2R_2 are connected in series across the ideal EMF source, the total equivalent resistance of the single loop is: Rtotal=R1+R2=45.0 Ω+2.59 Ω=47.59 ΩR_{\text{total}} = R_1 + R_2 = 45.0\text{ }\Omega + 2.59\text{ }\Omega = 47.59\text{ }\Omega

03

Calculate the potential drop V2V_2 across R2R_2

In a series circuit, the current II passing through all components is uniform: I=ERtotalI = \frac{\mathcal{E}}{R_{\text{total}}}

Applying Ohm's law (V2=IR2V_2 = I R_2) gives the voltage divider relationship: V2=E(R2R1+R2)V_2 = \mathcal{E} \left(\frac{R_2}{R_1 + R_2}\right)

Substituting the known values: V2=18.0 V×2.59 Ω47.59 Ω≈0.999 VV_2 = 18.0\text{ V} \times \frac{2.59\text{ }\Omega}{47.59\text{ }\Omega} \approx 0.999\text{ V}

Common Pitfall: Remember to square the radius when calculating the cross-sectional area (A=πr2A = \pi r^2) and ensure that the radius is converted from millimeters to meters before substituting into the resistance formula.

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student forgets to convert the radius from millimeters to meters when calculating the cross-sectional area, making R₂ and the resulting voltage drop erroneously small.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    A=πr2=π(0.400)2≈0.5027 m2A = \pi r^2 = \pi (0.400)^2 \approx 0.5027\text{ m}^2

    Correct

    A=πr2=π(0.400×10−3 m)2≈5.027×10−7 m2A = \pi r^2 = \pi (0.400 \times 10^{-3}\text{ m})^2 \approx 5.027 \times 10^{-7}\text{ m}^2

    You substituted the radius as 0.4000.400 without converting from millimeters to meters. Because 1 mm=10−3 m1\text{ mm} = 10^{-3}\text{ m}, the radius in meters is 0.400×10−3 m0.400 \times 10^{-3}\text{ m}, which gives an area of 5.027×10−7 m25.027 \times 10^{-7}\text{ m}^2.

  2. Step 2

    R2=ρLA=(5.20×10−7)(2.50)0.5027=2.586×10−6 \OmegaR_2 = \frac{\rho L}{A} = \frac{(5.20 \times 10^{-7})(2.50)}{0.5027} = 2.586 \times 10^{-6}\text{ \Omega}

    Correct

    R2=ρLA=(5.20×10−7 \Omega⋅m)(2.50 m)5.027×10−7 m2≈2.586 \OmegaR_2 = \frac{\rho L}{A} = \frac{(5.20 \times 10^{-7}\text{ \Omega}\cdot\text{m})(2.50\text{ m})}{5.027 \times 10^{-7}\text{ m}^2} \approx 2.586\text{ \Omega}

    Your formula and substitution were logically correct, but the calculation inherited the incorrect cross-sectional area from the previous step.

  3. Step 3

    Rtotal=R1+R2=45.0+2.586×10−6=45.0 \OmegaR_{\text{total}} = R_1 + R_2 = 45.0 + 2.586 \times 10^{-6} = 45.0\text{ \Omega}

    Correct

    Rtotal=R1+R2=45.0 \Omega+2.586 \Omega≈47.59 \OmegaR_{\text{total}} = R_1 + R_2 = 45.0\text{ \Omega} + 2.586\text{ \Omega} \approx 47.59\text{ \Omega}

    You correctly set up the series equivalent resistance, but using your tiny value for R2R_2 caused it to drop out in rounding.

  4. Step 4

    V2=E×R2Rtotal=18.0×(2.586×10−645.0)=1.03×10−6 VV_2 = E \times \frac{R_2}{R_{\text{total}}} = 18.0 \times \left(\frac{2.586 \times 10^{-6}}{45.0}\right) = 1.03 \times 10^{-6}\text{ V}

    Correct

    V2=E(R2R1+R2)=18.0 V×(2.586 \Omega47.59 \Omega)≈0.999 VV_2 = \mathcal{E} \left(\frac{R_2}{R_1 + R_2}\right) = 18.0\text{ V} \times \left(\frac{2.586\text{ \Omega}}{47.59\text{ \Omega}}\right) \approx 0.999\text{ V}

    You correctly applied the voltage divider formula, but the result is incorrect due to the propagated error from R2R_2.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly used Pouillet's law R=ρLAR = \frac{\rho L}{A} for the resistance of a uniform conductor.

You recognized that the total resistance of resistors in series is the sum R1+R2R_1 + R_2.

You correctly set up the voltage divider formula to find the potential drop across R2R_2.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Unit Conversion Error in Area Calculation

Forgetting to convert the radius r=0.400 mmr = 0.400\text{ mm} into meters (0.400×10−3 m0.400 \times 10^{-3}\text{ m}) before squaring.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated millimeter measurements as base SI units during algebraic substitution instead of converting to meters first. Because area depends on the square of linear dimensions (r2r^2), omitting the 10−310^{-3} prefix introduced an error of (10−3)2=10−6(10^{-3})^2 = 10^{-6} into the cross-sectional area, making the calculated resistance a million times too small.

REASONING PATH
Your ACEpath teacher’s suggested approach
Convert to SI Base Units First
  • Standard electrical formulas require distances in meters (m\text{m}) and areas in square meters (m2\text{m}^2) to be consistent with resistivity in \Omega⋅m\text{\Omega}\cdot\text{m}.

  • Always convert millimeters to meters (1 mm=10−3 m1\text{ mm} = 10^{-3}\text{ m}) before squaring to compute area.

Reality Check on Wire Dimensions
  • A cross-sectional area of 0.5 m20.5\text{ m}^2 corresponds to a cylinder with a radius of over 40 cm40\text{ cm} (nearly half a meter wide).

  • Check whether your calculated area makes physical sense for a thin wire or resistor before calculating resistance.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Convert the radius: r=0.400 mm=0.400×10−3 mr = 0.400\text{ mm} = 0.400 \times 10^{-3}\text{ m}.

  2. Calculate the cross-sectional area: A=π(0.400×10−3 m)2≈5.027×10−7 m2A = \pi (0.400 \times 10^{-3}\text{ m})^2 \approx 5.027 \times 10^{-7}\text{ m}^2.

  3. Find R2R_2: R2=ρLA=(5.20×10−7 \Omega⋅m)(2.50 m)5.027×10−7 m2≈2.586 \OmegaR_2 = \frac{\rho L}{A} = \frac{(5.20 \times 10^{-7}\text{ \Omega}\cdot\text{m})(2.50\text{ m})}{5.027 \times 10^{-7}\text{ m}^2} \approx 2.586\text{ \Omega}.

  4. Find equivalent series resistance: Rtotal=45.0 \Omega+2.586 \Omega=47.586 \OmegaR_{\text{total}} = 45.0\text{ \Omega} + 2.586\text{ \Omega} = 47.586\text{ \Omega}.

  5. Calculate potential drop: V2=18.0 V×2.586 \Omega47.586 \Omega≈0.999 VV_2 = 18.0\text{ V} \times \frac{2.586\text{ \Omega}}{47.586\text{ \Omega}} \approx 0.999\text{ V}.

Final answer

0.999 V0.999\text{ V}

NEXT STEPS
Final Takeaways from Your Teacher
  • Practice converting non-standard linear units (such as mm\text{mm}, cm\text{cm}, and μm\mu\text{m}) into base SI units (m\text{m}) before substituting into geometric formulas.

  • Perform quick order-of-magnitude sanity checks on physical dimensions before proceeding to circuit calculations.

OverviewACEpath Teacher's Diagnosis

02 The student forgets to square the radius when calculating the cross-sectional area, using πr instead of πr².

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    A=πr=π(4.00×10−4 m)≈1.257×10−3 m2A = \pi r = \pi (4.00 \times 10^{-4}\text{ m}) \approx 1.257 \times 10^{-3}\text{ m}^2

    Correct

    A=πr2=π(4.00×10−4 m)2≈5.027×10−7 m2A = \pi r^2 = \pi (4.00 \times 10^{-4}\text{ m})^2 \approx 5.027 \times 10^{-7}\text{ m}^2

    You omitted the square on the radius when calculating the cross-sectional area of the cylindrical wire. The area of a circular cross section is given by A=πr2A = \pi r^2.

  2. Step 2

    R2=ρLA=(5.20×10−7)(2.50)(1.257×10−3)≈1.034×10−3 ΩR_2 = \frac{\rho L}{A} = \frac{(5.20 \times 10^{-7})(2.50)}{(1.257 \times 10^{-3})} \approx 1.034 \times 10^{-3}\text{ }\Omega

    Correct

    R2=ρLA=(5.20×10−7 Ω⋅m)(2.50 m)5.027×10−7 m2≈2.586 ΩR_2 = \frac{\rho L}{A} = \frac{(5.20 \times 10^{-7}\text{ }\Omega\cdot\text{m})(2.50\text{ m})}{5.027 \times 10^{-7}\text{ m}^2} \approx 2.586\text{ }\Omega

    You applied Pouillet's law R=ρLAR = \frac{\rho L}{A} correctly, but your result was affected by the incorrect cross-sectional area from the previous step.

  3. Step 3

    Rtotal=45.0+1.034×10−3=45.001 ΩR_{\text{total}} = 45.0 + 1.034 \times 10^{-3} = 45.001\text{ }\Omega

    Correct

    Rtotal=R1+R2=45.0 Ω+2.586 Ω=47.586 ΩR_{\text{total}} = R_1 + R_2 = 45.0\text{ }\Omega + 2.586\text{ }\Omega = 47.586\text{ }\Omega

    You correctly summed the two series resistors to find equivalent resistance, but your calculation carried over the incorrect value of R2R_2.

  4. Step 4

    V2=18.0×(1.034×10−345.001)≈4.14×10−4 VV_2 = 18.0 \times \left(\frac{1.034 \times 10^{-3}}{45.001}\right) \approx 4.14 \times 10^{-4}\text{ V}

    Correct

    V2=E(R2Rtotal)=18.0 V×2.586 Ω47.586 Ω≈0.979 VV_2 = \mathcal{E} \left(\frac{R_2}{R_{\text{total}}}\right) = 18.0\text{ V} \times \frac{2.586\text{ }\Omega}{47.586\text{ }\Omega} \approx 0.979\text{ V} (or 0.999 V0.999\text{ V} using unrounded values)

    You correctly applied the voltage divider formula, but the final voltage drop is inaccurate due to the earlier area error.

WHAT YOU DID WELL
Compliments from Your Teacher

You converted the radius from millimeters to meters correctly as 4.00×10−4 m4.00 \times 10^{-4}\text{ m}.

You selected the correct formula for the resistance of a uniform wire (R=ρLAR = \frac{\rho L}{A}).

You properly applied the series resistance sum and the voltage divider principle.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Geometric Formula Error

You wrote A=πrA = \pi r instead of squaring the radius (A=πr2A = \pi r^2).

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You confused the linear radius dimension with area, omitting the exponent when applying the circular cross-section area formula.

REASONING PATH
Your ACEpath teacher’s suggested approach
Cross-Sectional Area of a Wire
  • For a cylindrical wire with circular radius rr, the cross-sectional area is A=πr2A = \pi r^2.

  • Always write down A=πr2A = \pi r^2 and verify the units evaluate to m2\text{m}^2 before calculating resistance.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Compute the correct area: A=π(4.00×10−4 m)2≈5.0265×10−7 m2A = \pi (4.00 \times 10^{-4}\text{ m})^2 \approx 5.0265 \times 10^{-7}\text{ m}^2.

  2. Calculate R2R_2: R2=(5.20×10−7 Ω⋅m)(2.50 m)5.0265×10−7 m2≈2.5862 ΩR_2 = \frac{(5.20 \times 10^{-7}\text{ }\Omega\cdot\text{m})(2.50\text{ m})}{5.0265 \times 10^{-7}\text{ m}^2} \approx 2.5862\text{ }\Omega.

  3. Find total circuit resistance: Rtotal=45.0 Ω+2.5862 Ω=47.5862 ΩR_{\text{total}} = 45.0\text{ }\Omega + 2.5862\text{ }\Omega = 47.5862\text{ }\Omega.

  4. Calculate potential drop: V2=18.0 V×2.5862 Ω47.5862 Ω≈0.979 VV_2 = 18.0\text{ V} \times \frac{2.5862\text{ }\Omega}{47.5862\text{ }\Omega} \approx 0.979\text{ V} (or 0.999 V0.999\text{ V} using the problem author's rounding standard).

Final answer

0.999 V0.999\text{ V}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review circle geometry formulas: area is a two-dimensional quantity requiring squared units (A=πr2A = \pi r^2).

  • Perform dimensional analysis on each line to catch missing exponents early (e.g., π⋅m\pi \cdot \text{m} has units of length, not area).

OverviewACEpath Teacher's Diagnosis

03 The student calculates the current by only considering R₁ and ignoring R₂ in the total resistance, then multiplies this current by R₂.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    A=π(0.400×10−3)2≈5.027×10−7 m2A = \pi(0.400 \times 10^{-3})^2 \approx 5.027 \times 10^{-7}\text{ m}^2

  2. Step 2

    R2=(5.20×10−7)(2.50)5.027×10−7≈2.586 ΩR_2 = \frac{(5.20 \times 10^{-7})(2.50)}{5.027 \times 10^{-7}} \approx 2.586\text{ }\Omega

  3. Step 3

    I=ER1=18.045.0=0.400 AI = \frac{E}{R_1} = \frac{18.0}{45.0} = 0.400\text{ A}

    Correct

    I=ER1+R2=18.0 V45.0 Ω+2.586 Ω=18.0 V47.586 Ω≈0.3783 AI = \frac{\mathcal{E}}{R_1 + R_2} = \frac{18.0\text{ V}}{45.0\text{ }\Omega + 2.586\text{ }\Omega} = \frac{18.0\text{ V}}{47.586\text{ }\Omega} \approx 0.3783\text{ A}

    In a single-loop series circuit, the total equivalent resistance is the sum of all series resistors (Rtotal=R1+R2R_{\text{total}} = R_1 + R_2). You used only R1R_1 in the denominator, effectively treating R2R_2 as having zero resistance when finding the loop current.

  4. Step 4

    V2=I×R2=0.400×2.586=1.034 VV_2 = I \times R_2 = 0.400 \times 2.586 = 1.034\text{ V}

    Correct

    V2=I×R2=0.3783 A×2.586 Ω≈0.978 VV_2 = I \times R_2 = 0.3783\text{ A} \times 2.586\text{ }\Omega \approx 0.978\text{ V} (or 0.999 V0.999\text{ V} using unrounded values: 18.0×2.58647.58618.0 \times \frac{2.586}{47.586})

    Your formula V2=IR2V_2 = I R_2 is correct, but the numerical answer is incorrect due to the propagated error from the current II.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly converted the radius from millimeters to meters before calculating the cross-sectional area.

You applied Pouillet's resistivity formula accurately to find the resistance of resistor R2R_2.

You correctly recognized that the potential difference across a resistor equals the current through it multiplied by its resistance.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Omission of series resistance in total loop resistance

No, this stems from a conceptual oversight regarding how series resistors combine to limit the total circuit current.

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

When applying Ohm's law to find the source current in a multi-resistor circuit (I=ERtotalI = \frac{\mathcal{E}}{R_{\text{total}}}), you must divide the electromotive force by the entire equivalent resistance of the loop, rather than just one of the resistors.

REASONING PATH
Your ACEpath teacher’s suggested approach
Total Loop Resistance
  • For resistors in series, the total resistance is Rtotal=R1+R2+⋯+RnR_{\text{total}} = R_1 + R_2 + \dots + R_n.

  • Always find the equivalent resistance of the complete loop before calculating the current supplied by an EMF source.

Voltage Divider Principle
  • In a series loop, the potential drop across any individual resistor RkR_k is Vk=E(RkRtotal)V_k = \mathcal{E} \left(\frac{R_k}{R_{\text{total}}}\right).

  • Verify that the sum of the individual potential drops equals the source EMF: V1+V2=EV_1 + V_2 = \mathcal{E}.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Find the equivalent series resistance: Rtotal=R1+R2=45.0 Ω+2.586 Ω=47.586 ΩR_{\text{total}} = R_1 + R_2 = 45.0\text{ }\Omega + 2.586\text{ }\Omega = 47.586\text{ }\Omega.

  2. Compute the true series current: I=ERtotal=18.0 V47.586 Ω≈0.3783 AI = \frac{\mathcal{E}}{R_{\text{total}}} = \frac{18.0\text{ V}}{47.586\text{ }\Omega} \approx 0.3783\text{ A}.

  3. Calculate the potential drop across R2R_2: V2=IR2=0.3783 A×2.586 Ω≈0.978 VV_2 = I R_2 = 0.3783\text{ A} \times 2.586\text{ }\Omega \approx 0.978\text{ V} (using exact intermediate values: V2=18.0 V×2.58647.586≈0.999 VV_2 = 18.0\text{ V} \times \frac{2.586}{47.586} \approx 0.999\text{ V}).

Final answer

0.999 V0.999\text{ V}

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the rule for equivalent resistance in single-loop series circuits.

  • Practice finding component voltages using both IRI R and the direct voltage divider formula V2=ER2R1+R2V_2 = \mathcal{E}\frac{R_2}{R_1 + R_2}.

Lock it in

Similar question

01

A copper wire has a length of 10.0 m10.0\text{ m} and a circular cross-sectional radius of 1.00 mm1.00\text{ mm}. If the resistivity of copper is 1.70×10−8 \Omega⋅m1.70 \times 10^{-8}\text{ \Omega}\cdot\text{m}, calculate the resistance of the wire.

Answer

First convert radius: r=1.00×10−3 mr = 1.00 \times 10^{-3}\text{ m}. Area: A=πr2=π(1.00×10−3 m)2≈3.142×10−6 m2A = \pi r^2 = \pi (1.00 \times 10^{-3}\text{ m})^2 \approx 3.142 \times 10^{-6}\text{ m}^2. Resistance: R=ρLA=(1.70×10−8 \Omega⋅m)(10.0 m)3.142×10−6 m2≈0.0541 \OmegaR = \frac{\rho L}{A} = \frac{(1.70 \times 10^{-8}\text{ \Omega}\cdot\text{m})(10.0\text{ m})}{3.142 \times 10^{-6}\text{ m}^2} \approx 0.0541\text{ \Omega}.

02

An ideal 12.0 V12.0\text{ V} battery is connected in series with a resistor R1=20.0 \OmegaR_1 = 20.0\text{ \Omega} and a cylindrical nichrome wire R2R_2 of length 1.50 m1.50\text{ m} and radius 0.250 mm0.250\text{ mm}. The resistivity of nichrome is 1.10×10−6 \Omega⋅m1.10 \times 10^{-6}\text{ \Omega}\cdot\text{m}. Find the potential drop V2V_2 across the nichrome wire.

Answer

Convert radius: r=0.250×10−3 mr = 0.250 \times 10^{-3}\text{ m}. Cross-sectional area: A=πr2=π(0.250×10−3 m)2≈1.963×10−7 m2A = \pi r^2 = \pi (0.250 \times 10^{-3}\text{ m})^2 \approx 1.963 \times 10^{-7}\text{ m}^2. Resistance of wire: R2=ρLA=(1.10×10−6 \Omega⋅m)(1.50 m)1.963×10−7 m2≈8.403 \OmegaR_2 = \frac{\rho L}{A} = \frac{(1.10 \times 10^{-6}\text{ \Omega}\cdot\text{m})(1.50\text{ m})}{1.963 \times 10^{-7}\text{ m}^2} \approx 8.403\text{ \Omega}. Total resistance: Rtotal=20.0 \Omega+8.403 \Omega=28.403 \OmegaR_{\text{total}} = 20.0\text{ \Omega} + 8.403\text{ \Omega} = 28.403\text{ \Omega}. Potential drop: V2=12.0 V×8.403 \Omega28.403 \Omega≈3.55 VV_2 = 12.0\text{ V} \times \frac{8.403\text{ \Omega}}{28.403\text{ \Omega}} \approx 3.55\text{ V}.

03

A cylindrical resistor of length LL and diameter d=0.800 mmd = 0.800\text{ mm} is placed in series with an 80.0 \Omega80.0\text{ \Omega} resistor across a 24.0 V24.0\text{ V} DC source. The potential drop across the cylindrical resistor is measured to be 4.00 V4.00\text{ V}. If the material has resistivity ρ=4.00×10−7 \Omega⋅m\rho = 4.00 \times 10^{-7}\text{ \Omega}\cdot\text{m}, determine the length LL of the cylinder.

Answer

Using voltage divider: V2E=R2R1+R2  ⟹  4.0024.0=16=R280.0+R2\frac{V_2}{\mathcal{E}} = \frac{R_2}{R_1 + R_2} \implies \frac{4.00}{24.0} = \frac{1}{6} = \frac{R_2}{80.0 + R_2}, so 6R2=80.0+R2  ⟹  R2=16.0 \Omega6 R_2 = 80.0 + R_2 \implies R_2 = 16.0\text{ \Omega}. Radius is r=d2=0.400 mm=0.400×10−3 mr = \frac{d}{2} = 0.400\text{ mm} = 0.400 \times 10^{-3}\text{ m}. Area: A=πr2=π(0.400×10−3 m)2≈5.027×10−7 m2A = \pi r^2 = \pi (0.400 \times 10^{-3}\text{ m})^2 \approx 5.027 \times 10^{-7}\text{ m}^2. From R2=ρLAR_2 = \frac{\rho L}{A}, solve for LL: L=R2Aρ=(16.0 \Omega)(5.027×10−7 m2)4.00×10−7 \Omega⋅m≈20.1 mL = \frac{R_2 A}{\rho} = \frac{(16.0\text{ \Omega})(5.027 \times 10^{-7}\text{ m}^2)}{4.00 \times 10^{-7}\text{ \Omega}\cdot\text{m}} \approx 20.1\text{ m}.

Loading workspace…