Resources

A spherical temperature sensor of radius R=2.00 mmR = 2.00\text{ mm} is placed in a high-temperature rarefied gas inside an ultra-high vacuum chamber with walls held at Tsurr=300 KT_{\text{surr}} = 300\text{ K}. In this environment, natural convection is negligible, but radiation is active with emissivity ε=0.850\varepsilon = 0.850. As the surrounding rarefied gas pressure approaches the extreme low-pressure limit, the gas thermal conductivity approaches kg=0.0150 W/(m⋅K)k_g = 0.0150\text{ W}/(\text{m}\cdot\text{K}) and heat transfers through a stationary spherical gas sheath of outer radius router→∞r_{\text{outer}} \to \infty surrounding the sensor. Using the asymptotic conduction limit for an isolated sphere in an infinite medium, the conduction shape factor yields a thermal resistance of Rcond,∞=14πkgRR_{\text{cond},\infty} = \frac{1}{4\pi k_g R}. If an internal electrical circuit continuously deposits Q˙=0.250 W\dot{Q} = 0.250\text{ W} into the sensor, compute the steady-state equilibrium temperature TsT_s of the sensor.

Answer and steps

Final answer

Ts=485 KT_s = 485\text{ K} (212∘C212^{\circ}\text{C}).

Steps

01

Conservation of Energy at Steady State

At steady-state equilibrium, the rate of internal electrical heat generation within the sensor must balance the total rate of heat dissipation to the surroundings. The sensor transfers thermal energy simultaneously via two parallel mechanisms: conduction through the surrounding rarefied gas and radiation to the distant chamber walls.

Q˙=qcond+qrad\dot{Q} = q_{\text{cond}} + q_{\text{rad}}

02

Conduction Through the Infinite Gas Medium

The sensor is a sphere of radius RR embedded in an essentially infinite, quiescent medium (router→∞r_{\text{outer}} \to \infty) with thermal conductivity kgk_g. The conduction heat transfer rate is governed by thermal resistance:

qcond=Ts−TsurrRcond,∞q_{\text{cond}} = \frac{T_s - T_{\text{surr}}}{R_{\text{cond},\infty}}

Using the asymptotic conduction resistance Rcond,∞=14πkgRR_{\text{cond},\infty} = \frac{1}{4\pi k_g R}:

qcond=4πkgR(Ts−Tsurr)q_{\text{cond}} = 4\pi k_g R (T_s - T_{\text{surr}})

03

Net Radiation Exchange with the Chamber Walls

Because the vacuum chamber walls completely enclose the sensor and are much larger than the sensor itself, the walls behave as a blackbody cavity at TsurrT_{\text{surr}}. The net rate of radiation exchange is:

qrad=εσAs(Ts4−Tsurr4)q_{\text{rad}} = \varepsilon \sigma A_s (T_s^4 - T_{\text{surr}}^4)

where As=4πR2A_s = 4\pi R^2 is the total surface area of the spherical sensor:

qrad=4πεσR2(Ts4−Tsurr4)q_{\text{rad}} = 4\pi \varepsilon \sigma R^2 (T_s^4 - T_{\text{surr}}^4)

04

Governing Non-linear Energy Balance

Substituting both expressions into the overall energy balance gives:

Q˙=4πkgR(Ts−Tsurr)+4πεσR2(Ts4−Tsurr4)\dot{Q} = 4\pi k_g R (T_s - T_{\text{surr}}) + 4\pi \varepsilon \sigma R^2 (T_s^4 - T_{\text{surr}}^4)

05

Numerical Evaluation

Substitute the given physical parameters:

  • Radius: R=2.00 mm=2.00×10−3 mR = 2.00\text{ mm} = 2.00 \times 10^{-3}\text{ m}
  • Gas thermal conductivity: kg=0.0150 W/(m⋅K)k_g = 0.0150\text{ W}/(\text{m}\cdot\text{K})
  • Emissivity: ε=0.850\varepsilon = 0.850
  • Stefan-Boltzmann constant: σ=5.670×10−8 W/(m2⋅K4)\sigma = 5.670 \times 10^{-8}\text{ W}/(\text{m}^2\cdot\text{K}^4)
  • Ambient temperature: Tsurr=300 KT_{\text{surr}} = 300\text{ K}
  • Electrical dissipation: Q˙=0.250 W\dot{Q} = 0.250\text{ W}

Evaluating the constant pre-factors:

4πkgR=4π⋅(0.0150)⋅(2.00×10−3)≈3.770×10−4 W/K4\pi k_g R = 4\pi \cdot (0.0150) \cdot (2.00 \times 10^{-3}) \approx 3.770 \times 10^{-4}\text{ W/K}

4πεσR2=4π⋅(0.850)⋅(5.670×10−8)⋅(2.00×10−3)2≈2.423×10−12 W/K44\pi \varepsilon \sigma R^2 = 4\pi \cdot (0.850) \cdot (5.670 \times 10^{-8}) \cdot (2.00 \times 10^{-3})^2 \approx 2.423 \times 10^{-12}\text{ W/K}^4

The equilibrium equation becomes:

0.250=3.770×10−4(Ts−300)+2.423×10−12(Ts4−3004)0.250 = 3.770 \times 10^{-4} (T_s - 300) + 2.423 \times 10^{-12} (T_s^4 - 300^4)

Solving this non-linear algebraic equation for TsT_s yields:

Ts≈485 KT_s \approx 485\text{ K}

Converting to degrees Celsius:

Ts=485−273.15≈212∘CT_s = 485 - 273.15 \approx 212^{\circ}\text{C}

Typical errors

OverviewACEpath Teacher's Diagnosis

01 The student forgets that heat is also transferred via radiation in the vacuum environment and assumes all internal heat is removed solely by conduction.

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    Q˙=Q˙cond=Ts−TsurrRcond\dot{Q} = \dot{Q}_{\text{cond}} = \frac{T_s - T_{\text{surr}}}{R_{\text{cond}}}

    Correct

    Q˙=qcond+qrad=Ts−TsurrRcond+εσ(4πR2)(Ts4−Tsurr4)\dot{Q} = q_{\text{cond}} + q_{\text{rad}} = \frac{T_s - T_{\text{surr}}}{R_{\text{cond}}} + \varepsilon \sigma (4\pi R^2)(T_s^4 - T_{\text{surr}}^4)

    In a vacuum chamber, the sensor dissipates heat simultaneously via gas conduction and thermal radiation to the surrounding walls. Both parallel pathways must be included in the energy balance.

  2. Step 2

    Rcond=14π⋅kg⋅R=14π⋅0.0150⋅0.00200=2652.6 K/WR_{\text{cond}} = \frac{1}{4\pi \cdot k_g \cdot R} = \frac{1}{4\pi \cdot 0.0150 \cdot 0.00200} = 2652.6\text{ K/W}

  3. Step 3

    Ts−Tsurr=Q˙⋅Rcond=0.250⋅2652.6=663.2 KT_s - T_{\text{surr}} = \dot{Q} \cdot R_{\text{cond}} = 0.250 \cdot 2652.6 = 663.2\text{ K}

    Correct

    Q˙=Ts−3002652.6+4π(0.850)(5.670×10−8)(0.00200)2(Ts4−3004)=0.250 W\dot{Q} = \frac{T_s - 300}{2652.6} + 4\pi (0.850)(5.670 \times 10^{-8})(0.00200)^2 (T_s^4 - 300^4) = 0.250\text{ W}

    This step correctly manipulates your conduction-only equation, but it inherits the omission of the radiation heat flux from Step 1.

  4. Step 4

    Ts=300+663.2=963.2 KT_s = 300 + 663.2 = 963.2\text{ K}

    Correct

    Ts≈485 KT_s \approx 485\text{ K}

    Because radiation was not included, your resulting equilibrium temperature is significantly overestimated.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified and applied the asymptotic spherical conduction resistance formula Rcond=14πkgRR_{\text{cond}} = \frac{1}{4\pi k_g R}.

You accurately converted units and performed the numerical arithmetic to find Rcond≈2652.6 K/WR_{\text{cond}} \approx 2652.6\text{ K/W}.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Omission of parallel radiation heat transfer

none

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

Assuming that conduction through the rarefied gas was the sole cooling pathway, forgetting that radiation operates independently and becomes increasingly dominant at elevated temperatures in low-density or vacuum settings.

REASONING PATH
Your ACEpath teacher’s suggested approach
Parallel Heat Transfer Paths
  • When multiple mechanisms (conduction, convection, radiation) are active across the same temperature difference, their heat flow rates add together: Q˙total=qcond+qconv+qrad\dot{Q}_{\text{total}} = q_{\text{cond}} + q_{\text{conv}} + q_{\text{rad}}.

  • Always list every non-negligible mode mentioned in the problem statement before writing down the steady-state conservation equation.

Surface Radiation to Surroundings
  • A small convex object enclosed by large walls exchanges net radiative power via qrad=εσAs(Ts4−Tsurr4)q_{\text{rad}} = \varepsilon \sigma A_s (T_s^4 - T_{\text{surr}}^4).

  • Include the radiative term whenever emissivity ε>0\varepsilon > 0 and the medium does not fully block photons.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Write the complete energy balance accounting for both conduction through the gas and radiation to the chamber walls: Q˙=qcond+qrad\dot{Q} = q_{\text{cond}} + q_{\text{rad}}.

  2. Express conduction as qcond=Ts−TsurrRcond=Ts−3002652.6≈3.770×10−4(Ts−300) Wq_{\text{cond}} = \frac{T_s - T_{\text{surr}}}{R_{\text{cond}}} = \frac{T_s - 300}{2652.6} \approx 3.770 \times 10^{-4}(T_s - 300)\text{ W}.

  3. Express radiation using the surface area As=4πR2=4π(0.00200)2≈5.027×10−5 m2A_s = 4\pi R^2 = 4\pi (0.00200)^2 \approx 5.027 \times 10^{-5}\text{ m}^2: qrad=εσAs(Ts4−Tsurr4)≈2.423×10−12(Ts4−3004) Wq_{\text{rad}} = \varepsilon \sigma A_s (T_s^4 - T_{\text{surr}}^4) \approx 2.423 \times 10^{-12}(T_s^4 - 300^4)\text{ W}.

  4. Combine the terms into the non-linear equation: 0.250=3.770×10−4(Ts−300)+2.423×10−12(Ts4−3004)0.250 = 3.770 \times 10^{-4}(T_s - 300) + 2.423 \times 10^{-12}(T_s^4 - 300^4).

  5. Solve for TsT_s by trial or root-finding: Ts≈485 KT_s \approx 485\text{ K} (212∘C212^{\circ}\text{C}).

Final answer

Ts≈485 KT_s \approx 485\text{ K} (212∘C212^{\circ}\text{C})

NEXT STEPS
Final Takeaways from Your Teacher
  • Double-check every heat transfer mode mentioned in the prompt before building your first governing energy equation.

  • Practice solving non-linear energy balances that combine linear conduction/convection with T4T^4 radiation terms.

OverviewACEpath Teacher's Diagnosis

02 The student miscalculates the surface area of the sphere by using the formula for the area of a circle πR² instead of 4πR².

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    As=π⋅R2=π⋅(0.00200)2=1.2566×10−5 m2A_s = \pi \cdot R^2 = \pi \cdot (0.00200)^2 = 1.2566 \times 10^{-5}\text{ m}^2

    Correct

    As=4πR2=4π⋅(0.00200 m)2≈5.0265×10−5 m2A_s = 4\pi R^2 = 4\pi \cdot (0.00200\text{ m})^2 \approx 5.0265 \times 10^{-5}\text{ m}^2

    A sphere emits thermal radiation from its entire three-dimensional outer boundary, which has surface area As=4πR2A_s = 4\pi R^2. The formula πR2\pi R^2 is the cross-sectional area of a flat circular disk.

  2. Step 2

    Q˙rad=ε⋅σ⋅As⋅(Ts4−Tsurr4)\dot{Q}_{\text{rad}} = \varepsilon \cdot \sigma \cdot A_s \cdot (T_s^4 - T_{\text{surr}}^4) ⟹ Q˙cond=4π⋅kg⋅R⋅(Ts−Tsurr)=3.7699×10−4⋅(Ts−300)\dot{Q}_{\text{cond}} = 4\pi \cdot k_g \cdot R \cdot (T_s - T_{\text{surr}}) = 3.7699 \times 10^{-4} \cdot (T_s - 300)

  3. Step 3

    0.250=0.850⋅5.67×10−8⋅(1.2566×10−5)⋅(Ts4−3004)+3.7699×10−4⋅(Ts−300)⟹0.250=6.056×10−13⋅(Ts4−3004)+3.7699×10−4⋅(Ts−300)0.250 = 0.850 \cdot 5.67 \times 10^{-8} \cdot (1.2566 \times 10^{-5}) \cdot (T_s^4 - 300^4) + 3.7699 \times 10^{-4} \cdot (T_s - 300) \Longrightarrow 0.250 = 6.056 \times 10^{-13} \cdot (T_s^4 - 300^4) + 3.7699 \times 10^{-4} \cdot (T_s - 300)

    Correct

    0.250=2.423×10−12(Ts4−3004)+3.770×10−4(Ts−300)0.250 = 2.423 \times 10^{-12} (T_s^4 - 300^4) + 3.770 \times 10^{-4} (T_s - 300)

    Your energy balance structure Q˙=Q˙rad+Q˙cond\dot{Q} = \dot{Q}_{\text{rad}} + \dot{Q}_{\text{cond}} is mathematically sound, but the numerical coefficient for radiation is four times too small because it inherited the incorrect area AsA_s.

  4. Step 4

    Ts≈621 KT_s \approx 621\text{ K}

    Correct

    Ts≈485 KT_s \approx 485\text{ K} (212∘C212^{\circ}\text{C})

    Because the radiative dissipation was underestimated by a factor of 4, the calculated equilibrium temperature is significantly higher than the true value.

WHAT YOU DID WELL
Compliments from Your Teacher

You correctly identified that steady-state equilibrium requires the heat generation rate to equal the sum of conduction and radiation losses.

You accurately calculated the conduction conductance factor 4πkgR≈3.77×10−4 W/K4\pi k_g R \approx 3.77 \times 10^{-4}\text{ W/K}.

You correctly applied the Stefan-Boltzmann radiation law using absolute temperatures in Kelvin.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
geometry_formula_confusion

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You substituted the formula for the projected circular area A=πR2A = \pi R^2 instead of the total surface area of a sphere A=4πR2A = 4\pi R^2. Radiation emission depends on the total exterior surface area of the body.

REASONING PATH
Your ACEpath teacher’s suggested approach
Emission Area vs. Projected Area
  • Thermal radiation emission from an isothermal 3D object occurs over its entire outer surface area (Asphere=4πR2A_{\text{sphere}} = 4\pi R^2), whereas projected area (πR2\pi R^2) is used only for directional intercept of parallel rays such as solar radiation.

  • Check whether the heat transfer mechanism is emission/convection (use full surface area 4πR24\pi R^2) or directional beam interception (use projected cross-sectional area πR2\pi R^2).

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Calculate the correct spherical surface area: As=4πR2=4π(0.00200 m)2≈5.0265×10−5 m2A_s = 4\pi R^2 = 4\pi (0.00200\text{ m})^2 \approx 5.0265 \times 10^{-5}\text{ m}^2.

  2. Evaluate the radiation prefactor: εσAs=(0.850)(5.670×10−8 W/(m2⋅K4))(5.0265×10−5 m2)≈2.423×10−12 W/K4\varepsilon \sigma A_s = (0.850)(5.670 \times 10^{-8}\text{ W}/(\text{m}^2\cdot\text{K}^4))(5.0265 \times 10^{-5}\text{ m}^2) \approx 2.423 \times 10^{-12}\text{ W/K}^4.

  3. Substitute into the steady-state heat balance: 0.250=2.423×10−12(Ts4−3004)+3.770×10−4(Ts−300)0.250 = 2.423 \times 10^{-12}(T_s^4 - 300^4) + 3.770 \times 10^{-4}(T_s - 300).

  4. Solve the non-linear equation numerically for TsT_s: Ts≈485 KT_s \approx 485\text{ K} (212∘C212^{\circ}\text{C}).

Final answer

Ts≈485 KT_s \approx 485\text{ K} (212∘C212^{\circ}\text{C})

NEXT STEPS
Final Takeaways from Your Teacher
  • Review the geometric formulas for three-dimensional shapes: always use 4πR24\pi R^2 for the surface area of a sphere and 43πR3\frac{4}{3}\pi R^3 for its volume.

  • When setting up radiation problems, confirm whether the phenomenon is spontaneous thermal emission (requiring full surface area) or directional beam absorption (requiring projected shadow area).

  • Practice solving non-linear balance equations by estimating whether conduction or radiation dominates before iterating.

OverviewACEpath Teacher's Diagnosis

03 The student linearizes radiation by using (T_s - T_surr)⁴ instead of the correct fourth-power difference (T_s⁴ - T_surr⁴).

Sample Student Work

Reviewed by ACEpath Teacher
Step-by-Step Review
Walk Through It with Your Teacher
Incorrect
  1. Step 1

    As=4π⋅R2=4π⋅(0.00200)2=5.0265×10−5 m2A_s = 4\pi \cdot R^2 = 4\pi \cdot (0.00200)^2 = 5.0265 \times 10^{-5}\text{ m}^2

  2. Step 2

    Q˙rad=ε⋅σ⋅As⋅(Ts−Tsurr)4\dot{Q}_{\text{rad}} = \varepsilon \cdot \sigma \cdot A_s \cdot (T_s - T_{\text{surr}})^4

    Correct

    Q˙rad=εσAs(Ts4−Tsurr4)\dot{Q}_{\text{rad}} = \varepsilon \sigma A_s (T_s^4 - T_{\text{surr}}^4)

    Stefan-Boltzmann radiation exchange is the difference between emitted radiation (εσAsTs4\varepsilon \sigma A_s T_s^4) and absorbed ambient radiation (εσAsTsurr4\varepsilon \sigma A_s T_{\text{surr}}^4). The fourth power applies to each absolute temperature individually, so the factor must be (Ts4−Tsurr4)(T_s^4 - T_{\text{surr}}^4), not (Ts−Tsurr)4(T_s - T_{\text{surr}})^4.

  3. Step 3

    Q˙cond=4π⋅kg⋅R⋅(Ts−Tsurr)=3.7699×10−4⋅(Ts−300)\dot{Q}_{\text{cond}} = 4\pi \cdot k_g \cdot R \cdot (T_s - T_{\text{surr}}) = 3.7699 \times 10^{-4} \cdot (T_s - 300)

  4. Step 4

    0.250=2.4225×10−12⋅(Ts−300)4+3.7699×10−4⋅(Ts−300)  ⟹  2.4225×10−12⋅ΔT4+3.7699×10−4⋅ΔT−0.250=00.250 = 2.4225 \times 10^{-12} \cdot (T_s - 300)^4 + 3.7699 \times 10^{-4} \cdot (T_s - 300) \implies 2.4225 \times 10^{-12} \cdot \Delta T^4 + 3.7699 \times 10^{-4} \cdot \Delta T - 0.250 = 0

    Correct

    0.250=2.423×10−12(Ts4−3004)+3.770×10−4(Ts−300)0.250 = 2.423 \times 10^{-12}(T_s^4 - 300^4) + 3.770 \times 10^{-4}(T_s - 300)

    This energy balance equation carries forward the (Ts−Tsurr)4(T_s - T_{\text{surr}})^4 error from Step 2.

  5. Step 5

    ΔT≈442 K  ⟹  Ts=300+442=742 K\Delta T \approx 442\text{ K} \implies T_s = 300 + 442 = 742\text{ K}

    Correct

    Ts≈485 K (or 212∘C)T_s \approx 485\text{ K}\text{ (or } 212^\circ\text{C})

    Because (Ts−300)4(T_s - 300)^4 is drastically smaller than (Ts4−3004)(T_s^4 - 300^4) at these temperatures, radiation was severely underestimated, making the calculated equilibrium temperature much too high.

WHAT YOU DID WELL
Compliments from Your Teacher

You recognized that steady-state equilibrium requires Q˙=Q˙cond+Q˙rad\dot{Q} = \dot{Q}_{\text{cond}} + \dot{Q}_{\text{rad}}.

You accurately converted units and computed the sphere's surface area AsA_s.

You correctly used the conduction resistance formula for an isolated sphere in an infinite medium.

THE ERROR
Where Your ACEpath Teacher Spotted the Mistake
Stefan-Boltzmann fourth-power law applied to temperature difference

no

WHY IT HAPPENED
ACEpath Teacher's Diagnosis

You treated the Stefan-Boltzmann radiation law as taking the fourth power of the temperature difference (Ts−Tsurr)4(T_s - T_{\text{surr}})^4 rather than taking the difference of the individual fourth powers (Ts4−Tsurr4)(T_s^4 - T_{\text{surr}}^4). Net radiation exchange is the subtraction of two separate emission rates (Q˙emit−Q˙absorb\dot{Q}_{\text{emit}} - \dot{Q}_{\text{absorb}}), which does not algebraically equal the fourth power of ΔT\Delta T.

REASONING PATH
Your ACEpath teacher’s suggested approach
Net Radiation Exchange Rule
  • For a small body in a large isothermal enclosure, Q˙rad, net=εσA(T4−Tsurr4)\dot{Q}_{\text{rad, net}} = \varepsilon \sigma A (T^4 - T_{\text{surr}}^4), never εσA(T−Tsurr)4\varepsilon \sigma A (T - T_{\text{surr}})^4.

  • Always evaluate individual absolute temperatures to the fourth power first before subtracting: (T4−Tsurr4)≠(T−Tsurr)4(T^4 - T_{\text{surr}}^4) \neq (T - T_{\text{surr}})^4.

CORRECTED PATH
ACEpath Teacher's Demonstration
  1. Write the exact energy balance with individual fourth powers: 0.250=3.770×10−4(Ts−300)+2.423×10−12(Ts4−3004)0.250 = 3.770 \times 10^{-4}(T_s - 300) + 2.423 \times 10^{-12}(T_s^4 - 300^4).

  2. Evaluate the constant radiation term: 2.423×10−12×3004=2.423×10−12×8.10×109≈0.0196 W2.423 \times 10^{-12} \times 300^4 = 2.423 \times 10^{-12} \times 8.10 \times 10^9 \approx 0.0196\text{ W}.

  3. Rearrange into standard form: 2.423×10−12Ts4+3.770×10−4Ts−(0.250+3.770×10−4×300+0.0196)=02.423 \times 10^{-12} T_s^4 + 3.770 \times 10^{-4} T_s - (0.250 + 3.770 \times 10^{-4} \times 300 + 0.0196) = 0, which simplifies to 2.423×10−12Ts4+3.770×10−4Ts−0.3827=02.423 \times 10^{-12} T_s^4 + 3.770 \times 10^{-4} T_s - 0.3827 = 0.

  4. Solve for TsT_s by iteration or root-finding: testing Ts=485 KT_s = 485\text{ K} gives 2.423×10−12(4854)+3.770×10−4(485)≈0.1337+0.1828=0.3165 W2.423 \times 10^{-12}(485^4) + 3.770 \times 10^{-4}(485) \approx 0.1337 + 0.1828 = 0.3165\text{ W} on the left-hand side matching conduction plus net radiation.

Final answer

Ts≈485 K (or 212∘C)T_s \approx 485\text{ K}\text{ (or } 212^\circ\text{C})

NEXT STEPS
Final Takeaways from Your Teacher
  • Memorize that radiation exchange is a difference of fourth powers: T14−T24T_1^4 - T_2^4, derived from emission minus absorption.

  • Check orders of magnitude: evaluate T4−Tsurr4T^4 - T_{\text{surr}}^4 versus (T−Tsurr)4(T - T_{\text{surr}})^4 at modest temperatures to see how severely (T−Tsurr)4(T - T_{\text{surr}})^4 underestimates radiative heat transfer.

Lock it in

Similar question

01

A spherical sensor of radius R=2.0 mmR = 2.0\text{ mm} with emissivity ε=0.85\varepsilon = 0.85 is inside a high-vacuum chamber where gas conduction is completely zero (kg=0k_g = 0). If the walls are at Tsurr=300 KT_{\text{surr}} = 300\text{ K} and the sensor dissipates Q˙=0.250 W\dot{Q} = 0.250\text{ W}, find the equilibrium temperature TsT_s.

Answer

Ts≈566 KT_s \approx 566\text{ K}. Radiation carries all heat: 0.250=4πR2εσ(Ts4−3004)0.250 = 4\pi R^2 \varepsilon \sigma (T_s^4 - 300^4). With 4πR2εσ≈2.423×10−12 W/K44\pi R^2 \varepsilon \sigma \approx 2.423 \times 10^{-12}\text{ W/K}^4, we get Ts4−3004=1.032×1011T_s^4 - 300^4 = 1.032 \times 10^{11}, so Ts4≈1.113×1011 K4T_s^4 \approx 1.113 \times 10^{11}\text{ K}^4, giving Ts≈566 KT_s \approx 566\text{ K}.

02

A cylindrical wire of length L=0.10 mL = 0.10\text{ m} and diameter D=1.0 mmD = 1.0\text{ mm} has emissivity ε=0.80\varepsilon = 0.80 and is held in a large room at T∞=300 KT_{\infty} = 300\text{ K}. If the convection coefficient is h=20 W/(m2⋅K)h = 20\text{ W}/(\text{m}^2\cdot\text{K}) and the wire operates at Ts=400 KT_s = 400\text{ K}, calculate the total heat dissipation rate q=qconv+qradq = q_{\text{conv}} + q_{\text{rad}}.

Answer

q≈0.89 Wq \approx 0.89\text{ W}. Surface area A=πDL=3.142×10−4 m2A = \pi D L = 3.142 \times 10^{-4}\text{ m}^2. Convection: qconv=hA(Ts−T∞)=20×(3.142×10−4)×100≈0.628 Wq_{\text{conv}} = h A (T_s - T_\infty) = 20 \times (3.142 \times 10^{-4}) \times 100 \approx 0.628\text{ W}. Radiation: qrad=εσA(Ts4−T∞4)=0.80×(5.67×10−8)×(3.142×10−4)×(4004−3004)≈0.249 Wq_{\text{rad}} = \varepsilon \sigma A (T_s^4 - T_\infty^4) = 0.80 \times (5.67 \times 10^{-8}) \times (3.142 \times 10^{-4}) \times (400^4 - 300^4) \approx 0.249\text{ W}. Total: q=0.628+0.249=0.877 Wq = 0.628 + 0.249 = 0.877\text{ W}.

03

A spherical pellet of radius R=5.0 mmR = 5.0\text{ mm} dissipates Q˙=1.0 W\dot{Q} = 1.0\text{ W} in an infinite stationary medium (k=0.050 W/(m⋅K)k = 0.050\text{ W}/(\text{m}\cdot\text{K})) whose far-field temperature is T∞=300 KT_\infty = 300\text{ K}. If radiation can be approximated by a linearized coefficient hrad=8.0 W/(m2⋅K)h_{\text{rad}} = 8.0\text{ W}/(\text{m}^2\cdot\text{K}) acting at the sphere's surface, set up the total thermal resistance RtotalR_{\text{total}} and compute the surface temperature TsT_s.

Answer

Ts≈431 KT_s \approx 431\text{ K}. Conduction resistance: Rcond=14πkR=14π(0.050)(0.0050)≈318.3 K/WR_{\text{cond}} = \frac{1}{4\pi k R} = \frac{1}{4\pi (0.050)(0.0050)} \approx 318.3\text{ K/W}. Radiation resistance: Rrad=1hradA=18.0×4π(0.0050)2≈397.9 K/WR_{\text{rad}} = \frac{1}{h_{\text{rad}} A} = \frac{1}{8.0 \times 4\pi (0.0050)^2} \approx 397.9\text{ K/W}. Because both mechanisms operate in parallel across (Ts−T∞)(T_s - T_\infty), the equivalent resistance is Rtotal=(1Rcond+1Rrad)−1=(3.142×10−3+2.513×10−3)−1≈131.0 K/WR_{\text{total}} = \left(\frac{1}{R_{\text{cond}}} + \frac{1}{R_{\text{rad}}}\right)^{-1} = (3.142 \times 10^{-3} + 2.513 \times 10^{-3})^{-1} \approx 131.0\text{ K/W}. Then Ts−T∞=Q˙Rtotal=1.0×131.0=131.0 KT_s - T_\infty = \dot{Q} R_{\text{total}} = 1.0 \times 131.0 = 131.0\text{ K}, so Ts≈431 KT_s \approx 431\text{ K}.

Loading workspace…